Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RODS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Management of Irradiated Control Rods: Cost of an Industrial Approach - 18009

This paper concerns the sorting of irradiated control rods that can be done to limit the volume of Intermediate Level Long-lived Waste. More specifically it assesses the cost of an industrial approach. For this we used numerical simulations, penalizing hypotheses and measurements. The cost is given in term of the increased volume of the control rods placed into deep geological storage. To calculate the radioactive inventories, we have developed a calculation scheme which includes a mapping of the neutron flux, a calculation of the isotopic compositions evolution, and a validation of the results. For the state of the art simulations, all operational fuel loading patterns were considered and coupled with all effective power distributions. The analysis of the calculated results shows that the simulations produce a slight overestimation of the measurements. For envelope simulations, penalizing fuel loading patterns and nominal power distribution conditions were used. Most of the radionuclides needed to declare the radiological inventories are difficult to measure. Therefore, for each radionuclide a scaling factor referred to a key radionuclide, can be calculated. Then during the dismantling operations these calculated scaling factors are multiplied by the measured key radionuclide to determine the radiological inventory. The industrial approach consists of combining envelope simulations with scaling factors. Applied to PWR control rods, the industrial approach overestimates the radiological inventories by a factor of 2. As such, the calculated position of the Intermediate Level Long Lived part limit moves +6 cm. Compared to the 1 meter of the control rod pins classified as Intermediate Level Long Lived, the industrial approach would increase by 6 % the volume of the control rods placed into the deep geological storage. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Mapping Turbulent Flow around a Rod Bundle Induced by a 5 x 5 PWR Mixing Vane Grid using Particle Tracking Velocimetry

This study presents an experimental visualization technique developed for the measurement of the lateral liquid velocity components within a vertical up-flow 5 x 5 rod bundle. The experimental technique uses refractive index matching (RIM) and time resolved particle tracking velocimetry (PTV) to obtain full field measurements at different axial locations. Relevant features of the technique are first, the multi-scale capability, which allows measurements either on a single subchannel or measurements to include the full bundle accounting for the 25 rods and corresponding liquid subchannels. Secondly, the use of FEP tubes to match the refractive index of water allows a uniform illumination which in turn reduces the velocity measurements uncertainty, and third, the use of a high energy continuous laser allows for the temporal evaluation of fluctuating structures within the bundle. This study was conducted with the aim to quantify the effect of the mixing vanes on the development of the liquid turbulence and to test the motivation feasibility of the technique to serve as a benchmark for advanced CFD simulations. In this context, there have been multiple experimental studies with the objective to improve the database for CFD benchmarking purposes. Several experimental techniques have been used to this end; for instance, laser doppler velocimetry (LDV) is a preferred tool to measure the axial and lateral velocity components through bundles due to its accuracy. Although LDV is a mature technique, it only provides point measurements which do not allow for the instantaneous investigation of the momentum exchange among neighboring subchannels; moreover, the small spaces between the rods and within the subchannels makes LDV measurements difficult. In the other hand, flow visualization techniques can provide a 2D map of the instantaneous and average structure of the liquid velocity. Among the used visualization techniques, PIV has gained a lot of attention due to its high accuracy, relative simple application, and non-intrusiveness. Several studies had applied PIV to study the flow structures within bundles sub-channels with some success; however, in these studies there exist an increased uncertainty due to reflections and shadows from the rods. Shadows and undesired reflections appear when the light passes through materials with different refractive indexes. This issue was addressed in other studies on which the refractive index of the rod bundle (or sections of it) was matched with that of water. These studies used particle tracking velocimetry (PTV) and obtained comparable results with LDV measurements. This success indicated that RIM-PTV experiments can be successfully implemented to gather information for simulation benchmarking. The present work is an extension of previous efforts on which measurements were performed only on vertical planes but lacked of the important flow structures that can only be observed through a horizontal cross section of the bundle at different axial height. The focus of the present study was to fill this information gap by measuring the lateral velocity in horizontal planes at different heights. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Comparing Velocity Profiles Along the Rod Length of a Helical Coil Steam Generator Model

