Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SHEAR PROPERTIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Diffusion bonding of 410 stainless steel to copper using a nickel interlayer

In the present work, plates of stainless steel (grade 410) were joined to copper ones through a diffusion bonding process using a nickel interlayer at a temperature range of 800-950 deg. C. The bonding was performed through pressing the specimens under a 12-MPa compression load and a vacuum of 10{sup -4} torr for 60 min. The results indicated the formation of distinct diffusion zones at both Cu/Ni and Ni/SS interfaces during the diffusion bonding process. The thickness of the reaction layer in both interfaces was increased by raising the processing temperature. The phase constitutions and their related microstructure at the Cu/Ni and Ni/SS diffusion bonding interfaces were studied using optical microscopy, scanning electron microscopy, X-ray diffraction and elemental analyses through energy dispersive spectrometry. The resulted penetration profiles were examined using a calibrated electron probe micro-analyzer. The diffusion transition regions near the Cu/Ni and Ni/SS interfaces consist of a complete solid solution zone and of various phases based on (Fe, Ni), (Fe, Cr, Ni) and (Fe, Cr) chemical systems, respectively. The diffusion-bonded joint processed at 900 deg. C showed the maximum shear strength of about 145 MPa. The maximum hardness was obtained at the SS-Ni interface with a value of about 432 HV.

36 MATERIALS SCIENCE↗

Joining aluminum to titanium alloy by friction stir lap welding with cutting pin

Aluminum 1060 and titanium alloy Ti-6Al-4V plates were lap joined by friction stir welding. A cutting pin of rotary burr made of tungsten carbide was employed. The microstructures of the joining interface were observed by scanning electron microscopy. Joint strength was evaluated by a tensile shear test. During the welding process, the surface layer of the titanium plate was cut off by the pin, and intensively mixed with aluminum situated on the titanium plate. The microstructures analysis showed that a visible swirl-like mixed region existed at the interface. In this region, the Al metal, Ti metal and the mixed layer of them were all presented. The ultimate tensile shear strength of joint reached 100% of 1060Al that underwent thermal cycle provided by the shoulder. - Highlights: Black-Right-Pointing-Pointer FSW with cutting pin was successfully employed to form Al/Ti lap joint. Black-Right-Pointing-Pointer Swirl-like structures formed due to mechanical mixing were found at the interface. Black-Right-Pointing-Pointer High-strength joints fractured at Al suffered thermal cycle were produced.

36 MATERIALS SCIENCE↗

Laser shock peening effect on the dislocation transitions and grain refinement of Al–Mg–Si alloy

This paper systematically investigates the effect of laser shock peening without coating parameters on the microstructural evolution, and dislocation configurations induced by ultra-high plastic strains and strain rates. Based on an analysis of optical microscopy, polarized light microscopy, transmission electron microscopy observations and residual stress analysis, the significant influence of laser shock peening parameters due to the effect of plasma generation and shock wave propagation has been confirmed. Although the optical microscopy results revealed no significant microstructural changes after laser shock peening, i.e. no heat effect zone and differences in the distribution of second-phase particles, expressive influence of laser treatment parameters on the laser shock induced craters was confirmed. Moreover, polarized light microscopy results have confirmed the existence of well-defined longish grains up to 455 μm in length in the centre of the plate due to the rolling effect, and randomly oriented smaller grains (20 μm × 50 μm) in the surface due to the static recrystallization effect. Laser shock peening is reflected in an exceptional increase in dislocation density with various configurations, i.e. dislocation lines, dislocation cells, dislocation tangles, and the formation of dense dislocation walls. More importantly, the microstructure is considerably refined due to the effect of strain deformations induced by laser shock peening process. The results have confirmed that dense dislocation structures during ultra-high plastic deformation with the addition of shear bands producing ultra-fine (60–200 nm) and nano-grains (20–50 nm). Furthermore, dislocation density was increased by a factor of 2.5 compared to the untreated material (29 × 10{sup 13} m{sup −2} vs. 12 × 10{sup 13} m{sup −2}). - Highlights: • LSPwC imparts high compressive residual stresses up to − 362 ± 31 MPa. • After LSPwC the microstructure is considerably refined via dislocation transitions. • Results confirmed ultra-fine (60–200 nm) and nano-grains (20–50 nm) after LSPwC. • Reasonable agreements between dislocation density and residual stress are obtained.

