Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “bulk modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Strain engineered pyrochlore at high pressure

Strain engineering is a promising method for next-generation materials processing techniques. Here, we use mechanical milling and annealing followed by compression in diamond anvil cell to tailor the intrinsic and extrinsic strain in pyrochlore, Dy 2 Ti 2 O 7 and Dy 2 Zr 2 O 7 . Raman spectroscopy, X-ray pair distribution function analysis, and X-ray diffraction were used to characterize atomic order over short-, medium-, and long-range spatial scales, respectively, under ambient conditions. Raman spectroscopy and X-ray diffraction were further employed to interrogate the material in situ at high pressure. High-pressure behavior is found to depend on the species and concentration of defects in the sample at ambient conditions. Overall, we show that defects can be engineered to lower the phase transformation onset pressure by ~50% in the ordered pyrochlore Dy 2 Zr 2 O 7 , and lower the phase transformation completion pressure by ~20% in the disordered pyrochlore Dy 2 Zr 2 O 7 . These improvements are achieved without significantly sacrificing mechanical integrity, as characterized by bulk modulus.

36 MATERIALS SCIENCE↗

X-Ray Diffraction and Electron Microscopy Studies of the Size Effects on Pressure-Induced Phase Transitions in CdS Nanocrystals

In recent years, investigations of the phase transition behavior of semiconducting nanoparticles under high pressure has attracted increasing attention due to their potential applications in sensors, electronics, and optics. However, current understanding of how the size of nanoparticles influences this pressure-dependent property is somewhat lacking. In particular, phase behaviors of semiconducting CdS nanoparticles under high pressure have not been extensively reported. Therefore, in this work, CdS nanoparticles of different sizes are used as a model system to investigate particle size effects on high-pressure-induced phase transition behaviors. In particular, 7.5, 10.6, and 39.7 nm spherical CdS nanoparticles are synthesized and subjected to controlled high pressures up to 15 GPa in a diamond anvil cell. Analysis of all three nanoparticles using in-situ synchrotron wide-angle X-ray scattering (WAXS) data shows that phase transitions from wurtzite to rocksalt occur at higher pressures than for bulk material. Bulk modulus calculations not only show that the wurtzite CdS nanomaterial is more compressible than rocksalt, but also that the compressibility of CdS nanoparticles depends on their particle size. Furthermore, sintering of spherical nanoparticles into nanorods was observed for the 7.5 nm CdS nanoparticles. Our results provide new insights into the fundamental properties of nanoparticles under high pressure that will inform designs of new nanomaterial structures for emerging applications.

Meng, Lingyao↗

Experimental verification of the high pressure crystal structures in NH{sub 3}BH{sub 3}

A detailed high-pressure study on NH{sub 3}BH{sub 3} has been carried out using in situ synchrotron X-ray diffraction (XRD) and Raman scattering with a diamond anvil cell up to 20 and 33 GPa, respectively. The Rietveld refinement based on the XRD pattern and analysis of Raman data indicate two first-order phase transitions from the ambient pressure I4 mm structure (α-NH{sub 3}BH{sub 3}) to a high pressure Cmc2{sub 1} phase (β-NH{sub 3}BH{sub 3}) at 2.14 GPa, and further into a monoclinic P2{sub 1} (Z = 2) phase (γ-NH{sub 3}BH{sub 3}) at 9.67 GPa. Fitting the measured volumetric compression data to the third order Birch-Murnaghan equation of state reveals a bulk modulus of B{sub 0} = 9.9 ± 0.5 and 17.0 ± 3.0 GPa (with fixed B{sub 0}{sup ′} = 4) for the β-NH{sub 3}BH{sub 3} below and above 5 GPa, respectively. Still, with the splitting of the NBH rock mode in Raman experiment, it is concluded that a second-order isostructural phase transition occurs at 5 GPa. By analyzing the dihydrogen bonding framework, the origin of the isostructural phase transition is attributed to the number of dihydrogen bondings per molecule in the Cmc2{sub 1} phase increasing from 12 to 14 at 5 GPa.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

