Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “conditional expectations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Ion Exchange Temperature Testing with SRF Resin - 12088

Ion exchange using the Spherical Resorcinol-Formaldehyde (SRF) resin has been selected by the U.S. Department of Energy's Office of River Protection for use in the Pretreatment Facility of the Hanford Tank Waste Treatment and Immobilization Plant (WTP) and for potential application in an at-tank deployment for removing Cs-137. Recent proposed changes to the WTP ion exchange process baseline indicate that higher temperatures (50 deg. C) to alleviate post-filtration precipitation issues prior to reaching the ion exchange columns may be required. Therefore, it is important to understand the behavior of SRF resin performance under the conditions expected with the new equipment and process changes. This research examined the impact of elevated temperature on resin loading and resin degradation during extended solution flow at elevated temperature (45 deg., 50 deg., 55 deg., 60 deg., 65 deg., 75 deg. C). Testing for extended times at elevated temperatures showed that the resin does degrade and loading capacity is reduced at and above 45 deg. C. Above 60 deg. C the resin appears to not load at all. It was observed that the resin disintegrated at 75 deg. C until not much was left and partially disintegrated at 65 deg. C, which caused the column to plug in both tests after ∼336 hours. The results indicate that WTP will lose resin loading capacity if the ion exchange process is performed above 25 deg. C, and the resin will disintegrate above 65 deg. C. Therefore, WTP will have a restricted operating range of temperatures to perform the ion exchange process with this resin. PNNL and WTP are currently evaluating the operating limits of the resin in further detail. Aging in 0.5 M HNO{sub 3} also caused the resin to lose capacity above 25 deg. C and to completely dissolve at 55 deg. C. Again, WTP will have a restricted operating range of temperatures when eluting the resin with nitric acid in order to maintain resin loading capacity and avoid disintegration of the resin. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Effects of Gamma Radiation on Cementitious Materials in Repository Environment - 16300

Cementitious materials are widely used in the management of radioactive waste and have to perform as required for the period of service life of the installation. In order to assess the long term durability of cement paste in a deep borehole for radioactive wastes, specimens were cast in laboratory and exposed to a gamma radiation field. The effects of the radiation in the specimens were evaluated by X-Ray Diffraction, as changes observed in the mineralogy and microstructure of the material after irradiation doses varying between 0 (without radiation) and 10 MGy. It was observed that the specimens exposed to higher doses of gamma radiation (up to 3 MGy) presented differences between surface and core, when compared with the samples with no radiation or exposed to low doses. These results are important to model the behavior of cementitious materials under the conditions expected in a borehole repository and to provide data for the safety assessment of the installation. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Optimizing Short-Term Operation of a FIRES-like Industrial Heat Supply Thermal Energy Storage System

The Firebrick Resistance-heated Energy-storage System (FIRES) is under development at MIT for two applications: (1) integration with the Nuclear Air-Brayton Combined Cycle (NACC), a high-performance power conversion system (PCS) that may be used with high- temperature advanced reactors; and (2) industrial heat supply. This paper describes some key features of FIRES and equivalent systems configured for industrial heat supply and presents an assessment of the revenue achievable by a system operating under the conditions expected for early demonstration FIRES installations. The greatest technical challenge of the 21. century is likely to be the effort to minimize the damage caused by global climate change. This effort will require massive reductions in greenhouse gas (GHG) emissions throughout our economy and a transition to an electric power system driven entirely by very-low-carbon generators. Many investigators agree that this will require a substantial increase in electricity generation and in the use of nuclear power, and there is growing awareness that this will also require new technologies and systems for managing and storing energy and matching intermittent supply of renewable resources with electricity demand. Thermal energy storage systems (TESS) will, in some applications, be much more cost effective than the more popular and widely discussed battery electric storage systems and may provide unique capabilities. The Firebrick Resistance-heated Energy-storage System (FIRES) is under development at MIT for two applications: (1) integration with the Nuclear Air-Brayton Combined Cycle (NACC), a high-performance power conversion system (PCS) that may be used with high-temperature advanced reactors like the Fluoride-salt-cooled High-temperature Reactor (FHR), molten salt reactor (MSR) and sodium-cooled fast reactors (SFR); and (2) industrial heat supply. FIRES installations include a stack of refractory firebrick with imbedded electric heaters and airflow channels, a compressor or air blower, and a duct system to connect the firebrick with the heat demand (turbine or industrial customer). Analysis of the FIRES design space has shown that the concept is suitable for a wide range of peak operating temperatures (from about 200 deg.C up to at least 1800 deg. C) and pressures (from ambient to at least 20 atmospheres) and offers very high energy density (up to 1 MWh per cubic meter of firebrick for high temperature systems) at very low cost (as low as $5/kWh). These results favor early demonstration of FIRES. If the cost target of $5/kWh for FIRES systems were achieved, even the lowest expected operating income calculated here could cover the capital cost of a 10 MWh system in a single year. If the FIRES system were assumed to operate for at least 10 years, this level of operating income could readily recover a capital investment up to $50/kWh, which is simultaneously much cheaper than the costs expected for near-future battery systems (in excess of $200/kWh) and much more expensive than the small, low temperature firebrick systems already available for domestic heating. This provides a large margin for unexpected development costs and other uncertainties. FIRES would set a minimum price of electricity near that of natural gas-improving nuclear, wind, and solar economics while reducing greenhouse gas emissions from the industrial sector. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Overview of LWR Accident Tolerant Fuel Development in the United States