36 MATERIALS SCIENCE↗

Texture evolution of an Fe–Ni alloy sheet produced by cross accumulative roll bonding

The texture evolution in an Fe–36%Ni (wt.%) alloy, severely deformed to a true strain of 4.8 by cross accumulative roll bonding, was investigated using X-ray diffraction and a visco-plastic self-consistent simulation. At the surface, the C component ((100)<011>) exhibited a strong continuous strengthening from cycles 1 to 5. At the mid-thickness region, the texture evolution appeared to be cyclic due to the cyclic nature of the imposed deformation. A copper-type texture was observed even after cycles, whereas a new major texture component named H ((012)<22{sup ¯}1>) was formed after odd cycles, with several other minor ones belonging to a (210) fiber. A significant change in the plastic anisotropy was introduced by cross accumulative roll bonding processing. - Highlight: • The texture after CARB is characterized by a typical C shear component near the surface. • The texture evolution in the mid thickness of samples seen to be cyclic • VPSC model reproduced the experimental texture in the early CARB cycle. • The CARB process can reduce the plastic anisotropy of the sheet.

36 MATERIALS SCIENCE↗

Micro-structural evolution during diffusion bonding of C-SiC/C-SiC composite using Ti interlayer

Highlights: • Formation of Ti{sub 3}SiC{sub 2} MAX phase in the joint of C-SiC composite • EBSD revealed three zone microstructure of the joint • Formation of a thin continuous layer of TiSi{sub 2} • The apparent shear strength of 19 MPa - Abstract: Diffusion bonding of C-SiC composite was achieved with Ti interlayer at 1500 °C for 3 h with the applied pressure of 20 MPa. The joined C-SiC composite showed the apparent shear strength of 19 MPa and the sample fractured away from the joint. The microstructure of joint consists of Ti{sub 3}SiC{sub 2} MAX phase, TiSi{sub 2} and TiC in which Ti{sub 3}SiC{sub 2} was the major phase. The distribution of phases in the microstructure of joint was categorized into three different zones based on electron backscattered diffraction (EBSD) results. The first zone consists of a thin continuous TiSi{sub 2} phase, which was followed by a thick zone of Ti{sub 3}SiC{sub 2} MAX phase. In the middle of the sample, a mix phase zone was found. The reaction mechanism was established for the evolution above microstructure of joined C-SiC composite.

36 MATERIALS SCIENCE↗

Direct diffusion bonding of Ti{sub 3}SiC{sub 2} and Ti{sub 3}AlC{sub 2}

Two typical layered ternary compounds, Ti{sub 3}SiC{sub 2} and Ti{sub 3}AlC{sub 2}, were joined directly by solid-state diffusion bonding method. By various bonding tests at 1100-1300 deg. C for 30-120 min under 10-30 MPa, and characterizing the microstructure and diffusion reactive phases of the joints by scanning electron microscopy (SEM), energy dispersive X-ray spectrometer (EDS), transmission electron microscopy (TEM) and X-ray diffraction (XRD), the optimal condition for direct joining of Ti{sub 3}SiC{sub 2} and Ti{sub 3}AlC{sub 2} was obtained. Strong joints of Ti{sub 3}SiC{sub 2}/Ti{sub 3}AlC{sub 2} can be achieved via diffusion bonding, which is attributed to remarkable interdiffusion of Si and Al at the joint interface. The shear strength of the Ti{sub 3}SiC{sub 2}/Ti{sub 3}AlC{sub 2} joints was determined.

