Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ambient temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Diamond and methane formation from the chemical decomposition of polyethylene at high pressures and temperatures

Abstract Polyethylene (C 2 H 4 ) n was compressed to pressures between 10 and 30 GPa in a diamond anvil cell (DAC) and laser heated above 2500 K for approximately one second. This resulted in the chemical decomposition of the polymer into carbon and hydrocarbon reaction products. After quenching to ambient temperature, the decomposition products were measured in the DAC at pressures ranging from ambient to 29 GPa using a combination of x-ray diffraction (XRD) and small angle x-ray scattering (SAXS). XRD identified cubic diamond and methane as the predominant product species with their pressure–volume relationships exhibiting strong correlations to the diamond and methane equations of state. Length scales associated with the diamond products, obtained from SAXS measurements, indicate the formation of nanodiamonds with a radius of gyration between 12 and 35 nm consistent with 32–90 nm diameter spherical particles. These results are in good agreement with the predicted product composition under thermodynamic and chemical equilibrium.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Modeling Contact Angle vs. Temperature for the Quartz-Water-Decane System

Innovative approaches are needed to improve the efficiency of oil recovery technologies to meet the growing demands of fossil-fuel based energy consumption. Enhanced oil recovery (EOR) methods such as low-salinity waterflooding and chemically tuned waterflooding aim to optimize the reservoir’s wetting properties, detaching oil globules from rock surfaces and allowing easier oil flow through pore throats. This wetting behavior is commonly quantified by contact angle measurements of the rock-oil-brine interface, which have been thoroughly investigated and theorized for many systems at ambient temperatures and pressures. However, few studies exist for extending contact angle theories away from ambient conditions. In this paper, we model the contact angles of a quartz-water-decane system at elevated temperatures using the surface tension component (STC) approach. Temperature-dependent van der Waals [Lifshitz-van der Waals (LW)] interactions and hydrogen-bonding (acid-base) interactions were calculated and are incorporated into the model for the quartz-water-decane interface. Additionally, the Hough and White procedure was used to create temperature-dependent dielectric functions of quartz, water, and normal decane for calculations of Hamaker coefficients. Hamaker coefficients calculated this way are highly linear with temperature and agree well with Israelachvili’s approximation. The acid-base interactions likely contribute the most to system wettability changes. Resulting contact angles of the quartz-water-decane system shift from water-wet (16°) to slightly water-wet (57.4°) as temperature increases. The model was also successfully verified for the quartz-air-water system. Our results can be used in future studies to determine optimal injected water compositions for specific rock-oil-brine and other systems with consideration of reservoir temperature.

02 PETROLEUM↗
DOE OSTI2021

Multiphase, Multiscale Chemomechanics at Extreme Low Temperatures: Battery Electrodes for Operation in a Wide Temperature Range

Understanding the behavior of lithium-ion batteries (LIBs) under extreme conditions, for example, low temperature, is key to broad adoption of LIBs in various application scenarios. LIBs, poor performance at low temperatures is often attributed to the inferior lithium-ion transport in the electrolyte, which has motivated new electrolyte development as well as the battery preheating approach that is popular in electric vehicles. A significant irrevocable capacity loss, however, is not resolved by these measures nor well understood. Herein, multiphase, multiscale chemomechanical behaviors in composite LiNi x Mn y Co z O 2 (NMC, x + y + z = 1) cathodes at extremely low temperatures are systematically elucidated. The low-temperature storage of LIBs can result in irreversible structural damage in active electrodes, which can negatively impact the subsequent battery cycling performance at ambient temperature. Furthermore, beside developing electrolytes that have stable performance, designing batteries for use in a wide temperature range also calls for the development of electrode components that are structurally and morphologically robust when the cell is switched between different temperatures.

25 ENERGY STORAGE↗
DOE OSTI2022

Multi-mechanistic Strategies for Novel Solid Electrolytes with Superior Properties

Despite a wide range of solid electrolyte phases, most of them only exist at high temperatures. The challenge is to tailor the chemical compositions of solid electrolyte materials that yield high ionic conductivities and low activation energies at ambient temperature. This is crucial for the development of all-solid-state batteries that are both powerful and safe. Here, we report our recent works to meet this challenge by utilizing multiple mechanistic principles and clusters as the building blocks. We show that the atomic-level interactions that govern the fast-ion conduction can be optimized by incorporating polyanion dynamics, non-stoichiometry, point defects and strong ionic correlations. Specifically, two case studies of Li/Na solid electrolytes will be covered, including lithium solid electrolytes (SE) with record-high ionic conductivities at room temperature (over 100 mS/cm) and sodium SE with record-low activation energies (< 0.1 eV).