The U.S. Department of Energy (DOE) has conducted research and development (R and D) for enhanced, accident tolerant fuels (ATF) for light water reactors (LWRs) since 2012. The recently released Road-map to Congress for 'Development of Light Water Reactor Fuels with Enhanced Accident Tolerance' establishes the attributes that are desired for fuels that will exhibit enhanced accident tolerance and defines a path forward for the necessary R and D activities that will result in a lead fuel rod (LFR) or assembly (LFA) insertion in an operating, commercial LWR by 2022 to demonstrate the possibility of these advanced technologies. The aggressive development timeline is directed by Congressional language in the Senate Appropriations Committee Report (Senate Report 112-75), included in the Fiscal Year (FY) 2012 Energy and Water Development Appropriations Bill. ATF development is intended to be impactful to the current fleet of LWRs and future Generation III+ reactors. The development, future licensing and utility adoption of ATF technology will empower development of advanced technologies with safety significance. The work has progressed significantly since 2012, with multiple fuel and cladding concepts currently undergoing fundamental R and D including in-pile irradiation and out-of-pile testing to measure fundamental properties and to demonstrate performance under expected conditions. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

ibr: Iterative bias reduction multivariate smoothing

Regression is a fundamental data analysis tool for relating a univariate response variable Y to a multivariate predictor X {element_of} E R{sup d} from the observations (X{sub i}, Y{sub i}), i = 1,...,n. Traditional nonparametric regression use the assumption that the regression function varies smoothly in the independent variable x to locally estimate the conditional expectation m(x) = E[Y|X = x]. The resulting vector of predicted values {cflx Y}{sub i} at the observed covariates X{sub i} is called a regression smoother, or simply a smoother, because the predicted values {cflx Y}{sub i} are less variable than the original observations Y{sub i}. Linear smoothers are linear in the response variable Y and are operationally written as {cflx m} = X{sub {lambda}}Y, where S{sub {lambda}} is a n x n smoothing matrix. The smoothing matrix S{sub {lambda}} typically depends on a tuning parameter which we denote by {lambda}, and that governs the tradeoff between the smoothness of the estimate and the goodness-of-fit of the smoother to the data by controlling the effective size of the local neighborhood over which the responses are averaged. We parameterize the smoothing matrix such that large values of {lambda} are associated to smoothers that averages over larger neighborhood and produce very smooth curves, while small {lambda} are associated to smoothers that average over smaller neighborhood to produce a more wiggly curve that wants to interpolate the data. The parameter {lambda} is the bandwidth for kernel smoother, the span size for running-mean smoother, bin smoother, and the penalty factor {lambda} for spline smoother.

