Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “chalcogenide”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

GaSb doping facilitates conduction band convergence and improves thermoelectric performance in n-type PbS

P-type lead chalcogenides have superior thermoelectric performance because they exhibit the energy convergence of several valence bands. However, despite the existence of two conduction bands, there has been no report about conduction band (CB) convergence for n-type counterparts because of the large energy difference between them. Therefore, new strategies are required to manipulate the CBs if enhancing the electrical transport performance of n-type lead chalcogenides is to be achieved. PbS is a highly attractive member of the lead chalcogenides because of its high earth-abundance and low cost. Here, we report that the introduction of GaSb can successfully dope the PbS matrix with Ga and Sb atoms occupying the Pb site in its rock salt structure. GaSb doping leads to conduction band convergence and enlarged effective density of state mass for n-type PbS. This effect results in superior power factor and decreased lattice thermal conductivity caused by the soft phonon modes and point defect scattering of phonons. Consequently, a record-high average power factor PF avg of ~20.4 μW cm –1 K –2 and figure of merit ZT avg of ~0.84 in the temperature range of 400 K to 923 K were obtained, higher than any n- and p-type PbS-based thermoelectric materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Discovery of a layered multiferroic compound Cu 1-x Mn 1+y SiTe 3 with strong magnetoelectric coupling

Multiferroic materials host both ferroelectricity and magnetism, offering potential for magnetic memory and spin transistor applications. Here, we report a multiferroic chalcogenide semiconductor Cu 1-x Mn 1+y SiTe 3 (0.04 ≤ x ≤ 0.26; 0.03 ≤ y ≤ 0.15), which crystallizes in a polar monoclinic structure (Pm space group). It exhibits a canted antiferromagnetic state below 35 kelvin, with magnetic hysteresis and remanent magnetization under 15 kelvin. We demonstrate multiferroicity and strong magnetoelectric coupling through magnetodielectric and magnetocurrent measurements. At 10 kelvin, the magnetically induced electric polarization reaches ~0.8 microcoulombs per square centimeter, comparable to the highest value in oxide multiferroics. We also observe possible room-temperature ferroelectricity. Given that multiferroicity is very rare among transition metal chalcogenides, our finding sets up a unique materials platform for designing multiferroic chalcogenides.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Alkali element (Li, Na, K, and Rb) doping of Cu 2 BaGe 1– x Sn x Se 4 films

Cu 2 BaGe 1–x Sn x Se 4 (CBGTSe) represents an exemplary system within the I 2 –II–IV–X 4 (I = Ag, Cu; II = Sr, Ba; IV = Ge, Sn; X = S, Se) family, which has been introduced to target suppressing the formation of anti-site defects and associated defect clusters within the analogous kesterite Cu 2 ZnSn(S,Se) 4 . Previous studies on CBGTSe films showed relatively low hole carrier densities (<10 13 cm –3 ), which may limit their corresponding application as active layers within photovoltaic, thermoelectric, and optoelectronic devices. In the current study, we explore the incorporation of alkali elements (Li, Na, K, and Rb) into CBGTSe films as prospective dopants to address the low hole carrier density and to allow for property tunability. First, incorporation of Na-, K-, and Rb-dopants noticeably increases the average grain sizes for CBGTSe films, while the Li-dopant has relatively limited impact. In addition, the alkali-dopants lead to a 1 to 3 orders of magnitude increase in hole carrier density (up to 10 15 cm –3 is achieved using K doping, corresponding to the alkali element yielding the highest doping efficiency). Here, the alkali-doped films show slightly lower minority carrier lifetimes and carrier mobility values than the non-doped samples, and these values are found to follow an approximate universal dependence with carrier density (also considering data derived from other previously explored vacuum-deposited I 2 –II–IV–X 4 chalcogenide films). As alkali-doping can significantly increase carrier densities, alkali elements can be considered useful p-type dopants for CBGTSe, as well as prospectively for other analogous I 2 –II–IV–X 4 systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Differences in Sb 2 Te 3 growth by pulsed laser and sputter deposition

