Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “coating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

High Average Power RF Window with Improved Multipactor Coating

Multipactor emission can be a serious issue for vacuum electron devices operating at megawatt power levels. It can lead to catastrophic failure from surface arcs or excessive heating of ceramic windows. Titanium nitride is effective at suppressing multipactor emission; however, sputter coating is not strongly bonded to surfaces and issue related to lifetime have arisen. It’s difficult to ensure a uniform coating over large surfaces. This research investigated atomic layer deposition (ALD) as an improved alternative to sputtered coatings. Test windows were fabricated and coated with TiN using ALD, then tested for RF loss and secondary emission. All ALD samples showed RF loss less than 0.01dB with secondary emission yield equal to or better than reported measurements with sputter coated windows. The program also designed a preliminary ALD system capable of coating windows up to 24 inches in diameter.

43 PARTICLE ACCELERATORS↗
DOE OSTI2022

Enable High-Energy LiNi0.5Co0.2Mn0.3O2 by Ultra-Thin Coating through Wet Impregnation

A high cut-off voltage is required for nickel-rich layered oxide LiNixCoyMnzO2 (NCM) to meet the high energy density requirement of lithium-ion batteries in electric vehicles. However, such a high voltage application leads to an unstable interface between NCM and liquid electrolytes. To stabilize the interface, the facile wet impregnation method has been developed to apply an ultra-thin Al2O3 coating layer on the NCM particles. This coating layer was found to have a strong interaction with the NCM and resulted in Al-doped NCM at the surface structure of NCM. The change of surface structure can not only reduce the surface resistance of lithium diffusion of LiNi0.5Co0.2Mn0.3O2 (NCM523), but also stabilize the solid electrolyte interface between NCM523 and the electrolyte with the cut-off voltage of 4.5 V vs. Li/Li+. Compared to other coating methods, wet impregnation coating can provide an ultra-thin and uniform coating with surface doping on NCM particles. Furthermore, this scalable coating method can be applied to various electrode materials without adding much additional cost.

25 ENERGY STORAGE↗
DOE OSTI2021

Fluorescent CQD-Doped Styrene Acrylic Emulsion Coating Film with Enhanced Optical Properties

Styrene acrylic emulsions (SAEs) have emerged as a promising material for water-based coatings. However, they are still limited by their own defects in practical applications, poor weatherability, and degradation of performance at lower or higher temperatures. Here, we introduce a facile approach to producing fluorescent carbon quantum dots (CQDs) from wood processing residues and fabricating fluorescent CQD/SAE coating films via emulsion-casting. The addition of the fluorescent CQDs enhanced the optical performance of the CQD/SAE coating films. The fluorescent CQDs were prepared via a hydrothermal approach and were obtained after heating at 180 °C for 6 h at a reaction concentration of 50 mg/mL. The synthesized CQDs resulted in a high fluorescence, and the CQDs had an average size of 1.63 nm. Various concentrations of the fluorescent CQDs were doped into the SAE coating film, which improved its optical properties. We also characterized and discussed the products and then explored their optical properties. This study presents the potential of fluorescent CQD/SAE coating films for applications in anti-counterfeiting coatings, fluorescent adhesives, and papermaking.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Self-Cleaning Highly Porous TiO 2 Coating Designed by Swelling-Assisted Sequential Infiltration Synthesis (SIS) of a Block Copolymer Template