36 MATERIALS SCIENCE↗

Comparison of slope stability in two Brazilian municipal landfills

The implementation of landfill gas to energy (LFGTE) projects has greatly assisted in reducing the greenhouse gases and air pollutants, leading to an improved local air quality and reduced health risks. The majority of cities in developing countries still dispose of their municipal waste in uncontrolled 'open dumps.' Municipal solid waste landfill construction practices and operating procedures in these countries pose a challenge to implementation of LFGTE projects because of concern about damage to the gas collection infrastructure (horizontal headers and vertical wells) caused by minor, relatively shallow slumps and slides within the waste mass. While major slope failures can and have occurred, such failures in most cases have been shown to involve contributory factors or triggers such as high pore pressures, weak foundation soil or failure along weak geosynthetic interfaces. Many researchers who have studied waste mechanics propose that the shear strength of municipal waste is sufficient such that major deep-seated catastrophic failures under most circumstances require such contributory factors. Obviously, evaluation of such potential major failures requires expert analysis by geotechnical specialists with detailed site-specific information regarding foundation soils, interface shearing resistances and pore pressures both within the waste and in clayey barrier layers or foundation soils. The objective of this paper is to evaluate the potential use of very simple stability analyses which can be used to study the potential for slumps and slides within the waste mass and which may represent a significant constraint on construction and development of the landfill, on reclamation and closure and on the feasibility of a LFGTE project. The stability analyses rely on site-specific but simple estimates of the unit weight of waste and the pore pressure conditions and use 'generic' published shear strength envelopes for municipal waste. Application of the slope stability analysis method is presented in a case study of two Brazilian landfill sites; the Cruz das Almas Landfill in Maceio and the Muribeca Landfill in Recife. The Muribeca site has never recorded a slope failure and is much larger and better-maintained when compared to the Maceio site at which numerous minor slumps and slides have been observed. Conventional limit-equilibrium analysis was used to calculate factors of safety for stability of the landfill side slopes. Results indicate that the Muribeca site is more stable with computed factors of safety values in the range 1.6-2.4 compared with computed values ranging from 0.9 to 1.4 for the Maceio site at which slope failures have been known to occur. The results suggest that this approach may be useful as a screening-level tool when considering the feasibility of implementing LFGTE projects.

54 ENVIRONMENTAL SCIENCES↗

A design chart for estimation of horizontal displacement in municipal landfills

This paper describes the development of a design chart for the estimation of maximum horizontal displacement within a municipal landfill using the height and the side slope of the landfill. The design chart is based on the results of a finite element parametric study in which the behaviour of the municipal solid waste (MSW) was modeled using a non-linear elastic hyperbolic model. The model input parameters, i.e. non-linear stiffness, shear strength and unit weight of MSW, were obtained from laboratory testing data and an extensive stochastic numerical modelling exercise. Non-linear variations of unit weight as well as Young's modulus of MSW with depth were incorporated in the finite element analyses. The validity of the design chart was assessed using field monitoring results from a large landfill located in Ontario, Canada.

42 ENGINEERING↗

Rheological study of comingled biomass and coal slurries with hydrothermal pretreatment

Gasification of comingled biomass and coal feedstock is an effective means of reducing the net life cycle greenhouse gas emissions in the coal gasification process while maintaining its inherent benefits of abundance and high-energy density. However, feeding a comingled biomass and coal feedstock into a pressurized gasification reactor poses a technical problem. Conventional dry feeding systems, such as lock hoppers and pressurized pneumatic transport, are complex and operationally expensive. A slurry formation of comingled biomass and coal feedstock can be easily fed into the gasification reactor but, in normal conditions, only allows for a small portion of biomass in the mixture. This is a consequence of the hydroscopic and hydrophilic nature of the biomass. The College of Engineering Center for Environmental Research and Technology (CE-CERT) at the University of California, Riverside, has developed a process producing high solid content biomass-water slurry using a hydrothermal pretreatment process. In this paper, the systematic investigation of the rheological properties (e.g., shear rate, shear stress, and viscosity) of coal-water slurries, biomass-water slurries, and comingled biomass and coal-water slurries is reported. The solid particle size distribution in the slurry and the initial solid/water ratio were investigated to determine the impact on shear rate and viscosity. This was determined using a rotational rheometer. The experimental results show that larger particle size offers better pumpability. The presence of a high percentage of biomass in solid form significantly decreases slurry pumpability. It is also shown that the solid loading of the biomass-water slurry can be increased to approximately 35 wt % with viscosity of less than 0.7 Pa.s after the pretreatment process. The solid loading increased to approximately 45 wt % when the biomass is comingled with coal. 18 refs., 7 figs., 3 tabs.