Fang, Hong↗
DOE OSTI2023

A Sustainable Multi-Dimensional Printable Material

Polymeric materials are usually tailored for specific functionality. A single polymer exhibiting multiple simultaneous functionalities often requires intricate molecular architecture, which is difficult to manufacture at scale because of its complex synthesis routes. In this work, a facile, partly renewable composition—prepared via reactive melt processing—that induces tunable functionalities such as 3D printability, shape recovery, and self-healing while exhibiting satisfactory mechanical properties is reported. The system with a hydrogen-bonded 3D network consists of thermally reversible nano-scale agglomerates of sustainable, rigid phenolic oligomers and crystallizable flexible polymer. Local molecular mobility and temperature-dependent relaxation and recovery of the non-equilibrium networked states enable exploiting these simultaneous functionalities. Transitions involving solidification and structure stabilization at ambient temperature spanning several hours after preheating only at 70 °C directly contrast typical thermoplastic or thermoplastic elastomer behaviors. Results from this study can inform the design of future rheology modifiers and materials for soft robotics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Design and performance validation of a high-temperature downhole permanent magnet generator used for an electro-pulse boring system in geothermal energy applications

Novel, direct-energy drilling technologies such as electro-pulse boring, have the potential to significantly increase the speed and depth of geothermal drilling but have not achieved widespread adoption due to several economic and technical barriers. One major challenge is that these drilling systems require electric power downhole. The current practice is to supply power to the drill string components by running electric cables down the geothermal well, but at the targeted well depths, this practice is cost-inhibitive, inefficient in terms of power consumption, and adds an additional failure point with the long cabling going through a highly corrosive, high-temperature environment. A solution to this problem is to develop high-temperature electric generator technology that can generate the required power downhole. Such a generator must also operate with high efficiency at the target downhole ambient temperature of 250 °C. In this paper, we investigate the various design considerations for this concept and subsequently design the downhole electric generator using a multi-objective design optimization approach. Through electromagnetic-, thermal- and short-circuit fault condition analysis, it is demonstrated that the optimized downhole electric generator concept presented in this paper can meet the performance requirements within this extreme drilling environment. Most remarkably, it is shown that a generator efficiency of 90% is achieved. In conclusion, to validate the results presented in this paper, a prototype generator is built and its performance is measured at 250 °C using a test bench uniquely developed for this application.

15 GEOTHERMAL ENERGY↗
DOE OSTI2024

Necromass responses to warming: A faster microbial turnover in favor of soil carbon stabilisation

Microbial byproducts and residues (hereafter ‘necromass’) potentially play the most critical role in soil organic carbon (SOC) sequestration. However, little is known about the influence of climate warming on necromass accumulation in the agroecosystem and the underlying mechanisms associated with microbial life strategies. Here, in order to address these knowledge gaps, we used amino sugars as biomarkers of microbial necromass, and investigated their variation through an 8-year trial in an agroecosystem with two warming levels (+1.6 and + 3.2 °C) compared to ambient temperature. The results showed that the lower warming level had no impact on total microbial necromass carbon. Conversely, warming the soil 3.2 °C above ambient increased total microbial necromass by 17 % and its contribution to SOC by 21.3 %, mainly by increasing fungal necromass (+19.8 %), whereas +3.2 °C warming had no impact on bacterial necromass. At the phylum level, compared with the ambient control, +3.2 °C warming induced an increase in the abundance of Proteobacteria and a decrease in both Acidobacteria and Actinobacteria, whereas in the fungal community, Ascomycota increased and Mortierellomycota decreased. This indicates that r-strategists outcompete K-strategists in warmer climates, which led to increased microbial necromass production and accumulation, as supported by the positive correlation between r-strategists and microbial necromass. Stronger microbial competition for resources also resulted in a higher biomass turnover rate, greater cell death, and greater production of microbial necromass. This was supported by the lower bacterial and fungal network complexity and trophic links under warming conditions. In addition, the necromass generated from accelerated microbial turnover further offsets warming-induced deceases in microbial biomass. Consequently, bulk SOC did not change, despite microbial necromass having a much greater response to warming than the soil C pool. Therefore, future climate warming may influence the composition and persistence of SOC during microbial degradation.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Assessment of Blocking Contacts in Suppressing Polarization Effects in CsPbBr 3 Perovskite Detectors