First evidence of P2{sub 1}/n to P2{sub 1}/c structural transformation in pyroxene-type LiAlGe{sub 2}O{sub 6} under high-pressure conditions

The high-pressure behavior of the pyroxene-type compound LiAlGe{sub 2}O{sub 6}, the unique representative of a P2{sub 1}/n-pyroxene, was investigated by in-situ X-ray diffraction and Raman spectroscopy on single-crystal samples hydrostatically pressurized in a diamond-anvil cell. The structure was found to undergo a first-order phase transition on compression, with a critical transition at 5.23±0.02 GPa. Together with a strong volume discontinuity of −ΔV/V{sub 0}=−4.1% the transition shows a remarkable hysteresis loop over at least 0.70 GPa pressure interval. The bulk modulus of the low- and high-pressure polymorphs corresponds to K{sub 0}=114(1) and 123(2) GPa, respectively, as described by a 2{sup nd} order Birch–Murnaghan equation of state. Based on the systematic extinctions the transition was identified as a P2{sub 1}/n-to-P2{sub 1}/c transformation. The mechanism of structural transformation was identified to be controlled by the stereochemistry of the Li atoms at the M2 site, which changes its coordination number from 5 to 6. The formation of new Li–O bonds involves the co-operative folding of Ge{sub 2}O{sub 6}-chains, which explains the anisotropy of axial elasticities and the spontaneous strain across the transformation. Simultaneously the distortion correction of AlO{sub 6} units associated with the transition further explains the preference of the P2{sub 1}/c structure under pressure. - Graphical abstract: Detail of the crystal structures of LP-LAG at 3.48 GPa (left) and HP-LAG at 4.51 GPa (right). Li on M2 are green; AlO{sub 6} octahedra (Al at M1) are orange; tetrahedra sites in LP-LAG: T1 (yellow) and T2 (blue); tetrahedra sites in HP-LAG: A-chains (yellow), B-chains (blue). - Highlights: • A new high-pressure phase transition P2{sub 1}/n–P2{sub 1}/c was found for LaAlGe{sub 2}O{sub 6}. • The transition was also followed by micro-Raman spectroscopy. • The high-pressure polymorph shows a higher bulk modulus. • The structural evolution of the two symmetries was determined.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

