Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “current generation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Field Test Bed for Vadose-Zone Monitoring Approaches - 20404

In the Central Plateau at the U.S. Department of Energy Hanford Site, a large inventory of contaminants resides in unsaturated sediments within the approximately 100-meter-thick vadose zone, posing a potential continuing risk to groundwater. Vadose zone remedies used to address these contaminants will require performance monitoring to provide feedback during implementation and for long-term verification that remedial action objectives have been met. Passive approaches may also need long-term monitoring to demonstrate that the flux of contaminants from the vadose zone to the groundwater are below thresholds established to meet groundwater protection goals. Collection of physical (e.g., groundwater or sediment) samples is a common method for identifying contaminant concentration distributions, but this approach is limited by the number of locations and the frequency with which data can be collected. In situ vadose zone measurements have evolved over the past few years to include key measurements of water content, soil water pressure, temperature, and chemical concentration. However, the current generation of sensors is designed for relatively short-term use in near-surface soils or sediments. Geophysical methods have been evolving but are also limited in that they have not been designed for the specific long-term vadose zone monitoring needs at the Hanford Site. Overall, monitoring under unsaturated conditions can be difficult due to the need to install and maintain instrumentation over a large area and depth and the need to identify preferential flow pathways due to geologic and chemical heterogeneities over long periods. Thus, a vadose zone monitoring test bed was initiated to address these challenges and identify cost-effective approaches for implementation and postclosure monitoring of the deep vadose zone. The monitoring test bed is expected to provide valuable field-scale information for the design of vadose zone monitoring systems. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

1.1 eV GaInAs Cell Development for Dual-Use Solar and 1075 nm Laser Power Converters

Dual-use power converter cells can receive solar and laser power simultaneously to generate current, an application relevant to space and terrestrial industries. This study investigates two concepts of solar cells optimized for dual- use 1070 nm laser and solar power conversion, a single-junction and triple-junction cell. Because it is bandgap-tuned for a 1070 nm laser, the 1.1 eV junction is incorporated into each of the two designs, making its development key to the success of both concepts. Efficiency data for a one junction GaInAs cell demonstrates a laser conversion efficiency of 38% at 1070nm wavelength without an anti-reflection coating. However, the single-junction device requires optimization to reduce short wavelength absorption of the broad solar spectrum. In both devices, the graded buffer layers in the GaInAs cell affects the cell's performance by reducing threading dislocations in the active junction. However, the buffer in the three-junction device also acts as a lateral transport layer and so affects the fill factor depending on its sheet resistance. By varying the buffer thickness, we demonstrate a direct relationship between buffer thickness and sheet resistance reduction, while considering implications to open-circuit voltages. We also performed resistance modeling to determine the optimal grid spacing and thickness of the grid fingers to minimize losses due to sheet resistance and grid shading.

dual-use↗
DOE OSTI2026

A New Window into the Baryon Cycle at Cosmic Noon with Line Intensity Mapping: Forecasts for auto- and cross-correlations in [CII]-158$μ$m, HI 21 cm, CO$_{J+1\rightarrow J}$, and H$α$ galaxies

Across the peak of cosmic star formation at $z\sim1-2$, inflow, processing, and feedback drive rapid changes in the spatial distribution and chemical composition of baryons in galaxies and surrounding reservoirs; this baryon cycle can be tomographically mapped by line intensity mapping (LIM) of atomic hydrogen, ionized carbon, and carbon monoxide. We present a simulation-based forecasting framework for detecting auto- and cross-power spectra between spectroscopic surveys of four such tracers at $z\sim0.5-1.7$ mapping the same deep field - TIM, EoRSpec/FYST, MeerKAT, & Euclid. We forward-model 3-D distributions for these tracers from magnetohydrodynamic simulations, directly capturing the two-halo, one-halo, and shot statistics without relying on analytical decompositions. We further detail a signal-to-noise formalism, tailored to LIM surveys with highly anisotropic geometries and Fourier-space coverage. We demonstrate that galaxy cross-correlations will be the dominant discovery channel for current-generation surveys. These instruments will detect the auto-spectra for CO and HI 21 cm and the CO $\times$ 21 cm cross-spectrum at modest S/N $\sim 1-10$, while placing upper limits on the [CII]-158$μ$m signals. [CII], CO, and HI LIM will be $\sim3-30\times$ ($0.5-1.5$ dex) more sensitive to cross-correlation with the Euclid survey, however, than their respective auto-correlations, constraining all three models of line emission at high significance (S/N $\sim 10-40$) within this decade. Finally, we formulate a staged instrumental trajectory with planned or reasonable improvements, including the as-proposed SKA-Mid. We forecast advancing the per-$k$-mode sensitivities of each auto-, galaxy-line, and line-line spectrum by several orders of magnitude, enabling new percent- and sub-percent level constraints on cosmology and the redshift evolution of star formation and the baryon cycle.

