Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SOLAR CELLS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Codesigning Alloy Compositions of CdSe y Te 1− y Absorbers and Mg x Zn 1− x O Contacts to Increase Solar Cell Efficiency

Thin‐film solar cells such as CdTe are a major commercial photovoltaic technology, with more than 25 GW installed worldwide and levelized costs of electricity competitive with fossil fuels. Further progress may result from integrating CdSe y Te 1− y absorbers with Mg x Zn 1− x O contacts, but the device efficiency is difficult to maximize due to coupled dependence on chemical composition of both alloys. Herein, a high‐throughput approach is demonstrated to codesign chemical compositions in alloyed Mg x Zn 1− x O/CdSe y Te 1− y thin‐film solar cells, using combinatorial libraries of PV devices with orthogonal composition gradients in CdSe y Te 1− y absorbers and Mg x Zn 1− x O contacts. It is found that the solar cell performance is a strong and coupled function of both elemental compositions, with efficiency up to 17.7% ( V OC = 836 mV, fill factor = 69%, J SC = 30.6 mA cm −2 ) at atomic compositions of Mg/(Mg + Zn) ≈18% and average Se/(Se + Te) ≈4%. These performance trends among >100 devices are explained by >100 ns lifetime of photoexcited charge carriers at the Mg x Zn 1− x O/CdSe y Te 1− y interface where strong Se accumulation is also observed. This study reports the optimal compositions of the commercially relevant Mg x Zn 1− x O/CdSe y Te 1− y solar cells and demonstrates a general approach to codesigning performance of alloyed thin‐film solar cells and other optoelectronic devices.

14 SOLAR ENERGY↗
NASA NTRS2012

Solar Cell and Array Technology Development for NASA Solar Electric Propulsion Missions

NASA is currently developing advanced solar cell and solar array technologies to support future exploration activities. These advanced photovoltaic technology development efforts are needed to enable very large (multi-hundred kilowatt) power systems that must be compatible with solar electric propulsion (SEP) missions. The technology being developed must address a wide variety of requirements and cover the necessary advances in solar cell, blanket integration, and large solar array structures that are needed for this class of missions. Th is paper will summarize NASA's plans for high power SEP missions, initi al mission studies and power system requirements, plans for advanced photovoltaic technology development, and the status of specific cell and array technology development and testing that have already been conducted.

Piszczor, Michael↗
DOE OSTI2019

Semitransparent Sb 2 S 3 thin film solar cells by ultrasonic spray pyrolysis for use in solar windows

The integration of photovoltaic (PV) solar energy in zero-energy buildings requires durable and efficient solar windows composed of lightweight and semitransparent thin film solar cells. Inorganic materials with a high optical absorption coefficient, such as Sb 2 S 3 (>10 5 cm -1 at 450 nm), offer semitransparency, appreciable efficiency, and long-term durability at low cost. Oxide-free throughout the Sb 2 S 3 layer thickness, as confirmed by combined studies of energy dispersive X-ray spectroscopy and synchrotron soft X-ray emission spectroscopy, semitransparent Sb 2 S 3 thin films can be rapidly grown in air by the area-scalable ultrasonic spray pyrolysis method. Integrated into a ITO/TiO 2 /Sb 2 S 3 /P3HT/Au solar cell, a power conversion efficiency (PCE) of 5.5% at air mass 1.5 global (AM1.5G) is achieved, which is a record among spray-deposited Sb 2 S 3 solar cells. An average visible transparency (AVT) of 26% of the back-contact-less ITO/TiO 2 /Sb 2 S 3 solar cell stack in the wavelength range of 380–740 nm is attained by tuning the Sb 2 S 3 absorber thickness to 100 nm. In scale-up from mm 2 to cm 2 areas, the Sb 2 S 3 hybrid solar cells show a decrease in efficiency of only 3.2% for an 88 mm 2 Sb 2 S 3 solar cell, which retains 70% relative efficiency after one year of non-encapsulated storage. A cell with a PCE of 3.9% at 1 sun shows a PCE of 7.4% at 0.1 sun, attesting to the applicability of these solar cells for light harvesting under cloud cover.

36 MATERIALS SCIENCE↗
NASA NTRS1993

Diffusion length variation and proton damage coefficients for InP/In(x)Ga(1-x)As/GaAs solar cells

Indium phosphide solar cells are more radiation resistant than gallium arsenide and silicon solar cells, and their growth by heteroepitaxy offers additional advantages leading to the development of lighter, mechanically strong and cost-effective cells. Changes in heteroepitaxial InP cell efficiency under 0.5 and 3 MeV proton irradiations are explained by the variation in the minority-carrier diffusion length. The base diffusion length versus proton fluence is calculated by simulating the cell performance. The diffusion length damage coefficient K(L) is plotted as a function of proton fluence.