High quality van der Waals chalcogenides are important for phase change data storage, thermoelectrics, and spintronics. Using a combination of statistical design of experiments and density functional theory, we clarify how out-of-equilibrium van der Waals epitaxial deposition methods can improve the crystal quality of Sb 2 Te 3 films. We compare films grown by radio frequency sputtering and pulsed laser deposition (PLD). The growth factors that influence the crystal quality for each method are different. For PLD grown films a thin amorphous Sb 2 Te 3 seed layer most significantly influences the crystal quality. In contrast, the crystalline quality of films grown by sputtering is rather sensitive to the deposition temperature and less affected by the presence of a seed layer. This difference is somewhat surprising as both methods are out-of-thermal-equilibrium plasma-based methods. Non-adiabatic quantum molecular dynamics simulations show that this difference originates from the density of excited atoms in the plasma. The PLD plasma is more intense and with higher energy than that used in sputtering, and this increases the electronic temperature of the deposited atoms, which concomitantly increases the adatom diffusion lengths in PLD. In contrast, the adatom diffusivity is dominated by the thermal temperature for sputter grown films. These results explain the wide range of Sb 2 Te 3 and superlattice crystal qualities observed in the literature. Finally, these results indicate that, contrary to popular belief, plasma-based deposition methods are suitable for growing high quality crystalline chalcogenides.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Thermally induced structural evolution and nanoscale interfacial dynamics in Bi-Sb-Te layered nanostructures

Layered chalcogenides, including Bi-Sb-Te ternary alloys and heterostructures, are renowned as thermoelectric and topological insulators and have recently been highlighted as plasmonic building blocks beyond noble metals. Here, we conduct joint in situ transmission electron microscopy and density functional theory calculations to investigate the temperature-dependent nanoscale dynamics and interfacial properties, identifying the role of native defects and edge configurations in the anisotropic sublimation of Bi 2 Te 3 -Sb 2 Te 3 heterostructures and Sb 2-x Bi x Te 3 alloys. We report structural dynamics, including edge evolution, layer-by-layer sublimation, and the formation and coalescence of thermally induced polygonal nanopores. These nanopores are initiated by preferential dissociation of tellurium, reducing thermal stability in heterostructures. Triangular and quasi-hexagonal configurations dominate nanopore structures in heterostructures. Our calculations reveal antisite defects (Te Sb and Te Bi ) as key players in defect-assisted sublimation. These findings enhance our understanding of nanoscale dynamics and assist in designing tunable low-dimensional chalcogenides.

Bi2Te3-Sb2Te3 heterostructure↗
DOE OSTI2023

Structure-thermal property relationships of aikinite PbCuBiS 3

Understanding the structural properties and chemical bonding in complex multinary chalcogenides is highly valuable, as it provides vital information for controlling their physical properties to suit various technological applications. Here, we report on the structural, thermal, and electronic properties of PbCuBiS 3 by incorporating an experimental and theoretical investigation of this material. Analysis of the experimental temperature-dependent heat capacity and thermal conductivity data show that weak bonding and strong lattice anharmonicity give rise to ultralow thermal conductivity. Chemical bonding information obtained from the density functional theory electronic calculations reveal significant antibonding interactions that underscore the dominant role of the Cu-S tetrahedra on occupied antibonding states, as well as a highly distorted Pb/Bi-S environment inducing weak bonding and strong lattice anharmonicity. This study broadens our understanding of the structure-property relationships for this material, and can be useful for developing this and similar chalcogenide materials for potential applications of interest.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Amine-Thiol/Selenol Chemistry for Efficient and Stable Perovskite Solar Cells

