Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SHIPS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Examination of shipping packages 9975-01658, 9975-02075 and 9975-02738

SRNL has assisted in the examination of three 9975 shipping packages (9975-01658, 9975-02075 and 9975-02738) following their use for storage of nuclear material in K-Area Complex (KAC). Each of these was targeted for examination because the axial gap exceeded the 1 inch maximum criterion, signaling the potential for degradation of the fiberboard overpack and drum. Each package experienced a degree of compaction of the bottom fiberboard layers, and had elevated moisture levels toward the bottom. A small amount of mold was observed on the lower fiberboard assembly in 9975-02738. However, the majority of the fiberboard in each package appeared to retain good integrity consistent with non-degraded material. Minor corrosion was observed on these drums, but is judged to have not compromised the drum integrity.

42 ENGINEERING↗

Examination of Shipping Packages 9975-02694 and 9975-02729

SRNL has assisted in the examination of two 9975 shipping packages (9975-02694 and 9975-02729) following their use for storage of nuclear material in K-Area Complex (KAC). Both of these were targeted for examination because they were exposed to water from a leaking expansion joint during storage. When first opened in KAC, the axial gap was found to be in excess of the 1 inch maximum criterion, signaling the potential for degradation of the fiberboard overpack and drum. Within each package the highest fiberboard moisture levels were observed in the bottom layers, but no mold was observed in either package. The fiberboard in each package appeared to retain good integrity consistent with non-degraded material. Minor corrosion was also observed on these drums along the lower stitch welds and on several closure bolts.

42 ENGINEERING↗

9975 Shipping package component long-term degradation rates

Special nuclear materials are being stored in the K-Area Complex using 3013 containers that are held within Model 9975 shipping packages. The service life for these packages in storage was recently increased from 15 to 20 years, since some of these packages have been stored for nearly 15 years. A strategy is also being developed whereby such storage might be extended beyond 20 years. This strategy is based on recent calculations that support acceptable 9975 package performance for 20 years with internal heat loads up to 19 watts, and identifies a lower heat load limit for which the package components should degrade at half the bounding rate or less, thus doubling the effective storage life for these lower wattage packages. The components of the 9975 package that are sensitive to aging under storage conditions are the fiberboard overpack and the O-ring seals, although some degradation of the lead shield and outer drum are also possible. This report summarizes degradation rates applicable to lower heat load storage conditions. In particular, the O-ring seals should provide leak-tight performance for more than 40 years in packages for which their maximum temperature is ≤135 °F. Similarly, the fiberboard should remain acceptable in performance of its required safety functions for up to 40 years in packages with a maximum fiberboard temperature ≤125 °F.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Preparing and Shipping Waste/Material Off-Site

This Technical Procedure provides instructions for shipping waste/materials originating from and owned by the U.S. Department of Energy (DOE) Los Alamos National Laboratory to commercial or federally owned, operated, or licensed waste treatment, storage, and disposal facilities (TSDFs). Federal facilities include those owned/operated and/or licensed by the DOE and the Nuclear Regulatory Commission (NRC).

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Preparation & shipping of ten neutron irradiated Eurofer97 steel variants to HFIR for SANS experiments

At ORNL, ten variants of Eurofer97 steel were irradiated in the high flux isotope reactor (HFIR) to ~2.94 – 3.24 dpa at 300 ± 30 °C, as part of the EUROfusion Lot-IV collaboration. The irradiations were performed in non-instrumented rabbit capsules in the flux trap region, which included SS-J3 type tensile samples and M4-CVN multi-notch bend bars. Their full set of microstructure and mechanical properties were previously reported in multiple previous publications. In this project, half-broken irradiated and nonirradiated SS-J3 tensile samples from ten alloys, code-named H, I, J, K, L, M, N, O, P and E, were prepared and shipped for facilitating small angle neutron scattering (SANS) experiments at the HFIR general purpose (GP)-SANS beam line. This report summarizes the completed tasks which included canister moves at the Irradiated Materials Examination and Testing (IMET) hot-cell facility to retrieve the samples from long-term storage, loading of the ten irradiated samples at IMET inside lead (Pb) piglets that were specifically provided by ORNL for SANS experiments and radiological shipment from IMET facility to the HFIR hot cells for performing SANS experiments. In addition to the irradiated samples, ten nonirradiated half-broken pieces from the Eurofer97 variants were also provided to HFIR for SANS.

36 MATERIALS SCIENCE↗

Technical Review Report for the Application for Contents Amendment for Shipping Isentropic Compression Experiment (ICE) Apparatus in 9977 Packaging

This report documents the review of Application for Contents Amendment for Shipping Isentropic Compression Experiment (ICE) Apparatus in 9977 Packaging, prepared by Savannah River Packaging Technology (SRPT) of Savannah River National Laboratory (SRNL) of Savannah River Nuclear Solutions, LLC, -- the Submittal -- at the request of the Department of Energy's (DOE) National Nuclear Security Agency's (NNSA) Albuquerque Facility Operations Division, for the shipment of the ICE apparatus from Los Alamos National Laboratory (LANL), to Sandia National Laboratory (SNL). The ICE apparatus consists of a stainless steel assembly containing about 8 grams of {sup 239}Pu or its dose equivalent as noted in Table 1, Comparison of 9977 Content C.1 and the ICE Radioactive Contents, of the Submittal. The ICE target is mounted on the transport container assembly base. A Viton{sup R} O-ring seals the transport container base to the transport container body. Another Viton{sup R} O-ring seals the transport container handle to the transport container body. The ICE apparatus weighs less than 30 pounds and has less than 0.6 watts decay heat rate. For the Model 9977 Package, the maximum payload weight is 100 pounds and the maximum decay heat rate is 19 watts. Thus, the maximum payload weight and the maximum decay heat rate for the Model 9977 Package easily bound those for the ICE apparatus. This Addendum supplements the Safety Analysis Report for Packaging (SARP), Revision 2, for the Model 9977 Package and Addendum 1, Revision 2, to Revision 2 of the Model 9977 Package SARP. The ICE apparatus is considered as part of Content Envelope C.6, Samples and Sources, under the submittal for the Model 9978 Package SARP currently under review. The Staff at Lawrence Livermore National Laboratory (LLNL) recommends that the Submittal be approved by the DOE-Headquarters Certifying Official (EM-60), and incorporated into a subsequent revision to the current Certificate of Compliance (CoC), to the Model 9977-96 Packaging.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

