Results for “Testing Cooperation” — Page 14

NASA NTRS1979

A progress report on a NASA research program for embedded computer systems software

The paper presents the results of the second stage of the Multipurpose User-oriented Software Technology (MUST) program. Four primary areas of activities are discussed: programming environment, HAL/S higher-order programming language support, the Integrated Verification and Testing System (IVTS), and distributed system language research. The software development environment is provided by the interactive software invocation system. The higher-order programming language (HOL) support chosen for consideration is HAL/S mainly because at the time it was one of the few HOLs with flight computer experience and it is the language used on the Shuttle program. The overall purpose of IVTS is to provide a 'user-friendly' software testing system which is highly modular, user controlled, and cooperative in nature.

Foudriat, E. C.↗

NASA NTRS1987

Expert systems for space power supply - Design, analysis, and evaluation

The feasibility of applying expert systems to the conceptual design, analysis, and evaluation of space power supplies in particular, and complex systems in general is evaluated. To do this, the space power supply design process and its associated knowledge base were analyzed and characterized in a form suitable for computer emulation of a human expert. The existing expert system tools and the results achieved with them were evaluated to assess their applicability to power system design. Some new concepts for combining program architectures (modular expert systems and algorithms) with information about the domain were applied to create a 'deep' system for handling the complex design problem. NOVICE, a code to solve a simplified version of a scoping study of a wide variety of power supply types for a broad range of missions, has been developed, programmed, and tested as a concrete feasibility demonstration.

Cooper, Ralph S.↗

NASA NTRS1992

Development of a machine vision guidance system for automated assembly of space structures

The topics are presented in viewgraph form and include: automated structural assembly robot vision; machine vision requirements; vision targets and hardware; reflective efficiency; target identification; pose estimation algorithms; triangle constraints; truss node with joint receptacle targets; end-effector mounted camera and light assembly; vision system results from optical bench tests; and future work.

Eric G Cooper↗

NASA NTRS1993

Optimization of knowledge-based systems and expert system building tools

The objectives of the NASA-AMES Cooperative Agreement were to investigate, develop, and evaluate, via test cases, the system parameters and processing algorithms that constrain the overall performance of the Information Sciences Division's Artificial Intelligence Research Facility. Written reports covering various aspects of the grant were submitted to the co-investigators for the grant. Research studies concentrated on the field of artificial intelligence knowledge-based systems technology. Activities included the following areas: (1) AI training classes; (2) merging optical and digital processing; (3) science experiment remote coaching; (4) SSF data management system tests; (5) computer integrated documentation project; (6) conservation of design knowledge project; (7) project management calendar and reporting system; (8) automation and robotics technology assessment; (9) advanced computer architectures and operating systems; and (10) honors program.

Yasuda, Phyllis↗

NASA NTRS2001

Preliminary Component Integration Utilizing Rapid Prototyping Techniques

One of the most costly errors committed during the development of an element to be used in the space industry is the lack of communication between design and manufacturing engineers. A very important tool that should be utilized in the development stages by both design and manufacturing disciplines is rapid prototyping. Communication levels are intensified with the injection of functional models that are generated from a drawing. At the Marshall Space Flight Center, this discipline is utilized on a more frequent basis as a manner by which hardware may be tested for design and material compatibility.

Cooper, K.↗

NASA NTRS2004

Test of the Equivalence Principle in an Einstein Elevator

The scientific goal of the experiment is to test the equality of gravitational and inertial mass (i.e., to test the Principle of Equivalence) by measuring the independence of the rate of fall of bodies from the composition of the falling body. The measurement is accomplished by measuring the relative displacement (or equivalently acceleration) of two falling bodies of different materials which are the proof masses of a differential accelerometer. The goal of the experiment is to measure the Eoetvoes ratio sigma g/g (differential acceleration/common acceleration) with an accuracy goal of several parts in 10(exp 15). The estimated accuracy is about two orders of magnitude better than the present state of the art. The main goal of the study to be carried out under this grant is part of the flight definition of the experiment and laboratory testing of key components. The project involves an international cooperation in which the responsibility of the US side is the flight definition of the experimental facility while the responsibility of the non-US partners is the flight definition and laboratory prototyping of the differential acceleration detector.In summary, the experiment to be designed is for taking differential acceleration measurements with a high-sensitivity detector (the sensor) during free fall conditions lasting up to 30 s in a disturbance-free acceleration environment. The experiment strategy consists in letting the sensor free fall inside a few meters long (in the vertical direction) evacuated capsule that is falling simultaneously in the rarefied atmosphere after release from a helium balloon flying at a stratospheric altitude.