97 MATHEMATICS AND COMPUTING↗

Controls on Incomplete Mixing of Injected Raw Water and Brine in Strategic Petroleum Reserve Salt Caverns

Mixing of injected raw (undersaturated) water with brine in Strategic Petroleum Reserve (SPR) salt caverns affects the shape of cavern walls due to leaching. Cavern shape impacts cavern geomechanical stability and available volume for oil storage. Raw water injection occurs during initial solution mining of caverns, remedial leaching of caverns, and oil drawdown. Of interest are factors that control the degree of raw water-brine mixing and thereby the concentration of the aqueous fluid mixture that contacts the salt cavern walls. It is hypothesized that poorly-mixed fresh water could potentially cause undesirable and non-uniform leaching , for example, if buoyant poorly-mixed fresh water collects and preferentially leaches under the oil-brine interface . This report presents current understanding of controls on incomplete-to-complete mixing of raw water and brine, focusing on implications for SPR cavern leaching. In the context of mixing, we review the following: SPR leaching operations; models of leaching; field measurements of leaching and cavern shapes; and previous laboratory experiments of mixing and /or leaching performed at Sandia National Laboratories. We present recent laboratory experiments in 2014-2016 that focused explicitly on understanding controls of poor-to-well mixed conditions. We find that well-mixed conditions are expected for typical operating conditions of the SPR.

04 OIL SHALES AND TAR SANDS↗

Implementing Recommendations of the Columbia Accident Investigation Board - Development of on-Orbit RCC Thermography

One of NASA s Space Shuttle Return-to-Flight (RTF) efforts has been to develop thermography for the on-orbit inspection of the Reinforced Carbon Carbon (RCC) portion of the Orbiter Wing Leading Edge (WLE). This paper addresses the capability of thermography to detect cracks in RCC by using in-plane thermal gradients that naturally occur on-orbit. Crack damage, which can result from launch debris impact, is a detection challenge for other on-orbit sensors under consideration for RTF, such as the Intensified Television Camera and Laser Dynamic Range Imager. We studied various cracks in RCC, both natural and simulated, along with material characteristics, such as emissivity uniformity, in steady-state thermography. Severity of crack, such as those likely and unlikely to cause burn through were tested, both in-air and in-vacuum, and the goal of this procedure was to assure crew and vehicle safety during re-entry by identification and quantification of a damage condition while on-orbit. Expected thermal conditions are presented in typical shuttle orbits, and the expected damage signatures for each scenario are presented. Finally, through statistical signal detection, our results show that even at very low in-plane thermal gradients, we are able to detect damage at or below the threshold for fatality in the most critical sections of the WLE, with a confidence exceeding 1 in 10,000 probability of false negative.

Ottens, Brian↗

Implementing Recommendations of the Columbia Accident Investigation Board: Development of On-Orbit IR Thermography

One of NASA's Space Shuttle Return-to-Flight (RTF) efforts has been to develop thermography for the on-orbit inspection of the Reinforced Carbon Carbon (RCC) portion of the Orbiter Wing Leading Edge (WLE). This paper addresses the capability of thermography to detect cracks in RCC by using in-plane thermal gradients that naturally occur on-orbit. Crack damage, which can result from launch debris impact, is a detection challenge for other on-orbit sensors under consideration for RTF, such as the Intensified Television Camera and Laser Dynamic Range Imager. We studied various cracks in RCC, both natural and simulated, along with material characteristics, such as emissivity uniformity, in steady-state thermography. Severity of crack, such as those likely and unlikely to cause burn through were tested, both in-air and in-vacuum, and the goal of this procedure was to assure crew and vehicle safety during reentry by identification and quantification of a damage condition while on-orbit. Expected thermal conditions are presented in typical shuttle orbits, and the expected damage signatures for each scenario are presented. Finally, through statistical signal detection, our results show that even at very low in-plane thermal gradients, we are able to detect damage at or below the threshold for fatality in the most critical sections of the WLE, with a confidence exceeding 1 in 10,000 probability of false negative.

