Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “aerodynamic optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Multipoint Aerostructural Optimization of Wind Turbine Rotors Using a Coupled Blade‐Resolved Aerostructural Solver

Physics‐based design optimization workflows thread the needle between computational cost limitations and simulation complexity, often compromising between modeling detail and the range of operating design conditions. Multipoint aerostructural optimization of wind turbine rotors has so far been confined to low‐fidelity analyses or to high‐fidelity studies with simplified structural models, leaving the most complex design trade‐offs unexplored. We close this gap by performing the first tightly coupled gradient‐based multipoint aerostructural rotor optimization using 3D aerodynamic and structural solvers with discrete coupled adjoints. The optimizer simultaneously varies blade planform, airfoil shapes, and structural thickness through more than 270 design variables, minimizing a weighted combination of rotor mass and power across multiple wind speeds. Applied to a modified DTU 10‐MW benchmark under conservative structural and aerodynamic constraints, our multipoint optimization reduces rotor mass by up to 36% and increases power by 12%–15% across the main operating conditions; biasing the objective toward power yields power gains up to 18% and a 17% mass reduction. For a nominal wind distribution, 3‐point rotor designs accounting for low RPM and high thrust conditions capture dominant trade‐offs and outperform single‐point designs. Adding two off‐design points changes individual‐condition power by less than 3% but leaves the weighted average within 0.5%, and the mass‐power bias has a stronger effect on the final design than the operating‐point weighting itself. Our framework extends naturally to richer load cases and site‐specific wind distributions, providing a basis for high‐fidelity multipoint design earlier in industrial workflows.

17 WIND ENERGY↗
NASA NTRSDate not supplied

High-Fidelity Aeropropulsive Optimization of a Mail-Slot Distributed Electric Propulsion System for the SUSAN Electrofan

Hybrid- and all-electric aircraft concepts use electric motors for power rather than a conventional jet engine. Electric propulsors open the door to new ways to synergistically integrate the propulsion system with the airframe. For example, many small electric propulsors can be distributed along the wing to increase the effective bypass ratio for better overall efficiency. Furthermore, these propulsors can be attached to the wing surface for boundary layer ingestion(BLI) to further the efficiency gains. However, these novel methods of aeropropulsive integration also create challenges such as nonuniform inflow and complex nacelle geometries. Here we use gradient-based aerodynamic shape optimization to address the design challenges of the wing-mounted distributed electric propulsion system of the Subsonic Single Aft Engine (SUSAN)concept. In doing so, we aim to more accurately benchmark the flow power of SUSAN’s mail slot propulsors relative to a conventional propulsion system in both an isolated and BLI configuration. Our preliminary results found relative to an optimized podded propulsor the optimized mailslot and BLI mailslot design required 8% and 17% more flow power respectively.The methods and key design insights also apply to other aircraft concepts that utilize distributed electric propulsion and boundary layer ingestion.

CAS↗
DOE OSTI2020

Gradient-based constrained optimization using a database of linear reduced-order models

A methodology grounded in model reduction is presented for accelerating the gradient-based solution of a family of linear or nonlinear constrained optimization problems where the constraints include at least one linear Partial Differential Equation (PDE). A key component of this methodology is the construction, during an offline phase, of a database of pointwise, linear, Projection-based Reduced-Order Models (PROM)s associated with a design parameter space and the linear PDE(s). A parameter sampling procedure based on an appropriate saturation assumption is proposed to maximize the efficiency of such a database of PROMs. A real-time method is also presented for interpolating at any queried but unsampled parameter vector in the design parameter space the relevant sensitivities of a PROM. The practical feasibility, computational advantages, and performance of the proposed methodology are demonstrated for several realistic, nonlinear, aerodynamic shape optimization problems governed by linear aeroelastic constraints.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1975

Design and simulation of a descent controller for strategic four-dimensional aircraft navigation

A time-controlled navigation system applicable to the descent phase of flight for airline transport aircraft was developed and simulated. The design incorporates the linear discrete-time sampled-data version of the linearized continuous-time system describing the aircraft's aerodynamics. Using optimal linear quadratic control techniques, an optimal deterministic control regulator which is implementable on an airborne computer is designed. The navigation controller assists the pilot in complying with assigned times of arrival along a four-dimensional flight path in the presence of wind disturbances. The strategic air traffic control concept is also described, followed by the design of a strategic control descent path. A strategy for determining possible times of arrival at specified waypoints along the descent path and for generating the corresponding route-time profiles that are within the performance capabilities of the aircraft is presented. Using a mathematical model of the Boeing 707-320B aircraft along with a Boeing 707 cockpit simulator interfaced with an Adage AGT-30 digital computer, a real-time simulation of the complete aircraft aerodynamics was achieved. The strategic four-dimensional navigation controller for longitudinal dynamics was tested on the nonlinear aircraft model in the presence of 15, 30, and 45 knot head-winds. The results indicate that the controller preserved the desired accuracy and precision of a time-controlled aircraft navigation system.