A model of a specific type of tube and shell heat exchanger, the helical coil steam generator (HCSG), was designed and constructed to study multiple fluidic properties that attribute to the efficiency of the heat transfer it provides. Tube and shell heat exchangers are currently used throughout industry in chemical, power and petroleum engineering. Most commonly, a primary flow is circulated through a shell, while the secondary flow is run through several small tubes that are bundled together. Methods to increase the heat transfer between the two flows include adding baffles to force shell side flow over more tubes, fins added in-between layers of tubes and passing tubes multiple times through the shell to increase heat exchanger effectiveness. The HCSG incorporates many of the proposed methods but also relies on a complex geometry to increase the heat transfer between tube and shell side flow. In an area where cost effectiveness is favorable, such as inside a nuclear reactor, helically banked steam generators makes extensive use of the room with no sharp tube bends. This increases the pressure loss on the secondary flow and can solve potential temperature manufacturing issues at the welds of junctions. Additionally, they have exhibited pure cross flow behaviors with high heat transfer coefficients and axial temperature profiles that correspond to pure counter-flow with high mean temperature differences. Early work showed that helical banks can have a significant increase of 16 to 43% higher heat transfer coefficient than straight pipe heat exchangers. While many previous studies have looked at the heat transfer, pressure drop and flow fields of a tube and shell heat exchanger, they all focus on tube bundles that are either in-line or staggered. The early flow visualization studies on these types of bundle arrangements reported that attached eddies were formed alternatively behind each of the rods and were occasionally dragged into the main stream of shell side flow. Later studies suggested that observable periodic vortex shedding was dependent on geometry. Experimental data taken using techniques such as laser Doppler anemometry (LDV) by Simonin and Barcouda (1986) as mentioned in Hassan (2002), hot-wire anemometry with Tsuchida (1982) and particle image velocimetry (PIV) conducted by researchers as late as 2007 have been used to characterize turbulent flow and distinguish flow field structures within in-line and staggered tube bundles. By studying these flow field structures, their contribution to fluidic properties such as heat transfer efficiency and pressure drop can be characterized effectively. Literature review lead to a design that incorporated five layers of coils wrapped around one another. The outermost and middle layers of tubes coiled at a specific pitch in a clockwise direction while the other two layers coiled counterclockwise. The proposed design incorporates a constantly changing lateral pitch ratio, a, between adjacent rods. The constructed test section isolates a single interface between two adjacent coiling rod bundles of twelve rods. Three distinct cross sectional planes along the rod bundles were looked at to study the effect of the local geometry to flow fields, Section A, B and C. Particle Image Velocimetry (PIV) frames of 896 x 848 pixels were captured at each section across a specific height. Profiles of mean velocity fields for each section are compared and discussed as possible features of the changing lateral pitch ratio.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