Controlling the crystallization of perovskites is imperative to reduce defect densities in perovskite thin films and extend device lifetimes. In this work, combinations of amine and chalcogenide ligands were introduced in the sequential deposition method to fabricate highly crystalline and orientated formamidinium lead iodide thin films with reduced defect densities and increased charge carrier lifetimes. The dual additives can tune the perovskite intermediate state and control the crystallization leading to devices with improved efficiencies and stabilities. While thiophenol failed to prevent the amine ligand from degrading the perovskite precursors, benzene selenol combinations with amine-ligands drastically changed the solution chemistry to increase the PbI 2 conversion to highly crystalline and orientated α-FAPbI 3 films with lower defect densities. X-ray photoelectron spectroscopy studies reveal benzene selenol evaporates from the thin film leaving behind a modified surface, which is associated with the amine additive. These results indicate the amine selection can be used to tune the surface properties. Lastly, we propose a highly tunable I 2 reduction strategy using chalcogenide chemistry to help enable the realization of perovskite solar cells with high performance and stability.

defects↗
DOE OSTI2022

Transuranium Sulfide via the Boron Chalcogen Mixture Method and Reversible Water Uptake in the NaCu T S 3 Family

The behavior of 5f electrons in soft ligand environments makes actinides, and especially transuranium chalcogenides, an intriguing class of materials for fundamental studies. Due to the affinity of actinides for oxygen, however, it is a challenge to synthesize actinide chalcogenides using non-metallic reagents. Using the Boron Chalcogen Mixture (BCM) method, we achieved the synthesis of the transuranium sulfide NaCuNpS 3 starting from the oxide reagent, NpO 2 . Via the same synthetic route, the isostructural composition of NaCuUS 3 was synthesized and the material contrasted with NaCuNpS 3 . Single crystals of the U-analog, NaCuUS 3 , were found to undergo an unexpected reversible hydration process to form NaCuUS 3 ·xH 2 O (x ≈ 1.5). Here, a large combination of techniques was used to fully characterize the structure, hydration process, and electronic structures, specifically a combination of single crystal, powder, high temperature powder X-ray diffraction, extended X-ray ab-sorption fine structure, infrared, and inductively coupled plasma spectroscopies, thermogravimetric analysis, and density functional theory calculations. The outcome of these analyses enabled us to determine the composition of NaCuUS 3 ·xH 2 O and obtain a structural model that demonstrated the retention of the local structure within the [CuUS 3 ] – layers throughout the hydration-dehydration process. Band structure, density of states, and Bader charge calculations for NaCuUS 3 , NaCu-US 3 ·xH 2 O, and NaCuNpS 3 along with X-ray absorption near edge structure, UV-vis-NIR and work function measurements on ACuUS 3 (A = Na, K, and Rb) and NaCuUS 3 ·xH 2 O samples were carried out to demonstrate that electronic properties arise from the [CuTS 3 ] – layers and show surprisingly little dependence on the interlayer distance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Pressure-tuned plethora of ferroelectric phases in CuInP 2 S 6

Layered chalcogenides like CuInP 2 S 6 are room temperature ferroelectrics. Modest compression even increases the electric polarization, raising questions about the origin of this unusual trend and other properties under pressure. In this work, we combine synchrotron-based infrared and Raman scattering spectroscopies, x-ray diffraction, and resistivity measurements with first-principles calculations of the lattice dynamics and energy landscape to unravel the influence of pressure on symmetry, polarization, and metallicity. We uncover a remarkable series of phase transitions across a series of polar space groups: monoclinic Cc → trigonal P31c (prismatic sulfur) → P31c (octahedral sulfur). True metallicity develops above 63 GPa, significantly higher than in related MPS 3 materials (M = Mn, Co, Fe, Ni), offering a picture of competing states of matter that is different than previously supposed. Detailed examination of pressure trends within the Cc phase also reveals phonon lifetime changes and streaking of satellite x-ray peaks that correlate with the maximum polarization. We discuss these tendencies in terms of Cu + ion migration, phase formation, and the overall energy landscape. Our findings place the high pressure behavior of CuInP 2 S 6 on a firm foundation and pave the way for the development of structure-property relations in this family of complex chalcogenides.

