Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “compositional noise”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

A linear shift-invariant image preprocessing technique for multispectral scanner systems

A linear shift-invariant image preprocessing technique is examined which requires no specific knowledge of any parameter of the original image and which is sufficiently general to allow the effective radius of the composite imaging system to be arbitrarily shaped and reduced, subject primarily to the noise power constraint. In addition, the size of the point-spread function of the preprocessing filter can be arbitrarily controlled, thus minimizing truncation errors.

Mcgillem, C. D.↗

Fluid dynamic aspects of jet noise generation

The location of the noise sources within jet flows, their relative importance to the overall radiated field, and the mechanisms by which noise generation occurs, are studied by detailed measurements of the level and spectral composition of the radiated sound in the far field. Directional microphones are used to isolate the contribution to the radiated sound of small regions of the flow, and for cross-correlation between the radiated acoustic field and either the velocity fluctuations or the pressure fluctuations in the source field. Acquired data demonstrate the supersonic convection of the acoustic field and the resulting limited upstream influence of the signal source, as well as a possible increase of signal strength as it propagates toward the centerline of the flow.

Source record↗

Ghost suppression in image restoration filtering

An optimum image restoration filter is described in which provision is made to constrain the spatial extent of the restoration function, the noise level of the filter output and the rate of falloff of the composite system point-spread away from the origin. Experimental results show that sidelobes on the composite system point-spread function produce ghosts in the restored image near discontinuities in intensity level. By redetermining the filter using a penalty function that is zero over the main lobe of the composite point-spread function of the optimum filter and nonzero where the point-spread function departs from a smoothly decaying function in the sidelobe region, a great reduction in sidelobe level is obtained. Almost no loss in resolving power of the composite system results from this procedure. By iteratively carrying out the same procedure even further reductions in sidelobe level are obtained. Examples of original and iterated restoration functions are shown along with their effects on a test image.

Riemer, T. E.↗

Statistical White-Line Analysis in High-Throughput TXM-XANES for Chemical State Quantification

The transmission X-ray microscopy (TXM) based X-ray absorption near-edge structure (XANES) technique provides three-dimensional mapping of element-specific chemical states at nanometer-scale spatial resolution and micrometer-scale fields of view. However, compared to conventional volume-averaged XANES (VA-XANES) measurements, the inherently small voxel size in TXM-XANES leads to a lower signal-to-noise ratio, making full-spectrum analysis computationally demanding and less robust. Here, we present the structural and compositional conditions for a statistical white-line analysis framework under which chemical state information can be directly extracted from the white-line peak position in voxel spectra without the need for voxel-wise background subtraction or normalization, under well-defined structural and compositional conditions. The method is validated on layered oxide cathode materials, where low-order polynomial fitting accurately reproduces white-line features, and the extracted energy distributions correlate strongly with VA-XANES results. This statistical approach enables high-throughput, dose-efficient, and noise-robust chemical state quantification in TXM-XANES, offering broad applicability to functional materials requiring nanoscale oxidation-state mapping.

TXM↗

Testing and Analysis of a Composite Non-Cylindrical Aircraft Fuselage Structure : Severe Damage - Part II

The Environmentally Responsible Aviation Project aimed to develop aircraft technologies enabling significant fuel burn and community noise reductions. Small incremental changes to the conventional metallic alloy-based 'tube and wing' configuration were not sufficient to achieve the desired metrics. One airframe concept identified by the project as having the potential to dramatically improve aircraft performance was a composite-based hybrid wing body configuration. Such a concept, however, presented inherent challenges stemming from, among other factors, the necessity to transfer wing loads through the entire center fuselage section which accommodates a pressurized cabin confined by flat or nearly flat panels. This paper discusses a finite element analysis and the testing of a large-scale hybrid wing body center section structure developed and constructed to demonstrate that the Pultruded Rod Stitched Efficient Unitized Structure concept can meet these challenging demands of the next generation airframes. Part II of the paper considers the final test to failure of the test article in the presence of an intentionally inflicted severe discrete source damage under the wing up-bending loading condition. Finite element analysis results are compared with measurements acquired during the test and demonstrate that the hybrid wing body test article was able to redistribute and support the required design loads in a severely damaged condition.

