Investigation of magnetically soft, high-temperature cobalt-iron alloy
Magnetically soft, high temperature cobalt-iron alloy
MAGNETIC MATERIAL↗
SEARCH · Engineering Papers
Results for “Soft materials”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Effects of Io ejecta on Europa
The effects of plasma ejected from Io on the nature and evolution of the surface of Europa and on the relative importance of the roles played by the two satellites in the Jupiter magnetosphere are examined. Observations of an ultraviolet absorption feature on the trailing side of Europa are interpreted as due to an equilibrium column density of SO2 in a steady-state model of the implantation of iogenic ions into the surface of Europa and their subsequent sputtering. The observed sulfur column density of 2 x 10 to the 16th/sq cm implies a slow loss of material from Europa, mainly water ice, and indicates that the spectrum of particles sputtered is soft. Considerations of the comparative roles of corotating and energetic heavy ions are shown to suggest that the implantation and sputtering is primarily the result of the proton and light ion component of the plasma. The weakness of Europa as a plasma source resulting from the soft sputtered particle spectrum thus leads to the dominance of Io in contributing to the magnetospheric plasma.
Eviatar, A.↗
Theoretical investigation of wave-vector-dependent analytical and numerical formulations of the interband impact-ionization transition rate for electrons in bulk silicon and GaAs
The electron interband impact-ionization rate for both silicon and gallium arsenide is calculated using an ensemble Monte Carlo simulation with the expressed purpose of comparing different formulations of the interband ionization transition rate. Specifically, three different treatments of the transition rate are examined: the traditional Keldysh formula, a new k-dependent analytical formulation first derived by W. Quade, E. Scholl, and M. Rudan (1993), and a more exact, numerical method of Y. Wang and K. F. Brennan (1994). Although the completely numerical formulation contains no adjustable parameters and as such provides a very reliable result, it is highly computationally intensive. Alternatively, the Keldysh formular, although inherently simple and computationally efficient, fails to include the k dependence as well as the details of the energy band structure. The k-dependent analytical formulation of Quade and co-workers overcomes the limitations of both of these models but at the expense of some new parameterization. It is found that the k-dependent analytical method of Quade and co-workers produces very similar results to those obtained with the completely numerical model for some quantities. Specifically, both models predict that the effective threshold for impact ionization in GaAs and silicon is quite soft, that the majority of ionization events originate from the second conduction band in both materials, and that the transition rate is k dependent. Therefore, it is concluded that the k-dependent analytical model can qualitatively reproduce results similar to those obtained with the numerical model yet with far greater computational efficiency. Nevertheless, there exist some important drawbacks to the k-dependent analytical model of Quade and co-workers: These are that it does not accurately reproduce the quantum yield data for bulk silicon, it requires determination of a new parameter, related physically to the overlap intergrals of the Bloch state which can only be adjusted by comparison to experiment, and fails to account for any wave-vector dependence of the overlap integrals. As such the transition rate may be overestimated at those points for which 'near vertical,' small change in k, transitions occur.
Kolnik, Jan↗
Theoretical Investigation of Wave-Vector-Dependent Analytical and Numerical Formulations of the Interband Impact-Ionization Transition Rate for Electron in Bulk Silicon and GaAs
The electron interband impact-ionization rate for both silicon and gallium arsenide is calculated using an ensemble Monte Carlo simulation with the expressed purpose of comparing different formulations of the interband ionization transition rate. Specifically, three different treatments of the transition rate are examined: the traditional Keldysh formula, a new k-dependent analytical formulation first derived by W. Quade, E Scholl, and M. Rudan, and a more exact, numerical method of Y. Wang and K. F. Brennan. Although the completely numerical formulation contains no adjustable parameters and as such provides a very reliable result, it is highly computationally intensive. Alternatively, the Keldysh formula, although inherently simple and computationally efficient, fails to include the k dependence as well as the details of the energy band structure. The k-dependent analytical formulation of Quade and co-workers overcomes the limitations of both of these models but at the expense of some new parameterization. It is found that the k-dependent analytical method of Quade and co-workers produces very similar results to those obtained with (he completely numerical model for some quantities. Specifically, both models predict that the effective threshold for impact ionization in GaAs and silicon is quite soft, that the majority of ionization events originate from the second conduction band in both materials, and that the transition rate is k dependent. Therefore, it is concluded that the k-dependent analytical model can qualitatively reproduce results similar to those obtained with the numerical model yet with far greater computational efficiency. Nevertheless, there exist some important drawbacks to the k-dependent analytical model of Quade and co-workers: These are that it does not accurately reproduce the quantum yield data for bulk silicon, it requires determination of a new parameter, related physically to (he overlap integrals of the Bloch state which can only be adjusted by comparison to experiment, and fails to account for any wave-vector dependence of the overlap integrals. As such [he transition rate may be overestimated at those points for which "near vertical," small change in k, transitions occur.