Agrawal, Shubh [Pennsylvania U., Dept. Math.]↗
DOE OSTI2021

Superconducting RF Gun with High Current and the Capability to Generate Polarized Electron Beams

High-current low-emittance CW electron beams are indispensable for nuclear and high-energy physics fixed target and collider experiments, cooling high energy hadron beams, generating CW beams of monoenergetic X-rays (in FELs) and gamma-rays (in Compton sources). Polarization of electrons in these beams provides extra value by opening a new set of observables and frequently improving the data quality. We report on the upgrade of the unique and fully functional CW SRF 1.25 MeV SRF gun, built as part of the Coherent electron Cooling (CeC) project, which has demonstrated sustained CW operation with CsK2Sb photocathodes generating electron bunches with record-low transverse emittances and record-high bunch charge exceeding 10 nC. We propose to extend the capabilities of this system to high average current of 100 milliampere in two steps: increasing the current 30-fold at each step with the goal to demonstrate reliable long-term operation of the high-current low-emittance CW SRF guns. We also propose to test polarized GaAs photocathodes in the ultra-high vacuum (UHV) environment of the SRF gun, which has never been successfully demonstrated in RF accelerators.

43 PARTICLE ACCELERATORS↗
DOE OSTI2024

Advanced multimaterial shape optimization methods as applied to advanced manufacturing of wind turbine generators

Abstract Currently, many utility‐scale wind turbine generator original equipment manufacturers are dependent on imported rare earth permanent magnets, which are susceptible to market risks from cost instability. To lower the production costs of these generators and stay competitive in the market, several small wind manufacturers are pursuing continuous improvements to both generator design and manufacturing. However, traditional design and manufacturing methods have yielded marginal improvements in wind power performance. This work presents novel methods to redesign a baseline 15‐kW wind turbine generator with reduced rare‐earth permanent magnets by leveraging cutting‐edge three‐dimensional (3D) printed polymer‐bonded permanent magnets and steel. Symmetric, asymmetric, and multimaterial‐magnet parametrization methods are introduced for shape optimization. We extend the symmetric and asymmetric methods to the back iron in the stator to further investigate the impact and opportunities for performance improvements with lesser active materials. We employ a design‐of‐experiments approach with parametric computer‐aided design for shape generation and evaluate different designs by magneto‐thermal modeling and finite‐element analysis. We use adaptive sampling technique to identify better performing designs with lesser magnet mass, higher efficiency, and lower cogging torque when compared with the baseline generator. Asymmetric pole designs resulted in a magnet mass in the range of 4.77–5.37 kg, which was 27%–35% lighter than the baseline generator, suggesting that a new design freedom exists that can be enabled by advanced manufacturing, such as 3D printing. Shaping the back iron in the stator resulted in material savings in electrical steel of up to 14.62 kg, which was 20% lighter than the baseline stator. We conducted a structural analysis to evaluate an optimized asymmetric rotor design from the point of view of mechanical integrity and air‐gap stiffness. The magnetically optimal shape profile was shown as having a positive impact on the radial stiffness, and an optimal solution was discovered to reduce the structural mass by nearly 30 kg, which was 29% lighter than the baseline.

17 WIND ENERGY↗
DOE OSTI2021

Hybrid feature-driven learning system for abnormality detection and localization

A cyber-physical system may have a plurality of monitoring nodes each generating a series of current monitoring node values over time representing current operation of the system. A data-driven features extraction computer platform may receive the series of current monitoring node values and generate current data-driven feature vectors based on the series of current monitoring node values. A residual features extraction computer platform may receive the series of current monitoring node values, execute a system model and utilize a stochastic filter to determine current residual values, and generate current residual-driven feature vectors based on the current residual values. An abnormal detection platform may then receive the current data-driven and residual-driven feature vectors and compare the current data-driven and residual-driven feature vectors with at least one decision boundary associated with an abnormal detection model. An abnormal alert signal may then be transmitted when appropriate based on a result of said comparison.

