SEARCH · Engineering Papers

Results for “conduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

All sources NASA NTRS DOE OSTI

NASA NTRSDate not supplied

Using Holey Graphene for Improved Interfacial Contact in Solid Electrolyte Ionic Conductivity Measurements

Solid-state batteries (SSBs) are poised to become the batteries of the future with advantages such as higher energy density, lighter weight, versatile geometry, and greater safety due to low flammability risk. An important parameter of the solid electrolyte (SE) used is its ionic conductivity. The ionic conductivity is generally calculated from the bulk resistance of a SE pellet, measured from the electrochemical impedance spectroscopy data. The SE pellet is typically prepared from the electrolyte powder by dry compression and is sandwiched between two blocking current collectors to obtain the impedance spectroscopy data. One of the challenges in conducting this measurement is poor interfacial contacts between the SE pellet and the current collector surfaces. Therefore, measurements reported in the literature may underestimate the true ionic conductivity of a given electrolyte. Holey graphene is a carbon nanomaterial with high electrical conductivity and unique dry compressibility, which is unusual for carbon materials but similar to many oxide and sulfide SEs. In this work, it is demonstrated that adding a thin layer of holey graphene between the electrolyte and the stainless steel current collectors significantly improves the interfacial contact. The ionic conductivity values obtained in the effort were sometimes several times higher than the data measured for SEs without the holey graphene layers. This work calls for more standardized measurement procedures to reduce the discrepancies in reported ionic conductivity values.

Solid state battery↗

NASA NTRS2024

The Global Mapping of Electron Precipitation and Ionospheric Conductance From Whistler-Mode Chorus Waves

Auroral precipitation is the second major energy source after solar irradiation that ionizes the Earth’s upper atmosphere. Diffuse electron aurora caused by wave-particle interaction in the inner magnetosphere (L < 8) takes over 60% of total auroral energy flux, strongly contributing to the ionospheric conductance and thus to the ionosphere-thermosphere dynamics. This paper quantifies the impact of chorus waves on the diffuse aurora and the ionospheric conductance during quiet, medium, and strong geomagnetic activities, parameterized by AE <100, 100 < AE < 300, and AE > 300, respectively. Using chorus wave statistics and inner-magnetosphere plasma conditions from Timed History Events and Macroscale Interactions during Substorms (THEMIS) observations, we directly derive the energy spectrum of diffuse electron precipitation under quasi-linear theory. We then calculate the height-integrated conductance from the wave-driven aurora spectrum using the electron impact ionization model of Fang et al. (Geophys. Res. Lett., 2010, 37) and the MSIS atmosphere model. By utilizing Fang’s ionization model, the US Naval Research Laboratory Mass Spectrometer and Incoherent Scattar Radar (NRLMSISE-00) model from 2000s for the neutral atmosphere components, and the University of California, Los Angeles (UCLA) Full Diffusion Code, we improve upon the standard generalization of Maxwellian diffuse electron precipitation patterns and their resulting ionosphere conductance. Our study of global auroral precipitation and ionospheric conductance from chorus wave statistics is the first statistical model of its kind. We show that the total electron flux and conductance pattern from our results agree with those of Ovation Prime model over the pre-midnight to post-dawn sector as geomagnetic activity increases. Our study examines the relative contributions of upper band chorus (UBC) and lower band chorus wave (LBC) driven conductance in the ionosphere. We found LBC waves drove diffuse electron precipitation significantly more than UBC waves, however it is possible that THEMIS data may have underestimated the upper chorus band wave observations for magnetic latitudes below 65 degrees. ° .

diffuse auroral precipitation↗

DOE OSTI2025

Mechanism of Contrasting Ionic Conductivities in Li 2 ZrCl 6 via I and Br Substitution

