Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SOLVENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Solvent Hold Tank Sample Results for MCU-20-32-33-34 (Quarterly Report, September 2020)

In late FY13, MCU implemented the Next Generation Solvent (NGS) flow sheet. Facility personnel added a non-radioactive, NGS “cocktail” containing the new Extractant (MaxCalix) and a new Suppressor (TiDG) to the SHT heel to implement the NGS flow sheet. The resulting “blend” solvent (“NGS blend solvent”) is essentially NGS with residual amounts of calix[4]arene-bis(tert-octylbenzo-crown-6) (BOBCalixC6) and trioctylamine (TOA). For process monitoring, SHT samples are sent to Savannah River National Laboratory (SRNL) to examine solvent composition changes over time. With the exception of Isopar™ L which is regularly added to the SHT due to its high vapor pressure, this report shows the cumulative chemical composition data, including impurities like mercury, of the September 2020 (MCU-20-32-33-34) solvent SHT sample. A summary report of the September SHT solvent sample was issued earlier. This report examines the cumulative results from these and several past monthly reports. These samples are intended to verify that the solvent is within the specified composition range. A baseline “scratch” solvent - a scratch solvent is a preparation of all 6 solvent components (this includes the old extractant BoBCalix and the old suppressor TrioctylAmine that remained when solvent was converted to Next Generation Solvent [NGS]) of the composition that approximates the blend of cocktail and heel solvent - was prepared in the lab (September 2018) and used for comparison and evaluation. The results from the analyses are presented in this document. This report is the last characterization analysis of the SHT solvent. MCU entered a lay-up state and about 128 gallons of the SHT solvent were pumped into 55 gallons drums for future disposal.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Integrated Polymer Dissolution and Solution Blow Spinning Coupled with Solvent Recovery for Expanded Polystyrene Recycling

With increasing buoyant plastic wastes entering into oceans and food chains, the disposal and recycling of waste expanded polystyrene (WPS) has become an imminent environmental problem. In this work, a recycling scheme for waste WPS is proposed that combines the polymer dissolution recycling approach with the solution blow spinning (SBS) technique that facilitates the high-volume bulk WPS transportation and the value-addition of WPS to nanofibers. Solvent selection is critical for an economical and environmentally favorable implementation of this recycling scheme at large scale. Here, the effect of three solvents with distinct volatility, viz. ethyl acetate, toluene, and N, N- dimethylformamide (DMF) have been studied on the fiber formation and the ease of the solvent recovery, in order to ascertain the practicability of using these solvents for the recycling process. The fiber formation is experimentally demonstrated for the WPS-solvent systems using the SBS process. It is found that the fiber morphology varies for the different WPS-solvent systems. A solvent recovery scheme to recover the solvent from the air-solvent mixture (leaving SBS) is evaluated using ASPEN Plus simulation. The % solvent recovery is determined as a function of the required energy input for different process parameters including compressor pressure and air to polymer solution feed ratio. The simulation studies show that a lower feed air to polymer solution ratio and higher compressor pressure are required to obtain > 70% solvent recovery for high volatility solvents (ethyl acetate and toluene) with lower energy input and optimal operating condenser temperature (~ 0 °C). Conversely, significant solvent losses occur in the SBS process with a lower volatility solvent (DMF), leading to a lower solvent recovery for the whole process. The % DMF recovery can be improved upon by using higher feed air to polymer solution ratio although at a higher energy penalty.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Absorption rates of carbon dioxide in amines in hydrophilic and hydrophobic solvents