Lax, F. M.↗
NASA NTRS1972

Low-speed aerodynamic characteristics of an airfoil optimized for maximum lift coefficient

An investigation has been conducted in the Langley low-turbulence pressure tunnel to determine the two-dimensional characteristics of an airfoil optimized for maximum lift coefficient. The design maximum lift coefficient was 2.1 at a Reynolds number of 9.7 million. The airfoil with a smooth surface and with surface roughness was tested at angles of attack from 6 deg to 26 deg, Reynolds numbers (based on airfoil chord) from 2.0 million to 12.9 million, and Mach numbers from 0.10 to 0.35. The experimental results are compared with values predicted by theory. The experimental pressure distributions observed at angles of attack up to at least 12 deg were similar to the theoretical values except for a slight increase in the experimental upper-surface pressure coefficients forward of 26 percent chord and a more severe gradient just behind the minimum-pressure-coefficient location. The maximum lift coefficients were measured with the model surface smooth and, depending on test conditions, varied from 1.5 to 1.6 whereas the design value was 2.1.

Bingham, G. J.↗
NASA NTRS1983

Supersonic-Wing Nonlinear Aerodynamics

Supersonic Wing Nonlinear Aerodynamics computer program, LTSTAR, estimates nonlinear aerodynamics characteristics of wing at supersonic speeds. Program provides generally improved predictions of wing overall force and moment coefficients. LTSTAR is useful in design studies aimed at aerodynamic performance optimization and providing more-realistic tradeoff information for selection of wing planform geometry and airfoil section parameters.

Carlson, H. W.↗
NASA NTRS1983

Loads and aeroelasticity division research and technology accomplishments for FY 1982 and plans for FY 1983

Accomplishments of the past year and plans for the coming year are highlighted as they relate to five year plans and the objectives of the following technical areas: aerothermal loads; multidisciplinary analysis and optimization; unsteady aerodynamics; and configuration aeroelasticity. Areas of interest include thermal protection system concepts, active control, nonlinear aeroelastic analysis, aircraft aeroelasticity, and rotorcraft aeroelasticity and vibrations.

Gardner, J. E.↗
NASA NTRS1990

Large-scale aeroacoustic research feasibility and conceptual design of test-section inserts for the Ames 80- by 120-foot wind tunnel

An engineering feasibility study was made of aeroacoustic inserts designed for large-scale acoustic research on aircraft models in the 80 by 120 foot Wind Tunnel at NASA Ames Research Center. The advantages and disadvantages of likely designs were analyzed. Results indicate that the required maximum airspeed leads to the design of a particular insert. Using goals of 200, 150, and 100 knots airspeed, the analysis indicated a 30 x 60 ft open-jet test section, a 40 x 80 ft open jet test section, and a 70 x 100 ft closed test section with enhanced wall lining, respectively. The open-jet inserts would be composed of a nozzle, collector, diffuser, and acoutic wedges incorporated in the existing 80 x 120 test section. The closed test section would be composed of approximately 5 ft acoustic wedges covered by a porous plate attached to the test section walls of the existing 80 x 120. All designs would require a double row of acoustic vanes between the test section and fan drive to attenuate fan noise and, in the case of the open-jet designs, to control flow separation at the diffuser downstream end. The inserts would allow virtually anechoic acoustic studies of large helicopter models, jets, and V/STOL aircraft models in simulated flight. Model scale studies would be necessary to optimize the aerodynamic and acoustic performance of any of the designs. In all designs studied, the existing structure would have to be reinforced. Successful development of acoustically transparent walls, though not strictly necessary to the project, would lead to a porous-wall test section that could be substituted for any of the open-jet designs, and thereby eliminate many aerodynamic and acoustic problems characteristic of open-jet shear layers. The larger size of the facility would make installation and removal of the insert components difficult. Consequently, scheduling of the existing 80 x 120 aerodynamic test section and scheduling of the open-jet test section would likely be made on an annual or longer basis. The enhanced wall-lining insert would likely be permanent. Although the modifications are technically feasible, the economic practicality of the project was not evaluated.