ferroelectric phases↗
DOE OSTI2021

Optoelectronic property comparison for isostructural Cu 2 BaGeSe 4 and Cu 2 BaSnS 4 solar absorbers

To target mitigation of anti-site defect formation in Cu 2 ZnSnS 4–x Se x , a new class of chalcogenides, for which Ba or Sr (group 2) replace Zn (group 12), has recently been introduced for prospective solar absorber application. Cu 2 BaGeSe 4 (CBGSe) and Cu 2 BaSnS 4 (CBTS) are two such compounds, which share a common trigonal crystal structure (P3 1 space group) and similar quasi-direct band gap (~2 eV). While CBTS-based films have already been studied, there are no reports yet on films and solar cells based on related CBGSe. To identify key differences and similarities in the electronic properties between these two materials, electronic characteristics (e.g., carrier concentration, mobility, electron affinity, defect levels, recombination, and charge carrier kinetics) of vacuum-deposited CBGSe and CBTS films are compared using a variety of characterization methods. Hall effect measurements reveal that CBGSe films have relatively higher hole carrier concentration and lower mobility (3 × 10 15 cm –3 , 0.6 cm 2 V –1 s –1 ) compared to CBTS (5 × 10 12 cm –3 , 3.5 cm 2 V –1 s –1 ). Photoelectron spectroscopy yields low electron affinity values for both CBGSe (3.7 eV) and CBTS (3.3 eV), pointing to the necessity of pursuing low electron affinity buffer materials for both types of absorbers. At low temperatures, CBGSe films show free-exciton photoluminescence, as well as pronounced deep-level emission at ~1.4 eV, while CBTS films exhibit a strong bound-exciton signal with noticeably less intense deep-level emission than for CBGSe. Charge carrier kinetics, transport, and recombination properties of both types of films are also analyzed using optical-pump terahertz-probe spectroscopy and time-resolved microwave conductivity. The first CBGSe prototype solar cells (using chemical bath deposited CdS as a buffer layer) show a maximum of 1.5% efficiency with ~0.62 V open-circuit voltage. Furthermore, the measured properties point to possible limiting factors for CBGSe and related films for PV and optoelectronics and provide insights on possible approaches for improvement within this multinary chalcogenide family.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Pressure Evolution of Ultrafast Photocarrier Dynamics and Electron–Phonon Coupling in FeTe 0.5 Se 0.5

Understanding the coupling between electrons and phonons in iron chalcogenides FeTe x Se 1–x has remained a critical but arduous project in recent decades. The direct observation of the electron–phonon coupling effect through electron dynamics and vibrational properties has been lacking. Here, we report the first pressure-dependent ultrafast photocarrier dynamics and Raman scattering studies on an iron chalcogenide FeTe 0.5 Se 0.5 to explore the interaction between electrons and phonons in this unconventional superconductor. The lifetime of the excited electrons evidently decreases as the pressure increases from 0 to 2.2 GPa, and then increases with further compression. The vibrational properties of the A 1g phonon mode exhibit similar behavior, with a pronounced frequency reduction appearing at approximately 2.3 GPa. The dual evidence reveals the enhanced electron–phonon coupling strength with pressure in FeTe 0.5 Se 0.5 . Our results give an insight into the role of the electron–phonon coupling effect in iron-based superconductors.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1995

Preparation of Thermoelectric Materials From Melts

A review of melt preparation techniques is presented covering necessary phase relationships, synthesis/alloying and crystal growth of thermoelectric materials. The processes described require the knowledge of composition-temperature or composition- temperature-pressure phase diagrams. This knowledge enables the selection of the appropriate method of preparation, apparatus design and processing. The materials, from a technological point of view, will be roughly divided into three categories: low temperature materials (group V chalcogenides based on Bi2Te3), middle temperature materials (group IV chalcogenides based on PbTe) and high temperature materials (Si-Ge solid solutions). All known methods of preparation from melts are described, and a comparative analysis is given. (complete abstract)

thermoelectrics↗
DOE OSTI2026

Structural, Electronic, and Photophysical Insights into a Few Atom Copper-Sulfur Cluster in the Solid and Solution States

