Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “developable planes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Weight Saving Technology

The airplane shown below is the Beech Super King Air, an executive transport built by Beech Aircraft corporation, Wichita, Kansas. Its development was aided by the NASA computer program known as NASTRAN(Registered TradeMark) (NASA Structural Analysis), which electronically analyzes a computerized design and predicts how it will react to many different conditions of stress and strain. In this instance the program was employed in analysis of the airplane's structure and engine mounts. NASTRAN was similarly used in development of other Beech planes, such as the T-34C military trainer and the new single-engine Skipper light-plane, which is making its debut this year. At its Boulder, Colorado facility, Beech has used NASTRAN in analysis of fuel tanks for space vehicles. The company reports it has achieved cost savings and improved its design/analysis capabilities through use of the NASA program. NASTRAN and other government-generated computer programs are made available to industry through NASA's Computer Software Management and Information Center (COSMIC)(Registered TradeMark) at the University of Georgia.

Source record↗
NASA NTRS2003

Engineered Carbon Nanotube Materials for High-Q Nanomechanical Resonators

This document represents a presentation offered by the Jet Propulsion Laboratory, with assistance from researchers from Brown University and Northrop Grumman. The presentation took place in Seoul, Korea in July 2003 and attempted to demonstrate the fabrication approach regarding the development of high quality factor (high-Q) mechanical oscillators (in the forms of a tunable nanotube resonator and a nanotube array radio frequency [RF] filter) aimed at signal processing and based on carbon nanotubes. The presentation also addressed parallel efforts to develop both in-plane single nanotube resonators as well as vertical array power devices.

chemical vapor depositions↗
NASA NTRS2018

Fabrication of a Hybrid Transition Edge Sensor Array for Lynx

Lynx is a proposed NASA X-Ray telescope flight mission aimed at achieving state-of-the-art angular and energy resolution with a 100 kilopixel array to probe the hot energetic young universe in unprecedented detail. To achieve these goals, our team plans on leveraging our current work in development of the focal plane for the Athena X-Ray Integral Field Unit (X-IFU) while advancing the state-of-the-art in transition edge sensor (TES) X-ray detector technology. The TES is an optimal technology for achieving both high energy and fine angular resolution at the same time because pixel features can be made extremely small and the absorber which dominates the heat capacity can be tuned to meet resolution requirements. Specifically, the proposed mission concept calls for a hybrid detector of three different arrays fabricated in the same planar process in one focal plane and optimized for different science goals. The main arrays consist of 5x5 hydras, 25 pixels of 4 micron thick Au absorbers each with a different thermal link to one common TES. The outer array has absorbers on a 50-micron pitch for most of the 5 arc-minute field-of-view, and the inner array has 25-micron absorbers for the central 1 arc-minute region. A high resolution array consisting of single pixel 1 micron thick Au absorbers on 50-micron pitch will lie off to the side. Reading out an array of this magnitude will likely require improvements in indium bump bonding to superconducting flexible wiring. Fabrication of absorbers of two different sizes requires electroplating through a photoresist mold by careful tuning of the current density to achieve uniform flat absorbers on a fine pitch scale, followed by ion milling to yield narrow streets separating the pixels while preserving high quantum efficiency. We report on progress made at fabricating the hybrid array with different absorber sizes and thicknesses. Further, we also report on ongoing work to adequately heat sink the pixels with backside wire bonding and copper coating. We also report on work to improve detector pixel yield and top side indium bump bonding to flexible wiring.

Focal plane array↗
NASA NTRS2023

Establishing a Pathway to Greener Aviation

The burning and production of jet fuel in both commercial and regional planes at a high volume releases extreme levels of carbon emission as of its current state. This paper analyzes the implementation and benefits of three sustainable alternatives to traditional jet fuel: sustainable aviation fuel (SAF), hydrogen fuel cells, and electric batteries. A roadmap to show progress in reducing the carbon footprint of aviation is then proposed. The first phase of the roadmap involves the evolution of technology, validation, and testing of SAF-powered planes and the preliminary development of hydrogen production and propulsion and battery technology and the development of electric propulsion technologies. The second phase illustrates the widespread implementation of all three fuel sources where electric aviation will be enforced in short-range travel (30 min-3 hrs), medium-range aircraft (3-6 hrs) will use hydrogen fuel cells, and long-range (6+ hrs) airliners will utilize SAF. The third and final phase will enact the use of SAF and electric batteries for long-range applications while hydrogen fuel cells will dominate short- and medium-range aircraft. This roadmap, in combination with proper legislative action and corporate cooperation paired with public awareness, can help eliminate the usage of jet fuel in the aviation industry and replace it with three more sustainable and clean fuel sources.