The CsPbBr 3 perovskite has garnered significant attention as a room-temperature semiconductor for hard radiation detection due to straightforward synthesis, scalable crystal growth, low cost, and excellent energy resolution. However, despite these advantages, at ambient temperature, CsPbBr 3 devices may experience performance deterioration and irreversible failure due to “polarization” induced by electromigration of ions to electrical connections on the device. In this study, we tested several contact materials and their optimization deposition techniques to assess the stability of high-performance CsPbBr 3 γ-ray detectors. Metals, with low work functions (Ti, In, Sn, Sb, Pb, Bi, Al, Au, and TiC) and high-work-function (Au or Pt) contacts, were used to form different Schottky junctions using vacuum thermal evaporation, electron-beam evaporation, and sputtering methods. These detectors were tested in intermittent and continuous modes to assess their stability. Among the tested detectors, the Bi/CLB/Pt electrode configuration demonstrated superior stability, operating effectively for 11 months under periodic testing and 16 days under continuous testing. In contrast, other configurations functioned only for a few months under intermittent conditions. Upon incorporating a ~40-nm-thick TiC passivation layer on the anode side (Bi/TiC/CLB/Pt), the CLB device operated continuously for 36 days without degradation. In many cases, the failure mode of the devices was due to the degradation of the anode. Here, the chemical changes in the fresh and deteriorated anodes were characterized using scanning electron microscopy and energydispersive X-ray spectroscopy

CsPbBr3 perovskite↗
DOE OSTI2020

In situ characterization of residual stress evolution during heat treatment of SiC/SiC ceramic matrix composites using high-energy X-ray diffraction

Volumetric strains were measured in silicon carbide/silicon carbide melt-infiltrated ceramic matrix composites (CMCs) at ambient and high temperatures using high-energy synchrotron X-ray diffraction (XRD). Both silicon and silicon carbide constituents were interrogated utilizing a broad spectrum of diffracting planes that would be largely inaccessible to common laboratory XRD equipment. Residual room-temperature principal strains in the melt-infiltrated silicon phase were found to be approximately 1100 mu epsilon in compression, corresponding to stresses of approximately 300 MPa using simplifying constitutive assumptions. Residual room-temperature principal strains in silicon carbide particles found throughout the matrix were approximately 500 mu epsilon in tension, corresponding to approximately 300 MPa. Residual strains were found to decrease considerably as temperatures increased from ambient temperature to 1250 degrees C. Additionally, residual strains returned to approximately preheat treatment values after cool-down to ambient temperature. Strain measurements in the silicon phase were found to be significantly affected by dissolved boron dopant levels causing contraction of the silicon lattice. This contraction must be accounted for in high-temperature experiments for accurate calculation of stresses in the silicon phase.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Investigation of a high-temperature combination heat pump for lower-cost electrification in multifamily buildings

The development of space and water heating combination heat pumps capable of generating water temperatures high enough for convective heat emitters will enable more cost-effective and equitable decarbonization solutions for electrifying multifamily buildings. Here, in this paper, multifamily building models and a charge-sensitive mechanistic cycle model of a combination heat pump are developed, and the system performance is predicted based on the models. Unlike other state-of-the-art residential heat pumping equipment, the modeled combination heat pump using an economized, fluid-injected variable-speed compressor can achieve higher temperature lifts of 40° - 85°C, with lower installation costs and complexity. The model predicted heating coefficient of performance (COP h ) is 2.1 at an ambient temperature of -15°C with a high-temperature lift of nearly 85°C, and a seasonal coefficient of performance in heating mode (SCOP h ) ranges from 2 - 4 for different locations. The system shows 30% - 90% lower CO 2 eq emissions over a condensing gas boiler and 9% - 13% lower projected installation costs than two separate space and water heat pumping appliances.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

Computational Optimization of Room Temperature Usable Capacity for Hydrogen Storage in MFU-4-Type Metal–Organic Frameworks via Pairwise Metal Substitutions