Understanding the complex structural and chemical factors that influence ionic conduction mechanisms is paramount for developing advanced inorganic superionic conductors in all‐solid‐state batteries, particularly halide solid electrolytes with excellent electrochemical oxidative stability and mechanical sinterability. Herein, contrasting ionic conduction behaviors in I − and Br − substituted Li 2 ZrCl 6 are revealed by combining experimental structural analyses and theoretical calculations. The inter‐slab distance along the c ‐axis, which varies with the anion substitution and M2‐M3 site disorder, is a key factor for opening the ab ‐plane conduction and facilitating the overall Li + conduction. Increased M3 site occupancy generally leads to contracted inter‐slab distance. The substantial increase in Li + conductivity upon I substitution (from 0.40 to 0.91 mS cm −1 ) originates from a sufficiently expanded lattice volume owing to its large ionic radii (I − = 2.20 Å), particularly inter‐slab distance that facilitates the ab intra‐plane Li + conduction, which also benefits from decreased M2‐M3 disorder. In contrast, Br (Br − = 1.96 Å) substitution results in insufficiently expanded Li + channels, which, exacerbated by increased M2‐M3 disorder, leads to degradation in Li + conductivity. Implementing I − substituted Li 2 ZrCl 6 resulted in superior electrochemical performance in LiCoO 2 ||Li‐In cells compared to those with an unsubstituted catholyte.

36 MATERIALS SCIENCE↗

DOE OSTI2022

A Finite Difference Analysis of the Effect of Graphene Additions on the Electrical Conductivity of Polycrystalline Copper

A finite-difference method was used to explore the effect of graphene on the bulk electrical conductivity of copper-graphene composites. In this capacity, grain orientation information from pure copper and copper-graphene composites were used to generate synthetic 3D microstructures. The electrical conductivity of these microstructures were calculated using the finite difference method assuming different average grain sizes. From these calculations, we demonstrate that when high-conductivity grain boundaries are present within the microstructure arising from the presence of graphene, an increase in the bulk electrical conductivity is observed. On the other hand, the difference in textures between copper and copper-graphene composites may not account for a significant difference in bulk electrical conductivity. In comparison, the copper grain size has a considerably larger effect on electrical conductivity as previously anticipated. This is one of the first demonstrations of a physical basis for enhanced conductivity composites and presents pathways for further investigations on the effects of composite microstructural features, material interfaces and graphene content on electrical performance.

Frazier, William E.↗

DOE OSTI2026

A Cheeger inequality for size-specific conductance

The μ-conductance measure proposed by Lovász and Simonovits is a size-specific conductance score that identifies the set with smallest conductance while disregarding those sets with volume smaller than a μ fraction of the whole graph. Using μ-conductance enables us to study the network structures in new ways. Here, in this manuscript, we study a modified spectral cut for μ-conductance that is a natural relaxation of the integer program of μ-conductance and show that the optimum of this program has a two-sided Cheeger inequality with μ-conductance.

Graph theory↗

DOE OSTI2020

Extrapolation of thermal conductivity in non-equilibrium molecular dynamics simulations to bulk scale

Predictions of the bulk scale thermal conductivity of solids using non-equilibrium molecular dynamics (MD) simulations have relied on the linear extrapolation of the thermal resistivity versus the reciprocal of the system length in the simulations. Several studies have reported deviation of the extrapolation from linearity near the micro-scale, raising a concern of its applicability to large systems. To investigate this issue, present work conducted extensive MD simulations of silicon with two different potentials (EDIP and Tersoff-II) for unprecedented length scales up to 10.3 μm and simulation times up to 530 ns. For large systems ≥0.35 μm in size the non-linearity of the extrapolation of the reciprocal of the thermal conductivity is mostly due to ignoring the dependence of the thermal conductivity on temperature. To account for such dependence, the present analysis fixes the temperature range for determining the gradient for calculating the thermal conductivity values. However, short systems ≤0.23 μm in size show significant non-linearity in the calculated thermal conductivity values using a temperature window of 500 ± 10 K from the simulations results with the EDIP potential. Since these system sizes are shorter than the mean phonon free path in EDIP (~0.22 μm), the nonlinearity may be attributed to phonon transport. For the MD simulations with the Tersoff-II potential there is no significant non-linearity in the calculated thermal conductivity values for systems ranging in size from 0.05 to 5.4 μm.