Jain, R. K.↗
NASA NTRS1988

Improvements in InP solar cells

Indium phosphide solar cells with very thin n-type emitters have been made by both ion implantation and metal-organic chemical vapor deposition. Air mass zero efficiencies as high as 18.8 percent (NASA measurement) have been achieved. The best cells, which were those made by ion implantation, show an open-circuit voltage of 873 mV, short-circuit current of 35.7 mA/sq cm, and fill factor of 0.829. Improvements are anticipated in all three of these parameters. Internal quantum efficiency peaks at over 90 percent in the red end of the spectrum, but drops to 54 percent in the blue end. Other cells have achieved 74 percent in the blue end. A preliminary investigation of InP solar cells on foreign substrates has been carried out. Although problems have been encountered with doping of the InP by the substrate, cells of 7.1 percent efficiency on silicon and cells of 9.4 percent, efficiency on GaAs have been made.

Keavney, Christopher↗
NASA NTRS1978

Universal test fixture for solar cells

Coverings for solar cells are evaluated conveniently with alumina ceramic circuit board holding three pairs of cells and three field-effect translator (FET) chips overlaid with candidate encapsulant. With fixture, solar cells and encapsulants are exposed to Sunlight and weather, either natural or artificial, to provide pertinent measurement and performance data.

Kolyer, J. M.↗
NASA NTRS1986

Flat-plate solar array project. Volume 4: High-efficiency solar cells

The High Efficiency Solar Cell Task was assigned the objective of understanding and developing high efficiency solar cell devices that would meet the cost and performance goals of the Flat Plate Solar Array (FSA) Project. The need for research dealing with high efficiency devices was considered important because of the role efficiency plays in reducing price per watt of generated energy. The R&D efforts conducted during the 1982 to 1986 period are summarized to provide understanding and control of energy conversion losses associated with crystalline silicon solar cells. New levels of conversion efficiency were demonstrated. Major contributions were made both to the understanding and reduction of bulk and surface losses in solar cells. For example, oxides, nitrides, and polysilicon were all shown to be potentially useful surface passivants. Improvements in measurement techniques were made and Auger coefficients and spectral absorption data were obtained for unique types of silicon sheets. New modelling software was developed including a program to optimize a device design based on input characteristics of a cell.

Leipold, M.↗
NASA NTRS1971

Silicon solar cells as a high-solar-intensity radiometer

The characteristics of a conventional, 1- by 2-cm, N/P, gridded silicon solar cell when used as a radiometer have been determined for solar intensity levels to 2800 mW/sq cm (20 solar constants). The short-circuit current was proportional to the radiant intensity for levels only to 700 mW/sq cm (5 solar constants). For intensity levels greater than 700 mW/sq cm, it was necessary to operate the cell in a photoconductive mode in order to obtain a linear relation between the measured current and the radiant intensity. When the solar cell was biased with a reverse voltage of -1 V, the measured current and radiant intensity were linearly related over the complete intensity range from 100 to 2800 mW/sq cm.

Spisz, E. W.↗
NASA NTRS1972

Development of GaAs solar cells

Calculations of GaAs solar cell output parameters were refined and a computer model was developed for parameter optimization. The results were analyzed to determine the material characteristics required for a high efficiency solar cell. Calculated efficiencies for a P/N cell polarity are higher than an N/P cell. Both cell polarities show efficiency to have a larger dependence on short circuit current than an open circuit voltage under nearly all conditions considered. The tolerances and requirements of a cell fabrication process are more critical for an N/P type than for a P/N type cell. Several solar cell fabrication considerations relative to junction formation using ion implantation are also discussed.

Mcnally, P. J.↗
NASA NTRS1993

Generating AC With Rotating Solar Cells

Rotating solar photovoltaic cells or batteries connected to suitable mechanical and/or electronic commutators produce nearly sinusoidal alternating current. Eliminates need for inverter circuitry and its attendant power-consumption and heat-dissipation problems, but imposes need for low-power-consumption rotary mechanism. Intended for use aboard spacecraft, also useful in special terrestrial situations where solar electric power must be transmitted over powerlines from one remote location to another.

Flanagan, David T.↗
NASA NTRS1981

Effects of low temperature periodic annealing on the deep-level defects in 200 keV proton irradiated AlGaAs-GaAs solar cells

The GaAs solar cell has shown good potential for space applications. However, degradation in performance occurred when the cells were irradiated by high energy electrons and protons in the space environment. The considered investigation is concerned with the effect of periodic thermal annealing on the deep-level defects induced by the 200 keV protons in the AlGaAs-GaAs solar cells. Protons at a fluence of 10 to the 11th P/sq cm were used in the irradiation cycle, while annealing temperatures of 200 C (for 24 hours), 300 C (six hours), and 400 C (six hours) were employed. The most likely candidate for the E(c) -0.71 eV electron trap observed in the 200 keV proton irradiated samples may be due to GaAs antisite, while the observed E(v) +0.18 eV hole trap has been attributed to the gallium vacancy related defect. The obtained results show that periodic annealing in the considered case does not offer any advantages over the one time annealing process.