green aviation↗
NASA NTRS1992

Phasing of a space based segmented submillimeter wavelength telescope using focal plane measurements

As part of a technology development program for realizing a space based submillimeter telescope, two different approaches to the absolute phasing of a segmented primary mirror using focal plane measurements have been implemented for feasibility. The method of optimization by simulated annealing evaluates the image quality of a point spread function after all the telescope segments have been randomly moved. It accepts each iteration which improves the image quality, as well as a random number of iterations which do not, thus keeping the Strehl in the initialization procedure from falling into local maxima. Methods for determining the annealing schedule, and the step size for random segment movements are presented and discussed. Using phase diversity and a model for the telescope imaging system, a nonlinear least squares algorithm has also been implemented which parameterizes each of the segment actuator movements. Using multiple out of focus images, the segment actuator positions are estimated using an iterative procedure. Nonlinear least squares, although computationally intensive, offers a large savings in the actuator movements over simulated annealing and pairwise phasing methods for large numbers of segments. These algorithms have been integrated into a general simulation program which models the behavior of the telescope under anticipated space conditions.

Levine, B. M.↗
NASA NTRS2012

Fabrication of a Cryogenic Bias Filter for Ultrasensitive Focal Plane

A fabrication process has been developed for cryogenic in-line filtering for the bias and readout of ultrasensitive cryogenic bolometers for millimeter and submillimeter wavelengths. The design is a microstripline filter that cuts out, or strongly attenuates, frequencies (10 50 GHz) that can be carried by wiring staged at cryogenic temperatures. The filter must have 100-percent transmission at DC and low frequencies where the bias and readout lines will carry signal. The fabrication requires the encapsulation of superconducting wiring in a dielectric-metal envelope with precise electrical characteristics. Sufficiently thick insulation layers with high-conductivity metal layers fully surrounding a patterned superconducting wire in arrayable formats have been demonstrated. A degenerately doped silicon wafer has been chosen to provide a metallic ground plane. A metallic seed layer is patterned to enable attachment to the ground plane. Thick silicon dioxide films are deposited at low temperatures to provide tunable dielectric isolation without degrading the metallic seed layer. Superconducting wiring is deposited and patterned using microstripline filtering techniques to cut out the relevant frequencies. A low Tc superconductor is used so that it will attenuate power strongly above the gap frequency. Thick dielectric is deposited on top of the circuit, and then vias are patterned through both dielectric layers. A thick conductive film is deposited conformally over the entire circuit, except for the contact pads for the signal and bias attachments to complete the encapsulating ground plane. Filters are high-aspect- ratio rectangles, allowing close packing in one direction, while enabling the chip to feed through the wall of a copper enclosure. The chip is secured in the copper wall using a soft metal seal to make good thermal and electrical contact to the outer shield.

Chervenak, James↗
NASA NTRS1992

On development of a finite dynamic element and solution of associated eigenproblem by a block Lanczos procedure

The paper first presents the details of the development of a new six-noded plane triangular finite dynamic element. A block Lanczos algorithm is developed next for the accurate and efficient solution of the quadratic matrix eigenvalue problem associated with the finite dynamic element formulation. The resulting computer program fully exploits matrix sparsity inherent in such a discretization and proves to be most efficient for the extraction of the usually required first few roots and vectors, including repeated ones. Most importantly, the present eigenproblem solution is shown to be comparable to that of the corresponding finite element analysis, thereby rendering the associated dynamic element method rather attractive owing to superior convergence characteristics of such elements, presented herein.

Gupta, K. K.↗
NASA NTRS1992

Technologies for the National Aero-Space Plane

Technologies for SSTO and hypersonic atmospheric cruise flight being developed in the context of the National Aero-Space Plane (NASP) program are discussed. Emphasis is given to research in aerothermodynamics, propulsion, fuel technology, structures and materials, vehicle management systems, and CVD and instrumentation tools. Brief attention is also given to the X-30 vehicle and to long-term applications of NASP technologies.

Rausch, Vincent L.↗
NASA NTRS1975

Radiative transfer in a plane stratified dielectric

A model is developed for calculating radiative transfer in a stratified dielectric. This model is used to show that the reflectivity of a stratified dielectric is primarily determined by gradients in the real part of the refractive index over distances on the order of 1/10 wavelength in the medium. The effective temperature of the medium is determined by the thermodynamic temperature profile over distances of the order delta T.