01 COAL, LIGNITE, AND PEAT↗

Programmable nanowrinkle-induced room-temperature exciton localization in monolayer WSe2

Abstract Localized states in two-dimensional (2D) transition metal dichalcogenides (TMDCs) have been the subject of intense study, driven by potential applications in quantum information science. Despite the rapidly growing knowledge surrounding these emitters, their microscopic nature is still not fully understood, limiting their production and application. Motivated by this challenge, and by recent theoretical and experimental evidence showing that nanowrinkles generate strain-localized room-temperature emitters, we demonstrate a method to intentionally induce wrinkles with collections of stressors, showing that long-range wrinkle direction and position are controllable with patterned array design. Nano-photoluminescence (nano-PL) imaging combined with detailed strain modeling based on measured wrinkle topography establishes a correlation between wrinkle properties, particularly shear strain, and localized exciton emission. Beyond the array-induced wrinkles, nano-PL spatial maps further reveal that the strain environment around individual stressors is heterogeneous due to the presence of fine wrinkles that are less deterministic. At cryogenic temperatures, antibunched emission is observed, confirming that the nanocone-induced strain is sufficiently large for the formation of quantum emitters. At 300 K, detailed nanoscale hyperspectral images uncover a wide range of low-energy emission peaks originating from the fine wrinkles, and show that the states can be tightly confined to regions <10 nm, even in ambient conditions. These results establish a promising potential route towards realizing room temperature quantum emission in 2D TMDC systems.

36 MATERIALS SCIENCE↗

Experimental Analyses of Yellow Tuff Spandrels of Post-medieval Buildings in the Naples Area

Experimental analyses have been carried out on tuff masonry specimens in order to investigate the structural behaviour of historical buildings in the Naples area (Southern Italy). Spandrels of post-medieval buildings (late XVI to early XX century) have been analysed, with emphasis on morphological characteristics according to chronological indicators. Results of the experimentation on scaled models (1:10) are discussed and the better behaviour of historical masonry typologies on respect to the modern one is highlighted. Comparison with theoretical formulations of ultimate shear resistance are provided too.

58 GEOSCIENCES↗

Shear Strength Prediction By Modified Plasticity Theory For SFRC Beams

the plastic Crack Sliding Model (CSM) is extended for derivation of a physical model for the prediction of ultimate shear strength of SFRC beams, by assuming that the critical cracks is modeled by a yield lines. To this aim, the CSM is improved in order to take into account the strength increases due to the arch effect for deep beam. Then, the effectiveness factors for the concrete under biaxial stress are calibrated for fibrous concrete. The proposed model, able to provide the shear strength and the position of the critical cracks, is validate by a large set of test results collected in literature.

58 GEOSCIENCES↗

Experimental Evaluation of Beam to Diamond Box Column Connection with Through Plate in Moment Frames

Moment resisting frames with built up section have very enhanced features due to high bending stiffness and strength characteristics in two principal axes and access to column faces for beam to column easy connections. But due to proper transfer of beam stresses to column faces there were always some specific controvertibly issues that how to make the load transfer through and in plane manner in order to mobilize the forces in column faces. Using diamond column instead of box column provide possibility to mobilize the load transfer mechanism in column faces. This section as a column has considerable benefit such as high plastic to elastic section modulus ratio which is an effective factor for force controlled components. Typical connection has no chance to be applied with diamond column.This paper elucidates the seismic behavior of through-plates moment connections to diamond box columns for use in steel moment resisting frames. This connection has a lot of economical benefits such as no need to horizontal continuity plates and satisfying the weak beam--strong column criteria in the connection region. They might serve as panel zone plates as well. According to high shear demand in panel zone of beam to column joint one should use the doublers plates in order to decrease the shear strength demand in this sensitive part of structure but these plates have no possibility to mobilize the load transfer mechanism in column web and transfer them to column flanges. In this type of connection, column faces have effective role in order to decrease the demands on through plate and they are impressive factors for improving the performance of the connection.Experimental analysis was conducted to elucidate the seismic behavior of this connection. The results of Experimental analysis established the effectiveness of the through plate in mitigating local stress concentrations and forming the plastic hinge zone in the beam away from the beam to column interface. The moment-rotation graphs form sub-assemblage show a desirable seismic performance of this connection.

58 GEOSCIENCES↗

Coherent Dynamics of meta-Toluidine Investigated by QuasiElastic Neutron Scattering

The coherent dynamics of a typical fragile glass former, meta-toluidine, was investigated at the molecular level using quasielastic neutron scattering, with time-of-flight and neutron spin echo spectrometers. It is well known that the static structure factor of meta-toluidine shows a prepeak originating from clustering of the molecules through hydrogen bonding between the amine groups. The dynamics of meta-toluidine was measured for several values of the wavevector transfer Q, which is equivalent to an inverse length scale, in a range encompassing the prepeak and the structure factor peak. Data were collected in the temperature range corresponding to the liquid and supercooled states, down to the glass transition. At least two dynamical processes were identified. This paper focuses on the slowest relaxation process in the system, the {alpha}-relaxation, which was found to scale with the macroscopic shear viscosity at all the investigated Q values. No evidence of 'de Gennes' narrowing associated with the prepeak was observed, in contrast with what happens at the Q value corresponding to the interparticle distance. Moreover, using partially deuterated samples, the dynamics of the clusters was found to be correlated to the single-particle dynamics of the meta-toluidine molecules.