The rate of absorption of CO 2 into amines in hydrophilic and hydrophobic solvent mixtures was studied in this work using a stopped-flow apparatus and a stirred-tank reactor. Monoethanolamine (MEA, primary amine) and N-methyl benzylamine (NMBZA, aromatic secondary amine) are chosen for this study and diluted in hydrophobic or hydrophilic solvents at different temperatures (295–343 K) and concentrations (0.01–4 kmol.m -3 ). It was found that the reaction rate between the secondary amine and CO 2 in water is faster than the reaction with the linear primary amine (MEA); however, in an ethereal hydrophobic non-aqueous system the NMBZA-CO 2 reaction is slower than the reaction of CO 2 with MEA. With respect to amine, the reaction orders were found to be 0.9 and 1.2 for hydrophilic systems (MEA + H 2 O, NMBZA + H 2 O). For hydrophobic system they were found to be 0.6 and 2.7 (NMBZA + ethereal hydrophobic solvent, NMBZA + MePhOH + ethereal hydrophobic solvent). When amine was mixed with hydrophilic solvent (H 2 O), the activation energy of amine (NMBZA) to react with CO 2 was found to be 27.66 kJ.mol -1 and decreased to 10.37 kJ.mol -1 when mixed with hydrophobic solvent (ethereal hydrophobic solvent). The activation energy of hydrophobic solvent was found to increase by adding an alcohol to the solvent (MePhOH + ethereal hydrophobic solvent). Both the zwitterion and termolecular mechanism were applied to the experimental data. It was found that deprotonation of the zwitterion and deprotonation of the loosely bound complex was the rate limiting step for the zwitterion and termolecular mechanism, respectively. In addition, activators such as water, piperazine (PZ), and 4-hydroxy piperidinol (HPIP) were added to the ethereal hydrophobic non-aqueous solvent to determine the effect on the reaction rate. It was found that the water- and amine-based activators lead to an increase in the observed reaction rates as the concentration of the activators increased. The reaction of NMBA with CO 2 and PZ exhibited a higher reaction rate but the PZ was insoluble in the non-aqueous NMBZA system, whereas HPIP remained soluble and offered a similar reaction rate. The activation energy of ethereal hydrophobic non-aqueous solvent to react with CO 2 increased from 27.98 to 32.83 kJ.mol -1 by adding PZ and 33.51 kJ.mol -1 by HPIP and remained by adding H 2 O (26.78 kJ.mol -1 ). From this work, it was found that the non-aqueous solvent plays an important role in the reaction rate of CO 2 with amines. Activators and solvents can be selected to increase the reaction rate with CO 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nonadiabatic dynamics of electron transfer in solution: Explicit and implicit solvent treatments that include multiple relaxation time scales

The development of efficient theoretical methods for describing electron transfer (ET) reactions in condensed phases is important for a variety of chemical and biological applications. Previously, dynamical dielectric continuum theory was used to derive Langevin equations for a single collective solvent coordinate describing ET in a polar solvent. In this theory, the parameters are directly related to the physical properties of the system and can be determined from experimental data or explicit molecular dynamics simulations. Herein, we combine these Langevin equations with surface hopping nonadiabatic dynamics methods to calculate the rate constants for thermal ET reactions in polar solvents for a wide range of electronic couplings and reaction free energies. Comparison of explicit and implicit solvent calculations illustrates that the mapping from explicit to implicit solvent models is valid even for solvents exhibiting complex relaxation behavior with multiple relaxation time scales and a short-time inertial response. The rate constants calculated for implicit solvent models with a single solvent relaxation time scale corresponding to water, acetonitrile, and methanol agree well with analytical theories in the Golden rule and solvent-controlled regimes, as well as in the intermediate regime. The implicit solvent models with two relaxation time scales are in qualitative agreement with the analytical theories but quantitatively overestimate the rate constants compared to these theories. Analysis of these simulations elucidates the importance of multiple relaxation time scales and the inertial component of the solvent response, as well as potential shortcomings of the analytical theories based on single time scale solvent relaxation models. This implicit solvent approach will enable the simulation of a wide range of ET reactions via the stochastic dynamics of a single collective solvent coordinate with parameters that are relevant to experimentally accessible systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

On the theory of electric double layer with explicit account of a polarizable co-solvent

