Results for “average atom” — Page 14

NASA NTRS1991

Molecular Dynamics study of Pb overlayer on Cu(100)

Isothermal-isobaric Molecular Dynamics (MD) simulation of a submonolayer Pb film in c(2x2) ordered structure adsorbed on a Cu(100) substrate showed retention of order to high T. The Embedded Atom Method (EAM) calculated the energy of atoms of overlayer and substrate. The time-averaged squared modulus of the two dimensional structure factor for the Pb overlayer measured the order of the overlayer. The results are for increasing T only, and require verification by simulated cooling.

Karimi, M.↗

NASA NTRS1994

Voyager measurements of the isotopic composition of cosmic-ray aluminum and implications for the propagation of cosmic rays

We report a new measurement of the cosmic-ray isotopic composition of aluminum in the low-energy range form 75 to 206 MeV per nucleon.This measurement was made using the high-energy telescope of the CRS experiment on the Voyager 1 and 2 spacecraft during the time period from 1977 to 1993 with an average solar modulation level about 497 MV, roughly the same as at Earth near sunspot minimum. We obtain approximately 430 Al events of which approximately 35 are Al-26 and 395 are Al-27. The Al isotopes were separated with an average mass resolution sigma of 0.35 amu. Our interpretation of the isotopic composition of cosmic-ray aluminum is based on a standard Leaky-Box model for the interstellar propagation of cosmic-ray nuclei using the latest cross sections of the New Mexico-Saclay collaboration as well as a disk-halo diffusion model. From our observed ratio Al-26/Al-27 of 8.3 +/- 2.4 % we deduce an average interstellar density of about 0.52 (+0.26, -0.2) atoms per cu cm. This density is larger than the value of 0.28 (+0.14, -0.11) atoms per cu cm we found from an analysis of the observed abundance of the longer lived Be-10 made using data from the Voyager detectors over almost the same time interval and using essentially the same propagation program.

Lukasiak, A.↗

DOE OSTI2026

Electron–Ion Covariance Reveals Geometry-Resolved Inner-Shell Spectra in CS 2 Photodissociation

The chemical shifts of inner-shell atomic orbitals are highly sensitive to chemical bonding and molecular structure. In evolving systems, however, the spectra of distinct molecular species and geometries overlap, obscuring the underlying chemical dynamics. Here we demonstrate the use of electron–ion covariance analysis to combine the structural sensitivity of Coulomb explosion imaging with inner-shell spectroscopy, yielding geometry-specific spectra of transient and product species. We apply this approach to the excited state dynamics of CS 2 probed by ionization above the S 2p edge. Electron–ion covariance with time- and momentum-selected S + and S 2+ ions isolates distinct S 2p photoelectron spectra for ground-state CS 2 , bent photoexcited CS 2 , the CS photoproduct, and bare atomic sulfur ─ species whose spectra overlap strongly in the channel-averaged measurement. Clear chemical shifts are observed in the covariance photoelectron spectrum for each of these species, all of which are consistent with high-level calculations. Here, by extracting the atomic S contribution to the photoelectron spectrum in a finely time-resolved manner we can disentangle this contribution to the overall time-resolved photoelectron spectrum as the photodissociation proceeds. These results demonstrate the promise of electron–ion covariance as a general approach to geometry-resolved inner-shell spectroscopy, opening a route to tracking structural evolution through chemical shifts in complex photoexcited molecules.

Ionization↗

NASA NTRSDate not supplied

Implementation of active sites to capture pitting of oxidizing carbon materials in DSMC.