Przekop, Adam↗

Preliminary Assessment of the Interior Noise Environment in the Large Civil Tiltrotor (LCTR2)

The second-generation Large Civil Tiltrotor (LCTR2) serves as a representative vehicle under the NASA Fundamental Aeronautics Program (FAP) Subsonic Rotary Wing (SRW) project with a design goal to transport 90 passengers over a distance of 1800 km at a speed of 550 km/hr. The tiltrotor combines the vertical lift capability of a helicopter with the speed, altitude, and range of a turboprop airplane. The blade-passage frequency of the four-bladed rotor is as low as 6.9 Hz during cruise conditions. The resulting low-frequency acoustic excitation and its harmonics, combined with the anticipated use of lightweight composite and sandwich materials for the fuselage sidewall, may pose a challenge to achieving acceptable interior noise levels. The objective of the present study is to perform a preliminary assessment of the expected interior noise environment in the LCTR2 cabin. The approach includes a combination of semi-empirical, analytical, and statistical energy analysis methods. Because the LCTR2 is a notional vehicle, the prediction approach was also applied to the XV-15 tiltrotor and Bombardier Q400 turobprop aircraft to compare predictions with publicly available experimental data. Guidance for the expected interior noise levels in the LCTR2 was obtained by considering both the predicted exterior noise levels and the transmission loss of a basic fuselage sidewall consisting of a skin, porous layer and a trim panel. Structural and acoustic resonances are expected to coincide with low order harmonics of the blade passage frequency. The estimated sound pressure levels in the LCTR2 may not be acceptable when evaluated against known characteristics of human response to low frequency sound.

Grosveld, Ferdinand W.↗

Nozzle material requirements and the status of intermetallic matrix composites

The HSCT exhaust nozzle must manage high temperature exhaust gases and pressure gradients while meeting HSCT economic and noise goals. The important features and requirements for an HSCT exhaust nozzle are shown for a 2DCD (two-dimensional convergent-divergent) design. The same requirements would apply to an axisymmetric design. Exhaust nozzle weight has an adverse effect on the overall aircraft range, payload, and engine specific fuel consumption and is therefore the primary driver for advanced exhaust nozzle materials. Because of the large airflow and pressure gradients, exhaust nozzles are extremely large and heavy when made from current materials. The use of advanced materials with higher specific strength will reduce the weight of exhaust nozzle components. In addition to the flow of high-temperature exhaust gases into the exhaust nozzle, ambient air is entrained to reduce gas exit velocities and suppress sound. This leads to components exposed to extremely high temperature gradients and, hence, high thermal stresses. Further, exhaust gases are highly oxidizing; material environmental resistance will be an important factor for long life. Several viable concepts have been identified to reduce noise through the mixture of exhaust and ambient air. Sound can be further suppressed by acoustic panels that absorb high-frequency noise.

Johnson, Andrew M.↗

Transcript level and sequence determinants of protein abundance and noise in Escherichia coli

The range over which a protein is expressed, and its cell-to-cell variability, is often thought to be linked to the demand for its activity. Steady-state protein level is determined by multiple mechanisms controlling transcription and translation, many of which are limited by DNA- and RNA-encoded signals that affect initiation, elongation and termination of polymerases and ribosomes. We performed a comprehensive analysis of >100 sequence features to derive a predictive model composed of a minimal non-redundant set of factors explaining 66% of the total variation of protein abundance observed in >800 genes in Escherichia coli. The model suggests that protein abundance is primarily determined by the transcript level (53%) and by effectors of translation elongation (12%), whereas only a small fraction of the variation is explained by translational initiation (1%). Our analyses uncover a new sequence determinant, not previously described, affecting translation initiation and suggest that elongation rate is affected by both codon biases and specific amino acid composition. We also show that transcription and translation efficiency may have an effect on expression noise, which is more similar than previously assumed.