The efficient storage of hydrogen is a critical challenge in the quest for sustainable energy solutions. Current adsorbent-based methods achieve satisfactory storage densities predominantly under cryogenic temperatures and/or high pressures, which imposes problems with cost-efficient and safe implementation of this technology. Materials that can bind hydrogen gas reversibly at ambient temperatures and more moderate pressures could play a pivotal role in enabling hydrogen-powered technologies. In this study, we use reliable computational modeling to investigate two synthetically feasible paths for tuning the enthalpy of H2 binding in MFU-4-type metal–organic frameworks (MOFs), aiming to maximize usable capacity. This study examines MIM4 IICl3(bta)6 (bta– = benzotriazolate) Kuratowski-type clusters as a model for strong binding sites in MFU-4l frameworks. We systematically evaluate the impact of separately tuning the central MII metal ion (which plays a structural role) and the peripheral MI metal ion (which binds the substrate) on the energetics of H2 binding. Our computational study reveals that H2 binding at an MI site mostly follows the trend AgI < CuI < NiI < CoI < AuI while a larger central MII site generally weakens the H2 binding at a MI site. Importantly, we have identified three new combinations of MI and MII to achieve high fractional usable capacities of the total H2 adsorbed under a pressure swing from 5 to 100 bar at room temperature. Additionally, we examine the nature of the binding interaction between the peripheral metal atom and the hydrogen molecule. While charge transfer predominantly induces this interaction, for several atom combinations, a change in the polarization (associated with variations in the ionic radius of the MI binding atom) is another important factor for adjusting the strength of the interaction. We suggest that the proposed compositions of Kuratowski-type clusters are highly desirable synthetic targets for future laboratory study.

Tkachenko, Nikolay V↗
DOE OSTI2020

Ammonia-salt solvent promotes cellulosic biomass deconstruction under ambient pretreatment conditions to enable rapid soluble sugar production at ultra-low enzyme loadings

In this paper, we report a novel ammonia : ammonium salt solvent based pretreatment process that can rapidly dissolve crystalline cellulose into solution and eventually produce highly amorphous cellulose under near-ambient conditions. Pre-activating the cellulose I allomorph to its ammonia–cellulose swollen complex (or cellulose III allomorph) at ambient temperatures facilitated rapid dissolution of the pre-activated cellulose in the ammonia-salt solvent ( i.e. , ammonium thiocyanate salt dissolved in liquid ammonia) at ambient pressures. For the first time in reported literature, we used time-resolved in situ neutron scattering methods to characterize the cellulose polymorphs structural modification and understand the mechanism of crystalline cellulose dissolution into a ‘molecular’ solution in real-time using ammonia-salt solvents. We also used molecular dynamics simulations to provide insight into solvent interactions that non-covalently disrupted the cellulose hydrogen-bonding network and understand how such solvents are able to rapidly and fully dissolve pre-activated cellulose III. Importantly, the regenerated amorphous cellulose recovered after pretreatment was shown to require nearly ~50-fold lesser cellulolytic enzyme usage compared to native crystalline cellulose I allomorph for achieving near-complete hydrolytic conversion into soluble sugars. Lastly, we provide proof-of-concept results to further showcase how such ammonia-salt solvents can pretreat and fractionate lignocellulosic biomass like corn stover under ambient processing conditions, while selectively co-extracting ~80–85% of total lignin, to produce a highly digestible polysaccharide-enriched feedstock for biorefinery applications. Unlike conventional ammonia-based pretreatment processes ( e.g. , Ammonia Fiber Expansion or Extractive Ammonia pretreatments), the proposed ammonia-salt process can operate at near-ambient conditions to greatly reduce the pressure/temperature severity necessary for conducting effective ammonia-based pretreatments on lignocellulose.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Aircraft-Integrated Meteorological Measurement System (AIMMS) Instrument Handbook

The AIMMS-20 probe is manufactured by Aventech Research Inc. and measures platform position, velocity, attitude, ambient temperature, static pressure, and the differential pressures from a 5-port hemispheric gust probe, and combines all these measured data into a calculation of the ambient winds. A detailed description of the AIMMS-20 specifications is available here. Note: The Aventech engineers use the aircraft-centric frame of reference common to aeronautical engineering, which defines z as down.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Effect of hydrogen on tensile properties of 304L stainless steel at cryogenic temperatures

Safe and efficient hydrogen storage and distribution are key attributes to realizing hydrogen as an alternative energy carrier. To this end, cryogenic liquid and cryo-compressed gaseous hydrogen are considered high energy density alternatives to ambient temperature gas. However, these alternatives have significant material demands to overcome extreme temperature (20 K) and pressure (700 bar) as well as hydrogen effects. Austenitic stainless steels are widely used for cryogenic pressure vessels owing to relatively high ductility even at 4 K. However, the influence of hydrogen on mechanical properties at cryogenic temperatures has rarely been studied. In this study, the tensile properties of 304L austenitic stainless steel with internal hydrogen were evaluated at 20 K, 77 K, and 113 K. Test specimens were saturated with internal hydrogen to concentration of 140 wtppm in a high pressure environment at elevated temperature, a process called thermal precharging. While lower temperature in known to increase strength properties and reduced elongation at fracture, the presence of internal hydrogen increased both strength and elongation at fracture, but reduced ductility. Magnetic evaluation of the uniformly strained region of the test specimens suggest that hydrogen mitigates the strain-induced transformation to a’-martensite. Brittle fracture features and secondary cracking indicative of hydrogen embrittlement were observed on the fracture surfaces of hydrogen-precharged specimens, which is consistent with the loss of ductility.