In this work we demonstrate a newly developed capability to capture pitting of carbon fibers in DSMC simulations, specifically using the Stochastic PArallel Rarefied-gas Time-accurate Analyzer (SPARTA) code [1]. State-of-the-art reactive surface models in DSMC compute collision dependent carbon consumption rates (usually through desorption of CO) based on a set of surface reactions that has been derived from molecular beam experiments [2]. The reactivity on each carbon surface element is constant in those models, such that the carbon surface recedes uniformly as a result of ablation. However, it is well known that in reality the carbon surface has locally different reaction rates due to the presence of defects at the atomic scale [3]. These defective sites have a much higher reactivity than the average sites (2-3 orders of magnitude) and are first to react during ablation leading to its removal. This causes all the neighboring atoms to be defective and increase their reactivity, thus leading to the localized carbon removal around these ”active” sites (as shown in Fig. 1). In this manner, these highly reactive defective sites serve as nucleation sites for the formation and growth of etch pits with potentially detrimental effects on the structural integrity. Recently a detailed surface chemistry framework was developed in SPARTA, capable of incorporating various reaction mechanisms such as adsorption, desorption, Eley-Rideal (ER) and Langmuir-Hinshelwood (LH) mechanisms [4]. Within this framework, we have implemented the capability of a single surface having multiple site sets with different reactivities. Using this feature, we can simulate the presence of active sites on carbon surfaces, whose reactivity is much greater than an average site as a result of defects. We have implemented the active site fraction as a property of surface elements within SPARTA, which is directly proportional to the local reactivity of each surface element. By introducing an initial distribution of the active site fraction across the carbon surface, and propagating it in a manner that mimics the evolution of real reacting carbon surfaces, we are able to capture the formation and growth of etch pits as a result of surface consumption reactions such as oxidation.

DSMC↗

DOE OSTI2020

The relation between lignin sequence and its 3D structure

Background: Lignin, the second most abundant biopolymer on earth, plays a major structural role in plants, conferring mechanical strength and regulating water conduction. Understanding the three-dimensional structure of lignin is important for fundamental reasons as well as engineering plants towards lignin valorization. Lignin lacks a specific primary sequence, making its average chemical composition the focus of most recent studies. However, it remains unclear whether the 3D structure of lignin molecules depends on their sequence. Methods: In this work, we performed all-atom molecular dynamics simulation of three S/G-lignin molecules with the same average composition but different sequence. Results: A detailed statistical analysis of the radius of gyration and relative shape anisotropy reveals that the lignin sequence has no statistically significant effect on the global three-dimensional structure. We found however, that homopolymers of C-lignin with the same molecular weight have smaller radii of gyration than S/G-lignin. We attribute this to lower hydroxyl content of C-lignin, which makes it more compact and rigid. Conclusions: The 3D structure of lignin is influenced by the overall content of monomeric units and interunit linkages and not by its precise primary sequence. General Significance: Lignin is assumed to not have a well-defined primary structure. The results presented here demonstrate there are no significant differences in the global 3D structure of lignin molecules with the same average composition but different primary sequence.

59 BASIC BIOLOGICAL SCIENCES↗

NASA NTRSDate not supplied

Computational Study of Oxidative Etch Pitting in FiberForm and the Effect on Its Material Properties

Erosion of carbon due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface, and have much higher reactivity compared to average non-defective sites. Thus, these active sites are first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective and increase their reactivity, thus leading to the localized carbon removal around these “active” sites. In this manner, these highly reactive defective sites serve as nucleation sites for the formation and growth of etch pits with potentially detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, a commonly used base material within many thermal protection system materials (TPS). The microstructure of virgin FiberForm obtained directly from X-ray microtomography experiments is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported within the Porous Microstructure Analysis (PuMA) software and various material properties such as elasticity, thermal conductivity, and permeability are computed. The variation of these properties as a result of the complex evolution of the surface topology due to etch pit formation is studied and analyzed. Furthermore, the effect of pitting is compared to the case of shrinking fibers, which has been the standard for modelling ablation of carbon structures; and significant differences are observed. Thus, such a physically realistic modeling of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to etch pit growth. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

Carbon Ablators↗

NASA NTRSDate not supplied

Computational Study of Oxidative Etch Pitting in FiberForm and the Effect on Its Material Properties