Li, S. S.↗
NASA NTRS1987

Results of 1 MeV proton irradiation of front and back surfaces of silicon solar cells

Several silicon solar cells with and without back surface fields (BSF), having thicknesses of 200 microns and 63 microns were irradiated with 1 MeV protons having fluences between 1 times 10 to the 10th power and 1 times 10 to the 12th power p/square cm. The irradiation was performed using both normal and isotropic incidence on the front as well as back surfaces of the solar cells. The results of the back surface irradiations are analyzed using a model in which irradiation induced defects across the high-low (BSF) junction are considered. It is concluded that degradation of the high-low junction is responsible for the severe performance loss in thinner cells when irradiated from the rear.

Anspaugh, B. E.↗
DOE OSTI2023

Synthesizing and formulating metal oxide nanoparticle inks for perovskite solar cells

The perovskite solar cell has commercial potential due to the low-cost of materials and manufacturing processes with cell efficiencies on par with traditional technologies. Nanomaterials have many properties that make them attractive for the perovskite devices, including low-cost inks, low temperature processing, stable material properties and good charge transport. In this feature article, the use of nanomaterials in the hole transport and electron transport layers are reviewed. Specifically, SnO 2 and NiO x are the leading materials with the most promise for translation to large scale applications. Here, the review includes a discussion of the synthesis, formulation, and processing of these nanoparticles and provides insights for their further deployment towards commercially viable perovskite solar cells.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1980

Effects of grain boundaries in polycrystalline solar cells

In polycrystalline solar cells, the short-circuit current is reduced (compared to single-crystal cells) due to recombination of minority carriers at the grain boundaries. The magnitude of this reduction is calculated for the case of a monochromatic beam of light, assuming that both the light beam and the grain boundaries are perpendicular to a p-n junction. The photoresponse of the junction is calculated in terms of the absorption coefficient of the light, the minority-carrier diffusion length, the surface recombination velocity at the grain boundary and the distance of the light beam from the grain boundary. The analysis gives an expression for an effective grain boundary width which depends on wavelength. This width determines the reduction in short-circuit current of solar cells made from material with columnar-type grains.

Zook, J. D.↗
NASA NTRS1991

Effect of InAlAs window layer on the efficiency of indium phosphide solar cells

Indium phosphide (InP) solar cell efficiencies are limited by surface recombination. The effect of a wide-bandgap lattice-matched indium aluminum arsenide (In0.52Al0.48As) window layer on the performance of InP solar cells was investigated using a numerical code PC-1D. The p(+)n InP solar cell performance improves significantly with the use of a window layer. No improvement is seen for n(+)p InP cells. Cell results are explained by the band diagram of the heterostructure and the conduction-band energy discontinuity. The calculated I-V and internal quantum efficiency results clearly demonstrate that In0.52Al0.48As is a promising candidate as a window layer material for p(+)n InP solar cells.

Jain, R. K.↗
DOE OSTI2020

Thermodynamic Properties and Molecular Packing Explain Performance and Processing Procedures of Three D18:NFA Organic Solar Cells

Abstract Organic solar cells (OSCs) based on D18:Y6 have recently exhibited a record power conversion efficiency of over 18%. The initial work is extended and the device performance of D18‐based OSCs is compared with three non‐fullerene acceptors, Y6, IT‐4F, and IEICO‐4Cl, and their molecular packing characteristics and miscibility are studied. The D18 polymer shows unusually strong chain extension and excellent backbone ordering in all films, which likely contributes to the excellent hole‐transporting properties. Thermodynamic characterization indicates a room‐temperature miscibility for D18:Y6 and D18:IT‐4F near the percolation threshold. This corresponds to an ideal quench depth and explains the use of solvent vapor annealing rather than thermal annealing. In contrast, D18:IEICO‐4Cl is a low‐miscibility system with a deep quench depth during casting and poor morphology control and low performance. A failure of ternary blends with PC 71 BM is likely due to the near‐ideal miscibility of Y6 to begin with and indicates that strategies for developing successful ternary or quaternary solar cells are likely very different for D18 than for other high‐performing donors. This work reveals several unique property–performance relations of D18‐based photovoltaic devices and helps guide design or fabrication of yet higher efficiency OSCs.

Wang, Zhen↗