We present a continuation of our theoretical research into the influence of co-solvent polarizability on a differential capacitance of the electric double layer. We formulate a modified Poisson-Boltzmann theory, using the formalism of density functional approach on the level of local density approximation taking into account the electrostatic interactions of ions and co-solvent molecules as well as their excluded volume. We derive the modified Poisson-Boltzmann equation, considering the three-component symmetric lattice gas model as a reference system and minimizing the grand thermodynamic potential with respect to the electrostatic potential. We apply present modified Poisson-Boltzmann equation to the electric double layer theory, showing that accounting for the excluded volume of co-solvent molecules and ions slightly changes the main result of our previous simplified theory. Namely, in the case of small co-solvent polarizability with its increase under the enough small surface potentials of electrode, the differential capacitance undergoes the significant growth. Oppositely, when the surface potential exceeds some threshold value (which is slightly smaller than the saturation potential), the increase in the co-solvent polarizability results in a differential capacitance decrease. However, when the co-solvent polarizability exceeds some threshold value, its increase generates a considerable enhancement of the differential capacitance in a wide range of surface potentials. We demonstrate that two qualitatively different behaviors of the differential capacitance are related to the depletion and adsorption of co-solvent molecules at the charged electrode. We show that an additive of the strongly polarizable co-solvent to an electrolyte solution can shift significantly the saturation potential in two qualitatively different manners. Namely, a small additive of strongly polarizable co-solvent results in a shift of saturation potential to higher surface potentials. On the contrary, a sufficiently large additive of co-solvent shifts the saturation potential to lower surface potentials. We obtain that an increase in the co-solvent polarizability makes the electrostatic potential profile longer-ranged. However, increase in the co-solvent concentration in the bulk leads to non-monotonic behavior of the electrostatic potential profile. An increase in the co-solvent concentration in the bulk at its sufficiently small values makes the electrostatic potential profile longer-ranged. Oppositely, when the co-solvent concentration in the bulk exceeds some threshold value, its further increase leads to decrease in electrostatic potential at all distances from the electrode.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

ODC-Free Solvent Implementation Issues for Vulcanized Rubber and Bond Systems

Thiokol Propulsion has worked extensively to replace 1,1,1-trichloroethane (TCA) with ozone depleting chemicals (ODC)-free solvents for use in the manufacture of the Reusable Solid Rocket Motor (RSRM) for the Space Shuttle Program. As Thiokol has transitioned from sub-scale to full-scale testing and implementation of these new solvents, issues have been discovered which have required special attention. The original intent of Thiokol's solvent replacement strategy was to replace TCA with a single drop-in solvent for all equivalent applications. We have learned that a single candidate does not exist for replacing TCA. Solvent incompatibility with process materials has caused us to seek for niche solvents and/or processing changes that provide an ODC-free solution for special applications. This paper addresses some of the solvent incompatibilities, which have lead to processes changes and possible niche solvent usage. These incompatibilities were discovered during full-scale testing of ODC-free solvents and relate to vulcanized rubber and bond systems in the RSRM. Specifically, the following items are presented: (1) Cure effects of d-limonene based solvents on Silica Filled Ethylene Propylene Diene Monomer (SF-EPDM) rubber. During full-scale test operations, Thiokol discovered that d-limonene (terpene) based solvents inhibit the cure of EPDM rubber. Subsequent testing showed the same issue with Nitrile Butadiene Rubber (NBR). Also discussed are efforts to minimize uncured rubber exposure to solvents; and (2) Cured bond system sensitivity to ODC-free solvents. During full scale testing it was discovered that a natural rubber to steel vulcanized bond could degrade after prolonged exposure to ODC-free solvents. Follow on testing showed that low vapor pressure and residence time seemed to be most likely cause for failure.

Hodgson, James R.↗

An Improved Approach for Analyzing the Oxygen Compatibility of Solvents and other Oxygen-Flammable Materials for Use in Oxygen Systems