Ottens, Brian P.↗

Intercomparison of the gold, platinum, and MgO pressure scales up to 140 GPa and 2500 K

In order to intercalibrate the equations of state (EOSs) of the three widely used pressure standards, gold, platinum, and MgO, we have measured their unit cell volumes together in the laser–heated diamond anvil cell up to 140 GPa and 2500 K. At 300 K, three standards agree with each other within ±2.5 GPa to 135 GPa if the EOSs measured in quasi–hydrostatic media are used. We further refined the EOSs at 300 K, making them consistent with each other within ±1 GPa up to 135 GPa. At high temperature ( T ), the three standards match the best within ±1 GPa between 40 and 140 GPa, when we use the scales by Dorogokupets and Dewaele (2007). However, a 2–3 GPa discrepancy remains at 20–40 GPa and 1500–2000 K, with gold yielding the highest pressure ( P ). The pressure discrepancy is likely related to steep decreases in the Grüneisen parameter, the anharmonicity, and/or the electronic effects for the standards at the P–T conditions. Because gold melts near the temperatures expected for the mantle transition zone, severe anharmonic effects expected under premelting conditions make gold unsuitable for determining the phase boundaries in the region. The pressure scales by Dorogokupets and Dewaele (2007) provide tighter constrains on the Clapeyron slopes of the postspinel boundary to –2.0 to –2.7 MPa/K and the postperovskite boundary to 7–10 MPa/K. In conclusion, the data and refined EOSs presented here allow for reliable comparisons among experiments with different pressure standards for the entire P–T conditions expected for the Earth's lower mantle.

58 GEOSCIENCES↗

Chasing the Future: How Will Ocean Change Affect Marine Life?

Understanding the potential consequences of rising ocean carbon levels and related ocean changes for marine life and ecosystems is a high priority for the ocean research community and marine resource management. In the mid-1990s, two geoengineering proposals to mitigate global warming by carbon sequestration in the deep sea led to research measuring the effects of increased deep ocean carbon dioxide levels on marine animals. A few years later, ocean acidification and its effects on marine life became an international research priority. Here we provide an overview of several technical developments by scientists and engineers at the Monterey Bay Aquarium Research Institute (MBARI) that have enabled and enhanced deep-sea exploration and experiments to assess the effects of changing ocean conditions on benthic marine animals. Improvements in remotely operated vehicles (ROVs) have increased the efficiency of dive operations and enabled more complex measurements and experiments at great ocean depths. In situ respirometers and Free Ocean CO 2 Enrichment (FOCE) mesocosms have allowed measurement of physiological and behavioral responses of deep-sea animals to environmental change. A laboratory-based, gas-controlled aquarium system that regulates oxygen and pH in chilled waters was engineered to measure the physiological responses of deep-sea animals and biological communities to expected future environmental conditions. Recently, MBARI engineers and scientists developed an Upwelling Simulator, a lab-based aquarium control system that mimics ocean conditions during coastal upwelling. This system is programmable, allowing independent control of pH, oxygen, and temperature to enable experiments that examine the effects of present-day upwelling conditions, expected future conditions, or other changes in these environmental conditions. In sum, collaboration between the marine operations group, engineers, and scientists at MBARI has advanced methods to explore the ocean and understand the consequences of ocean change for marine organisms and ecosystems.

54 ENVIRONMENTAL SCIENCES↗

Environmental Loss Characterization of an Advanced Stirling Convertor (ASC-E2) Insulation Package Using a Mock Heater Head

The U.S. Department of Energy (DOE) and Lockheed Martin Space Systems Company (LMSSC) have been developing the Advanced Stirling Radioisotope Generator (ASRG) for use as a power system for space science missions. This generator would use two highefficiency Advanced Stirling Convertors (ASCs), developed by Sunpower Inc. and NASA Glenn Research Center (GRC). As part of ground testing of these ASCs, different operating conditions are used to simulate expected mission conditions. These conditions require achieving a specified electrical power output for a given net heat input. While electrical power output can be precisely quantified, thermal power input to the Stirling cycle cannot be directly measured. In an effort to improve net heat input predictions, the Mock Heater Head was developed with the same relative thermal paths as a convertor using a conducting rod to represent the Stirling cycle and tested to provide a direct comparison to numerical and empirical models used to predict convertor net heat input. The Mock Heater Head also served as the pathfinder for a higher fidelity version of validation test hardware, known as the Thermal Standard. This paper describes how the Mock Heater Head was tested and utilized to validate a process for the Thermal Standard.