Soderman, Paul T.↗
NASA NTRS1990

An enhanced integrated aerodynamic load/dynamic approach to optimum rotor blade design

An enhanced integrated aerodynamic load/dynamic optimization procedure is developed to minimize vibratory root shears and moments. The optimization is formulated with 4/rev vertical and 3/rev inplane shears at the blade root as objective functions and constraints, and 4/rev lagging moment. Constraints are also imposed on blade natural frequencies, weight, autorotational inertia, contrifugal stress, and rotor thrust. The Global Criteria Approach is used for formulating the multi-objective optimization. Design variables include spanwise distributions of bending stiffnesses, torsional stiffness, nonstructural mass, chord, radius of gyration, and blade taper ratio. The program CAMRAD is coupled with an optimizer, which consists of the program CONMIN and an approximate analysis, to obtain optimum designs. The optimization procedure is applied to an advanced rotor as a reference design. Optimum blade designs, obtained with and without a constraint on the rotor thrust, are presented and are compared to the reference blade. Substantial reductions are obtained in the vibratory root forces and moments. As a byproduct, improvements are also found in some performance parameters, such as total power required, which were not considered during optimization.

Chattopadhyay, Aditi↗
NASA NTRS1991

Tailoring of composite wing structures for elastically produced camber deformations

Structural concepts have been created which produce chordwise camber deformation that results in enhanced lift. A wing box can be tailored to utilize these concepts with composites. In attempting to optimize the aerodynamic benefits, it is found that there are two optimum designs that are of interest. There is a 'weight' optimum which corresponds to the maximum lift per unit structural weight. There is also a 'lift' optimum that corresponds to maximum absolute lift. Experience indicates that a large weight penalty accompanies the transition from weight to lift optimum designs. New structural models, the basic deformation mechanisms that are utilized and typical analytical results are presented. It appears that lift enhancements of sufficient magnitude can be produced to render this type of wing tailoring of practical interest.

Rehfield, Lawrence W.↗
NASA NTRS1992

The design of test-section inserts for higher speed aeroacoustic testing in the Ames 80- by 120-foot wind tunnel

An engineering feasibility study was made of aeroacoustic inserts designed for large-scale acoustic research on aircraft models in the 80- by 120-Foot Wind Tunnel at NASA Ames Research Center. The goal was to find test-section modifications that would allow improved aeroacoustic testing at airspeeds equal to and above the current 100 knots limit. Results indicate that the required maximum airspeed drives the design of a particular insert. Using goals of 200, 150, and 100 knots airspeed, the analysis led to a 30 x 60 ft open-jet test section, a 40 x 80 ft open-jet test section, and a 70 x 110 ft closed test section with enhanced wall lining respectively. The open-jet inserts would be composed of a nozzle, collector, diffuser, and acoustic wedges incorporated in the existing 80 x 120 ft test section. The closed test section would be composed of approximately 5-ft acoustic wedges covered by a porous plate attached to the test-section walls of the existing 80 x 120. All designs would require a double row of acoustic vanes between the test section and fan drive to attenuate fan noise and, in the case of the open-jet designs, to control flow separation at the diffuser downstream end. The inserts would allow virtually anechoic acoustics studies of large helicopter models, jets, and V/STOL aircraft models in simulated flight. Model scale studies would be necessary to optimize the aerodynamic and acoustic performance of any of the designs. Successful development of acoustically transparent walls, though not strictly necessary to the project, would lead to a porous-wall test section that could be substituted for any of the open-jet designs, and thereby eliminate many aerodynamic and acoustic problems characteristic of open-jet shear layers.

Soderman, Paul T.↗
NASA NTRS1991

Tailored composite wings with elastically produced chordwise camber

Four structural concepts were created which produce chordwise camber deformation that results in enhanced lift. A wing box can be tailored to utilize each of these with composites. In attempting to optimize the aerodynamic benefits, researchers found that there are two optimum designs that are of interest. There is a weight optimum which corresponds to the maximum lift per unit structural weight. There is also a lift optimum that corresponds to maximum absolute lift. Experience indicates that a large weight penalty accompanies the transition from weight to lift optimum designs. New structural models, the basic deformation mechanisms that are utilized, and typical analytical results are presented. It appears that lift enhancements of sufficient magnitude can be produced to render this type of wing tailoring of practical interest.