Merkel, Daniel R.↗
DOE OSTI2022

Metal-free carbocatalyst for room temperature acceptorless dehydrogenation of N-heterocycles

Catalytic dehydrogenation enables reversible hydrogen storage in liquid organics as a critical technology to achieve carbon neutrality. However, oxidant or base-free catalytic dehydrogenation at mild temperatures remains a challenge. Here, we demonstrate a metal-free carbocatalyst, nitrogen-assembly carbons (NCs), for acceptorless dehydrogenation of N-heterocycles even at ambient temperature, showing greater activity than transition metal–based catalysts. Mechanistic studies indicate that the observed catalytic activity of NCs is because of the unique closely placed graphitic nitrogens (CGNs), formed by the assembly of precursors during the carbonization process. The CGN site catalyzes the activation of C–H bonds in N-heterocycles to form labile C–H bonds on catalyst surface. The subsequent facile recombination of this surface hydrogen to desorb H 2 allows the NCs to work without any H-acceptor. With reverse transfer hydrogenation of various N-heterocycles demonstrated in this work, these NC catalysts, without precious metals, exhibit great potential for completing the cycle of hydrogen storage.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Extending the low-temperature operation of sodium metal batteries combining linear and cyclic ether-based electrolyte solutions

Nonaqueous sodium-based batteries are ideal candidates for the next generation of electrochemical energy storage devices. However, despite the promising performance at ambient temperature, their low-temperature (e.g., < 0 °C) operation is detrimentally affected by the increase in the electrolyte resistance and solid electrolyte interphase (SEI) instability. Here, to circumvent these issues, we propose specific electrolyte formulations comprising linear and cyclic ether-based solvents and sodium trifluoromethanesulfonate salt that are thermally stable down to –150 °C and enable the formation of a stable SEI at low temperatures. When tested in the Na||Na coin cell configuration, the low-temperature electrolytes enable long-term cycling down to –80 °C. Via ex situ physicochemical (e.g., X-ray photoelectron spectroscopy, cryogenic transmission electron microscopy and atomic force microscopy) electrode measurements and density functional theory calculations, we investigate the mechanisms responsible for efficient low-temperature electrochemical performance. We also report the assembly and testing between –20 °C and –60 °C of full Na||Na 3 V 2 (PO 4 ) 3 coin cells. The cell tested at –40 °C shows an initial discharge capacity of 68 mAh g –1 with a capacity retention of approximately 94% after 100 cycles at 22 mA g –1 .

25 ENERGY STORAGE↗
DOE OSTI2022

Microstructure of Methylammonium Lead iodide Perovskite Thin Films: A Comprehensive Study of the Strain and Texture

Controlling the microstructure of hybrid halide perovskite thin films is essential for optimizing their performance in optoelectronic devices. It is well established that the strain state of the perovskite layer affects its stability. Likewise, the orientation of the perovskite lattice is a determining parameter as these materials have shown pronounced anisotropies in their physical and mechanical properties. In this work, the authors focus on the understanding of the mechanisms that govern the strain and texture observed in MAPbI 3 thin films deposited on various oxide substrates. A thorough study of the evolution of the strain of the perovskite layer upon cooling down to room temperature from the crystallization temperature (100 °C) shows an essentially relaxed behavior of the perovskite layers. This result contradicts the commonly accepted hypothesis according to which MAPbI 3 layers synthesized above ambient temperature are strained due to the large mismatch in the thermal expansion coefficients of the perovskite and its substrate. The texture in MAPbI 3 layers is investigated by means of synchrotron full-field diffraction X-ray microscopy. This technique allows the direct observation of the [hh0] and [00l]-oriented domains at the origin of the observed textures, demonstrating both their twin and ferroelastic nature. The stability of the different domain orientations is investigated by DFT calculations, illustrating the determining role of the chemical environment at the film-substrate interface. PbI 2- terminated surfaces are found to favor the [hh0] orientations while for MAI-terminated ones, both [hh0] and [00l] domains are equally stabilized. The different results constitute an important step of clarification and understanding from the perspective of controlling the microstructure of perovskite layers.

36 MATERIALS SCIENCE↗