SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
New Z-corrections which resulted from recent translator path delay calibrations made at DSS 14, 43, and 63 with newly developed DSN Portable Zero Delay Assemblies are presented. The test results indicate a successful transfer of technology from development to implementation and to the operations phase.
ELF waves which were observed during beam-plasma discharge in the large vacuum chamber at Johnson Space Center are studied. Phase delays as a function of radius (obtained from cross-correlation measurements of density fluctuations) along with measurements of frequency and plasma potential, density, and temperature have been compared to a zero-order slab model of nonlocal azimuthal drift wave propagation. The inferred wave phase velocity in the plasma frame after Doppler correction is found to be near one half the electron diamagnetic drift velocity. Although the measurements presented do not uniquely define a propagation mode, a model of azimuthal drift wave propagation is found to be consistent with observations.
Time-varying spacecraft magnetic fields or stray fields are a problem for magnetometer systems. While constant fields can be removed with zero offset calibration, stray fields are difficult to distinguish from ambient field variations. Putting two magnetometers on a long boom and solving for both the ambient and stray fields can be a good idea, but this gradiometer solution is even more susceptible to noise than a single magnetometer. Unless the stray fields are larger than the magnetometer noise, simply averaging the two measurements is a more accurate approach. If averaging is used, it may be worthwhile to explicitly estimate and remove stray fields. Models and estimation algorithms are provided for solar array, arcjet and reaction wheel fields.
A new approach is presented that uses a weighted least squares fit to analyze wind tunnel strain-gage balance calibration data. The weighted least squares fit is specifically designed to increase the influence of single-component loadings during the regression analysis. The weighted least squares fit also reduces the impact of calibration load schedule asymmetries on the predicted primary sensitivities of the balance gages. A weighting factor between zero and one is assigned to each calibration data point that depends on a simple count of its intentionally loaded load components or gages. The greater the number of a data point's intentionally loaded load components or gages is, the smaller its weighting factor becomes. The proposed approach is applicable to both the Iterative and Non-Iterative Methods that are used for the analysis of strain-gage balance calibration data in the aerospace testing community. The Iterative Method uses a reasonable estimate of the tare corrected load set as input for the determination of the weighting factors. The Non-Iterative Method, on the other hand, uses gage output differences relative to the natural zeros as input for the determination of the weighting factors. Machine calibration data of a six-component force balance is used to illustrate benefits of the proposed weighted least squares fit. In addition, a detailed derivation of the PRESS residuals associated with a weighted least squares fit is given in the appendices of the paper as this information could not be found in the literature. These PRESS residuals may be needed to evaluate the predictive capabilities of the final regression models that result from a weighted least squares fit of the balance calibration data.
One of the major challenges in modeling the magnetospheric magnetic reconnection is to quantify the interaction between large-scale global magnetospheric dynamics and microphysical processes in diffusion regions near reconnection sites. There is still considerable debate as to what degree microphysical processes on kinetic scales affect the global evolution and how important it is to substitute numerical dissipation and/or ad hoc anomalous resistivity by a physically motivated model of dissipation. Comparative studies of magnetic reconnection in small scale geometries demonstrated that MHD simulations that included non-ideal processes in terms of a resistive term $\eta J$ did not produce the fast reconnection rates observed in kinetic simulations. For a broad range of physical parameters in collisionless magnetospheric plasma, the primary mechanism controlling the dissipation in the vicinity of the reconnection site is non-gyrotropic effects with spatial scales comparable with the particle Larmor radius. We utilize the global MHD code BATSRUS and incorporate nongyrotropic effects in diffusion regions in terms of corrections to the induction equation. We developed an algorithm to search for magnetotail reconnection sites, specifically where the magnetic field components perpendicular to the local current direction approaches zero and form an X-type configuration. Spatial scales of the diffusion region and magnitude of the reconnection electric field are calculated selfconsistently using MHD plasma and field parameters in the vicinity of the reconnection site. The location of the reconnection sites is updated during the simulations. To clarify the role of nongyrotropic effects in diffusion region on the global magnetospheric dynamic we perform simulations with steady southward IMF driving of the magnetosphere. Ideal MHD simulations with magnetic reconnection supported by numerical resistivity produce steady configuration with almost stationary near-earth neutral line (NENL). Simulations with non-gyrotropic corrections demonstrate dynamic quasi-periodic response to the steady driving condition. The loading/unloading cycle in non-gyrotropic MHD results has a non-stationary reconnection site in the magnetotail, with the retreating during the stretching phase and then a new NENL forming in the resulting thin plasma sheet. We expect that this model will lead to improved representations of space weather event in the magnetosphere.