Erosion of carbon due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface, and have much higher reactivity compared to average non-defective sites. Thus, these active sites are first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective and increase their reactivity, thus leading to the localized carbon removal around these “active” sites. In this manner, these highly reactive defective sites serve as nucleation sites for the formation and growth of etch pits with potentially detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, a commonly used base material within many thermal protection system materials (TPS). The microstructure of virgin FiberForm obtained directly from X-ray microtomography experiments is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported within the Porous Microstructure Analysis (PuMA) software and various material properties such as elasticity, thermal conductivity, and permeability are computed. The variation of these properties as a result of the complex evolution of the surface topology due to etch pit formation is studied and analyzed. Furthermore, the effect of pitting is compared to the case of shrinking fibers, which has been the standard for modelling ablation of carbon structures; and significant differences are observed. Thus, such a physically realistic modeling of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to etch pit growth. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

Carbon Ablators↗

NASA NTRS1975

OGO-6 observations of 5577 A

A brief review is given of the data obtained by the horizon-scanning 5577-A airglow photometer flown aboard OGO 6. Data are presented which show the contributions to the 5577-A emission from the F-1 region and the Chapman airglow layer. Emission rates are calculated for both regions on the basis of the dissociative-recombination and Chapman reactions, and the atomic oxygen density and downward flux are inferred from the emission rates and several assumptions concerning the temperature dependence of the rate constants. Latitude variations in the emission rates are discussed along with variations in the altitude of the 5577-A airglow. It is shown that there is a large semiannual variation in the average effective transport properties of the lower thermosphere, that the atomic oxygen profiles near 110 km suggest a maximum in eddy diffusion at about that altitude, and that systematic variations in the altitude of the atomic oxygen maximum probably do not exceed 2 km.

Donahue, T. M.↗

DOE OSTI2021

Atomic-Scale Investigation of Oxidation at the Black Phosphorus Surface

Black phosphorus (BP) exhibits extraordinary electronic properties that are desirable for a wide variety of electronic and optoelectronic applications. However, applications of BP are hindered by its rapid degradation in ambient conditions. Despite significant advances that have been made in understanding the degradation mechanism, no consensus has yet been reached on how BP oxidation occurs at the atomic scale as experimental studies have been mostly restricted to averaged effects of degradation over a micron- to millimeter-sized region. Here, BP oxidation is investigated using scanning tunneling microscopy/spectroscopy (STM/S). Introducing O 2 gas to the BP surface in ultrahigh vacuum at a pressure of 10 –5 mbar for 1 min creates two new types of defects on the surface. We identify these defects as dangling atomic oxygen and phosphorus multivacancies using density functional theory simulations. In addition to the structural changes to the surface, the electronic structure is also drastically altered by the introduction of oxygen. The 300 meV band gap of BP is lifted due to dosing. This change in the electronic structure is reversible through STM tip manipulation. As a result, these are the first experimental results showing the atomic-scale oxidation of BP, an important step toward understanding the degradation process

2D materials↗

NASA NTRSDate not supplied

Simulation of Oxidative Etch Pit Formation and Growth on FiberForm

Erosion of carbon surfaces due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface and have much higher reactivity compared to average non-defective sites. Thus, these active sites are the first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective, and increasing their reactivity, thus leading to localized carbon removal around these “active” sites. In this manner, these highly reactive defects serve as nucleation sites for the formation and growth of etch pits, with detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in the presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, the precursor substrate of the PICA Thermal Protection System (TPS) material. The microstructure of virgin FiberForm obtained directly from X-ray microtomography scans is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported into the Porous Microstructure Analysis (PuMA) software and various material properties such as thermal conductivity, elasticity, and permeability are computed. The variation of these properties because of the complex evolution of the surface topology due to the formation of etch pits is studied and analyzed. Furthermore, the effect of pitting is compared to the case of uniform radial shrinking of fibers, which has been the standard for modelling ablation of carbon structures, and significant differences are observed. Thus, a physically realistic model of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to the growth of etch pits. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