Abbaszadeh, Masoud↗
DOE OSTI2022

Pulsed-Power Innovations for Next-Generation, High-Current Drivers

There are proposals to build larger high-current drivers to be used for high-energy-density physics (HEDP), inertial confinement fusion (ICF), radiation effects testing, and basic science. Drivers significantly larger than the Z Machine at Sandia National Laboratories, Albuquerque, NM, USA, encounter increasing difficulties in water power flow, insulator performance, and vacuum power flow. The physics requirements of imploding loads limit a designer’s flexibility in choosing machine parameters, such as current rise time, driving impedance, and total inductance. This article enumerates these physics constraints and shows how they impact driver design. Here, we conclude that advances in pulsed-power capabilities are needed to control risk and to build a cost-effective driver at peak currents of ~60 MA.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Rotor blade imbalance fault detection for variable-speed marine current turbines via generator power signal analysis

Marine hydrokinetic (MHK) turbines extract renewable energy from oceanic environments. However, due to the harsh conditions that these turbines operate in, system performance naturally degrades over time. Thus, ensuring efficient condition-based maintenance is imperative towards guaranteeing reliable operation and reduced costs for marine hydrokinetic power. This work proposes a novel framework aimed at identifying and classifying the severity of rotor blade pitch imbalance faults experienced by marine current turbines (MCTs). In the framework, a Continuous Morlet Wavelet Transform (CMWT) is first utilized to acquire the wavelet coefficients encompassed within the 1P frequency range of the turbine's rotor shaft. From these coefficients, several statistical indices are tabulated into a six-dimensional feature space. Next, Principle Component Analysis (PCA) is employed on the resulting feature space for dimensionality reduction, and then the application of a K-Nearest Neighbor (KNN) machine learning algorithm is utilized for fault detection and severity classification. The effectiveness of the proposed framework is validated using a high-fidelity MCT numerical simulation platform, where results demonstrate that the presence of a pitch imbalance fault can be accurately detected 100% of the time and correctly classified based upon severity more than 97% of the time.

42 ENGINEERING↗
DOE OSTI2024

Thermally generated magnonic spin currents in a polycrystalline gadolinium iron garnet thin film with perpendicular magnetic anisotropy

Rare-earth iron garnets (REIGs) are the benchmark systems for magnonics, including the longitudinal spin Seebeck effect (LSSE). While most research has focused on single-crystalline REIGs on complimentary garnet substrates, moving to more, cost-effective complementary metal-oxide semiconductor (CMOS)-compatible substrates is important to integrate REIG thin films with existing technology. In this regard, we grow a 130 nm-thick polycrystalline gadolinium iron garnet (GdIG) film on the Si/SiO2 substrate and investigate the temperature-dependent LSSE. Interestingly, the polycrystalline GdIG film exhibits perpendicular magnetic anisotropy (PMA) at room temperature which is induced by tensile in-plane (IP)-strain originating from the thermal-expansion mismatch between the GdIG film and the substrate during rapid thermal annealing. Further, a spin-reorientation transition from the out-of-plane IP direction below TS = 180 K is observed. Additionally, the film reveals a magnetic compensation temperature, TComp, of ≈240 K. The LSSE voltage not only demonstrates a sign-inversion around TComp, but also shows noticeable changes around TS. As compared to a single-crystalline GdIG film, the lower LSSE voltage for the polycrystalline GdIG is attributed to the higher effective magnetic anisotropy and enhanced magnon scattering at the grain boundaries. Our study not only paves the way for the cost-effective growth of CMOS-compatible REIG-based systems with PMA for magnonic memory and information processing applications, but also highlights the fact that the spincaloritronic and spin-insulatronic properties of the polycrystalline REIGs follow those of their single-crystalline counterparts with reduced spin-to-charge conversion efficiency through LSSE which can be tuned further by controlling the average gran size and interface engineering.