The gravitational path integral is usually implemented with a covariant action by analogy with other gauge field theories, but the gravitational case is different in important ways. A key difference is that the integrand has an essential singularity, which occurs at zero lapse where the spacetime metric degenerates. The lapse integration contour required to impose the local time reparametrization constraints must run from − ∞ to + ∞ , yet must not pass through zero. This raises the question: for an application—such as a partition function—where the constraints should be imposed, what is the correct integration contour, and why? We study that question by starting with the reduced phase space path integral, which involves no essential singularity. We observe that if the momenta are to be integrated before the lapse, to obtain a configuration space path integral, the lapse contour should pass below the origin in the complex lapse plane. This contour is also consistent with the requirement that quantum field fluctuation amplitudes have the usual short distance vacuum form, and with obtaining the Bekenstein-Hawking horizon entropy from a Lorentzian path integral. Published by the American Physical Society 2025
Description of Core Under Test (CUT). Magnetics, Inc. 0077894A7 is a powder core material having low loss and high saturation fields. Known for the marketing name Kool Mu, was transformed by taking the known magnetic material, Sendust, and altered the manufacturing process to lower core losses. Possessing these specific properties makes it ideal for power factor correction circuits as well Pulse and Flyback Transformers. In-Line Noise Filters and Inductors are also common due to the near zero magnetostriction. Exhibits a potential saturation induction of 1 T.
Here, we perform the first simultaneous Bayesian parameter inference and optimal reconstruction of the gravitational lensing of the cosmic microwave background (CMB), using 100 deg 2 of polarization observations from the SPTpol receiver on the South Pole Telescope. These data reach noise levels as low as 5.8 μK arcmin in polarization, which are low enough that the typically used quadratic estimator (QE) technique for analyzing CMB lensing is significantly suboptimal. Conversely, the Bayesian procedure extracts all lensing information from the data and is optimal at any noise level. We infer the amplitude of the gravitational lensing potential to be ${A}_{\phi }=0.949\,\pm \,0.122$ using the Bayesian pipeline, consistent with our QE pipeline result, but with 17% smaller error bars. The Bayesian analysis also provides a simple way to account for systematic uncertainties, performing a similar job as frequentist "bias hardening" or linear bias correction, and reducing the systematic uncertainty on A Φ due to polarization calibration from almost half of the statistical error to effectively zero. Finally, we jointly constrain A Φ along with A L , the amplitude of lensing-like effects on the CMB power spectra, demonstrating that the Bayesian method can be used to easily infer parameters both from an optimal lensing reconstruction and from the delensed CMB, while exactly accounting for the correlation between the two. These results demonstrate the feasibility of the Bayesian approach on real data, and pave the way for future analysis of deep CMB polarization measurements with SPT-3G, Simons Observatory, and CMB-S4, where improvements relative to the QE can reach 1.5 times tighter constraints on A Φ and seven times lower effective lensing reconstruction noise.
The structural problems of re-entry occasioned by aerodynamic heating are now generally well known. Typical of these heating problems is the environment experienced by the manned lifting vehicle re-entering from a low altitude orbit. Figure 1 shows typical curves of lower surface temperature as a function of time for a wing loading of 25 Ibs/ft(exp 2), and a lift-drag ratio of 2.5. The two curves cover a practical range of re-entry angles, the lower curve representing an ideal re-entry path with zero dive angle and the upper curve assuming a 2° error in the re-entry angle. Maneuvers for course change or correction are also added to the upper curve. Significant factors from this curve are the relationship between the maximum temperatures and the capabilities of available metallic material, and also the long re-entry time and its effect on total heat load. If a very shallow re-entry is made, maximum lower surface temperatures reach 2000°F which is just within the range of conventional superalloys. To accommodate practical re-entry angles and maneuvers, however, the temperature capability must reach about 2500°F which requires refractory metals. The re-entry time may be as high as 100 minutes, which gives total heat loads of approximately 40,000 BTU/ft(exp 2). A heat load of this magnitude, with equilibrium surface temperatures of the values shown, suggests that a lighter airframe can be constructed by dissipating the heat by radiation from the surface, rather than by absorbing it with a heat sink, or surface cooling, or ablation. Air Force programs to provide airframes for this type of environment have involved the parallel development of a number of different structural concepts. The development to be discussed here was carried out by Bell Aerosystems Company for the Fabrication Branch, Manufacturing Technology Laboratory, Directorate of Materials and Processes, Aeronautical Systems' Division, Wright-Patterson Air Force Base, Ohio, under Contract AF33(600)-40100 (Double-Wall Cooled Structure).