DSMC↗

NASA NTRSDate not supplied

Simulation of Oxidative Etch Pit Formation and Growth on FiberForm

Erosion of carbon surfaces due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface and have much higher reactivity compared to average non-defective sites. Thus, these active sites are the first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective, and increasing their reactivity, thus leading to localized carbon removal around these “active” sites. In this manner, these highly reactive defects serve as nucleation sites for the formation and growth of etch pits, with detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in the presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, the precursor substrate of the PICA Thermal Protection System (TPS) material. The microstructure of virgin FiberForm obtained directly from X-ray microtomography scans is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported into the Porous Microstructure Analysis (PuMA) software and various material properties such as thermal conductivity, elasticity, and permeability are computed. The variation of these properties because of the complex evolution of the surface topology due to the formation of etch pits is studied and analyzed. Furthermore, the effect of pitting is compared to the case of uniform radial shrinking of fibers, which has been the standard for modelling ablation of carbon structures, and significant differences are observed. Thus, a physically realistic model of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to the growth of etch pits. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

DSMC↗

DOE OSTI2022

Synthesis of platinum nanoparticles on strontium titanate nanocuboids via surface organometallic grafting for the catalytic hydrogenolysis of plastic waste

Pt/SrTiO 3 (Pt/STO), prepared on small scale by atomic layer deposition (ALD), is a capable heterogeneous catalyst for the selective hydrogenolysis of polyolefins to hydrocarbon oils, providing a promising approach for upcycling plastic waste. However, because deposition by ALD is costly and resource-intensive, a new synthesis of Pt/STO is needed to effectively scale catalyst production and pursue the commercialization of upcycling processes. To that effect, this work details a scalable deposition method for Pt/STO made by surface organometallic chemistry (SOMC) techniques using Pt(II) acetylacetonate or and trimethyl(methylcyclopentadienyl)platinum. The STO support was calcined (550 °C), treated with ozone (200 °C), and finally steamed (200 °C) to afford a clean STO surface populated with only hydroxyl groups. Pt precursors were dissolved in toluene and deposited onto STO. After reduction at 300 °C, the STO support was decorated with 1.0–1.5 nm Pt nanoparticles. The size and loading of these nanoparticles were varied by employing a multi-cycle deposition and oxidation and/or reduction process designed to ALD techniques. In conclusion, these Pt/STO catalysts hydrogenolyzed isotactic polypropylene into liquid products (>95% yield) with average molecular weights of 200–300 Da (~25 carbon atoms) and narrow size distributions at 300 °C and 180 psi H 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1988

Full configuration-interaction study of the ionic-neutral curve crossing in LiF

Full configuration-interaction (FCI) calculations are used to assess the relative ability of methods for truncating the n-particle expansion in describing the ionic-neutral curve crossing between the two lowest Sigma(+) states of LiF. While the FCI calculations yield a smooth dipole moment function, MRCI calculations based on CASSCF orbitals optimized for the lowest state at all r values yield a discontinuous dipole moment function. However, when the orbitals are optimized using a state-averaged CASSCF procedure, with equal weights for the ionic and neutral solutions, both the CASSCF and MRCI dipole moment functions are smooth and in reasonable agreement with the FCI. No single-reference-based method is found to work satisfactorily. Potential curves for the lowest two Sigma(+) states are determined in both the adiabatic and diabatic representations using a large atomic natural orbit Gaussian basis set and a state-averaged CASSCF/MRCI treatment of electron correlation.

Bauschlicher, Charles W., Jr.↗

NASA NTRS1974

The global characteristics of atmosphere emissions in the lower thermosphere and their aeronomic implications

The green line of atomic oxygen and the Herzberg bands of molecular oxygen as observed from the OGO-4 airglow photometer are discussed in terms of their spatial and temporal distributions and their relation to the atomic oxygen content in the lower thermosphere. Daily maps of the distribution of emissions show considerable structure (cells, patches, and bands) with appreciable daily changes. When data are averaged over periods of several days in length, the resulting patterns have occasional tendencies to follow geomagnetic parallels. The Seasonal variations are characterized by maxima in both the Northern and Southern Hemispheres in October, with the Northern Hemisphere having substantially higher emission rates. Formulae are derived relating the vertical column emission rates of the green line and the Herzberg bands to the atomic oxygen peak density. Global averages for the time period for these data (August 1967 to January 1968), when converted to maximum atomic oxygen densities near 95 km, have a range of 2.0 x 10 to the 11th power/cu cm 2.7 x 10 to the 11th power/cu cm.