Shapiro, Irwin I.↗

NASA NTRS2006

Space Flight Qualification on a Multi-Fiber Ribbon Cable and Array Connector Assembly

NASA's Goddard Space Flight Center (GSFC) cooperatively with Sandia National Laboratories completed a series of tests on three separate configurations of multi-fiber ribbon cable and MTP connector assemblies. These tests simulate the aging process of components during launch and long-term space environmental exposure. The multi-fiber ribbon cable assembly was constructed of non-outgassing materials, with radiation-hardened, graded index 100/140-micron optical fiber. The results of this characterization presented here include vibration testing, thermal vacuum monitoring, and extended radiation exposure testing data.

Xiaodan, Linda Jin↗

NASA NTRS2010

Use of Modal Acoustic Emission to Monitor Damage Progression in Carbon Fiber/Epoxy Tows and Implications for Composite Structures

ASTM-based ILH methods were found to give a reproducible, quantitative estimate of the stress threshold at which significant accumulated damage began to occur. a) FR events are low energy (<2 V(exp 20 microsec) b) FR events occur close to the observed failure locus. c) FR events consist of more than 30% fiber breakage (>300 kHz) d) FR events show a consistent hierarchy of cooperative damage for composite tow, and for the COPV tested, regardless of applied load. Application of ILH or related stress profiles could lead to robust pass/fail acceptance criteria based on the FR. Initial application of FR and FFT analysis of AE data acquired on COPVs is promising.

Waller, Jess M.↗

NASA NTRSDate not supplied

Handling Qualities Assessment of Manual Lunar Landing with Display Augmentation

Research and development is being conducted to support data-driven design decisions for manual control and human involvement in the lunar landing task under the Human Landing System (HLS) program within the Artemis campaign. A human-in-the-loop simulator evaluation of the manual control of a lunar landing vehicle in the final approach and landing phase was conducted at NASA Langley Research Center in the Lunar Flight Deck simulator using the Altair Design and Analysis Cycle (DAC)-2 government reference vehicle. The objective was to perform a direct comparison of control law types with display aiding for various rotational control powers being considered under HLS. Ten subjects (four NASA test pilots and six current pilot astronauts) provided Cooper-Harper ratings, NASA Task Load Index workload ratings, and qualitative comments. The piloting task was to assume manual control of the vehicle (including vertical descent rate) at 150 m above the landing zone, fly to a redesignated landing target (which was up to 75 m radially from the center of the landing zone) and to touch down within a position accuracy of 5m. The data showed that the display augmentation in the form of a “hover cue” significantly improved the pilot’s ability to control translation and create satisfactory handling qualities for otherwise sluggish configurations; however, the investigation also showed that display augmentation is not a panacea. Handling qualities problems, including pilot-induced oscillations, and higher workload for the lowest control powers can still be evident.

Lynda J. Kramer↗

NASA NTRSDate not supplied

Handling Qualities Assessment of Manual Lunar Landing with Display Augmentation

Research and development is being conducted to support data-driven design decisions for manual control and human involvement in the lunar landing task under the Human Landing System (HLS) program within the Artemis campaign. A human-in-the-loop simulator evaluation of the manual control of a lunar landing vehicle in the final approach and landing phase was conducted at NASA Langley Research Center in the Lunar Flight Deck simulator using the Altair Design and Analysis Cycle (DAC)-2 government reference vehicle. The objective was to perform a direct comparison of control law types with display aiding for various rotational control powers being considered under HLS. Ten subjects (four NASA test pilots and six current pilot astronauts) provided Cooper-Harper ratings, NASA Task Load Index workload ratings, and qualitative comments. The piloting task was to assume manual control of the vehicle (including vertical descent rate) at 150 m above the landing zone, fly to a redesignated landing target (which was up to 75 m radially from the center of the landing zone) and to touch down within a position accuracy of 5m. The data showed that the display augmentation in the form of a “hover cue” significantly improved the pilot’s ability to control translation and create satisfactory handling qualities for otherwise sluggish configurations; however, the investigation also showed that display augmentation is not a panacea. Handling qualities problems, including pilot-induced oscillations, and higher workload for the lowest control powers can still be evident.