42 ENGINEERING↗

DOE OSTI2024

Alternating conduction and convection drying of paper – an experimental analysis with a continuous data acquisition approach

In conventional multi-cylinder drying of paper and board, both conductive drying from steam-heated dryer cylinders and convective drying by flowing air over the paper surface in the pockets are used. Conductive drying from steam-heated drying cylinders is a critical component in providing the necessary thermal energy to paper and board as they dry. Steam temperature and internal and external resistances at the contacting surface are critical process parameters influencing the conductive drying process. An experimental setup was developed to study the alternating conductive and convective drying of paper and board. Paper sheet moisture, temperature, and temperature distribution within the heated platen and the instantaneous heat flux as the sheet was being dried were measured. The instantaneous heat flux, contact heat transfer coefficient, and drying rates were determined as drying proceeds. Experimental results, as well as comparisons to literature and commercial data, are presented. The conductive heat transfer coefficients determined were compared to traditional correlations normally used in the modeling of paper drying. Similarly, the convective heat and mass transfer coefficients are also determined and compared to literature data. In addition to the evaluation of alternating conductive and convective drying characteristics of paper and board, the potential inclusion of auxiliary energy components will also be included. Experimental results from the conduction and convection drying system are presented. Furthermore, this data will be useful in process development, intensification of manufacturing processes, and modeling and simulation of paper drying processes.

42 ENGINEERING↗

DOE OSTI2025

Critical role of polymer-ceramic ion exchange for high conductivity composite electrolytes

Polymer-ceramic composites offer a path to enhance the transport and mechanical properties of solid electrolytes. However, an in-depth understanding of the extent and role of ion transport along and across polymer-ceramic interfaces in these systems is lacking. We have recently shown that Li-conducting Li 0.11 Na 0.24 K 0.02 La 0.43 TiO 2.82 (LMTO) nanorods can be prepared by a molten flux method, and the addition of 30–50 weight (wt.)% LMTO to a bis[(trifluoromethyl)sulfonyl]imide-vinyl ethylene carbonate-based single-ion conducting (SIC) polymer electrolyte leads to a two-fold enhancement in Li-ion conductivity, from 1.4 to 3.0 × 10 −5 S/cm at 30 °C. In the present study, we use NMR methods to identify the Li-ion transport pathways and determine the timescale of chemical exchange between the SIC polymer and LMTO ceramic components. Tracer exchange NMR indicates preferential transport through the polymer or polymer-interfacial regions, and exchange spectroscopy (EXSY) and a new isotope exchange method reveal negligible Li exchange between the SIC polymer and LMTO ceramic up to several days. Here, LMTO nanorods act as a passive filler. Our results further highlight that significant (e.g., 10- or 100-fold) conductivity enhancements in composite electrolytes can only be achieved 1) with ionically-conductive fillers, and 2) when both the ceramic and polymer components actively participate in long-range transport. For this, fast interfacial ion exchange is needed. In conclusion, this leads us to introduce a critical interfacial ion exchange time to evaluate whether a filler actively contributes to conduction in a composite electrolyte, and screen for promising polymer-ceramic pairings to accelerate the development of high conductivity solid electrolytes.

Battery, Solid electrolyte↗

DOE OSTI2021

Signatures of Coherent Phonon Transport in Ultralow Thermal Conductivity Two-Dimensional Ruddlesden–Popper Phase Perovskites