Schifer, Nicholas A.↗

Overview of Heat Addition and Efficiency Predictions for an Advanced Stirling Convertor

The U.S. Department of Energy (DOE) and Lockheed Martin Space Systems Company (LMSSC) have been developing the Advanced Stirling Radioisotope Generator (ASRG) for use as a power system for space science missions. This generator would use two high-efficiency Advanced Stirling Convertors (ASCs), developed by Sunpower Inc. and NASA Glenn Research Center (GRC). The ASCs convert thermal energy from a radioisotope heat source into electricity. As part of ground testing of these ASCs, different operating conditions are used to simulate expected mission conditions. These conditions require achieving a particular operating frequency, hot end and cold end temperatures, and specified electrical power output for a given net heat input. Microporous bulk insulation is used in the ground support test hardware to minimize the loss of thermal energy from the electric heat source to the environment. The insulation package is characterized before operation to predict how much heat will be absorbed by the convertor and how much will be lost to the environment during operation. In an effort to validate these predictions, numerous tasks have been performed, which provided a more accurate value for net heat input into the ASCs. This test and modeling effort included: (a) making thermophysical property measurements of test setup materials to provide inputs to the numerical models, (b) acquiring additional test data that was collected during convertor tests to provide numerical models with temperature profiles of the test setup via thermocouple and infrared measurements, (c) using multidimensional numerical models (computational fluid dynamics code) to predict net heat input of an operating convertor, and (d) using validation test hardware to provide direct comparison of numerical results and validate the multidimensional numerical models used to predict convertor net heat input. This effort produced high fidelity ASC net heat input predictions, which were successfully validated using specially designed test hardware enabling measurement of heat transferred through a simulated Stirling cycle. The overall effort and results are discussed.

Wilson, Scott D.↗

A Computational Methodology for Simulating Thermal Loss Testing of the Advanced Stirling Convertor

The U.S. Department of Energy (DOE) and Lockheed Martin Space Systems Company (LMSSC) have been developing the Advanced Stirling Radioisotope Generator (ASRG) for use as a power system for space science missions. This generator would use two highefficiency Advanced Stirling Convertors (ASCs), developed by Sunpower Inc. and NASA Glenn Research Center (GRC). The ASCs convert thermal energy from a radioisotope heat source into electricity. As part of ground testing of these ASCs, different operating conditions are used to simulate expected mission conditions. These conditions require achieving a particular operating frequency, hot end and cold end temperatures, and specified electrical power output for a given net heat input. In an effort to improve net heat input predictions, numerous tasks have been performed which provided a more accurate value for net heat input into the ASCs, including the use of multidimensional numerical models. Validation test hardware has also been used to provide a direct comparison of numerical results and validate the multi-dimensional numerical models used to predict convertor net heat input and efficiency. These validation tests were designed to simulate the temperature profile of an operating Stirling convertor and resulted in a measured net heat input of 244.4 W. The methodology was applied to the multi-dimensional numerical model which resulted in a net heat input of 240.3 W. The computational methodology resulted in a value of net heat input that was 1.7 percent less than that measured during laboratory testing. The resulting computational methodology and results are discussed.

Reid, Terry V.↗

Evaluation of Advanced Stirling Convertor Net Heat Input Correlation Methods Using a Thermal Standard

The U.S. Department of Energy (DOE) and Lockheed Martin Space Systems Company (LMSSC) have been developing the Advanced Stirling Radioisotope Generator (ASRG) for use as a power system for space science missions. This generator would use two high-efficiency Advanced Stirling Convertors (ASCs), developed by Sunpower Inc. and NASA Glenn Research Center (GRC). The ASCs convert thermal energy from a radioisotope heat source into electricity. As part of ground testing of these ASCs, different operating conditions are used to simulate expected mission conditions. These conditions require achieving a particular operating frequency, hot end and cold end temperatures, and specified electrical power output for a given net heat input. In an effort to improve net heat input predictions, numerous tasks have been performed which provided a more accurate value for net heat input into the ASCs, including testing validation hardware, known as the Thermal Standard, to provide a direct comparison to numerical and empirical models used to predict convertor net heat input. This validation hardware provided a comparison for scrutinizing and improving empirical correlations and numerical models of ASC-E2 net heat input. This hardware simulated the characteristics of an ASC-E2 convertor in both an operating and non-operating mode. This paper describes the Thermal Standard testing and the conclusions of the validation effort applied to the empirical correlation methods used by the Radioisotope Power System (RPS) team at NASA Glenn.