Lynda Kramer↗

NASA NTRS1998

Flight Testing and Real-Time System Identification Analysis of a UH-60A Black Hawk Helicopter with an Instrumented External Sling Load

Helicopter external air transportation plays an important role in today's world. For both military and civilian helicopters, external sling load operations offer an efficient and expedient method of handling heavy, oversized cargo. With the ability to reach areas otherwise inaccessible by ground transportation, helicopter external load operations are conducted in industries such as logging, construction, and fire fighting, as well as in support of military tactical transport missions. Historically, helicopter and load combinations have been qualified through flight testing, requiring considerable time and cost. With advancements in simulation and flight test techniques there is potential to substantially reduce costs and increase the safety of helicopter sling load certification. Validated simulation tools make possible accurate prediction of operational flight characteristics before initial flight tests. Real time analysis of test data improves the safety and efficiency of the testing programs. To advance these concepts, the U.S. Army and NASA, in cooperation with the Israeli Air Force and Technion, under a Memorandum of Agreement, seek to develop and validate a numerical model of the UH-60 with sling load and demonstrate a method of near real time flight test analysis. This thesis presents results from flight tests of a U.S. Army Black Hawk helicopter with various external loads. Tests were conducted as the U.S. first phase of this MOA task. The primary load was a container express box (CONEX) which contained a compact instrumentation package. The flights covered the airspeed range from hover to 70 knots. Primary maneuvers were pitch and roll frequency sweeps, steps, and doublets. Results of the test determined the effect of the suspended load on both the aircraft's handling qualities and its control system's stability margins. Included were calculations of the stability characteristics of the load's pendular motion. Utilizing CIFER(R) software, a method for near-real time system identification was also demonstrated during the flight test program.

McCoy, Allen H.↗

NASA NTRS1997

Unique Tuft Test Facility Dramatically Reduces Brush Seal Development Costs

Brush seals have been incorporated in the latest turbine engines to reduce leakage and improve efficiency. However, the life of these seals is limited by wear. Studies have shown that optimal sealing characteristics for a brush seal occur before the interference fit between the brush and shaft is excessively worn. Research to develop improved tribopairs (brush and coating) with reduced wear and lower friction has been hindered by the lack of an accurate, low-cost, efficient test methodology. Estimated costs for evaluating a new material combination in an engine company seal test program are on the order of $100,000. To address this need, the NASA Lewis Research Center designed, built, and validated a unique, innovative brush seal tuft tester that slides a single tuft of brush seal wire against a rotating shaft under controlled loads, speeds, and temperatures comparable to those in turbine engines. As an initial screening tool, the brush seal tuft tester can tribologicaly evaluate candidate seal materials for 1/10th the cost of full-scale seal tests. Previous to the development of the brush seal tuft tester facility, most relevant tribological data had been obtained from full-scale seal tests conducted primarily to determine seal leakage characteristics. However, from a tribological point of view, these tests included the confounding effects of varying contact pressures, bristle flaring, high-temperature oxidation, and varying bristle contact angles. These confounding effects are overcome in tuft testing. The interface contact pressures can be either constant or varying depending on the tuft mounting device, and bristle wear can be measured optically with inscribed witness marks. In a recent cooperative program with a U.S. turbine engine manufacturer, five metallic wire candidates were tested against a plasma-sprayed Nichrome-bonded chrome carbide. The wire materials used during this collaboration were either nickel-chrome- or cobaltchrome-based superalloys. These tests corroborated full-scale seal test results and provided insight into previously untested combinations. As the cycle temperature for improved efficiency turbine engines increases, new brush seal materials combinations must be considered. Future brush seal tuft testing will include both metallic and ceramic bristles versus commercial and NASA-developed shaft coatings. The ultimate goal of this work is to expand the current data base so that seal designers can tailor brush seal materials to specific applications.