Wilheit, T. T., Jr.↗
NASA NTRS1978

The execution of systematic measurements on plane cascades

The present state of development of the experimental technique regarding the flow through cascades and several points to be specially observed in the design of cascade wind tunnels were discussed. The equations required for the evaluation of the momentum measurements in two dimensional flow through cascades were developed. Regarding the effect of the jet contraction due to the boundary layer along the side walls a simple method for correction was also given in order to obtain two dimensional flow characteristics. Also given were the equations for the evaluation of the pressure distribution measurements. Another contribution was made regarding the presentation of the test results in the form of nondimensional quantities. The results of systematic measurements of cascades with symmetrical aerofoil were reported, and the above suggested method was applied for the evaluation of the measurements.

Scholz, N.↗
NASA NTRS1988

Dynamics of coherent structures in a plane mixing layer

An incompressible, time developing 3-D mixing layer with idealized initial conditions was simulated numerically. Consistent with the suggestions from experimental measurements, the braid region between the dominant spanwise vortices or rolls develops longitudinal vortices or ribs, which are aligned upstream and downstream of a roll and produce spanwise distortion of the rolls. The process by which this distortion occurs is explained by studying a variety of quantities of dynamic importance (e.g., production of enstrophy, vortex stretching). Other quantities of interest (dissipation, helicity density) are also computed and discussed. The currently available simulation only allows the study of the early evolution (before pairing) of the mixing layer. New simulations in progress will relieve this restriction.

Hussain, Fazle↗
NASA NTRS1991

Space Shuttle Main Engine nozzle mounted optic for throat plane spectroscopy

A program intended to develop a flight-capable nozzle mounted optic for monitoring emissions from metals entrained in the Space Shuttle Main Engine (SSME) flowfield is described. The optic will collect light emitted from metal atoms within the high-temperature, high-pressure SSME chamber and transfer the optical signal to a high-resolution spectrometer via a fiber-optic cable. The nozzle mounted optic makes it possible to conduct earth-to-orbit monitoring of flowfield emissions without requiring modifications to the SSME.

Bickford, R. L.↗
NASA NTRS2010

An Aircraft Separation Algorithm with Feedback and Perturbation

A separation algorithm is a set of rules that tell aircraft how to maneuver in order to maintain a minimum distance between them. This paper investigates demonstrating that separation algorithms satisfy the FAA requirement for the occurrence of incidents by means of simulation. Any demonstration that a separation algorithm, or any other aspect of flight, satisfies the FAA requirement is a challenge because of the stringent nature of the requirement and the complexity of airspace operations. The paper begins with a probability and statistical analysis of both the FAA requirement and demonstrating meeting it by a Monte Carlo approach. It considers the geometry of maintaining separation when one plane must change its flight path. It then develops a simple feedback control law that guides the planes on their paths. The presence of feedback control permits the introduction of perturbations, and the stochastic nature of the chosen perturbation is examined. The simulation program is described. This paper is an early effort in the realistic demonstration of a stringent requirement. Much remains to be done.

White, Allan L.↗
NASA NTRS1981

Approximate heating analysis for the windward-symmetry plane of Shuttle-like bodies at large angle of attack

An engineering method has been developed for computing the windward-symmetry plane convective heat-transfer rates on Shuttle-like vehicles at large angles of attack. The engineering code includes an approximate inviscid flowfield technique, laminar and turbulent heating-rate expressions, an approximation to account for the variable-entropy effects on the surface heating and the concept of an equivalent axisymmetric body to model the windward-ray flowfields of Shuttle-like vehicles at angles of attack from 25 to 45 degrees. The engineering method is validated by comparing computed heating results with corresponding experimental data measured on Shuttle and advanced transportation models over a wide range of flow conditions and angles of attack from 25 to 40 degrees and also with results of existing prediction techniques. The comparisons are in good agreement.

Zoby, E. V.↗
NASA NTRS1989

Guidance analysis of the aeroglide plane change maneuver as a turning point problem

The development of guidance approximations for the atmospheric (aeroglide) portion of the minimum fuel, orbital plane change, trajectory optimization problem is described. Asymptotic methods are used to reduce the two point, boundary value, optimization problem to a turning point problem from the bank angle control. The turning point problem solution, which yields an approximate optimal control policy, is given in terms of parabolic cylinder functions, which are tabulated, and integral expressions, which must be numerically computed. Comparisons of the former, over their region of validity, with optimal control solutions show good qualitative agreement. Additional work and analysis is needed to compute the guidance approximation work.

Gracey, Christopher↗