Reed, E. I.↗

NASA NTRS2018

GMI-IPS: Python Processing Software for Aircraft Campaigns

NASA's Atmospheric Tomography Mission (ATom) seeks to understand the impact of anthropogenic air pollution on gases in the Earth's atmosphere. Four flight campaigns are being deployed on a seasonal basis to establish a continuous global-scale data set intended to improve the representation of chemically reactive gases in global atmospheric chemistry models. The Global Modeling Initiative (GMI), is creating chemical transport simulations on a global scale for each of the ATom flight campaigns. To meet the computational demands required to translate the GMI simulation data to grids associated with the flights from the ATom campaigns, the GMI ICARTT Processing Software (GMI-IPS) has been developed and is providing key functionality for data processing and analysis in this ongoing effort. The GMI-IPS is written in Python and provides computational kernels for data interpolation and visualization tasks on GMI simulation data. A key feature of the GMI-IPS, is its ability to read ICARTT files, a text-based file format for airborne instrument data, and extract the required flight information that defines regional and temporal grid parameters associated with an ATom flight. Perhaps most importantly, the GMI-IPS creates ICARTT files containing GMI simulated data, which are used in collaboration with ATom instrument teams and other modeling groups. The initial main task of the GMI-IPS is to interpolate GMI model data to the finer temporal resolution (1-10 seconds) of a given flight. The model data includes basic fields such as temperature and pressure, but the main focus of this effort is to provide species concentrations of chemical gases for ATom flights. The software, which uses parallel computation techniques for data intensive tasks, linearly interpolates each of the model fields to the time resolution of the flight. The temporally interpolated data is then saved to disk, and is used to create additional derived quantities. In order to translate the GMI model data to the spatial grid of the flight path as defined by the pressure, latitude, and longitude points at each flight time record, a weighted average is then calculated from the nearest neighbors in two dimensions (latitude, longitude). Using SciPya's Regular Grid Interpolator, interpolation functions are generated for the GMI model grid and the calculated weighted averages. The flight path points are then extracted from the ATom ICARTT instrument file, and are sent to the multi-dimensional interpolating functions to generate GMI field quantities along the spatial path of the flight. The interpolated field quantities are then written to a ICARTT data file, which is stored for further manipulation. The GMI-IPS is aware of a generic ATom ICARTT header format, containing basic information for all flight campaigns. The GMI-IPS includes logic to edit metadata for the derived field quantities, as well as modify the generic header data such as processing dates and associated instrument files. The ICARTT interpolated data is then appended to the modified header data, and the ICARTT processing is complete for the given flight and ready for collaboration. The output ICARTT data adheres to the ICARTT file format standards V1.1. The visualization component of the GMI-IPS uses Matplotlib extensively and has several functions ranging in complexity. First, it creates a model background curtain for the flight (time versus model eta levels) with the interpolated flight data superimposed on the curtain. Secondly, it creates a time-series plot of the interpolated flight data. Lastly, the visualization component creates averaged 2D model slices (longitude versus latitude) with overlaid flight track circles at key pressure levels. The GMI-IPS consists of a handful of classes and supporting functionality that have been generalized to be compatible with any ICARTT file that adheres to the base class definition. The base class represents a generic ICARTT entry, only defining a single time entry and 3D spatial positioning parameters. Other classes inherit from this base class; several classes for input ICARTT instrument files, which contain the necessary flight positioning information as a basis for data processing, as well as other classes for output ICARTT files, which contain the interpolated model data. Utility classes provide functionality for routine procedures such as: comparing field names among ICARTT files, reading ICARTT entries from a data file and storing them in data structures, and returning a reduced spatial grid based on a collection of ICARTT entries. Although the GMI-IPS is compatible with GMI model data, it can be adapted with reasonable effort for any simulation that creates Hierarchical Data Format (HDF) files. The same can be said of its adaptability to ICARTT files outside of the context of the ATom mission. The GMI-IPS contains just under 30,000 lines of code, eight classes, and a dozen drivers and utility programs. It is maintained with GIT source code management and has been used to deliver processed GMI model data for the ATom campaigns that have taken place to date.