Solvents used to clean oxygen system components must be assessed for oxygen compatibility, as incompatible residue or fluid inadvertently left behind within an oxygen system can pose a flammability risk. The most recent approach focused on solvent ignition susceptibility to assess the flammability risk associated with these materials. Previous evaluations included Ambient Pressure Liquid Oxygen (LOX) Mechanical Impact Testing (ASTM G86) and Autogenous Ignition Temperature (AIT) Testing (ASTM G72). The goal in this approach was to identify a solvent material that was not flammable in oxygen. As environmental policies restrict the available options of acceptable solvents, it has proven difficult to identify one that is not flammable in oxygen. A more rigorous oxygen compatibility approach is needed in an effort to select a new solvent for NASA applications. NASA White Sands Test Facility proposed an approach that acknowledges oxygen flammability, yet selects solvent materials based on their relative oxygen compatibility ranking, similar to that described in ASTM G63-99. Solvents are selected based on their ranking with respect to minimal ignition susceptibility, damage and propagation potential, as well as their relative ranking when compared with other solvent materials that are successfully used in oxygen systems. Test methods used in this approach included ASTM G86 (Ambient Pressure LOX Mechanical Impact Testing and Pressurized Gaseous Oxygen (GOX) Mechanical Impact Testing), ASTM G72 (AIT Testing), and ASTM D240 (Heat of Combustion (HOC) Testing). Only four solvents were tested through the full battery of tests for evaluation of oxygen compatibility: AK-225G as a baseline comparison, Solstice PF, L-14780, and Vertrel MCA. Baseline solvent AK-225G exhibited the lowest HOC and highest AIT of solvents tested. Nonetheless, Solstice PF, L-14780, and Vertrel MCA HOCs all fell well within the range of properties that are associated with proven oxygen system materials. Tested AITs for these solvents fell only slightly lower than the AIT for the proven AK-225G solvent. Based on these comparisons in which solvents exhibited properties within those ranges seen with proven oxygen system materials, it is believed that Solstice PF, L-14780, and Vertrel MCA would perform well with respect to oxygen compatibility.

Harper, Susan A.↗

Single Stage Contactor Testing Of The Next Generation Solvent Blend

The Modular Caustic Side Solvent Extraction (CSSX) Unit (MCU) facility at the Savannah River Site (SRS) is actively pursuing the transition from the current BOBCalixC6 based solvent to the Next Generation Solvent (NGS)-MCU solvent to increase the cesium decontamination factor. To support this integration of NGS into the MCU facility the Savannah River National Laboratory (SRNL) performed testing of a blend of the NGS (MaxCalix based solvent) with the current solvent (BOBCalixC6 based solvent) for the removal of cesium (Cs) from the liquid salt waste stream. This testing utilized a blend of BOBCalixC6 based solvent and the NGS with the new extractant, MaxCalix, as well as a new suppressor, tris(3,7dimethyloctyl) guanidine. Single stage tests were conducted using the full size V-05 and V-10 liquid-to-liquid centrifugal contactors installed at SRNL. These tests were designed to determine the mass transfer and hydraulic characteristics with the NGS solvent blended with the projected heel of the BOBCalixC6 based solvent that will exist in MCU at time of transition. The test program evaluated the amount of organic carryover and the droplet size of the organic carryover phases using several analytical methods. The results indicate that hydraulically, the NGS solvent performed hydraulically similar to the current solvent which was expected. For the organic carryover 93% of the solvent is predicted to be recovered from the stripping operation and 96% from the extraction operation. As for the mass transfer, the NGS solvent significantly improved the cesium DF by at least an order of magnitude when extrapolating the One-stage results to actual Seven-stage extraction operation with a stage efficiency of 95%.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Performance of hydrophobic physical solvents for pre-combustion CO 2 capture at a pilot scale coal gasification facility

Here, in this paper, we present the first pilot plant data for hydrophobic physical solvents for CO 2 and H 2 S removal from coal-derived H 2 -rich syngas. Four physical solvents were tested under pre-combustion CO 2 capture conditions at bench scale and pilot plant scale: one baseline hydrophilic solvent and three hydrophobic solvents. The solvents were: (1) polyethylene-glycol-dimethyl ether (PEGDME), a hydrophilic solvent analog for the commercial process Selexol, (2) tributyl- phosphate (TBP), a commercially available hydrophobic solvent, (3) polyethylene glycol-poly(dimethylsiloxane) (PEG-PDMS-3), and (4) diethyl sebacate (CASSH-1), a novel, computationally screened hydrophobic solvent developed by the National Energy Technology Laboratory (NETL). All solvents were studied under pure gas (CO 2 /N 2 /H 2 /CH 4 ) equilibrium conditions at NETL followed by pilot plant testing with syngas at the University of North Dakota Energy & Environmental Research Center (UND EERC). Long term performance of CASSH-1 and PEDGME was then assessed with results compared to process simulation predictions. Within experimental uncertainties, all solvents showed comparable CO 2 absorption performance at above room temperature operation while the hydrophobic solvents had limited water uptake and low vapor pressure, which alleviates concerns related to corrosion, water absorption, and solvent loss to evaporation. These results indicate low viscosity, low vapor pressure hydrophobic solvents are a promising option for lower cost CO 2 capture from high pressure syngas applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Solvent hold tank sample results for MCU-17-150-152 (July 2017) and MCU-17-153-155 (August 2017): Quarterly report