Briggs, Maxwell H.↗

Performance of an Advanced Stirling Convertor Based on Heat Flux Sensor Measurements

The U.S. Department of Energy (DOE) and Lockheed Martin Space Systems Company (LMSSC) have been developing the Advanced Stirling Radioisotope Generator (ASRG) for use as a power system for space science missions. This generator would use two highefficiency Advanced Stirling Convertors (ASCs), developed by Sunpower, Inc., and NASA Glenn Research Center. The ASCs convert thermal energy from a radioisotope heat source into electricity. As part of ground testing of these ASCs, different operating conditions are used to simulate expected mission conditions. These conditions require achieving a particular operating frequency, hot-end and cold-end temperatures, and specified electrical power output for a given heat input. It is difficult to measure heat input to Stirling convertors due to the complex geometries of the hot components, temperature limits of sensor materials, and invasive integration of sensors. A thin-film heat flux sensor was used to directly measure heat input to an ASC. The effort succeeded in designing and fabricating unique sensors, which were integrated into a Stirling convertor ground test and exposed to test temperatures exceeding 700 C in air for 10,000 hr. Sensor measurements were used to calculate thermal efficiency for ASC-E (Engineering Unit) #1 and #4. The post-disassembly condition of the sensors is also discussed.

Wilson, Dcott D.↗

Performance of an Advanced Stirling Convertor Based on Heat Flux Sensor Measurements

The U.S. Department of Energy (DOE) and Lockheed Martin Space Systems Company (LMSSC) have been developing the Advanced Stirling Radioisotope Generator (ASRG) for use as a power system for space science missions. This generator would use two high-efficiency Advanced Stirling Convertors (ASCs), developed by Sunpower, Inc., and NASA Glenn Research Center. The ASCs convert thermal energy from a radioisotope heat source into electricity. As part of ground testing of these ASCs, different operating conditions are used to simulate expected mission conditions. These conditions require achieving a particular operating frequency, hot-end and cold-end temperatures, and specified electrical power output for a given heat input. It is difficult to measure heat input to Stirling convertors due to the complex geometries of the hot components, temperature limits of sensor materials, and invasive integration of sensors. A thin-film heat flux sensor was used to directly measure heat input to an ASC. The effort succeeded in designing and fabricating unique sensors, which were integrated into a Stirling convertor ground test and exposed to test temperatures exceeding 700 C in air for 10,000 hr. Sensor measurements were used to calculate thermal efficiency for ASC-E (Engineering Unit) #1 and #4. The post-disassembly condition of the sensors is also discussed.

Wilson, Scott D.↗

AFM Slip Length Measurements for Water at Selected Phyllosilicate Surfaces

Most reported slip length measurements have been made at the surfaces of synthetic materials and modified synthetic materials. In contrast, few slip length measurements at the surface of unmodified natural mineral surfaces have been reported. In this regard, flow at the silica face surfaces of the phyllosilicate minerals, talc and mica, was considered. A slip boundary condition was expected at the nonpolar hydrophobic silica surface of talc leading to enhanced flow, and a no-slip boundary condition was expected at the hydrophilic silica surface of mica. Atomic force microscopy (AFM) slip length measurements were made at the talc and mica surfaces. The slip length results for the hydrophobic silica surface of talc were contrasted to the results for the hydrophilic silica surface of mica (no-slip flow). The results are discussed based on molecular dynamics simulations (MDS), as reported in the literature, and AFM images of surface nanobubbles. For nonpolar hydrophobic surfaces (such as talc), it is doubtful that the MDS interfacial water structure and the water exclusion zone (3.2 Å) account for the AFM slip flow with slip lengths as great as 95 nm. Rather, a better explanation for the AFM slip flow condition is based on reduced interfacial viscosity due to the presence of dissolved gas and the accommodation of pancake nanobubbles at the talc surface having a height dimension of magnitude similar to the slip length.

42 ENGINEERING↗