Physics↗
DOE OSTI2020

Methods and apparatus for making magnetic skyrmions

A system and a method for the deterministic generation of magnetic skyrmions includes a magnetic strip configured to store and transport skyrmions. The magnetic strip includes one or more spatial inhomogeneities configured to generate a skyrmion at known locations when excited by a current pulse. A current pulse generator is used to inject current pulses into the magnetic strip via contact pads electrically coupled to both the current pulse generator and the magnetic strip. The system also includes a magnetic field source to apply an out-of-plane magnetic field across the magnetic strip to facilitate generation of skyrmions. Skyrmions can be generated by applying an out-of-plane magnetic field to the magnetic strip and injecting a current pulse with sufficient current density towards the spatial inhomogeneities. Once a skyrmion is generated, another current pulse with sufficient current density can be injected to move the skyrmion.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2020

X-ray detection of ultrashort spin current pulses in synthetic antiferromagnets

Here, we explore the ultrafast generation of spin currents in magnetic multilayer samples by applying fs laser pulses to one layer and measuring the magnetic response in the other layer by element-resolved x-ray spectroscopy. In Ni(5 nm)/Ru(2 nm)/Fe(4 nm), the Ni and Fe magnetization directions couple antiferromagnetically due to the Ruderman–Kittel–Kasuya–Yosida interaction but may be oriented parallel through an applied magnetic field. After exciting the top Ni layer with a fs laser pulse, we also find that the Fe layer underneath demagnetizes, with a 4.1±1.9% amplitude difference between parallel and antiparallel orientation of the Ni and Fe magnetizations. We attribute this difference to the influence of a spin current generated by the fs laser pulse that transfers angular momentum from the Ni into the Fe layer. Our results confirm that superdiffusive spin transport plays a role in determining the sub-ps demagnetization dynamics of synthetic antiferromagnetic layers, but also evidence large depolarization effects due to hot electron dynamics, which are independent of the relative alignment of the magnetization in Ni and Fe.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Light-induced shift current vortex crystals in moiré heterobilayers

Transition metal dichalcogenide (TMD) moiré superlattices provide an emerging platform to explore various light-induced phenomena. Recently, the discoveries of novel moiré excitons have attracted great interest. The nonlinear optical responses of these systems are however still underexplored. Here, we report investigation of light-induced shift currents (a second-order response generating DC current from optical illumination) in the WSe 2 /WS 2 moiré superlattice. We identify a striking phenomenon of the formation of shift current vortex crystals—i.e., two-dimensional periodic arrays of moiré-scale current vortices and associated magnetic fields with remarkable intensity under laboratory laser setup. Furthermore, we demonstrate high optical tunability of these current vortices—their location, shape, chirality, and magnitude can be tuned by the frequency, polarization, and intensity of the incident light. Electron-hole interactions (excitonic effects) are found to play a crucial role in the generation and nature of the shift current intensity and distribution. Our findings provide a promising all-optical control route to manipulate nanoscale shift current density distributions and magnetic field patterns, as well as shed light on nonlinear optical responses in moiré quantum matter and their possible applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Observation of Vector Spin Seebeck Effect in a Noncollinear Antiferromagnet

Spintronic phenomena to date have been established in magnets with collinear moments, where the spin injection through the spin Seebeck effect (SSE) is always along the out-of-plane direction. Here, we report the observation of a vector SSE in a noncollinear antiferromagnet (AF) LuFeO 3 , where temperature gradient along the out-of-plane and also the in-plane directions can both inject a pure spin current and generate a voltage in the heavy metal via the inverse spin Hall effect (ISHE). We show that the thermovoltages are due to the magnetization from canted spins in LuFeO 3 . Furthermore, in contrast to the challenges of generating, manipulating, and detecting spin current in collinear AFs, the vector SSE in LuFeO 3 is readily viable in zero magnetic field and can be controlled by a small magnetic field of about 150 Oe at room temperature. Furthermore, the noncollinear AFs expand new realms for exploring spin phenomena and provide a new route to low-field antiferromagnetic spin caloritronics and magnonics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Magnets are Weber Bar Gravitational Wave Detectors