Coinage-metal chalcogenide clusters are widely studied for their attractive photoluminescence properties. Copper chalcogenides are especially promising, but are often confined to solid-state investigations due to their limited solution stability and the difficulty of synthesizing stable, well-defined clusters. Here, we investigate copper–sulfur clusters incorporating a small number of Cu atoms to elucidate fundamental atomic interactions, ground- and excited-state characteristics, and photophysical behavior in both solid and solution. We have synthesized the Cu6(4,6-dimethyl-2-mercaptopyrimidine)6 cluster in both neutral and charged states, Cu6 and Cu6-2H2+, respectively, by selective ligand protonation. The molecular structures are determined using single-crystal X-ray diffraction, while Cu K-edge X-ray absorption spectroscopy is used to probe Cu electronic structure differences arising from the ligand modification. Steady-state and pump-probe optical spectroscopy is used to investigate photophysical properties, interpreted using density functional theory methods. Both clusters exhibit good stability in the solid state and in solution and show characteristic near-infrared emission with microsecond lifetimes. Overall, the Cu6S6 clusters display favorable charge–transfer characteristics and show potential for further use in driving photochemical transformations.

Copper-sulfur clusters↗
DOE OSTI2022

High-performance and stable AgSbTe 2 -based thermoelectric materials for near room temperature applications

AgSbTe 2 -based ternary chalcogenides show excellent thermoelectric performance at low- and middle-temperature ranges, yet their practical applications are greatly limited by their intrinsic poor thermodynamic stability. In this work, we demonstrate that AgSbTe 2 -based ternary chalcogenides can be stabilized for service below their decomposition threshold. A series of Ag x Sb 2-x Te 3-x (x = 1.0, 0.9, 0.8 and 0.7) samples have been prepared by the melt-quenching method. Among them, phase pure Ag 0.9 Sb 1.1 Te 2.1 is verified by comprehensive structural characterizations from macroscale by X-ray diffraction to microscale by energy-dispersive spectroscopy and then to sub-nanometer scale by atom probe tomography. This composition is further chosen for the stability investigation. The decomposition threshold of Ag 0.9 Sb 1.1 Te 2.1 appears around 473K. Below this temperature, the chemical compositions and thermoelectric properties are barely changed even after 720 h annealing at 473 K. The figure-of-merit (zT) value of Ag 0.9 Sb 1.1 Te 2.1 below the decomposition threshold is very competitive for real applications even compared with Bi 2 Te 3 -based alloys. The average zT of Ag 0.9 Sb 1.1 Te 2.1 at 300–473 K reaches 0.84, which is higher than most other thermoelectric materials in a similar temperature range, promising applications in miniaturized refrigeration and power generation near room temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Off-stoichiometric semiconductors Cu 1.33+x Zn 1.33-x In 1.33 Se 4 (x = 0, 0.1, 0.2 and 0.3): Synthesis, structure, and thermal and electrical properties

The synthesis, structure, and temperature dependent thermal and electrical properties of off-stoichiometric polycrystalline modified zinc blende quaternary chalcogenides Cu 1.33+x Zn 1.33-x In 1.33 Se 4 , where x = 0, 0.1, 0.2 and 0.3, are investigated. Temperature-dependent electrical properties reveal these compositions to be semiconductors with alteration of the carrier concentration and electrical transport via stoichiometric variation. The thermal conductivity is low for all specimens and intrinsic to these materials. First principles calculations are also reported in establishing a fundamental investigation that illustrates the large variation in stoichiometry that is possible in these materials. This stoichiometric variation results in the observed variation of the transport properties. Overall, the results presented reveal fundamental structure-property relationships in these quaternary chalcogenides, and provides a basis for further research into the viability for large stoichiometric variation in other materials that are of interest for technological applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Engineering the fracture resistance of 2H-transition metal dichalcogenides using vacancies: An in-silico investigation based on HRTEM images