08 HYDROGEN↗

Postmortem analysis of sand grain crushing from pile interface using X-ray tomography

Pile foundations of offshore platforms, wind and water turbines are typically subjected to a variety of cyclic loading paths due to their complex environment. While many studies focus on global pile behaviour, the soil-pile interface is explored here by a micromechanical study of the soil layer in contact with the pile surface. This work is devoted to the analysis of frozen post-mortem silica sand samples recovered at the pile interface following installation and cyclic loading tests in a calibration chamber using x-ray tomography. An experimental procedure developed for three dimensional (3D) snow imaging was adapted for the recovery of the in-situ sand samples to preserve their structure during tomography scans. 3D images at a pixel size of 7 {mu}m were then obtained using a cryogenic cell. Results confirm the presence of a shear band at the pile surface as well as void ratios changes in the direction of the pile's radius.

36 MATERIALS SCIENCE↗

Strength and equation of state of NaCl from radial x-ray diffraction

The strength and equation of state of NaCl were determined under nonhydrostatic compression up to 27 GPa using an energy-dispersive radial x-ray diffraction technique in a diamond-anvil cell using the lattice strain theory. Together with estimation of the high-pressure shear modulus, it is suggested that NaCl could support a maximum differential stress of 0.980 GPa at 22.6 GPa under uniaxial compression. The differential stress rapidly drops at 27.2 GPa due to the phase transition from B1 phase to B2 phase for NaCl. The hydrostatic compression data of B1 phase yield a bulk modulus K{sub 0} = 25.6(8) GPa and its pressure derivative K{sub 0}′ = 5.16(20) using Pt pressure scale. In addition, a comparative study of the observed pressures from Pt scale and ruby-fluorescence scale shows that the ruby-fluorescence pressures may reflect the lower stress state under nonhydrostatic compression compared with hydrostatic compression.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Short-range correlations control the G/K and Poisson ratios of amorphous solids and metallic glasses

The bulk modulus of many amorphous materials, such as metallic glasses, behaves nearly in agreement with the assumption of affine deformation, namely that the atoms are displaced just by the amount prescribed by the applied strain. In contrast, the shear modulus behaves as for nonaffine deformations, with additional displacements due to the structural disorder which induce a marked material softening to shear. The consequence is an anomalously large ratio of the bulk modulus to the shear modulus for disordered materials characterized by dense atomic packing, but not for random networks with point atoms. We explain this phenomenon with a microscopic derivation of the elastic moduli of amorphous solids accounting for the interplay of nonaffinity and short-range particle correlations due to excluded volume. Short-range order is responsible for a reduction of the nonaffinity which is much stronger under compression, where the geometric coupling between nonaffinity and the deformation field is strong, whilst under shear this coupling is weak. Predictions of the Poisson ratio based on this model allow us to rationalize the trends as a function of coordination and atomic packing observed with many amorphous materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Understanding the deformation mechanism of individual phases of a ZrTi-based bulk metallic glass matrix composite using in situ diffraction and imaging methods

The plasticity of a ZrTi-based bulk metallic glass composite consisting of glassy matrix and crystalline dendritic phase was studied in-situ under identical tensile loading conditions using scanning electron microscopy and synchrotron X-ray diffraction. A generic procedure was developed to separate the diffraction information of the crystalline phases away from that of the matrix and to precisely calculate the microscopic strains of the two phases at different macroscopic load steps. In this way, the time-evolved quantitative links between shear bands nucleation/propagation and the corresponding microscopic stress fields around them are established, providing more quantitative understanding on (1) how the shear bands are driven by the local stress field, and (2) the critical stresses required for the shear bands to nucleate in the crystalline phase, propagate through the crystalline/matrix interface, and finally into the matrix.

36 MATERIALS SCIENCE↗