A trend summary that includes the last two Solvent Hold Tank (SHT) monthly samples is shown; MCU- 17-150-152 (July SHT) and MCU-17-153-155 (August SHT). Since the last SHT sample sent for analysis was the August sample the chemical state of the solvent is best approximated by the chemical analysis of the August SHT sample (MCU-17-153-155). This report mainly focused on the chemical analysis of the August SHT sample. The analysis data from the July SHT sample are presented in the “trend” plots of this report. Analysis of the August SHT sample (MCU-17-153-155) indicated that the modifier (CS-7SB) was 2% below but the extractant (MaxCalix) concentration was at its nominal recommended level (169,000 mg/L and 46,400 mg/L respectively). The suppressor (TiDG) level has decreased since the last measurement taken while the Modular Caustic-Side Solvent Extraction unit (MCU) was operating in January 2017, but has remained steady in the range of 666 (observed in April) to 715 mg/L (observed in the August 2017 sample) since February 2017, well above the minimum recommended level (479 mg/L), but below the nominal level. The “flat” trends observed in the TiDG, MaxCalix, modifier, and Gamma measurement are consistent with the solvent being idle since January 10, 2017. A strong correlation between density and modifier concentration in the solvent continues to be observed in the SHT samples. This analysis confirms the Isopar™L addition to the solvent in January 2017. This analysis also indicates the solvent did not require further additions. Based on the current monthly sample, the levels of TiDG, Isopar™L, MaxCalix, and modifier are sufficient for continuing operation but are expected to decrease with time if the Modular Caustic-Side Solvent Extraction Unit (MCU) returns to processing radioactive liquid waste. Otherwise, the levels of these components will remain steady. A future Isopar™L trimming addition to the solvent is recommended when MCU resumes processing waste. Two unknown impurities related to the modifier (but not sec-butyl phenol: a modifier degradation product observed before) at the 290 and 110 mg/L levels were observed in the August SHT sample by the Gas - Chromatography-Mass Spectrometry (GC-MS) method. They were observed in a second GC-MS re-run with a new column. Their identification can’t be ascertained at this time. No impurities were observed in the Hydrogen Nuclear Magnetic Resonance (HNMR). Another impurity observed in the samples was mercury. Based on the August SHT sample, up to 23 ± 5 micrograms of mercury per mL of solvent was detected (the average of the Cold Vapor-Atomic Adsorption [CV-AA] and X-Ray Fluorescence [XRF] methods). The higher mercury concentration in the solvent (as determined in the last three-monthly samples) is possibly due to either a higher mercury concentration in Salt Batches 8 and 9 (Tank 49H) . The gamma level (~ 2.0E4 dpm/mL) measured in the August SHT samples was one order of magnitude lower than the gamma levels observed in the December 2016 and January 2017 SHT samples. A similar level was observed in the July SHT sample (MCU-SHT-150-152). The gamma level has remained consistently steady since January 10, 2017 when MCU stopped processing radioactive liquid waste. The laboratory will continue to monitor the quality of the solvent in particularly for any new impurities or degradation of the solvent components.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Screening green solvents for multilayer plastic film recycling processes

Multilayer (ML) plastic films are essential packaging materials that help protect products from diverse external factors; however, only 5% of all ML films are recycled in the United States. Solvent-based technologies are a promising alternative for recycling ML films because they enable recovery of constituent polymer resins. For example, the Solvent Targeted Recovery and Precipitation (STRAPTM) process sequentially dissolves and separates polymer components using a series of targeted solvent washes. A crucial design aspect of this process is the impact of selected solvents on human health and on the environment. Here, this work introduces a computational framework that integrates molecular modeling, process modeling, techno-economic analysis (TEA), and life-cycle analysis (LCA) to quickly screen green solvents for solvent-based ML recycling processes. Initial screening for solvents based on selectivity is performed by estimating temperature-dependent solubilities using molecular-scale models. Subsequent screening uses basic estimates of energy use and octanol-water partition coefficients (logP) as key measures of health, safety, and environmental hazards. Detailed process modeling, TEA, and LCA are used on a reduced set of promising solvents identified in early screening steps to more accurately determine how solvent selection and associated operating conditions impact overall economics and environmental impacts. The framework is used for the identification of green solvents (from a database of 1,000 solvents) that separate an industrial ML film composed of polyethylene (PE), ethylene vinyl alcohol (EVOH), and polyethylene terephthalate (PET). Our analysis shows the effectiveness of the framework and reveals fundamental trade-offs between solvent greenness, solubility, and economics. Our work emphasizes the importance of taking a holistic systems view during solvent design and aims to inform the development of new processes for ML film recycling and the identification of new ML films that are easier to recycle.