ORNL_AISD_NiNb

This dataset describes the nickel-niobium solid solution binary alloy, where the two constituent elements nickel (Ni) and niobium (Nb) are randomly placed on an underlying crystal lattice. This dataset for nickel-niobium (Ni-Nb) alloys available includes the formation energy and bulk modulus for each crystal structure. Each atomic sample has a disordered phase which is obtained starting from an initial regular crystal structure of type body-centered cubic (BCC), face-centered cubic (FCC), or hexagonal compact packed (HCP). The geometry optimization ensures that all the alloy samples reached the equilibrium with negative formation energy. We perform geometry optimizations using the LAMMPS simulation package [1], a flexible simulation tool for particle-based materials modeling at the atomic, meso, and continuum scales. We utilized the embedded atom model (EAM) potential for Ni and Nb developed in a previous study [2]. The potential could describe behaviors of the liquid and solid phases of Ni-Nb alloy. The structural factors and angular distributions of three atoms are well-matched with X-ray and ab initio-based molecular dynamics data. We prepared the three different crystals with different initial lattice parameters (3.52 Ã… for FCC, 3.32 Ã… for BCC, and 3.5 Ã… for HCP). We performed energy minimization in two steps. Firstly, we minimized the structures with an isotropic unit cell to minimize the side effects from our arbitrary lattice parameters for all other compositions. Then, we applied geometry optimization with a triclinic (non-orthogonal) unit cell to fully minimize the stress components to calculate the elastic constants. In this procedure, we chose 10,000 as the maximum number of allowable steps aimed at obtaining fully relaxed atomic geometries. The dataset consists of three sets of crystal structures. The first set contains 46,086 irregular crystal structures, each of them with 54 atoms, obtained through optimization starting from a regular BCC crystal structure. The second set contains 24,543 irregular crystal structures, each of them with 32 atoms, obtained through optimization starting from a regular FCC crystal structure. The third set contains 39,303 irregular crystal structures, each of them with 48 atoms, obtained through optimization starting from a regular HCP crystal structure. The atomic configurations within each set span the possible compositional range. The three sets have been unified in a global dataset, which is extremely heterogeneous in terms of crystal structures, lattice volumes, and atomic configurations. Organization of files inside the dataset: the dataset contains three subdirectories called • BCC_opt • FCC_opt • HCP_opt based on the type of initial regular structure used to start the geometry optimization. Inside each of these folders, every atomic structure is identified by a string “A_B_Câ€, where A denotes the number of Nb in the system, B denotes index of structure with a given Nb number, and C denotes the total number of structures generated with a given Nb number. For each optimized crystal structure identified by the unique string of characters “A_B_Câ€, three files are provided: • A_B_C_opt.xyz: The optimized geometries in xyz format • A_B_C_opt.cfg: The optimized geometries in cfg format. It includes cell information and atomic energy, and forces calculated from LAMMPS. • A_B_C.elastic: Raw data of 21 elastic constants from LAMMPS output. • A_B_C.bulk: Calculated upper and lower bounds of bulk modulus and averaged one based on Voigt-Reuss-Hill approach from *.elastic. References: [1] A. P. Thompson, H. M. Aktulga, R. Berger, D. S. Bolintineanu, W. M. Brown, P. S. Crozier, P. J. in 't Veld, A. Kohlmeyer, S. G. Moore, T. D. Nguyen, R. Shan, M. J. Stevens, J. Tranchida, C. Trott, and S. J. Plimpton. LAMMPS - a flexible simulation tool for particle-based materials modeling at the atomic, meso, and continuum scales. Comp. Phys. Comm., 271:108171, 2022. [2] Y Zhang, R Ashcraft, MI Mendelev, CZ Wang, and KF Kelton. Experimental and molecular dynamics simulation study of structure of liquid and amorphous ni62nb38 alloy. The Journal of chemical physics, 145(20):204505, 2016.

36 MATERIALS SCIENCE↗

Radiation-damage-induced transitions in zircon: Percolation theory applied to hardness and elastic moduli as a function of density

Two in literature predicted percolation transitions in radiation-damaged zircon (ZrSiO 4 ) were observed experimentally by measurement of the indentation hardness as a function of density and their correlation with the elastic moduli. Percolations occur near 30% and 70% amorphous fractions, where hardness deviates from its linear correlation with the elastic modulus ( E ), the shear modulus ( G ) and the bulk modulus ( K ). Finally, the first percolation point p c1 generates a cusp in the hardness versus density evolution, while the second percolation point is seen as a change of slope.

36 MATERIALS SCIENCE↗

Anomalous compressive behavior in CeO[subscript 2] nanocubes under high pressure

High-pressure angle-dispersive x-ray diffraction measurements have been performed on bulk and nanocrystalline cubic CeO{sub 2} with mean sizes of 4.7 and 5.6 nm. It is found that the compressibility of the nanocrystals is lower than the bulk when a threshold pressure is reached. This critical pressure is found to be 10 GPa for 4.7 nm and 16 GPa for 5.6 nm CeO{sub 2} nanocubes. The particle size dependence of the threshold pressure for the hardening of CeO{sub 2} nanoparticles is quite unusual. First-principles electronic calculations show that the increased bulk modulus of the nanocrystal is due to the strengthening of the surface Ce-O bonds resulting in a much larger shear modulus than in the bulk and consequently hardening the shell surface.