Photocatalytic self-cleaning coatings with a high surface area are important for a wide range of applications, including optical coatings, solar panels, mirrors, etc. Here, we designed a highly porous TiO 2 coating with photoinduced self-cleaning characteristics and very high hydrophilicity. This was achieved using the swelling-assisted sequential infiltration synthesis (SIS) of a block copolymer (BCP) template, which was followed by polymer removal via oxidative thermal annealing. The quartz crystal microbalance (QCM) was employed to optimize the infiltration process by estimating the mass of material infiltrated into the polymer template as a function of the number of SIS cycles. This adopted swelling-assisted SIS approach resulted in a smooth uniform TiO 2 film with an interconnected network of pores. The synthesized film exhibited good crystallinity in the anatase phase. The resulting nanoporous TiO 2 coatings were tested for their functional characteristics. Exposure to UV irradiation for 1 h induced an improvement in the hydrophilicity of coatings with wetting angle reducing to unmeasurable values upon contact with water droplets. Furthermore, their self-cleaning characteristics were tested by measuring the photocatalytic degradation of methylene blue (MB). The synthesized porous TiO 2 nanostructures displayed promising photocatalytic activity, demonstrating the degradation of approximately 92% of MB after 180 min under ultraviolet (UV) light irradiation. Thus, the level of performance was comparable to the photoactivity of commercial anatase TiO 2 nanoparticles of the same quantity. Our results highlight a new robust approach for designing hydrophilic self-cleaning coatings with controlled porosity and composition.

36 MATERIALS SCIENCE↗
DOE OSTI2020

An Experimental Investigation of Multilayer Flow in a Slide Die Coating Process

Roll-to-roll coating technology has been actively applied not only for conventional film production but also for emerging energy devices such as organic solar cells, organic light emitting diodes, batteries, smart windows, and fuel cells. The devices are multilayer structures requiring several coating and drying steps when implemented in a serial fashion, which increases capital costs and energy consumption. Simultaneous multilayer (ML) coating technologies present an opportunity for cost reductions and improved process efficiency by reducing equipment footprint and the number of process steps. In this talk, we experimentally investigate ML slide die coating flow for the manufacturing of fuel cell membrane electrode assemblies (MEAs). For ML slide coating, understanding fluid properties such as density, surface tension, and viscosity are necessary for stable flows and limiting intermixing of the miscible layers. Here, we utilize a design-of-experiment methodology - Box-Behnken design (BBD) - to correlate ink formulation parameters to fluid properties. Using the ink properties obtained from the BBD, we performed numerical flow simulations to obtain a proper process conditions to guide experimental coating trials. Finally, experimental verification is performed on a ML slide die and a degree of miscibility was observed for various ink formulation conditions.

28 EE - Advanced Manufacturing Office (EE-5A)↗
DOE OSTI2025

Investigation of the Mechanical Degradation of Zinc-Based Cold Spray Coatings for Steel Pipelines

Internal corrosion in wet natural gas is a big challenge in the oil and gas industry due to corrosive constituents such as carbon dioxide (CO2), hydrogen sulfide (H2S), other forms of sulfur, and water in the gas stream. To mitigate internal corrosion, zinc-based cold spray coatings were designed for use in natural gas pipelines to increase the lifespan of the pipeline network. However, one of the requirements in designing internal coatings is the resistance of the coatings to mechanical forces applied on the pipeline's internal wall during pigging operations. These forces are primarily compressive and shear/friction forces. This study examines material properties that must be considered when evaluating mechanical considerations. To determine the viability of the developed coatings with respect to the shear/friction forces, the shear adhesion and wear resistance of the materials have been evaluated. Shear adhesion testing was performed with modified clevises to determine the shear stress required to cause adhesion failure at the coating/substrate interface. Scanning electron microscopy was utilized to characterize the interfaces after failure. Wear testing was performed on coatings and pipeline materials utilizing pin-on-drum testing. These tests display the stress limitations and wear that the coatings can tolerate from pigging.

mechanical degradation↗
DOE OSTI2022

Porous but Mechanically Robust All-Inorganic Antireflective Coatings Synthesized using Polymers of Intrinsic Microporosity