economics↗

High Performance Solvent for NGCC Flue Gas CO 2 Capture (Final Technical Report)

Amine-based solvent absorption is the most mature and reliable technology for large scale CO 2 capture, dating back to the 1930s when monoethanolamine (MEA) was used to treat acid gases from oil refineries. However, while strategic advancements have optimized the CO2 capture process, the cost of capture remains high, where current estimates suggest that CO 2 capture costs are around $\$$72/tonne of CO 2 . To address this, solvent development and optimization have become a focus of current research. This project sought to develop a high-performance solvent to reduce the overall cost of CO 2 capture from NGCC flue gas. Here, solvent optimization focused on: (1) reducing the energy required for CO 2 desorption in a reboiler, (2) improving CO 2 absorption and desorption reaction kinetics, (3) improving solvent stability, and (4) reducing environmental impacts. Susteon has developed and evaluated a promoted solvent, Sustenol™, for NGCC flue gas CO 2 capture. The optimized Sustenol™ also shows a higher dynamic CO 2 absorption capacity of ~0.5 mol CO2 /mol amine compared to 0.25 mol CO2 /mol amine for 30 wt% MEA. Additionally, the solvent is oxidatively, thermally and hydrothermally stable, which leads to lower solvent loss and emissions. These advancements have resulted in a solvent regeneration energy of 2.16 GJ/tonne of CO 2 which is >30% lower than current state-of-the-art commercial and emerging solvents. Combined with empirical data from the bench and pilot scale testing, this preliminary TEA study indicated the cost of CO 2 capture by Sustenol™ for 97% CO 2 removal at $\$$54/tonne and for 90% removal at $\$$49/tonne, with a pathway to achieve $\$$45/tonne of CO 2 with continued process and solvent advancements. Susteon has developed a technology roadmap to reduce the cost of CO 2 capture to <$\$$45/tonne for NGCC flue gas. Susteon plans to derisk this technology for commercial deployment through comprehensive solvent degradation testing, long-term testing in a pilot plant at 5 tonne CO2 /day and demonstration scale testing at 100 tonne CO2 /day with NGCC flue gas and engineering design studies to qualify Sustenol™ as a drop-in replacement solvent.

03 NATURAL GAS↗

From Bulk to Interface: Solvent Exchange Dynamics and Their Role in Ion Transport and the Interfacial Model of Rechargeable Magnesium Batteries

Multivalent battery chemistries have been explored in response to the increasing demand for high-energy rechargeable batteries utilizing sustainable resources. Solvation structures of working cations have been recognized as a key component in the design of electrolytes; however, most structure–property correlations of metal ions in organic electrolytes usually build upon favorable static solvation structures, often overlooking solvent exchange dynamics. We here report the ion solvation structures and solvent exchange rates of magnesium electrolytes in various solvents by using multimodal nuclear magnetic resonance (NMR) analysis and molecular dynamics/density functional theory (MD/DFT) calculations. These magnesium solvation structures and solvent exchange dynamics are correlated to the combined effects of several physicochemical properties of the solvents. Moreover, Mg 2+ transport and interfacial charge transfer efficiency are found to be closely correlated to the solvent exchange rate in the binary electrolytes where the solvent exchange is tunable by the fraction of diluent solvents. Our primary findings are (1) most battery-related solvents undergo ultraslow solvent exchange coordinating to Mg 2+ (with time scales ranging from 0.5 μs to 5 ms), (2) the cation transport mechanism is a mixture of vehicular and structural diffusion even at the ultraslow exchange limit (with faster solvent exchange leading to faster cation transport), and (3) an interfacial model wherein organic-rich regions facilitate desolvation and inorganic regions promote Mg 2+ transport is consistent with our NMR, electrochemistry, and cryogenic X-ray photoelectron spectroscopy (cryo-XPS) results. In conclusion, this observed ultraslow solvent exchange and its importance for ion transport and interfacial properties necessitate the judicious selection of solvents and informed design of electrolyte blends for multivalent electrolytes.