Rehfield, Lawrence W.↗
NASA NTRS1992

The design of test-section inserts for higher speed aeroacoustic testing in the Ames 80- by 120-Foot Wind Tunnel

An engineering feasibility study was made of aeroacoustic inserts designed for large-scale acoustic research on aircraft models in the 80- by 120 Foot Wind Tunnel at NASA Ames Research Center. The goal was to find test-section modifications that would allow improved aeroacoustic testing at airspeeds equal to and above the current 100 knots limit. Results indicate that the required maximum airspeed drives the design of a particular insert. Using goals of 200, 150, and 100 knots airspeed, the analysis led to a 30 x 60 ft open-jet test section, a 40 x 80 ft open-jet test section, and a 70 x 110 ft closed test section with enhanced wall lining respectively. The open-jet inserts would be composed of a nozzle, collector, diffuser, and acoustic wedges incorporated in the existing 80 x 120 ft test section. The closed test section would be composed of approximately 5-ft acoustic wedges covered by a porous plate attached to the test-section walls of the existing 80 x 120. All designs would require a double row of acoustic vanes between the test section and fan drive to attenuate fan noise and, in the case of the open-jet designs, to control flow separation at the diffuser downstream end. The inserts would allow virtually anechoic acoustics studies of large helicopter models, jets and V/STOL aircraft models in simulated flight. Model scale studies would be necessary to optimize the aerodynamic and acoustic performance of any of the designs.

Soderman, Paul T.↗
NASA NTRS1997

RIACS

Topics considered include: high-performance computing; cognitive and perceptual prostheses (computational aids designed to leverage human abilities); autonomous systems. Also included: development of a 3D unstructured grid code based on a finite volume formulation and applied to the Navier-stokes equations; Cartesian grid methods for complex geometry; multigrid methods for solving elliptic problems on unstructured grids; algebraic non-overlapping domain decomposition methods for compressible fluid flow problems on unstructured meshes; numerical methods for the compressible navier-stokes equations with application to aerodynamic flows; research in aerodynamic shape optimization; S-HARP: a parallel dynamic spectral partitioner; numerical schemes for the Hamilton-Jacobi and level set equations on triangulated domains; application of high-order shock capturing schemes to direct simulation of turbulence; multicast technology; network testbeds; supercomputer consolidation project.

Oliger, Joseph↗
NASA NTRS1999

Multi-Configuration and Aeroelastic Shape Design

This presentation describes the advances being made with the Aerodynamic Shape Optimization (ASO) and high-fidelity Multidisciplinary Optimization (MDO) software used in the High Speed Research Program at NASA Ames Research Center. The description starts with the motivation for continued ASO/MDO development. Objectives of the current work are then presented. A list of ingredients deemed necessary for a flexible design environment is discussed, and the HSR requirement for different geometries at different design points is explained. Multiple design disciplines within a high-fidelity design environment are demonstrated. Finally, progress so far is summarized and planned future work is outlined.

Reuther, James↗
NASA NTRS2004

Computation of Sensitivity Derivatives of Navier-Stokes Equations using Complex Variables

Accurate computation of sensitivity derivatives is becoming an important item in Computational Fluid Dynamics (CFD) because of recent emphasis on using nonlinear CFD methods in aerodynamic design, optimization, stability and control related problems. Several techniques are available to compute gradients or sensitivity derivatives of desired flow quantities or cost functions with respect to selected independent (design) variables. Perhaps the most common and oldest method is to use straightforward finite-differences for the evaluation of sensitivity derivatives. Although very simple, this method is prone to errors associated with choice of step sizes and can be cumbersome for geometric variables. The cost per design variable for computing sensitivity derivatives with central differencing is at least equal to the cost of three full analyses, but is usually much larger in practice due to difficulty in choosing step sizes. Another approach gaining popularity is the use of Automatic Differentiation software (such as ADIFOR) to process the source code, which in turn can be used to evaluate the sensitivity derivatives of preselected functions with respect to chosen design variables. In principle, this approach is also very straightforward and quite promising. The main drawback is the large memory requirement because memory use increases linearly with the number of design variables. ADIFOR software can also be cumber-some for large CFD codes and has not yet reached a full maturity level for production codes, especially in parallel computing environments.

Vatsa, Veer N.↗
NASA NTRS1998

Preliminary Results from the Application of Automated Adjoint Code Generation to CFL3D

This report describes preliminary results obtained using an automated adjoint code generator for Fortran to augment a widely-used computational fluid dynamics flow solver to compute derivatives. These preliminary results with this augmented code suggest that, even in its infancy, the automated adjoint code generator can accurately and efficiently deliver derivatives for use in transonic Euler-based aerodynamic shape optimization problems with hundreds to thousands of independent design variables.

Carle, Alan↗