59 BASIC BIOLOGICAL SCIENCES↗

Composites for Advanced Drive Systems

With the desire for increased power/weight for advanced drive system configurations, the investigation of materials, like composites is being explored to determine the feasibility of integration into advanced drive systems. This area of research directly aligns with the vision of the NASA (National Aeronautics and Space Administration) Revolutionary Vertical Lift Technology (RVLT) Project, which is to enable a generation of vertical lift vehicles that can achieve aggressive goals in the areas of high speed, high efficiency, high performance, low noise, and low emissions.Composite materials are lightweight, especially when comparing to the metallic materials commonly utilized in rotorcraft drive systems. By integrating composite materials into the drive system, the potential for improvements to power/weight exists as well as other potential benefits such as reductions in vibration and/or noise. Each of these areas of potential benefit will largely influence the overall performance and reliability of future vertical lift vehicles. Prior NASA research has been performed that developed a prototype hybrid double helical bull gear which was successfully demonstrated (LaBerge, Kelsen E.; Handschuh, Robert F.; Roberts, Gary; Thorp, Scott;, 2016) and current NASA research is being performed to optimize the hybrid gear design.While the potential benefits of composite materials in vertical lift drive systems mentioned above are highly desirable, many challenges exist that need to be addressed. To address the benefits and challenges with the integration of composite materials in advanced vertical lift drive systems, the identification of advanced drive system configurations and technical challenges is required. For this project, Bell Helicopter Textron identified an advanced drive system configuration and provided conceptual designs for this advanced drive system configuration, identified technical challenges, and provided recommendations as to how those challenges can be overcome.

transmission↗

Wind tunnel mass spectrometer design study

The sampling probe to measure the free stream gas composition in a hypersonic wind tunnel is described. Using a free expansion of the continuum flow, a series of sampling inlet-pumping stages is evaluated. Mass analysis is carried out with a quadrupole mass spectrometer employing a crossed electron beam, molecular beam ion source, and an off-axis electron multiplier. The spatial distribution of the sampled molecular flux and the pumping requirements are evaluated for varying inlet conditions of gas density and flow velocity. The signal-to-noise ratio of the molecular beam formed by this series of coaxial inlets is also determined. The signal-to-noise ratio of the unscattered flux is sufficiently high that an unambiguous determination of the beam composition and of the free stream gas properties can be made. The magnitude of the detected signal is sufficiently high that measurement of trace constituents two orders of magnitude below the primary beam signal can be made.

Hueser, J. E.↗

Surface Composition of (99942) Apophis

On 2029 April 13, near-Earth asteroid (NEA) (99942) Apophis will pass at a distance of ∼6 Earth radii from Earth. This event will provide researchers with a unique opportunity to study the effects of tidal forces experienced by an asteroid during a close encounter with a terrestrial planet. Binzel et al. predicted that close flybys of terrestrial planets by NEAs would cause resurfacing of their regolith due to seismic shaking. In this work, we present the best pre-encounter near-infrared spectra of Apophis obtained so far. These new data were obtained during the 2013 apparition using the NASA Infrared Telescope Facility (IRTF). We found that our spectral data is consistent with previous observations by Binzel et al. but with a much higher signal-to-noise ratio. Spectral band parameters were extracted from the spectra and were used to determine the composition of the asteroid. Using a naïve Bayes classifier, we computed the likelihood of Apophis being an LL chondrite to be >99% based on mol% of Fa versus Fs. Using the same method, we estimated a probability of 89% for Apophis being an LL chondrite based on ol/(ol+px) and Fs. The results from the dynamical model indicate that the most likely source region for Apophis is the ν {sub 6} resonance in the inner main belt. Data presented in this study (especially Band I depth) could serve as a baseline to verify seismic shaking during the 2029 encounter.