An emerging class of methylammonium lead iodide (MAPbI 3 )-based Ruddlesden-Popper (RP) phase perovskites, BA 2 MA n-1 Pb n I 3n+1 (n = 1-7), exhibit enhanced stability to environmental conditions relative to MAPbI 3 , yet still degrade at elevated temperatures. Here, we experimentally determine the thermal conductivities of these layered RP phases for n = 1-6, where n defines the number of repeated perovskite octahedra per layer. We measure thermal conductivities of 0.37 ± 0.13/0.12, 0.17 ± 0.08/0.07, 0.21 ± 0.05/0.04, and 0.19 ± 0.04/0.03 W/m∙K in thin films of n = 1-4 and 0.08 ± 0.06/0.04, 0.06 ± 0.04/0.03, 0.06 ± 0.03/0.03, and 0.08 ± 0.07/0.04 W/m∙K in single crystals of n = 3-6. With the exception of n = 1, these thermal conductivities are lower than the range of 0.34-0.50 W/m∙K reported for single-crystal MAPbI 3 . Reduced-order lattice dynamics modeling suggests that the initially decreasing trend of thermal conductivity in similarly oriented perovskites with increasing n may result from the transport properties of coherent phonons, emergent from the superstructure, that do not scatter at the interfaces of organic butylammonium chains and perovskite octahedra. Reduced group velocity of coherent phonons in n = 3-6, a consequence of band flattening in the phonon dispersion, is primarily responsible for their ultralow thermal conductivities. Similar effects on thermal conductivity have been experimentally demonstrated in deposited superlattices, but never in naturally defined materials such as RP phases. GIWAXS measurements reveal that higher n RP phase thin films are less orientationally controlled and therefore possess apparently elevated thermal conductivities relative to single crystals of the same n.

2D perovskites↗

DOE OSTI2020

Characterizing Physical Properties of Streambed Interface Sediments Using In Situ Complex Electrical Conductivity Measurements

Streambed sediment physical properties such as surface area, are difficult to quantify in situ but exert a high-level control on a wide range of biogeochemical processes and sorption of contaminants. We introduce the use of complex electrical conductivity (CC) methods (also known as spectral-induced polarization (SIP)) that measure both real and imaginary conductivity to noninvasively and efficiently characterize shallow streambed sediments. We explore the method through synthetic modeling, laboratory, and field measurements to demonstrate the sensitivity of imaginary conductivity to sediment surface area, controlled in part by fine-grained iron oxides produced by anoxic groundwater discharge. Laboratory measurements verify expected relationships between CC parameters and sediment properties. Synthetic modeling using a 1D analytical model illustrates the influence of water layer depth and conductivity on the field CC measurements made at the streambed-stream water interface. Specifically, the inverted sediment imaginary conductivity is less impacted by uncertainty in the water layer depth and conductivity relative to the real conductivity and phase shift. Field CC measurements along a landfill-impacted river reveal discrete streambed zones with enhanced bulk surface area generally corresponding to anoxic groundwater discharge zones with high concentrations of fine-grained iron oxide precipitates.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2021

Intrinsic nanostructure induced ultralow thermal conductivity yields enhanced thermoelectric performance in Zintl phase Eu2ZnSb2

Abstract The Zintl thermoelectric phase Eu 2 ZnSb 2 has a remarkable combination of high mobility and low thermal conductivity that leads to good thermoelectric performance. The key feature of this compound is a crystal structure that has a Zn-site with a 50% occupancy. Here we use comparison of experimental thermal conductivity measurements and first principles thermal conductivity calculations to characterize the thermal conductivity reduction. We find that partial ordering, characterized by local order, but Zn-site disorder on longer scales, leads to an intrinsic nanostructuring induced reduction in thermal conductivity, while retaining electron mobility. This provides a direction for identifying Zintl compounds with ultralow lattice thermal conductivity and good electrical conductivity.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Reversible two-way tuning of thermal conductivity in an end-linked star-shaped thermoset