25 ENERGY STORAGE↗

What do far-infrared spectra of solitary water in “water-in-solvent” systems reveal about water’s solvation and dynamics?

Classical molecular dynamics simulations of water in ionic and dipolar solvents were used to interpret the far-infrared (FIR) rotation/libration spectra of “solitary water” in terms of water’s rotational dynamics and interactions with solvents. Seven solvents represented by nonpolarizable all-atom force fields and a series of idealized variable-charge solvents were used to span the range of solvent polarities (hydrogen bonding) studied experimentally. Simulated spectra capture the solvent dependence observed, as well as the relationship between the frequencies of water libration (νL) and OH stretching bands (νOH). In more strongly interacting solvents, simulated νL are ∼20% higher than those of experiment. In all solvents, the simulated spectra are composites of rotational motions about the two axes perpendicular to water’s dipole moment, and the different frequencies of these two motions are responsible for the breadth of the libration band and the bimodal shape observed in halide ionic liquids. Simulations overestimate the separation of these two components in most solvents. The character of water rotational motions changes markedly with solvent polarity, from quasi-free rotation in nonpolar and weakly polar solvents to highly constrained libration in strongly hydrogen bonding environments. The changeover to librational motions dominating the spectrum occurs between solvents such as benzene (νL ∼ 250 cm−1) and acetonitrile (νL ∼ 400 cm−1). For solvents in the latter category, the mean frequency of the experimental FIR band provides a direct measure of mean-squared torques and, therefore, force constants associated with interactions constraining water’s librational motion.

Chemistry↗

Next Generation Solvent Vapor Pressure Testing

Previous work by Savannah River National Laboratory (SRNL) indicated that the actual Next Generation Solvent vapor pressure would be higher than the Original Caustic Side Solvent Extraction (CSSX) solvent vapor pressure, but below a bounding vapor pressure using Raoult’s Law. Since solvent vapor pressure has a significant impact on Composite Lower Flammability Limits (CLFL) and attendant accident analyses, obtaining an additional margin from the bounding NGS vapor pressure would be valuable. In order to quantify how much margin might be gained from the NGS bounding solvent, SRNL researchers were requested to perform vapor pressure testing with the Next Generation Solvent (NGS) by Savannah River Mission Completion (SRMC). The vapor pressure curve for the NGS formulation set to be deployed at the Salt Waste Processing Facility (SWPF) has been determined by SRNL up to 55°C (131°F) using headspace Gas Chromatography (GC). It was expected that NGS would have a higher vapor pressure than the Original CSSX solvent; however, experimental results indicate a lower vapor pressure. At this time, it is uncertain if this difference is due to the 7x increase in concentration of the large calixarene in the solvent (0.007M BOBCalix in Original CSSX solvent vs. 0.05M MaxCalix in NGS) or to minor batch-to-batch variations in Isopar-L constituents. The NGS and the Original CSSX solvent vapor pressure data were fitted to the Antoine Equation. The Antoine equation gives a more accurate representation of the expected vapor pressure of the solvents outside of the temperature range tested. The Antoine equation fitting for NGS is given below: $P=10^{6.364⁻\frac{1788.4}{T+219.3}}$. Where, p is the vapor pressure (partial pressure) of NGS in mmHg and T is the temperature in °C. It is recommended that SRMC either continue using the more conservative Isopar-L vapor pressure calculations at SWPF with the equation developed for the Original CSSX solvent, or the equation presented above for the NGS solvent. Additionally, it is recommended to study the variability in Isopar-L vapor pressure between lots.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Effects of Solvent Composition on the Assembly and Relaxation of Triblock Copolymer-Based Polyelectrolyte Gels