When a gravitational wave (GW) passes through a dc magnetic field, it couples to the conducting wires carrying the currents which generate the magnetic field, causing them to oscillate at the GW frequency. The oscillating currents then generate an ac component through which the GW can be detected-thus forming a resonant mass detector or a nagnetic Weber bar. We quantify this claim and demonstrate that magnets can have exceptional sensitivity to GWs over a frequency range demarcated by the mechanical and electromagnetic resonant frequencies of the system; indeed, we outline why a magnetic readout strategy can be considered an optimal Weber bar design. The concept is applicable to a broad class of magnets, but can be particularly well exploited by the powerful magnets being deployed in search of axion dark matter, for example, by DMRadio and ADMX-EFR. Explicitly, we demonstrate that the MRI magnet that is being deployed for ADMX-EFR can achieve a broadband GW strain sensitivity of ∼10^{-20}/sqrt[Hz] from a few kHz to about 10 MHz, with a peak sensitivity down to ∼10^{-22}/sqrt[Hz] at a kHz exploiting a mechanical resonance.

Domcke, Valerie↗
DOE OSTI2024

Photon Frequency Conversion in High-Q Superconducting Resonators: Axion Electrodynamics, QED, and Nonlinear Meissner Radiation

High-Q superconducting resonators have been proposed and developed as detectors of light-by-light scattering mediated by the hypothesized axion or virtual electron–positron pairs in quantum electrodynamics: the Euler–Heisenberg (EH) interaction. Photon frequency and mode conversion is central to the scheme for detecting such rare events. Superconducting resonators are nonlinear devices. The Meissner screening currents that confine the electromagnetic fields to the vacuum region of a superconducting RF cavity are nonlinear functions of the EM field at the vacuum–superconducting interface, and as a result can generate source currents and frequency conversion of microwave photons in the cavity. In this report we consider photon frequency and mode conversion in superconducting resonators with high quality factors from Meissner currents in single- and dual-cavity setups proposed for axion and QED searches based on light-by-light scattering. In a single cavity with two pump modes, photon frequency conversion by the Meissner screening current dominates photon generation by the EH interaction for cavities with Q≲1012⁠. The Meissner currents also generate background photons that limit the operation of the resonator for axion detection in three-mode, single-cavity setups. We also consider the leakage of photons from pump modes into the signal mode for both axion- and EH-mediated light-by-light scattering. Photon frequency conversion by the EH interaction can compete with Meissner and leakage radiation in ultra-high-Q cavities that are beyond the current state of the art. Meissner radiation and leakage backgrounds can be suppressed in dual-cavity setups with appropriate choices for pump and spectator modes, as well as the single-cavity setup proposed for heterodyne detection of galactic axion dark matter.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2020

National Spherical Torus eXperiment - Upgrade NSTX-U: Structural Analysis of Passive Plates Support Brackets

The objective of this analysis is to estimate and assess the stresses in the passive plates caused by a limiting plasma disruption. The objective of this calculation is also to address observed damage to mounting hardware after completion of NSTX operation. These observations initiated diagnostic efforts during the Upgrade project to monitor the severity of the disruptions that were causing the damage, and planned instrumentation to trend the behavior of the mounting hardware. The Recovery Project mission for the passive plate hardware is to appropriately reinforce the passive plates with stainless steel ribs mounted on the back of the plate to reduce their flexure and stress and reinforcements of the “biscuit” components of the bracketry to transfer loads without damage to bolts, biscuits, and bracket plates and welds. Mid-plane disruptions and quenches were manageable with NSTX vintage hardware. The Vertical Displacement Event (VDE) disruptions position the plasma closer to the passive plates and are more severe than the centered plasma. Earlier work pointed to the P1-P5 VDE as limiting. This has been confirmed by A. Brooks work in support of the load generation effort in reference. During vertical displacement large counter currents are generated in the plate as the plasma approaches it. - as would be expected from passive plates. When the plasma disrupts the currents in the plates are reversed, which also reverses the loading on the plates. This report documents the methodology and results of transient structural analysis on the plasma, passive plates support brackets. The loads induced by eddy and halo currents have been considered, and were generated using a separate electromagnetic analysis (NSTXU_1_11_2_1_CALC_051). The structural model also incorporates the effects from preload. Calculation was performed with the assumption that existing biscuits are not participating in the load bearing except the biscuits connected to jumper bolts, which are fully engaged. Results show that with the planned reinforcements, Passive plates and mounting structures satisfy static and fatigue criteria in all areas except welds, where separate analysis was performed. Both symmetric and asymmetric (with locating block) designs were analyzed, and although stresses were higher without locating block they still satisfy NSTX design criteria.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