Vacancy engineering of 2H-transition metal dichalcogenides (2H-TMDs) has recently attracted great attention due to its potential to fine-tune the phonon and opto-electric properties of these materials. From a mechanical perspective, this symmetry-breaking process typically reduces the overall crack resistance of the material and adversely affects its reliability. However, vacancies can trigger the formation of heterogeneous phases that synergistically improve fracture properties. In this study, using MoSe2 as an example, we characterize the types and density of vacancies that can emerge under electron irradiation and quantify their effect on fracture. Molecular dynamic (MD) simulations, employing a re-parameterized Tersoff potential capable of accurately capturing bond dissociation and structural phase changes, reveal that isolated transition metal monovacancies or chalcogenide divacancies tend to arrest the crack tip and hence enhance the monolayer toughness. In contrast, isolated chalcogenide monovacancies do not significantly affect toughness. The investigation further reveals that selenium vacancy lines, formed by high electron dose rates, alter the crack propagating direction and lead to multiple crack kinking. Using atomic displacements and virial stresses together with a continuum mapping, displacement, strain, and stress fields are computed to extract mechanistic information, e.g., conditions for crack kinking and size effects in fracture events. The study also reveals the potential of specific defect patterns, “vacancy engineering,” to improve the toughness of 2H-TMDs materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Transforming the electronic properties of phosphorene through charge transfer superatomic doping

Phosphorene is a two-dimensional electron poor p-type semiconductor with great promise for applications in electronics and optoelectronics. Here, in this work, we propose how the two most important properties of a semiconductor, the band gap energy and the nature of carriers, can be controlled by changing the dimensionality or through charge transfer doping with metal-chalcogenide superatoms. Our studies on nanoribbons examine how the band gap can be changed by controlling the width of the ribbons. We investigate the stability and properties of bare and H-terminated nanoribbons. We show that small non-passivated ribbons can be metallic while the passivated ribbons show variation in the band gap energy as a function of the width of the ribbon. We next investigate an alternative approach to band gap and carrier control via doping with ligated metal-chalcogenide superatom clusters whose redox properties can be changed by ligand exchange. Our results obtained from deposition of Co 6 S 8 (PH 3 ) 5-n (CO) n clusters on a phosphorene support showed that the band gap energy can be controlled by exchanging the electron donating phosphine ligands with electron withdrawing CO. We then show that by depositing Re 6 Se 8 (PH 3 ) 5-n Cl n clusters, phosphorene can be converted into a p- or n- type semiconductor as the relative composition of ligands is changed. Our studies provide a novel approach to controlling carrier type and band gap in phosphorene.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Thermal Evolution of Internal Strain in Doped PbTe

Recent improvements in the efficiency of heat-to-electricity energy conversion in lead chalcogenide thermoelectrics involve reducing the thermal conductivity by incorporating large amounts of internal strain. The extent to which typical lead chalcogenide processing techniques (such as doping, ball milling, and densification) increase internal strain and dislocation density must be quantified to improve materials design. In this study, neutron powder diffraction is leveraged to evaluate the internal strain introduced by ball milling in doped and undoped powders. Doping with Na and/or Eu increases internal strain beyond ball milling alone, with the greatest increase from combining the two dopants. Strain recovery occurs in each powder above 400 K but can be suppressed by co-doping, indicating a strong dopant–dislocation interaction in this system. Therefore, high-temperature processing of PbTe powders should be avoided if high internal strain is desired. Low-temperature densification and/or rapid pressing techniques may be key to maintaining internal strain in the final pressed pellet. The diffraction peak asymmetry and correlated elastic softening measured in pressed PbTe pellets in past studies were not observed in the precursor powders measured here, suggesting that measurements of the Debye temperature on final pressed pellets are required to examine the influence of defect-induced elastic softening on thermal conductivity. This work provides key guidance for defect engineering to maximize internal strain and thermoelectric performance in PbTe thermoelectrics.

36 MATERIALS SCIENCE↗