79 ASTRONOMY AND ASTROPHYSICS↗

Testing and Analysis of a Composite Non-Cylindrical Aircraft Fuselage Structure: Ultimate Design Loads - Part 1

The Environmentally Responsible Aviation Project aimed to develop aircraft technologies enabling significant fuel burn and community noise reductions. Small incremental changes to the conventional metallic alloy-based 'tube and wing' configuration were not sufficient to achieve the desired metrics. One airframe concept identified by the project as having the potential to dramatically improve aircraft performance was a composite-based hybrid wing body configuration. Such a concept, however, presented inherent challenges stemming from, among other factors, the necessity to transfer wing loads through the entire center fuselage section which accommodates a pressurized cabin confined by flat or nearly flat panels. This paper discusses finite element analysis and testing of a large-scale hybrid wing body center section structure developed and constructed to demonstrate that the Pultruded Rod Stitched Efficient Unitized Structure concept can meet these challenging demands of the next generation airframes. Part I of the paper considers the five most critical load conditions, which are internal pressure only and positive and negative g-loads with and without internal pressure. Analysis results are compared with measurements acquired during testing. Performance of the test article is found to be closely aligned with predictions and, consequently, able to support the hybrid wing body design loads in pristine and barely visible impact damage conditions.

Przekop, Adam↗

The Composite Infrared Spectrometer

The Composite Infrared Spectrometer (CIRS) is a remote sensing instrument to be flown on the Cassini orbiter. It contains two Fourier transform spectrometers covering wavelengths of 7-1000 microns. The instrument is expected to have higher spectral resolution, smaller field of view, and better signal-to-noise performance than its counterpart, IRIS, on the Voyager missions. These improvements allow the study of the variability of the composition and temperature of the atmospheres of both Saturn and Titan with latitude, longitude and height, as well as allowing the possibility of discovery of previously undetected chemical species in these atmospheres. The long wavelengths accessible to CIRS allow sounding deeper into both atmospheres than was possible with IRIS.

Calcutt, Simon↗

One dimensional shock initiation of hot isostatically pressed composition B

Twelve one dimensional shock experiments have been carried out on the UK isostatically pressed Composition B (59.5% RDX, 39.5% TNT, 1% wax) comprising of seven sustained pulse experiments and three short shock experiments using the embedded gauge technique at the Los Alamos National Laboratory gas gun facility. The evolution of the reactive growth at and behind the shock front has been measured along with the run to detonation distance. Two low pressure experiments have also been carried out to obtain non-reactive equation of state data. These data have been used to create the Pop plot and Hugoniot states for the UK Comp B. The shock initiation behavior of the UK Comp B has been compared to that of the equivalent US composition. The reactive growth shows a feature that was observed in the US composition in which the wave profiles display a high level of pre-detonation noise. This was hypothesized to be due to a piezoelectric effect in the RDX crystals. The results of these experiments have shown that this effect may be localized in the ε phase at shock pressures in the region of 4.15 GPa and above.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

ANALYSIS OF THE EARLY-TIME OPTICAL SPECTRA OF SN 2011fe IN M101

The nearby Type Ia supernova (SN Ia) SN 2011fe in M101 (cz = 241 km s{sup -1}) provides a unique opportunity to study the early evolution of a 'normal' SN Ia, its compositional structure, and its elusive progenitor system. We present 18 high signal-to-noise spectra of SN 2011fe during its first month beginning 1.2 days post-explosion and with an average cadence of 1.8 days. This gives a clear picture of how various line-forming species are distributed within the outer layers of the ejecta, including that of unburned material (C+O). We follow the evolution of C II absorption features until they diminish near maximum light, showing overlapping regions of burned and unburned material between ejection velocities of 10,000 and 16,000 km s{sup -1}. This supports the notion that incomplete burning, in addition to progenitor scenarios, is a relevant source of spectroscopic diversity among SNe Ia. The observed evolution of the highly Doppler-shifted O I {lambda}7774 absorption features detected within 5 days post-explosion indicates the presence of O I with expansion velocities from 11,500 to 21,000 km s{sup -1}. The fact that some O I is present above C II suggests that SN 2011fe may have had an appreciable amount of unburned oxygen within the outer layers of the ejecta.