The role of solvent selectivity has been explored extensively with regard to its role in the phase behavior of block copolymer assemblies. Traditionally, thermally induced phase separation is employed for generating micelles upon cooling a block copolymer dissolved in a selective solvent. However few amphiphilic, polyelectrolyte-containing block copolymers demonstrate a thermally accessible route of micellization, and solvent exchange routes are frequently employed instead. Here, we describe the use of mixed solvents for obtaining thermoreversible gelation behavior of poly(methyl methacrylate)-poly(methacrylic acid)-poly(methyl methacrylate) (PMMA-PMAA-PMMA) triblock copolymers. One solvent component (dimethyl sulfoxide) is a good solvent for both blocks, and the second solvent component (water) is a selective solvent for the polymer midblock. Rheological frequency sweeps at variable solvent compositions and temperatures demonstrate an adherence to time-temperature-composition superposition, so that changes in the solvent composition are analogous to changes in the Flory-Huggins interaction parameter between end block and solvent. Shift factors used for this superposition are related to the effective activation energy describing the viscosity and stress relaxation response of the triblock copolymer gels. The effectiveness of solvent exchange processes for producing hydrogels with this system is shown to originate from the ability of a small amount of added water to greatly increase the relaxation times of the self-assembled polymer gels that are formed by this process.

36 MATERIALS SCIENCE↗

RESULTS OF CESIUM MASS TRANSFER TESTING FOR NEXT GENERATION SOLVENT WITH HANFORD WASTE SIMULANT AP-101

SRNL has performed an Extraction, Scrub, Strip (ESS) test using the next generation solvent and AP-101 Hanford Waste simulant. The results indicate that the next generation solvent (MG solvent) has adequate extraction behavior even in the face of a massive excess of potassium. The stripping results indicate poorer behavior, but this may be due to inadequate method detection limits. SRNL recommends further testing using hot tank waste or spiked simulant to provide for better detection limits. Furthermore, strong consideration should be given to performing an actual waste, or spiked waste demonstration using the 2cm contactor bank. The Savannah River Site currently utilizes a solvent extraction technology to selectively remove cesium from tank waste at the Multi-Component Solvent Extraction unit (MCU). This solvent consists of four components: the extractant - BoBCalixC6, a modifier - Cs-7B, a suppressor - trioctylamine, and a diluent, Isopar L{trademark}. This solvent has been used to successfully decontaminate over 2 million gallons of tank waste. However, recent work at Oak Ridge National Laboratory (ORNL), Argonne National Laboratory (ANL), and Savannah River National Laboratory (SRNL) has provided a basis to implement an improved solvent blend. This new solvent blend - referred to as Next Generation Solvent (NGS) - is similar to the current solvent, and also contains four components: the extractant - MAXCalix, a modifier - Cs-7B, a suppressor - LIX-79{trademark} guanidine, and a diluent, Isopar L{trademark}. Testing to date has shown that this 'Next Generation' solvent promises to provide far superior cesium removal efficiencies, and furthermore, is theorized to perform adequately even in waste with high potassium concentrations such that it could be used for processing Hanford wastes. SRNL has performed a cesium mass transfer test in to confirm this behavior, using a simulant designed to simulate Hanford AP-101 waste.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

The solvent component of macromolecular crystals

On average, the mother liquor or solvent and its constituents occupy about 50% of a macromolecular crystal. Ordered as well as disordered solvent components need to be accurately accounted for in modelling and refinement, often with considerable complexity. The mother liquor from which a biomolecular crystal is grown will contain water, buffer molecules, native ligands and cofactors, crystallization precipitants and additives, various metal ions, and often small-molecule ligands or inhibitors. On average, about half the volume of a biomolecular crystal consists of this mother liquor, whose components form the disordered bulk solvent. Its scattering contributions can be exploited in initial phasing and must be included in crystal structure refinement as a bulk-solvent model. Concomitantly, distinct electron density originating from ordered solvent components must be correctly identified and represented as part of the atomic crystal structure model. Herein, are reviewed (i) probabilistic bulk-solvent content estimates, (ii) the use of bulk-solvent density modification in phase improvement, (iii) bulk-solvent models and refinement of bulk-solvent contributions and (iv) modelling and validation of ordered solvent constituents. A brief summary is provided of current tools for bulk-solvent analysis and refinement, as well as of modelling, refinement and analysis of ordered solvent components, including small-molecule ligands.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