Fellenstein, James A.↗

NASA NTRS2021

UAS Integration in the NAS Flight Test 6: Full Mission Results

Recent standards development efforts for the integration of Unmanned Aircraft Systems (UAS) into the National Airspace System (NAS) such as those in RTCA Inc. Special Committee 228 (SC-228) have focused on relatively large UAS transitioning to and from Class A airspace. In an effort to expand the range of vehicle classes that can access the NAS, the NASA UAS Integration in the NAS project has investigated Low Size, Weight, and Power (Low SWaP) technologies that would allow smaller UAS to detect-and-avoid (DAA) traffic. Through batch and human in the loop (HITL) simulation studies, the UAS Integration in the NAS DAA subproject have identified candidate performance standards that would contribute to enabling extended Low SWaP, UAS operations under 10,000 feet. These candidate performance standards include minimum field of regard (FOR) values for Low SWaP air surveillance sensors as well as a DAA well-clear (DWC) definition which can be applied to non-cooperative traffic to reduce the required maneuver initiation range. To test the assumptions of the project’s simulation studies and validate the candidate performance standards, a live flight research event was executed at NASA Armstrong Flight Research Center. The UAS Integration in the NAS Project Flight Test 6 Full Mission sought to characterize UAS pilot responses to traffic conflicts using a representative Low SWAP DAA system in an operational NAS environment. To achieve this, live, virtual and constructive distributed environment (LVC-DE) elements were combined to simulate a sector of Oakland center airspace and induce encounters with a live, manned aircraft. A Navmar Applied Sciences Tigershark XP was used as the UAS ownship and was integrated into the test architecture to enable it to be controlled from a Vigilant Spirit Control Station (VSCS) research ground control station. Qualified UAS pilots were recruited to act as subject pilots under test (SPUT) to control the Tigershark XP in a simulated mission while coordinating with a participating air traffic controller in simulated airspace. The intruder speed, intruder equipage and encounter geometry were varied between six scripted encounters per SPUT. Various metrics were collected including pilot reaction time from the onset of DAA alert, ATC coordination rate, probability and severity of losses of DAA well clear, and subjective ratings of system acceptability. The implications of these results on the development of standards for Low SWAP DAA systems will be discussed.

UAV↗

NASA NTRS2002

Test Facilities in Support of High Power Electric Propulsion Systems

Successful development of space fission systems requires an extensive program of affordable and realistic testing. In addition to tests related to design/development of the fission system, realistic testing of the actual flight unit must also be performed. If the system is designed to operate within established radiation damage and fuel burn up limits while simultaneously being designed to allow close simulation of heat from fission using resistance heaters, high confidence in fission system performance and lifetime can be attained through non-nuclear testing. Through demonstration of systems concepts (designed by DOE National Laboratories) in relevant environments, this philosophy has been demonstrated through hardware testing in the High Power Propulsion Thermal Simulator (HPPTS). The HPPTS is designed to enable very realistic non-nuclear testing of space fission systems. Ongoing research at the HPPTS is geared towards facilitating research, development, system integration, and system utilization via cooperative efforts with DOE labs, industry, universities, and other NASA centers. Through hardware based design and testing, the HPPTS investigates High Power Electric Propulsion (HPEP) component, subsystem, and integrated system design and performance.

VanDyke, Melissa↗

NASA NTRSDate not supplied

Roadmap to Cooperative Operating Practices for Strategic Conflict Detection and Resolution in the Upper Class-E Traffic Management Concept

As the governing body of flight operations in the highly anticipated emergent area of Upper Class E airspace (60,000 ft and above), the Federal Aviation Administration (FAA) has recognized the potential for a possible extensible traffic management system for new entrants into this domain. Following the successes with Unmanned Aircraft Systems (UAS) Traffic Management (UTM) and Advanced / Urban Air Mobility (AAM / UAM) Traffic Management programs, FAA put forth an initial concept of operations for supporting the start of the Upper Class E Traffic Management (ETM) concept. Like UTM and AAM / UAM, ETM is envisioned to also be a community-based, industry driven cooperative management concept. However, tailoring it to be adaptable to the atmospheric communication, navigation, and surveillance deficits, as well as the diverse vehicle and mission profiles operating in the ETM environment will be the challenge. As such, the National Aeronautics and Space Administration (NASA) Ames Research Center has been investigating several technologies that will help enable industry in the development of this new type of cooperative operating environment. These technologies are being prototyped and will be tested in a collaborative evaluation of an initial ETM system in late 2023. The evaluation will concentrate on building out ETM system technologies that will inform the participants regarding operational intent sharing, strategic conflict detection, and the resultant deconfliction process. In addition to the technical aspects, key roles and responsibilities will need to be defined. This will be done through exploring community-agreed upon Cooperative Operating Practices (COPs) that include procedures and capabilities to aid in timely, strategic conflict identification and resolution to be developed during the evaluation. As an initial step to the evaluation, the ETM research team at NASA Ames solicited industry feedback on various aspects of ETM operations from subject matter experts. A virtual tabletop walkthrough session was held over a two-day period to follow a roadmap through the functional steps needed to build COPs, focusing on strategic conflict detection and resolution. Overall, the ETM tabletop provided insights into how the community wanted to instantiate the generation and sharing of operational intent, detect strategic conflicts and resolve those conflicts using a preliminary set of procedural community-agreed upon COPs.