Damon, M. R.↗

DOE OSTI2023

Dynamic crystallography reveals spontaneous anisotropy in cubic GeTe

Cubic energy materials such as thermoelectrics or hybrid perovskite materials are often understood to be highly disordered. In GeTe and related IV–VI compounds, this is thought to provide the low thermal conductivities needed for thermoelectric applications. Since conventional crystallography cannot distinguish between static disorder and atomic motions, we develop the energy-resolved variable-shutter pair distribution function technique. This collects structural snapshots with varying exposure times, on timescales relevant for atomic motions. In disagreement with previous interpretations, we find the time-averaged structure of GeTe to be crystalline at all temperatures, but with anisotropic anharmonic dynamics at higher temperatures that resemble static disorder at fast shutter speeds, with correlated ferroelectric fluctuations along the <100> c direction. We show that this anisotropy naturally emerges from a Ginzburg–Landau model that couples polarization fluctuations through long-range elastic interactions. By accessing time-dependent atomic correlations in energy materials, we resolve the long-standing disagreement between local and average structure probes and show that spontaneous anisotropy is ubiquitous in cubic IV–VI materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2020

Using a carbon vacancy reduction material to increase average carrier lifetime in a silicon carbide semiconductor device

A semiconductor die and a process for fabricating the semiconductor die are disclosed. The semiconductor die has a substrate and a silicon carbide (SiC) epitaxial structure on the substrate. The SiC epitaxial structure includes at least a first N-type SiC layer, at least a first P-type SiC layer, and carbon vacancy reduction material, which has been implanted into a surface of the SiC epitaxial structure. Further, the SiC epitaxial structure has been annealed to mobilize the carbon vacancy reduction material to diffuse carbon atoms substantially throughout the SiC epitaxial structure, thereby increasing an average carrier lifetime in the SiC epitaxial structure.

36 MATERIALS SCIENCE↗

DOE OSTI2021

A highly efficient atomically thin curved PdIr bimetallene electrocatalyst

Abstract The multi-metallene with an ultrahigh surface area has great potential in precise tuning of surface heterogeneous d-electronic correlation by surface strain effect for the distinctive surface electronic structure, which is a brand new class of promising 2D electrocatalyst for sustainable energy device application. However, achieving such an atomically thin multi-metallene still presents a great challenge. Herein, we present a new synthetic method for an atomic-level palladium-iridium (PdIr) bimetallene with an average thickness of only ∼1.0 nm for achieving superior catalysis in the hydrogen evolution reaction (HER) and the formic acid oxidation reaction (FAOR). The curved PdIr bimetallene presents a top-ranked high electrochemical active area of 127.5 ± 10.8 m2 gPd+Ir−1 in the reported noble alloy materials, and exhibits a very low overpotential, ultrahigh activity and improved stability for HER and FAOR. DFT calculation reveals that the PdIr bimetallene herein has a unique lattice tangential strain, which can induce surface distortion while concurrently creating a variety of concave-convex featured micro-active regions formed by variously coordinated Pd sites agglomeration. Such a strong strain effect correlates the abnormal on-site active 4d10-t2g-orbital Coulomb correlation potential and directly elevates orbital-electronegativity exposure within these active regions, resulting in a preeminent barrier-free energetic path for significant enhancement of FAOR and HER catalytic performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