Herein, we introduce polymer of intrinsic microporosity 1 (PIM-1) to design single-layer and multilayered all-inorganic antireflective coatings (ARCs) with excellent mechanical properties. Using PIM-1 as a template in sequential infiltration synthesis (SIS), we can fabricate highly uniform, mechanically stable conformal coatings of AlO x with porosities of ~50% and a refractive index of 1.41 compared to 1.76 for nonporous AlO x that is perfectly suited for substrates commonly used in high-end optical systems or touch screens (e.g., sapphire, conductive glass, bendable glass, etc.). We show that such films can be used as a single-layer ARC capable of reduction of the Fresnel reflections of sapphire to as low as 0.1% at 500 nm being deposited only on one side of the substrate. We also demonstrate that deposition of the second layer with higher porosity using block copolymers enables the design of graded-index double-layered coatings. AlO x structures with just two layers and a total thickness of less than 200 nm are capable of reduction of Fresnel reflections under normal illumination to below 0.5% in a broad spectral range with 0.1% reflection at 700 nm. Additionally, and most importantly, we show that highly porous single-layer and graded-index double-layered ARCs are characterized by high hardness and scratch resistivity. The hardness and the maximum reached load were 7.5 GPa and 13 mN with a scratch depth of about 130 nm, respectively, that is very promising for the structures consisting of two porous AlO x layers with 50% and 85% porosities, correspondingly. Such mechanical properties of coatings can also allow their application as protective layers for other optical coatings.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Fluorine-Free Superhydrophobic Coatings: Rapid Fabrication and Highly Efficient Oil/Water Separation

In this work, a rapid method is demonstrated to obtain a fluorine-free superhydrophobic/superoleophilic coating by a simple two-step method: dip-coating and oven curing. The chemical structure of the coating is based on the crosslinking reaction of an alkyl methacrylate, a dimethacrylate (crosslinker) and a silane (adhesive), using AIBN as initiator, toluene as solvent, and silica nanoparticles to enhance surface roughness. Chemorheology results show that the coating is fully cured even in 20 min at 100 °C, exhibiting a water contact angle (CA) of 162 ± 2°, sliding angle (SA) of 4 ± 1°, nanometrical structures throughout the surface, and excellent adhesion properties for the mesh screen. The coating exhibits outstanding oil/water separation efficiency (96–99%) for seven different types of oil (gasoline, diesel, petroleum ether, hexane, toluene, chloroform, and dichloromethane), and in addition presents high recyclability. Based on nonisothermal TGA, the activation energy of degradation, calculated using the Kissinger and Ozawa models, is 113.5 and 114 kJ mol -1 , respectively. Finally, the coating is thermally aged at 150 °C: the CA exhibits a smooth decrease up to 129 ± 1° at 120 min, and FTIR analysis shows structural changes possibly related to the generation of thermal oxidation products.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Grain-boundary structure and segregation in Nb 3 Sn coatings on Nb for high-performance superconducting radiofrequency cavity applications

Here, we report on atomic-scale analyses of grain boundary (GB) structures and segregation in Nb 3 Sn coatings on Nb, prepared by the vapor-diffusion process, for superconducting radiofrequency (SRF) cavity applications, utilizing atom-probe tomography, high-resolution scanning transmission electron-microscopy and first-principles calculations. We demonstrate that the chemical composition of Nb 3 Sn GBs is correlated strongly with the diffusion of Sn and Nb at GBs during the coating process. In a sample coated with a relatively large Sn flux, we observe an interfacial width of Sn segregation at a GB of ~3 nm, with a maximum concentration of ~35 at.%. After post-annealing at 1100 °C for 3 h, the Sn segregated at GBs disappears and Nb segregation is observed subsequently at GBs, indicating that Nb diffused into the Nb3Sn GBs from the Nb substrate. It is also demonstrated that the amount of Sn segregation in a Nb 3 Sn coating can be controlled by: (i) Sn flux; and (ii) the temperatures of the Nb substrates and Sn source, which may affect the overall kinetics including GB diffusion of Sn and Nb. An investigation of the correlation between the chemical compositions of GBs and Nb 3 Sn SRF cavity performance reveals that the Nb 3 Sn SRF cavities with the best performance (high-quality factors at high accelerating electric-field gradients) do not exhibit Sn segregation at GBs. Our results suggest that the chemical compositions of GBs in Nb 3 Sn coatings for SRF cavities can be controlled by GB engineering and can be utilized to optimize fabrication of high-quality Nb 3 Sn coatings for SRF cavities.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Distributed strain sensing using Bi-metallic coated fiber optic sensors embedded in stainless steel