Upper Class-E Traffic Management (ETM)↗

NASA NTRSDate not supplied

Roadmap to Cooperative Operating Practices for Strategic Conflict Detection and Resolution in the Upper Class E Traffic Management Concept

As the governing body of flight operations in the highly anticipated emergent area of Upper Class E airspace (60,000 ft and above), the Federal Aviation Administration (FAA) has recognized the potential for a possible extensible traffic management system for new entrants into this domain. Following the successes with Unmanned Aircraft Systems (UAS) Traffic Management (UTM) and Advanced / Urban Air Mobility (AAM / UAM) Traffic Management programs, FAA put forth an initial concept of operations for supporting the start of the Upper Class E Traffic Management (ETM) concept. Like UTM and AAM / UAM, ETM is envisioned to also be a community-based, industry driven cooperative management concept. However, tailoring it to be adaptable to the atmospheric communication, navigation, and surveillance deficits, as well as the diverse vehicle and mission profiles operating in the ETM environment will be the challenge. As such, the National Aeronautics and Space Administration (NASA) Ames Research Center has been investigating several technologies that will help enable industry in the development of this new type of cooperative operating environment. These technologies are being prototyped and will be tested in a collaborative evaluation of an initial ETM system in late 2023. The evaluation will concentrate on building out ETM system technologies that will inform the participants regarding operational intent sharing, strategic conflict detection, and the resultant deconfliction process. In addition to the technical aspects, key roles and responsibilities will need to be defined. This will be done through exploring community-agreed upon Cooperative Operating Practices (COPs) that include procedures and capabilities to aid in timely, strategic conflict identification and resolution to be developed during the evaluation. As an initial step to the evaluation, the ETM research team at NASA Ames solicited industry feedback on various aspects of ETM operations from subject matter experts. A virtual tabletop walkthrough session was held over a two-day period to follow a roadmap through the functional steps needed to build COPs, focusing on strategic conflict detection and resolution.

Upper Class E Traffic Management (ETM)↗

NASA NTRS1996

The First Joint Report of the General Thomas P. Stafford Task Force and the Academician Vladimir F. Utkin Advisory Expert Council on the Shuttle-Mir Rendezvous and Docking Missions

In October 1992, the National Aeronautics and Space Administration (NASA) and the Russian Space Agency (RSA) formally agreed to conduct a fundamentally new program of human cooperation in space. The 'Shuttle-Mir Program' encompassed combined astronaut-cosmonaut activities on the Shuttle, Soyuz Test Module(TM), and Mir station spacecraft. At that time, NASA and RSA limited the project to: the STS-60 mission carrying the first Russian cosmonaut to fly on the U.S. Space Shuttle; the launch of the first U.S. astronaut on the Soyuz vehicle for a multi-month mission as a member of a Mir crew; and the change-out of the U.S.-Russian Mir crews with a Russian crew during a Shuttle rendezvous and docking mission with the Mir Station. The objectives of the Phase 1 Program are to provide the basis for the resolution of engineering and technical problems related to the implementation of the ISS and future U.S.-Russian cooperation in space. This, combined with test data generated during the course of the Shuttle flights to the Mir station and extended joint activities between U.S. astronauts and Russian cosmonauts aboard Mir, is expected to reduce the technical risks associated with the construction and operation of the ISS. Phase 1 will further enhance the ISS by combining space operations and joint space technology demonstrations. Phase 1 also provides early opportunities for extended U.S. scientific and research activities, prior to utilization of the ISS.

Source record↗

NASA NTRS1983

AD-1 oblique wing research aircraft pilot evaluation program

A flight test program of a low cost, low speed, manned, oblique wing research airplane was conducted at the NASA Dryden Flight Research Facility in cooperation with NASA Ames Research Center between 1979 and 1982. When the principal purpose of the test program was completed, which was to demonstrate the flight and handling characteristics of the configuration, particularly in wing-sweep-angle ranges from 45 to 60 deg, a pilot evaluation program was conducted to obtain a qualification evaluation of the flying qualities of an oblique wing aircraft. These results were documented for use in future studies of such aircraft.

Painter, W. D.↗