36 MATERIALS SCIENCE↗

First-principles study on structural mechanical and thermodynamic properties of HfMoTaTiZr

This study calculates the phase diagram of HfMoTaTiZr using the TCHEA1 database in Thermo-Calc software. Furthermore, it also investigates the structural and mechanical properties of HfMoTaTiZr by applying first-principles calculations. The elastic and other mechanical properties such as Young’s modulus, pugh ratio, hardness, bulk modulus was derived and discussed. These parameters were found to be in good harmony with previously available experimental reports. Vickers hardness of HfMoTaTiZr predicted from the Tians model agrees with the available experimental result. This study also investigates the thermal coefficient of linear expansion and vibrational heat capacity of the HfMoTaTiZr using the Debye–Grüneisen theory.

36 MATERIALS SCIENCE↗

Analysis of differential scanning calorimetry data for aged plutonium

Differential scanning calorimetry data for samples of a 52 year old plutonium alloy with 3.3 at. % Ga that were heated beyond the melting point is analyzed using transition state theory to find activation energies for the δ to ε and ε to liquid phase transitions. A Bayesian statistical method involving a Gaussian process model is used to find mean values and confidence intervals for the activation energies. The activation energy for the δ to ε phase transition increases by 3.3 ± 3.8% per decade, relative to the case when all age related plutonium lattice point defects have been removed through annealing. The corresponding increase in activation energy for the ε to liquid transition is shown to be 7.1 ± 1.8% per decade. It is postulated that the change in activation energy with age for both phase transitions is caused, in part, by the accumulation of the same type of lattice point defects associated with the observed increase in elastic bulk modulus over time.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Static analysis of a sonar dome rubber window

The application of NASTRAN (level 16.0.1) to the static analysis of a sonar dome rubber window (SDRW) was demonstrated. The assessment of the conventional model (neglecting the enclosed fluid) for the stress analysis of the SDRW was made by comparing its results to those based on a sophisticated model (including the enclosed fluid). The fluid was modeled with isoparametric linear hexahedron elements with approximate material properties whose shear modulus was much smaller than its bulk modulus. The effect of the chosen material property for the fluid is discussed.

Lai, J. L.↗

Crystallite-size dependency of the pressure and temperature response in nanoparticles of magnesia

We have carefully measured the hydrostatic compressibility and thermal expansion for a series of magnesia nanoparticles. We found a strong variance in these mechanical properties as crystallite size changed. For decreasing crystallite sizes, bulk modulus first increased, then reached a modest maximum of 165 GPa at an intermediate crystallite size of 14 nm, and then decreased thereafter to 77 GPa at 9 nm. Thermal expansion, meanwhile, decreased continuously to 70% of bulk value at 9 nm. These results are consistent to nano-ceria and together provide important insights into the thermal-mechanical structural properties of oxide nanoparticles.

36 MATERIALS SCIENCE↗

Symmetries of the Gas Dynamics Equations using the Differential Form Method

Here, a brief review of the theory of exterior differential systems and isovector symmetry analysis methods is presented in the context of the one-dimensional inviscid compressible flow equations. These equations are formulated as an exterior differential system with equation of state (EOS) closure provided in terms of an adiabatic bulk modulus. The scaling symmetry generators—and corresponding EOS constraints—otherwise appearing in the existing literature are recovered through the application and invariance under Lie derivative dragging operations.