Silica fiber optic sensors are resistant to corrosive environments and high temperatures, making them attractive candidates for harsh conditions found in nuclear and aerospace industries. Moreover, fibers can be deployed remotely for continuous measuring of spatially distributed temperatures and strains. Here, this study investigated embedding a Ni/Cu bi-metallic coated fiber in a stainless-steel 316 (SS316) matrix using laser powder bed fusion towards functionalizing metal components for site-specific health monitoring. The embedded fiber was continuously interrogated during controlled heating to 1000°C. The measured fiber strains were similar to the expected differential thermal strains between the fiber and the SS316 matrix, until divergent behavior was observed at temperatures >500°C. No debonding at the matrix–coating–fiber interfaces was observed during microscopy, but significant interactions between the coatings and matrix resulted in diffusion-driven chemistry variations and Kirkendall void formation. Applying the strain-lag theory revealed plastic behavior in the Ni coating at temperatures >500°C, limiting the strain transfer to the fiber at higher temperatures. It was estimated that the elastic modulus in the Ni coating had decreased from ~200 GPa at room temperature to below 40 GPa, starting at 600°C. The low elastic modulus above 600°C is within the margin of what the tangent modulus would be in the case of bilinear isotropic hardening. Regardless of the divergent strain transfer at higher temperatures, the fiber was exposed to the equivalent of 1.9 % engineering strain at 1000°C, but measured only a 0.7 % engineering strain due to the poor strain transfer. Although compensating for the plastic behavior of Ni proved challenging, the bonding of a brittle silica fiber to a metal matrix surviving to 1000°C invites potential iterations on coating material for future application. For example, the embedded fiber is sufficient for acoustic energy transfer, realizing high temperature distributed acoustic sensing.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Chromium-coated cladding analysis under simulated LOCA burst conditions

Of the near-term accident-tolerant fuel concepts identified, chromium coatings have been shown to slow cladding oxidation without altering fuel system geometry or greatly affecting neutronic performance. To identify how coated cladding tubes perform under high-temperature accident conditions, pressurized-tube burst tests were conducted in the Severe Accident Test Station at Oak Ridge National Laboratory. To analyze how the coating affects cladding behavior, coated and uncoated cladding burst tests were simulated by using the BISON fuel performance code. Thermocouple data from these tests were fit into axial and azimuthal profiles and combined to generate 3D cladding surface temperatures, and pressure transducer data were compared until cladding failure. Additionally, the cladding temperatures at failure and the internal gas pressure evolution show relatively good agreement between the simulation and experiment results. Simulations were then extrapolated to demonstrate the coatings effectiveness to increasing the cladding burst temperature by using a parametric evaluation of the initial tube gas pressure. This work demonstrates the possibility of an increased cladding failure margin under transient conditions due to the addition of chromium coating, and more pertinently, an increased cladding failure margin from more accurate experimental characterization.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

All-alumina quarter-wave plate coatings fabricated by glancing angle deposition using serial bideposition

Anisotropic phase retarders, used in high power laser facilities to perform polarization smoothing, can be obtained by the glancing angle deposition (GLAD) coating process. Due to its high laser resistance, the coatings are mainly made of silica. Therefore, limited attention has been given to other dielectric materials. Here we present a study on alumina GLAD anisotropic coatings; a material with high laser resistance, higher birefringence and lower environmental sensitivity than silica. Since the anisotropy is related to the coatings microstructure through the deposition angle, samples were coated at angles varying from ± 68° to ± 82° using the serial bideposition technique. They were characterized by ellipsometry, polarimetry, spectrophotometry and electron microscopy. We showed that the highest birefringence is obtained at a deposition angle of ± 76° with an in-plane value of 0.053. Based on these results, a quarter-wave plate at 351 nm was designed as a multilayer with seven pairs of anisotropic layers deposited at ± 76° and isotropic layers deposited at 0°. The fabricated coating exhibited a uniform retardance of 88.51 ± 0.45 nm. The alumina GLAD wave plates presented here, open the door to new possibilities in the laser field and especially in the field of fusion energy.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Coating adhesion of a chromate-containing epoxy primer on Al2024-T3 surface processed by laser-interference