Kolnik, Jan↗
The Broad Absorption Line Tidal Disruption Event iPTF15af: Optical and Ultraviolet Evolution
We present multiwavelength observations of the tidal disruption event (TDE) iPTF15af, discovered by the intermediate Palomar Transient Factory survey at redshift z = 0.07897. The optical and ultraviolet (UV) light curves of the transient show a slow decay over 5 months, in agreement with previous optically discovered TDEs. It also has a comparable blackbody peak luminosity of L(sub peak) approx. = 1.5 x 10(exp 44) erg s(exp -1). The inferred temperature from the optical and UV data shows a value of (3–5) × 10(exp 4) K. The transient is not detected in X-rays up to L(sub X) < 3 x 10(exp 42) erg s(exp -1) within the first 5 months after discovery. The optical spectra exhibit two distinct broad emission lines in the He ii region, and at later times also Hα emission. Additionally, emission from [N iii] and [O iii] is detected, likely produced by the Bowen fluorescence effect. UV spectra reveal broad emission and absorption lines associated with high-ionization states of N v, C iv, Si iv, and possibly P v. These features, analogous to those of broad absorption line quasars (BAL QSOs), require an absorber with column densities N(sub H) > 10(exp 23) cm(exp -2). This optically thick gas would also explain the nondetection in soft X-rays. The profile of the absorption lines with the highest column density material at the largest velocity is opposite that of BAL QSOs. We suggest that radiation pressure generated by the TDE flare at early times could have provided the initial acceleration mechanism for this gas. Spectral UV line monitoring of future TDEs could test this proposal.
Blagorodnova, N.↗
Sapphire Viewports for a Venus Probe
A document discusses the creation of a viewport suitable for use on the surface of Venus. These viewports are rated for 500 C and 100 atm pressure with appropriate safety factors and reliability required for incorporation into a Venus Lander. Sapphire windows should easily withstand the chemical, pressure, and temperatures of the Venus surface. Novel fixture designs and seals appropriate to the environment are incorporated, as are materials compatible with exploration vessels. A test cell was fabricated, tested, and leak rate measured. The window features polish specification of the sides and corners, soft metal padding of the sapphire, and a metal C-ring seal. The system safety factor is greater than 2, and standard mechanical design theory was used to size the window, flange, and attachment bolts using available material property data. Maintenance involves simple cleaning of the window aperture surfaces. The only weakness of the system is its moderate rather than low leak rate for vacuum applications.
Bates, Stephen↗
Soft-Robotic Rover with Electrodynamic Power Scavenging: NIAC Final Report - Phase 1
The purpose of studying the capabilities of Electrodynamic Tethers (EDT) and Soft Robotics is to ascertain the feasibility of using cross-cutting EDT and soft robotics technologies to achieve future NASA mission objectives with mass and power budgets orders of magnitude lower than conventional spacecraft. In this context, the Phase I study focuses on three technological elements: the design of a soft-robotic rover that can operate in extraterrestrial oceans, demonstrating feasibility of electrodynamic tethers for power scavenging in the Europa environment, and utilizing electrolysis to power biomimetic propulsion.The Phase I results show that a soft robotic, underwater rover has many advantages over a traditional view of autonomous underwater vehicles. Many of these advantages stem from its ability to collapse or expand the body, which carries two key benefits: (i) cost savings in transport and (ii) buoyancy control. Furthermore, this rover's material offers properties that enable it to survive most oceanic conditions, withstand a likely radiation environment, and retard ice formation. The use of these soft robots under water is very attractive because buoyancy enables very large robots without the need for skeletal structures that limit their shape-changing ability. The prime limitation of soft robots for underwater exploration is their nascent state of development, an issue that this study has begun to address and that we hope to continue in Phase II. The theoretical calculations and experimental investigation on electrodynamic tethers discussed in this report show that their use in saltwater environments is feasible. However, magneto hydrodynamic effects require attention, which will be a priority in Phase II. A possible approach involves magnetic shielding of a portion of the EDT array to generate significant current from imposed alternating magnetic fields. The Phase I experiments show that this approach may enable enough power to be generated for a soft robotic rover of the scale contemplated here. This power is in the range of 1mW to 1W and determines the time required to collect and transmit science data.