Negative feedback circuit corrects output drift in an electrometer. The negative feedback is used in the no signal state to maintain the output level at zero reference. Drift voltage storage in the signal on state is also used to provide a drift-free readout.
The high altitude aircraft method has been used at NASA GRC since the early 1960's to calibrate solar cell short circuit current, ISC, to Air Mass Zero (AMO). This method extrapolates ISC to AM0 via the Langley plot method, a logarithmic extrapolation to 0 air mass, and includes corrections for the varying Earth-Sun distance to 1.0 AU and compensating for the non-uniform ozone distribution in the atmosphere. However, other characteristics of the solar cell I(V) curve do not extrapolate in the same way. Another approach is needed to extrapolate VOC and the maximum power point (PMAX) to AM0 illumination. As part of the high altitude aircraft method, VOC and PMAX can be obtained as ISC changes during the flight. These values can then the extrapolated, sometimes interpolated, to the ISC(AM0) value. This approach should be valid as long as the shape of the solar spectra in the stratosphere does not change too much from AMO. As a feasibility check, the results are compared to AMO I(V) curves obtained using the NASA GRC X25 based multi-source simulator. This paper investigates the approach on both multi-junction solar cells and sub-cells.
Numerical simulations of fluid flow and collection efficiency for a Science Engineering Associates (SEA) Robust probe are presented. The cases cover a range of freestream velocity from 10-135 m/s, and particle sizes from 1-200 µm. This combination produces results for Stokes numbers in the range of 0.07-1092. A blended modified Stokes (defined in the paper) is introduced which covers a range of 0.07-146. Of particular interest is the collection efficiency of the sensing element (a forward-facing half-pipe), Etot, in the low Stokes number regime. It was observed that the collection efficiency of the sensing area approached one for large Stokes numbers (>100) as expected. As blended modified Stokes number approached one, the Etot dropped to approximately 0.5. By blended modified Stokes numbers of 0.3, the Etot has dropped to essentially zero. Plotting collection versus blended modified Stokes number, the different freestream velocities collapsed quite well on to a single curve. The paper presents a discussion on the flowfield and local collection efficiency, beta, in an effort to explain the predictions. Of particular interest is what is essentially a shadow zone in plain sight. As the Stokes number is reduced, the local beta along the centerline of the half-pipe goes to zero. This occurs at Stokes numbers where the overall collection, Etot, is still appreciable. An empirical relation was developed to allow for corrected collection values at low Stokes numbers. The correlation remains within 2% for blended modified Stokes numbers above 1, and within 6% for all cases.
Numerical simulations of fluid flow and collection efficiency for a Science Engineering Associates (SEA) Robust probe are presented. The cases cover a range of freestream velocity from 10-135 m/s, and particle sizes from 1-200 µm. This combination produces results for Stokes numbers in the range of 0.07-1092. A blended modified Stokes (defined in the paper) is introduced which covers a range of 0.07-146. Of particular interest is the collection efficiency of the sensing element (a forward-facing half-pipe), Etot, in the low Stokes number regime. It was observed that the collection efficiency of the sensing area approached one for large Stokes numbers (>100) as expected. As blended modified Stokes number approached one, the Etot dropped to approximately 0.5. By blended modified Stokes numbers of 0.3, the Etot has dropped to essentially zero. Plotting collection versus blended modified Stokes number, the different freestream velocities collapsed quite well on to a single curve. The paper presents a discussion on the flowfield and local collection efficiency, beta, in an effort to explain the predictions. Of particular interest is what is essentially a shadow zone in plain sight. As the Stokes number is reduced, the local beta along the centerline of the half-pipe goes to zero. This occurs at Stokes numbers where the overall collection, Etot, is still appreciable. An empirical relation was developed to allow for corrected collection values at low Stokes numbers. The correlation remains within 2% for blended modified Stokes numbers above 1, and within 6% for all cases.