In this work, the coating adhesion test results are presented for a primer that was coated on laser-interference structured surfaces of as-received Al2024-T3 specimens, i.e., without employing any polishing, cleaning, or any other surface alteration techniques. All of the laser-interference processing was performed by splitting the primary beam of a Q-switched Nd:YAG pulsed nanosecond laser into two beams and focused them to the same spot. The specimens were spray painted with a chromate-containing epoxy primer, CA7233, compliant to MIL-PRF-23377 Type I Class C2 specification. The adhesion of primer on Al surface with different treatments was assessed using the ASTM D3359 X-cut and cross-hatch tests. It was found that the laser processed specimens meet the performance requirements in the coating adhesion specifications by having a higher or identical ranking for coating adhesion specimens than those prepared with current state-of-the-art chemical conversion or sulfuric acid anodizing. The rastering with either 4 mm/s or 6 mm/s with a laser fluence of 1.78 J/cm2 is recommended to attain acceptable coating adhesion, even higher than that with the anodizing surface treatment.These results indicate that laser-interference shows significant potential as a non-chemical surface preparation technique for these coatings.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Effect of Ni content in Cu 1-x Ni x coating on microstructure evolution and mechanical properties of W/Mo joint via low-temperature diffusion bonding

The 93W and Mo1 refractory metals were bonded with different Cu 1- x Ni x coating interlayers of various Ni content using plasma-activated sintering at 700 °C. The effects of the Ni content in the Cu 1- x Ni x coating interlayer on the interfacial microstructure evolution and mechanical properties of the W/Mo joints were studied. The maximum average shear strength of the W/Mo joint was 316.5 MPa when the Ni content of the Cu 1- x Ni x coating interlayer was 25 %. When the Ni content of the Cu 1- x Ni x coating interlayer was below 50 %, the atomic diffusion at the W/Mo joint interface was adequate without the formation of intermetallic compounds, as demonstrated by the High Resolution Transmission Electron Microscope analyses of the joints. The presence of Ni in Cu 1- x Ni x promoted diffusion bonding at the interface, which contributed to the high mechanical properties of the W/Mo joint. With an increase in the Ni content of the Cu 1- x Ni x coating interlayer, the MoNi intermetallic compound (IMC) nucleated and grew at the Cu 1- x Ni x coating/Mo1 interface. When the Ni content of the Cu 1- x Ni x coating interlayer was above 50 %, the generation of a brittle MoNi IMC weakened the shear strength of the W/Mo joint dramatically.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Semi-integral LOCA test of cold-spray chromium coated zircaloy-4 accident tolerant fuel cladding

Enhancing the accident tolerance of PWRs came under serious consideration following the 2011 Fukushima Daiichi nuclear power plant events. While the current nuclear fuels are based on mature technology and have an excellent operational record, further enhancing their strength through accident tolerant fuel (ATF) research and development continues to be of interest. Particularly, the chromium coated clad ATF technology represents an evolutionary change to improve the high temperature performance of existing Zircaloy claddings. Additionally, despite several years of investigation of coated cladding, the integral loss of coolant accident (LOCA) performance of chromium coated cladding has had little attention. In this work, cold-spray chromium coated zircaloy-4 claddings are evaluated using EDF's semi-integral LOCA test facility. Results show that the chromium coating induces a reduced ballooning and burst and an increased burst temperature in the investigated conditions. However, these tests exhibit limited benefits concerning the post-quench behavior of the coated specimens which occurs in the last stage of a prototypical LOCA scenario.