Soft Robotics↗
Development of high-speed balancing technology
An investigation into laser material removal showed that laser burns act in a manner typical of mechanical stress raisers causing a reduction in fatigue strength; the fatigue strength is lowered relative to the smooth specimen fatigue strength. Laser-burn zones were studied for four materials: Alloy Steel 4340, Stainless Steel 17-4 PH, Inconel 718, and Aluminum Alloy 6061-T6. Calculations were made of stress concentration factors K, for laser-burn grooves of each material type. A comparison was then made to experimentally determine the fatigue strength reduction factor. These calculations and comparisons indicated that, except for the 17-4 PH material, good agreement (a ratio of close to 1.0) existed between Kt and Kf. The performance of the 17-4 PH material has been attributed to early crack initiation due to the lower fatigue resistance of the soft, unaged laser-affected zone. Also covered in this report is the development, implementation, and testing of an influence coefficient approach to balancing a long, slender shaft under applied-torque conditions. Excellent correlation existed between the analytically predicted results and those data obtained from testing.
Demuth, R.↗
Kinematical analysis of flare spray ejecta observed in the corona
Observations in H-alpha, soft X-ray, white light and radio wavelengths are used to track cool and hot material from limb de-occultation to the extent of six solar radii. The kinematics and thermodynamics of the internal material are determined, along with the overall mass and energy budget of the event. It is found that the majority of the mass and energy is linked with the coronal material, but at least 20% of the ejected mass originated as near-surface prominence material, leading to the conclusions that the upper part of the prominence was being heated to coronal temperatures as it rose through the corona. Evidence was found that a moving type IV burst, indicative of strong magnetic fields, was associated with the upper part of the prominence, and the observations are judged to be most consistent with magnetic propulsion models of coronal transients.
Webb, D. F.↗
A magnetostatic-coupling based remote query sensor for environmental monitoring
A new type of in situ, remotely monitored magnetism-based sensor is presented that is comprised of an array of magnetically soft, magnetostatically-coupled ferromagnetic thin-film elements or particles combined with a chemically responsive material that swells or shrinks in response to the analyte of interest. As the chemically responsive material changes size the distance between the ferromagnetic elements changes, altering the inter-element magnetostatic coupling. This in turn changes the coercive force of the sensor, the amplitude of the voltage spikes detected in nearby pick-up coils upon magnetization reversal and the number of higher-order harmonics generated by the flux reversal. Since the sensor is monitored through changes in magnetic flux, no physical connections such as wires or cables are needed to obtain sensor information, nor is line of sight alignment required as with laser telemetry; the sensors can be detected from within sealed, opaque or thin metallic enclosures.
NASA Discipline Life Sciences Technologies↗
Damage Detection and Self-Repair in Inflatable/Deployable Structures
Inflatable/deployable structures are under consideration for applications as varied as expansion modules for the International Space Station to destinations for space tourism to habitats for the lunar surface. Monitoring and maintaining the integrity of the physical structure is critical, particularly since these structures rely on non-traditional engineering materials such as fabrics, foams, and elastomeric polymers to provide the primary protection for the human crew. The closely related prior concept of monitoring structural integrity by use of built-in or permanently attached sensors has been applied to structures made of such standard engineering materials as metals, alloys, and rigid composites. To effect monitoring of flexible structures comprised mainly of soft goods, however, it will be necessary to solve a different set of problems - especially those of integrating power and data-transfer cabling that can withstand, and not unduly interfere with, stowage and subsequent deployment of the structures. By incorporating capabilities for self-repair along with capabilities for structural health monitoring, successful implementation of these technologies would be a significant step toward semi-autonomous structures, which need little human intervention to maintain. This would not only increase the safety of these structures, but also reduce the inspection and maintenance costs associated with more conventional structures.
Brandon, Erik↗
Finite-Element Methods for Real-Time Simulation of Surgery
Two finite-element methods have been developed for mathematical modeling of the time-dependent behaviors of deformable objects and, more specifically, the mechanical responses of soft tissues and organs in contact with surgical tools. These methods may afford the computational efficiency needed to satisfy the requirement to obtain computational results in real time for simulating surgical procedures as described in Simulation System for Training in Laparoscopic Surgery (NPO-21192) on page 31 in this issue of NASA Tech Briefs. Simulation of the behavior of soft tissue in real time is a challenging problem because of the complexity of soft-tissue mechanics. The responses of soft tissues are characterized by nonlinearities and by spatial inhomogeneities and rate and time dependences of material properties. Finite-element methods seem promising for integrating these characteristics of tissues into computational models of organs, but they demand much central-processing-unit (CPU) time and memory, and the demand increases with the number of nodes and degrees of freedom in a given finite-element model. Hence, as finite-element models become more realistic, it becomes more difficult to compute solutions in real time. In both of the present methods, one uses approximate mathematical models trading some accuracy for computational efficiency and thereby increasing the feasibility of attaining real-time up36 NASA Tech Briefs, October 2003 date rates. The first of these methods is based on modal analysis. In this method, one reduces the number of differential equations by selecting only the most significant vibration modes of an object (typically, a suitable number of the lowest-frequency modes) for computing deformations of the object in response to applied forces.