97 MATHEMATICS AND COMPUTING↗

Au-Ag Alloy Static High Pressure EOS measurements: FY09 summary of results

Static high-pressure measurements of the equation of state of a Gold-Silver alloy (23.5 wt-% Ag) at room temperature were performed up to a pressure of approximately 100 GPA (1 megabar). Measurements were made using an energy-dispersive x-ray diffraction method. The data was analyzed, yielding crystal structure lattice constants and volume/density as a function of pressure. The results are extremely precise yielding accuracy of better than 1%. The experiments were carried out at the HPCAT 16BM-D beamline at the Advanced Photon Source. Two experiments on separate samples were carried out using conventional membrane diamond anvil cells. To achieve hydrostatic conditions, we loaded a 50-100 micron piece of the Au-Ag alloy into the cell and surrounded it with neon and mineral oil pressure media in the respective experiments. The differing pressure media demonstrated no measurable difference on the resultant crystal structures, lattice constants or pressure-volume curves. Results of our work are shown in the figures below. Up to the maximum pressure of 100 GPa the sample remained in the face-centered cubic structure, e.g., we observed no change in crystal structure. EOS curves of silver and gold, taken from the literature, are shown for comparison. We fit our data to a Vinet EOS functional form, and the parameters for this EOS were found to be, Reference (ambient pressure) volume, V{sub 0} = 16.965435 {angstrom}{sup 3}; Reference (ambient pressure) density, {rho}{sub 0} = 16.14584 g/cm{sup 3}; Bulk Modulus, K{sub 0} = 144 GPa; and Bulk Mod Derivative, K{prime}{sub 0} = 5.66. As one might expect the Au-Ag alloy lies between the gold and silver EOS curves, and tracks more closely to the gold EOS. These data are useful in validating and developing predictive EOS models of the pressure-dependent behavior of Au-Ag alloys.

36 MATERIALS SCIENCE↗

Mechanical and Thermal Properties for Uranium and U–6Nb Alloy from First-Principles Theory

Elasticity, lattice dynamics, and thermal expansion for uranium and U–6Nb alloy (elastic moduli) are calculated from density functional theory that is extended to include orbital polarization (DFT+OP). Introducing 12.5 at.% of niobium, substitutionally, in uranium softens all the cii elastic moduli, resulting in a significantly softer shear modulus (G). Combined with a nearly invariant bulk modulus (B), the quotient B/G increases dramatically for U–6Nb, suggesting a more ductile material. Lattice dynamics from a harmonic model coupled with a DFT+OP electronic structure is applied for α uranium, and the obtained phonon density of states compares well with inelastic neutron-scattering measurements. The Debye temperature associated with the lattice dynamics falls within the range of experimentally observed Debye temperatures and it also validates our quasi-harmonic (QH) phonon model. The QH Debye–Grüneisen phonon method is combined with a DFT+OP electronic structure and used to explore the anisotropic thermal expansion in α uranium. The anomalous negative thermal expansion (contraction) of the b lattice parameter of the α-phase orthorhombic cell is relatively well reproduced from a free-energy model consisting of QH-phonon and DFT+OP electronic structure contributions.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Design and Development of Novel Equiatomic Refractory Multi Principal elemental Alloys Based on MoNbTi System for Use in Irradiation Environments

Multi Principal Elemental Alloys (MPEA) have emerged as promising materials for next-generation nuclear reactors due to their exceptional irradiation resistance. Eight equiatomic MPEA based on the MoNbTi system, comprising of elements with low thermal neutron absorption cross-sections were explored using a combined approach employing empirical parameter estimations, and CALPHAD simulations by which the phases and elemental segregation observed in all the alloys in the as-cast state were predicted. Solution heat treatment at 1500°C transformed five alloys into single-phase matrix materials, enhancing homogeneity and reducing hardness. The densities of the alloys ranged between 6.47 to 7.68 g/cm3, hardness between 472 and 656 VHN, Young’s modulus between 142 GPa to 169 GPa, shear modulus between 54 GPa and 62 GPa, bulk modulus between 117 GPa to 194 GPa and Poisson’s ratio between 0.3 to 0.35. The in-situ high temperature Xray diffraction results, differential scanning calorimetry and dilatometry results up to 1000°C suggested the high temperature phase stability of the MPEA. Subsequent ageing heat treatment at 800 and 1000 oC for 96 hours revealed significant secondary phase precipitation in MoNbTiZr, MoNbTiZrV, and MoNbTiCrA. Oxidation studies at 800 oC for 24 hours in air revealed superior oxidation resistance and cubic rate law dependence in Cr containing MPEA especially in MoNbTiCrAl, while severe mass gain resulting in total disintegration and exfoliation in MoNbTiZr and MoNbTiZrV. This comprehensive study underscores the potential of novel MPEA as promising materials for advanced nuclear reactor applications, shedding light on their microstructural control, mechanical properties, thermal stability, and oxidation resistance.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