79 ASTRONOMY AND ASTROPHYSICS↗

Synchrotron infrared imaging of advanced glycation endproducts (AGEs) in cardiac tissue from mice fed high glycemic diets

Recent research findings correlate an increased risk for dieases such as diabetes, macular degeneration and cardiovascular disease (CVD) with diets that rapidly raise the blood sugar levels; these diets are known as high glycemic index (GI) diets which include white breads, sodas and sweet deserts. Lower glycemia diets are usually rich in fruits, non-starchy vegetables and whole grain products. The goal of our study was to compare and contrast the effects of a low vs. high glycemic diet using the biochemical composition and microstructure of the heart. The improved spatial resolution and signal-to-noise for SR-FTIR obtained through the coupling of the bright synchrotron infrared photon source to an infrared spectral microscope enabled the molecular-level observation of diet-related changes within unfixed fresh frozen histologic sections of mouse cardiac tissue. High and low glycemic index (GI) diets were started at the age of five-months and continued for one year, with the diets only differing in their starch distribution (high GI diet = 100% amylopectin versus low GI diet = 30% amylopectin/70% amylose). Serial cryosections of cardiac tissue for SR-FTIR imaging alternated with adjacent hematoxylin and eosin (H&E) stained sections allowed not only fine-scale chemical analyses of glycogen and glycolipid accumulation along a vein as well as protein glycation hotspots co-localizing with collagen cold spots but also the tracking of morphological differences occurring in tandem with these chemical changes. As a result of the bright synchrotron infrared photon source coupling, we were able to provide significant molecular evidence for a positive correlation between protein glycation and collagen degradation in our mouse model. Our results bring a new insight not only to the effects of longterm GI dietary practices of the public but also to the molecular and chemical foundation behind the cardiovascular disease pathogenesis commonly seen in diabetic patients.

59 BASIC BIOLOGICAL SCIENCES↗

Automated synthesis of transonic transports.

The development of a vehicle synthesis program, called TRANSYN, designed to perform automated preliminary design of long-haul transport aircraft is briefly described. The TRANSYN-TST program was used in a study of commercial transonic transports designed for introduction in the early 1980s. The optimum engine cycles of all the study aircraft are within the current state-of-the-art, but fan noise suppression will be required to meet the noise requirements of FAR Part 36. It was found that full use of advanced composite materials in the wing and fuselage structure is neutrally cost effective when compared with aluminum for aircraft designed to cruise in the low transonic regime (Mach 0.90 to 1.0), but that such materials are very cost effective for aircraft designed to cruise in the high transonic regime (Mach 1.0 to 1.15). Finally, increasing speed results in reduced trip times with at most very slight increases in cost in the low transonic regime, but cruise speeds in the high transonic regime result in a significant economic penalty for the conventional configurations considered in this study.

Ardema, M. D.↗

Economic impact of applying advanced technologies to transport airplanes.

Various technologies have been studied which could have application to the design of future transport airplanes. These technologies include the use of supercritical aerodynamics, composite materials, and active control systems, together with advanced engine designs that provide lower noise and pollutant levels. The economic impact of each technology is shown for a typical fleet of 195-passenger, transcontinental commercial transports cruising at both 0.9M and 0.98M. Comparisons are made with conventional transports cruising at 0.82M. Effects of combining the technologies are discussed. An R & D program aimed at bringing the technologies to fruition is outlined.

Carline, A. J. K.↗