Basdogan, Cagatay↗
Soft container for explosive nuts
Flexible fabric fits over variety of assembly shapes to contain debris produced by detonations or safety tests. Bag material is woven multifilament polyamide or aramid. Belt loops hold bag to clamp. Ring supports explosive nut structure and detonator wires, and after nut is mounted, bag and clamp are slipped over ring and fastened.
Glenn, D. C.↗
Excessive production of electron pairs by soft photons in low multiplicity ion interactions
Three multiply charged primary cosmic ray interactions with carbon nuclei are reported, in which the number of materialized electron pairs within a distance of about 0.3 conversion length is larger than predicted from isospin considerations. These are the most energetic (sigma E gamma 4 TeV) of the low multiplicity ( 15 tracks) events observed in the Japanese-American Cooperative Experiment (JACEE-2) emulsion chamber.
Burnett, T. H.↗
Gage of 6.5 per cent Si-Fe sheet is chemically reduced
Chemical milling process aids the production of 6.5 percent silicon-iron soft magnetic-alloy sheets to very thin gages. Following conventional rolling to safe gage limits, the material is chemically reduced to the desired gage.
Goldman, A.↗
The relationship between hard and soft X-ray bursts observed by OSO 7
The paper reviews the observations of solar X-rays in the range 1-100 keV made by the solar X-ray instrument on board the OSO-7 satellite and explores the relationship between the hard and soft X-ray components in order to glean some information on the physics of solar flares. Some of the results are as follows: The growth of the soft X-ray emission in a burst must be due to the addition of new hot material to the flare plasma. The anticorrelation between cooling time and maximum plasma temperature gives new evidence to support conduction as the principal cooling mechanism of the hot flare plasma. Observations of hard X-ray emission from bursts which occurred behind the limb indicate that hard X-ray emission comes at least in part from considerable heights in the corona.
Datlowe, D. W.↗
Tensile Properties of Hydrogels and of Snake Skin
Stimulus-responsive or 'smart' gels are of potential interest as sensors and actuators, in industrial separations, and as permeable delivery systems. In most applications, a certain degree of mechanical strength and toughness will be required, yet the large-strain behavior of gels has not been widely reported. Some exceptions include work on gelatin and other food gels, some characterization of soft gels applicable for in-vitro cell growth studies, and toughness determinations on commercial contact lens materials. In general, it can be anticipated that the gel stiffness will increase with increasing degree of crosslinking, but the tensile strength may go through a maximum. Gel properties can be tailored by varying not only the degree of crosslinking, but also the polymer concentration and the nature of the polymer backbone (e.g. its stiffness or solubility). Polypeptides provide an especially interesting case, where secondary structure affects trends in moduli and conformational transitions may accompany phase changes. A few papers on the tensile properties of responsive gels have begun to appear. The responsive hydrogel chosen for the present study, crosslinked hydroxypropylcellulose, shrinks over a rather narrow temperature range near 44 C. Some vertebrate skin is also subject to substantial strain. Among reptiles, the morphologies of the skin and scales show wide variations. Bauer et al. described the mechanical properties and histology of gecko skin; longitudinal tensile properties of snake skin were examined by Jayne with reference to locomotion. The present measurements focus on adaptations related to feeding, including the response of the skin to circumferential tension. Tensile properties will be related to interspecific and regional variation in skin structure and folding.
Hinkley, Jeffrey A.↗
Meta-aerogels: Auxetic Shape-memory Polyurethane Aerogels
Shape-memory poly(isocyanurate-urethane) (PIR-PUR) aerogels are low-density monolithic nanoporous solids that remember and return to their permanent shape through a heating actuation step. Herein, through structural design at the macro scale, the shape-memory response is augmented with an auxetic effect manifested by a negative Poisson’s ratio of approximately -0.8 at 15% compressive strain. Thus, auxetic shape-memory PIR-PUR monoliths experience volume contraction upon compression at a temperature above the glass transition temperature of the base polymer (Tg ~ 30 °C), and they can be stowed indefinitely in that temporary shape by cooling below Tg. By heating back above Tg, the compressed/shrunk form expands back to their original shape/size. This technology is relevant to a broad range of industries spanning the commercial, aeronautical, and aerospace sectors. The materials are referred to as meta-aerogels and their potential applications include minimally invasive medical devices, soft robotics, and in situations where volume is at a premium, as for example for storage of deployable space structures and planetary habitats during transport to the point of service.
Sadeq Malakooti↗