EXAMINATION OF SHIPPING PACKAGES 9975-01818, 9975-01903 AND 9975-02287

Three 9975 shipping packages were examined to investigate the non-conforming condition of an axial air gap greater than 1 inch. This condition typically indicates the presence of excess moisture in the fiberboard overpack, and may be accompanied by degradation in the fiberboard properties. The package with the largest axial air gap (9975-01818, with an air gap of 1.437 inches) was found to contain significant excess moisture, and the lower fiberboard assembly was covered with mold and was significantly degraded in strength. This condition is very similar to that observed previously in package 9975-01819. Both packages (-1818 and -1819) appear to contain a similar amount of excess moisture, which was previously estimated for 9975-01819 as {approx}2.5 liters. The condition of 9975-01818 was also evidenced by several rust spots along the bottom chime of the drum, although no significant rust was noted on the closure bolts. Packages 9975-01903 and 9975-02287 were also examined. The axial air gap in these two packages was less than in 9975-01818, but still exceeded 1 inch. These two packages contained elevated moisture levels, although not significantly higher than seen in other 'typical' packages. The fiberboard in these two packages was of sound integrity, and appeared generally consistent with undegraded material. A few small patches of mold on and near the bottom of the fiberboard in 9975-01903 appeared dormant. No mold was observed on package 9975-02287. The SPA will provide recommendations on possible follow-up activities with these three packages. This might include a demonstration in SRNL of whether removal of the caplugs from similar packages would facilitate removal of excess moisture. Future efforts should also include an assessment of using the 1 inch axial gap criterion as a valid indicator of fiberboard degradation.

42 ENGINEERING↗

EXAMINATION OF SHIPPING PACKAGES 9975-01968, 9975-04353 AND 9975-06870

Three 9975 shipping packages were examined to investigate the non-conforming condition of an axial air gap greater than 1 inch. This condition typically indicates the presence of excess moisture in the fiberboard overpack, and may be accompanied by degradation in the fiberboard properties. In the case of these three packages, no excess moisture was present, and the fiberboard was not visibly degraded. However, the lower fiberboard assembly from 9975-06870 was separated into two pieces. The lead shield from 9975-04353 was heavily corroded, while the shield from 9975-01968 had very little corrosion. In the case of 9975-06870, the shield was covered by a stainless steel sleeve, and the condition of the lead was not observed. No other conditions of concern were observed in these three packages.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

EXAMINATION OF SHIPPING PACKAGE 9975-2130

Shipping package 9975-02130 was examined in K-Area following the identification of a nonconforming condition; the axial gap between the drum flange and upper fiberboard assembly exceeded the maximum allowed value of 1 inch. The average measured axial gap was 1.1 inches. The fiberboard assembly in this package contained moisture levels of {approx}14-24% wood moisture equivalent ({approx}12-19 wt%) This is moderately higher than typically seen in conforming packages, but not as high as seen on most packages which have exceeded the allowed axial gap. Small patches of mold were growing on portions of the lower fiber assembly, but the fiberboard appeared intact and with little apparent change in its integrity. The lead shield had a heavy layer of corrosion product, some of which flaked off easily. The thickness of several flakes was measured, and varied from 0.0016 to 0.0031 inch. However, additional corrosion product remained on the shield under the flaked regions, so the total thickness of corrosion product exceeds 0.0031 inch.

09 BIOMASS FUELS↗

WFIP3 - SHIP site - NREL Scanning Lidar (StreamLine XR+ #235) / Raw data

These data include raw scanning Doppler lidar measurements from the deployment of the NREL Halo XR+ (s/n 235) at WFIP3's SHIP. The raw measurements include uncalibrated beam azimuth angles, radial velocity, backscatter, signal to noise ratio per each line of sight, and range-gate.

17 WIND ENERGY↗

WFIP3 - NOAA SHIP site - NREL Ceilometer (Vaisala CL51) / Derived Data

NOAA SHIP ceilometer: netCDF L3 data files have level 3 (L3) data that have gone through the calculation service and contain all the data from the algorithms, including mixing layer height values, and quality index data. L3 default files contain L3 data that use the default preset for a live plot. File naming schema: L3_DEFAULT_ _YYYYMMDDHHMM_ _ .nc Name Description: L3 Identification of the data level DEFAULT Identification of the L3 file type CUSTOM OFFLINE STATION_NUMBER WMO station number, if defined YYYYMMDDHHMM UTC time ParameterKey Identification of the advanced algorithm settings. See the table below for an explanation. FREE_FORMAT File suffix, if defined

17 WIND ENERGY↗