Direct electron detectors (DeDs) have been widely used for imaging studies because of their higher beam sensitivity, lower noise, improved pixel resolution, etc. However, there have been limited studies related to the performance in spectroscopic applications for the direct electron detection. Hereby, taking the advantage of the DeD installed on a high-performance electron energy-loss spectrometer, we systematically studied the performance of a DeD (Gatan's K2 IS) fitted on an aberration-corrected transmission electron microscope (TEM) equipped with an electron monochromator. Using SrTiO3 as the model system, the point spread function in the zero-loss region of the spectrum and the performance for core loss spectroscopy have been investigated under both 200 kV and 80 kV operating conditions. We demonstrate that the K2 detector can achieve an overall better performance at 200 kV than a charge coupled device (CCD) detector. At 80 kV, the K2 DeD is still better than a CCD, except for the relative broad tails of the zero-loss peak. The signal-to-noise ratio is very close for DeD and CCD under 80 kV. Based on our data obtained at different operating voltages, it is clear that DeD will benefit the microscopy community and boost the development of cutting-edge materials science studies by pushing the frontiers in electron energy-loss spectroscopy.
We report the first measurement of π 0 production in neutral current (NC) interactions on argon with average neutrino energy of ≲1 GeV. We use data from the MicroBooNE detector’s 85-tonne active volume liquid argon time projection chamber situated in Fermilab’s Booster Neutrino Beam and exposed to 5.89 × 10 20 protons on target for this measurement. Measurements of NC π 0 events are reported for two exclusive event topologies without charged pions. Those include a topology with two photons from the decay of the π 0 and one proton and a topology with two photons and zero protons. Flux-averaged cross-sections for each exclusive topology and for their semi-inclusive combination are extracted (efficiency-correcting for two-plus proton final states), and the results are compared to predictions from the GENIE, NEUT, and NUWRO neutrino event generators. We measure cross sections of 1.243 ± 0.185 (syst) ±0.076 (stat), 0.444 ± 0.098 ± 0.047, and 0.624 ± 0.131 ± 0.075 [10 -38 cm 2 /Ar] for the semi-inclusive NCπ 0 , exclusive NCπ 0 +1p, and exclusive NCπ 0 +0p processes, respectively.
The effect of the set of space flight factors caused a change in the activity of the vestibular apparatus and the spatial perception function. More significant and longer shifts were observed during expeditions of great duration. The detected disorders (increase in reactivity of the otolithic apparatus, decrease in sensitivity of the cupula receptor, deterioration in the perception accuracy, etc.) had a definite tendency to be restored. The primary damage to the otolithic reflex (changes were found in practically all the subjects) is probably caused by the specific effect of zero gravitation, and apparently, may be one of the trigger mechanisms for discrepancy in the activity of the sensory systems, disorders in the correcting function of the cerebellum, and central vestibular formations.
Results of an orbital analysis and performance assessment of SAMSI (Spacecraft Array for Michelson Spatial Interferometry) are presented. The device considered includes two one-meter telescopes in orbits which are identical except for slightly different inclinations; the telescopes achieve separations as large as 10 km and relay starlight to a central station which has a one-meter optical delay line in one interferometer arm. It is shown that a 1000-km altitude, zero mean inclination orbit affords natural scanning of the 10-km baseline with departures from optical pathlength equality which are well within the corrective capacity of the optical delay line. Electric propulsion is completely adequate to provide the required spacecraft motions, principally those needed for repointing. Resolution of 0.00001 arcsec and magnitude limits of 15 to 20 are achievable.
A multigrid-mask method for solution of incompressible Navier-Stokes equations in primitive variable form has been developed. The main objective is to apply this method in conjunction with the pseudospectral element method solving flow past multiple objects. There are two key steps involved in calculating flow past multiple objects. The first step utilizes only Cartesian grid points. This homogeneous or mask method step permits flow into the interior rectangular elements contained in objects, but with the restriction that the velocity for those Cartesian elements within and on the surface of an object should be small or zero. This step easily produces an approximate flow field on Cartesian grid points covering the entire flow field. The second or heterogeneous step corrects the approximate flow field to account for the actual shape of the objects by solving the flow field based on the local coordinates surrounding each object and adapted to it. The noise occurring in data communication between the global (low frequency) coordinates and the local (high frequency) coordinates is eliminated by the multigrid method when the Schwarz Alternating Procedure (SAP) is implemented. Two dimensional flow past circular and elliptic cylinders will be presented to demonstrate the versatility of the proposed method. An interesting phenomenon is found that when the second elliptic cylinder is placed in the wake of the first elliptic cylinder a traction force results in a negative drag coefficient.