Polymeric thermal switches that can reversibly tune and significantly enhance their thermal conductivities are desirable for diverse applications in electronics, aerospace, automotives, and medicine; however, they are rarely achieved. Here, we report a polymer-based thermal switch consisting of an end-linked star-shaped thermoset with two independent thermal conductivity tuning mechanisms—strain and temperature modulation—that rapidly, reversibly, and cyclically modulate thermal conductivity. The end-linked star-shaped thermoset exhibits a strain-modulated thermal conductivity enhancement up to 11.5 at a fixed temperature of 60 °C (increasing from 0.15 to 2.1 W m –1 K –1 ). Additionally, it demonstrates a temperature-modulated thermal conductivity tuning ratio up to 2.3 at a fixed stretch of 2.5 (increasing from 0.17 to 0.39 W m –1 K –1 ). When combined, these two effects collectively enable the end-linked star-shaped thermoset to achieve a thermal conductivity tuning ratio up to 14.2. Moreover, the end-linked star-shaped thermoset demonstrates reversible tuning for over 1000 cycles. The reversible two-way tuning of thermal conductivity is attributed to the synergy of aligned amorphous chains, oriented crystalline domains, and increased crystallinity by elastically deforming the end-linked star-shaped thermoset.

42 ENGINEERING↗

DOE OSTI2021

A negative piezo-conductive effect from doped semiconducting polymer thin films

In the past years, piezo-conductive sensors have drawn great attention in both academic and industrial sectors. The piezo-conductive sensors made by inorganic semiconductors exhibited poor mechanical flexibility, restricting their further practical applications. In this study, we report the piezo-conductive sensors by a semiconducting polymer, poly(3,4-ethylenedioxythiophene) doped with tosylate ions (PEDOT:Tos) thin films. Systemically studies indicate that the piezo-conductive response of the PEDOT:Tos thin films is originated from the deformation of the PEDOT crystal cells and the stretched π–π distances induced by Tos. Moreover, the negative piezo-conductive effect, for the first time, is observed from PEDOT:Tos thin film under the pressure. A working mechanism is further proposed to interpret the transient from a positive to a negative piezo-conductive response within the PEDOT:Tos thin films. Our studies offer a facile route to approach effective piezo-conductive sensors based on conjugated polymers.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Conductivity and size quantization effects in semiconductor $$\delta$$-layer systems

Abstract We present an open-system quantum-mechanical 3D real-space study of the conduction band structure and conductive properties of two semiconductor systems, interesting for their beyond-Moore and quantum computing applications: phosphorus $$\delta$$ δ -layers and P $$\delta$$ δ -layer tunnel junctions in silicon. In order to evaluate size quantization effects on the conductivity, we consider two principal cases: nanoscale finite-width structures, used in transistors, and infinitely-wide structures, electrical properties of which are typically known experimentally. For devices widths $$W<10$$ W < 10 nm, quantization effects are strong and it is shown that the number of propagating modes determines not only the conductivity, but the distinctive spatial distribution of the current-carrying electron states. For $$W>10$$ W > 10 nm, the quantization effects practically vanish and the conductivity tends to the infinitely-wide device values. For tunnel junctions, two distinct conductivity regimes are predicted due to the strong conduction band quantization.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Mechanically robust and superior conductive n-type polymer binders for high-performance micro-silicon anodes in lithium-ion batteries

Compared with nanostructured silicon (Si), the Si microparticle (SiMP) has more commercial prospects due to its low cost. However, SiMPs suffer from unavoidable fracture during electrochemical cycling owing to their significant volume change. Here we develop a series of novel n-type conductive polymer binders (CPBs) for SiMP anodes in lithium-ion batteries owing to their superior properties. Extraordinary electrochemical performance of cells with such unique binders could be achieved, which is because these designed polymers contain electron-withdrawing oxadiazole ring groups and easily ionizable sulfonate polar groups, exhibiting excellent ionic conductivity, outstanding wettability to the electrolyte, and improved electronic conductivity after doping. Moreover, the coexistence of rigid and flexible chains enables them to have exceptional strength and ductility. Besides, a unique electrochromic approach has been utilized to investigate the energy gap of the CPBs in n-doping states. The ionic and electronic conductivities of prepared CPBs in an eigenstate and n-doping state have been systematically studied by the electrochemical method, filling the current research gap in this field. Due to the high conductivity of b-POD, the capacity of SiMPs (4200 mA h g –1 ) can be almost entirely released during the first cycle of discharge, while the SiMP anodes prepared with the PAALi or CMC binder show a much lower initial capacity. Here, the high conductivity of b-POD also endows it with better cycling performance than non-conductive binders especially at high current densities, demonstrating its excellent fast-charging ability. More essentially, this work provides polymer binders without any intricate structural designs to obtain high-performance SiMP batteries, significantly enhancing their practical applications.