36 MATERIALS SCIENCE↗
DOE OSTI2021

High-temperature oxidation and quenching of chromium-coated zirconium alloy ATF cladding tubes with and w/o pre-damage

Chromium-coated zirconium alloys are one of the promising candidates for accident-tolerant fuel cladding (ATF) tubes for light water reactors (LWRs). In this study, the high temperature oxidation and degradation of two types of Cr coatings (cold spray and physical vapor deposition) with and without pre-damage by scratches were investigated on prototype rod segment samples filled with ZrO 2 pellets and tightly sealed with welded end caps. Isothermal tests at 1100 and 1200 °C were terminated by quenching with water; transient tests were performed up to 1500–1600 °C until complete coating failure. The positive effect of both types of Cr coatings was observed in all tests. Pre-damaged specimens showed only locally increased oxidation of the scratched zone, but no negative effects on the adjacent Cr coating. Finally, the behavior of the two types of coatings is compared and the degradation mechanisms are discussed based on hydrogen release data, extensive metallographic post-test examinations, and the current state of global research.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Irradiation creep measurement and microstructural analysis of chromium nitride–coated zirconium alloy using pressurized tubes

Environmental barrier coatings for Zr-based materials are currently under development to reduce oxidation and embrittlement in light-water reactors. Chromium nitride is one such candidate for this application, particularly as accident-tolerant fuel cladding. However, quantifying the impact of coatings on the irradiation-induced creep of zircaloy (Zry) is critical as this mechanism often exceeds thermal creep rates under light-water reactor operating conditions and can be a limiting design characteristic. Additionally, examining irradiation effects in the microstructure at the coating interface is key to understanding the compatibility of the material system. Here, to accelerate the experimental measurement of irradiation creep and microstructure evolution in CrN-Zry, compact, pressurized creep tubes were fabricated and irradiated in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory. Miniature, thin-walled rodlets fabricated from annealed Zr-Sn barstock were coated with CrN using physical vapor deposition (PVD) to nominal thicknesses of 4 and 8 μm. Coated and uncoated rodlet specimens were internally pressurized and welded, generating nominal circumferential hoop stresses of 0, 90, or 180 MPa under 300°C irradiation conditions. Twelve specimens were measured diametrically prior to irradiation using a low-cost, automated, contactless laser profilometer developed for this work. Specimens were irradiated in sealed capsules for one 25-day HFIR cycle, accumulating approximately 1.8 $\times$ 10 21 n/cm 2 fast fluence (E n > 10 MeV). The irradiated samples were retrieved and remeasured using the same profilometry system in a shielded hot cell facility. Irradiation creep between specimens was compared using standard statistical tests and showed that both thicknesses of CrN coating had a negligible effect on the irradiation creep strain of the Zry material. Microstructure characterization of pre- and post-irradiated CrN-Zry specimens showed minimal changes due to irradiation but did show a substantial O-rich region at the Zry-CrN interface.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Laser glazing of cold sprayed coatings for the mitigation of stress corrosion cracking in light water reactor (LWR) applications

The effect of laser power, traverse speed, and cold spray coating thickness were examined with the goal of mitigating and repairing stress corrosion cracking (SCC) in light water reactor (LWR) environment. For this purpose, SCC-susceptible Alloy 600 substrate material was coated with SCC-resistant Alloy 690 via the cold spray technique. The cold spray coated substrate was then laser-glazed using various laser parameters. Single pass and multiple pass laser glazed regions were created to determine the effects. For this purpose, the area of the fusion zone, depth of the fusion zone, and elemental composition of the cross section were examined by optical microscopy, scanning electron microscopy, and energy dispersive spectroscopy. Additionally, it was shown that chromium dilution from the laser glazed region into the substrate is not a significant factor in laser glazed cold spray coated samples. Separate laser glazed samples were subjected to ASTM 633C to determine coating adhesion. Finally, by using interrupted SCC crack growth rate tests, it was shown that low traverse speeds and high laser powers produce deep fusion zones within the cold sprayed coating and substrate that can be used to seal pre-existing cracks, thus stopping SCC growth.

36 MATERIALS SCIENCE↗