25 ENERGY STORAGE↗

DOE OSTI2024

Effects of Al concentration on the structure and conductivity of lithium lanthanum zirconium oxide

Cubic Li 7-3x Al x La 3 Zr 2 O 12 (LLZO) is a promising, next-generation solid electrolyte due to its stability with Li-metal and high bulk conductivity (~1 mS cm -1 ). However, the source of the high conductivity is not completely understood. In this work, we address this key knowledge gap through the integration of elemental analysis, neutron diffraction sensitive to Li and O atoms, and impedance spectroscopy to understand the structure–property correlations for LLZO. We show the metal–oxygen framework structure remains constant with variation in Al substitution, resulting in a constant activation energy of ~0.35 eV and little effect on the bulk conductivity. Instead, Li concentration, Al blocking and trapping of mobile defects, and Li–Li nearest neighbor interactions largely control the Al substituted LLZO bulk conductivity, resulting in decreases from 0.73 to 0.22 mS cm -1 as the Al concentration increases from 0.17 to 0.32 mol. These results differ from those of Ta substituted LLZO, where the framework structure and Li–Li site distances play large roles in controlling the conductivity. The increased understanding of the controlling factors of conductivity allows for greater ability to tailor the design of and substitution into the LLZO structure for improved conductivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Effect of surface functional groups on MXene conductivity

In this work, we report the in-plane electron transport in the MXenes (i.e., within the MXene layers) as a function of composition using the density-functional tight-binding method, in conjunction with the non-equilibrium Green’s functions technique. Our study reveals that all MXene compositions have a linear relationship between current and voltage at lower potentials, indicating their metallic character. However, the magnitude of the current at a given voltage (conductivity) has different trends among different compositions. For example, MXenes without any surface terminations (Ti 3 C 2 ) exhibit higher conductivity compared to MXenes with surface functionalization. Among the MXenes with –O and –OH termination, those with –O surface termination have lower conductivity than the ones with –OH surface terminations. Interestingly, conductivity changes with the ratio of –O and –OH on the MXene surface. Our calculated I–V curves and their conductivities correlate well with transmission functions and the electronic density of states around the Fermi level. The surface composition-dependent conductivity of the MXenes provides a path to tune the in-plane conductivity for enhanced pseudocapacitive performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Phonon Olympics: Phonon property and lattice thermal conductivity benchmarking from open-source packages

Three widely used open-source packages for determining phonon properties and lattice thermal conductivities (ALAMODE, phono3py, and ShengBTE) are benchmarked by teams of expert users and the package developers. The phonons for Ge, RbBr, monolayer MoSe 2 , and AlN are modeled at zero temperature, and they scatter through three-phonon and phonon-isotope processes, with thermal conductivities obtained from the linearized Peierls–Boltzmann transport equation with input from density functional theory calculations. Over a wide range of temperatures, the thermal conductivities calculated by the teams fall within at most ±15% of their mean values for each of the four materials. The phonon frequencies, obtained from the harmonic force constants, do not show large differences between the calculations, indicating that the modal heat capacities and group velocities are not responsible for the thermal conductivity variations. It is the lifetimes associated with three-phonon scattering, obtained from the cubic force constants, that drive the variations. The many decisions required to calculate the cubic force constants (e.g., supercell size, atomic displacement, neighbor cutoff, and application of symmetries) make identification of the precise origin of the thermal conductivity variations challenging. The calculated thermal conductivities do not generally show agreement with experimental measurements, which is attributed to the limitations of the density functional theory calculations. Guidance for the development of best practices is provided, which will help to standardize protocols needed for building thermal conductivity databases. The results provide a baseline for future benchmarking of other packages and more advanced calculations.

McGaughey, Alan J. H. [Carnegie Mellon Univ., Pitt↗