MECHANISTIC MULTIPHYSICS MODELING OF CLADDING RUPTURE IN NUCLEAR FUEL RODS DURING LOSS-OF-COOLANT ACCIDENT CONDITIONS

The Loss of Coolant Accident (LOCA) is a design basis accident that is included as part of the safety analysis of nuclear power plants. As the nuclear industry desires to increase the cycle length and discharge burnup of existing nuclear power plants they must demonstrate safe operation during a LOCA on high burnup fuel. During a LOCA transient on high burnup fuel rods, the rods may undergo a process known as fuel fragmentation, relocation, and dispersal (FFRD). To permit dispersal, the cladding encapsulating the fuel must rupture with an opening size large enough to allow the fragmented fuel particles to release. Current licensing tools used by industry and the United States Nuclear Regulatory Commission are limited in geometric fidelity and materials that can be analyzed. These simulation tools generally employ a quasi-two-dimensional (1.5D or Layered1D) or 2D-RZ axisymmetric geometric representations exclusively. While a valid approach under some instances, there are times when important physics have an asymmetric behavior in the fuel rod. Examples include fuel fragmentation, thermal-hydraulic boundary conditions, and cladding rupture, all of which are important for LOCA analysis. As industry pursues burnup extensions it must be demonstrated that fuel dispersal can be mitigated or eliminated. To do this, an understanding of the rupture opening after cladding failure is required. This work presents the development of a model for predicting the size and location of the rupture opening in failed fuel rods during LOCA conditions using advanced modeling and simulation tools. In order to supply the rupture model with appropriate boundary conditions, improvements to fuel fragmentation, axial relocation and oxidation modeling were required. First, the eXtended Finite Element Method (XFEM) is used to mechanistically predict the number of fuel fragments that form due to material strength randomization, criteria for strength randomization, mesh density, power ramping rates and irradiation effects. These predictions with associated uncertainty were compared to empirical correlations developed for UO2 verifying that they can be used with increased confidence in subsequent axial relocation analyses. Secondly, a new first-of-its-kind Layered2D computational framework was developed that provides the ability to apply azimuthally varying boundary conditions while providing discrete layers to track fuel movement during the LOCA. An existing fuel axial relocation model developed for Layered1D was extended to work within the Layered2D framework. A large sensitivity study was performed on the initial version of the model to identify modeling parameters of particular importance, with the emissivity used for radiation after blowdown being the primary source of uncertainty. Then, a simplistic approach to incorporate mechanical degradation of the cladding due to oxidation was also developed to investigate the impact of reduced cladding thickness on predictions of the time to failure of cladding tubes. It was found that the cladding will typically rupture prior to a reduction in thickness that is sufficient to impact the rupture behavior. A model was then developed for predicting cladding rupture that transfers the cladding surface temperatures, rod internal and external pressures, fast neutron fluence, and fast neutron flux from a more detailed Layered1D, Layered2D, or 2D-RZ analysis to a 3D cladding only analysis. Comparisons of the rupture model to a few experiments indicate reasonable predictions. The rupture model was then applied to two accident tolerant fuel concepts (FeCrAl and Cr-coated Zircaloy) where it predicted that both ATF concepts would have smaller rupture openings and delayed rupture times than the standard Zircaloy-4 cladding material under identical loading conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Hydride Reprecipitation in Prototypical 17x17 PWR Fuel Rods after Simulated Vacuum Drying Conditions

Light water reactor (LWR) fuel rod cladding picks up hydrogen as it oxidizes in reactor. Once the hydrogen concentration exceeds the solubility limit, zirconium hydride platelets precipitate, generally in the circumferential direction. In preparation for dry storage, elevated temperatures can dissolve some of the circumferential hydrides, which during cooling can then reprecipitate in a direction perpendicular to the hoop stress (radially). From 2019 to 2024, ORNL published a series of reports that included metallographic observations of cladding after a thermal transient to 400°C followed by slow cooling. The simulated dry storage process was performed on three full-length 17x17 PWR fuel rods at their as-discharged rod internal pressure. There were two important observations from the metallographic examinations of these heat-treated rods: (1) the propensity for hydride reorientation is strongly influenced by nearby as-discharged precipitated hydrides, (2) the radial hydrides observed near the cladding inner diameter were often associated with cracks in the pellet. Subsequent modeling using the BISON fuel performance code that considered the effects of pellet cracks and pellet-cladding bonding observed in high-burnup fuel support the conclusion that pellet cracks enhance the local hoop stress in the cladding creating preferential sites for hydride reorientation, and that the influence of the pellet cannot be ignored in accurate fuel rod performance predictions.

Montgomery, Rose [ORNL] (ORCID:0000000286038936)↗

Power Burst Facility: U(18)O2-CaO-ZrO2 Fuel Rods in Water

The Power Burst Facility (PBF) reactor operated from 1972 to 1985 on the SPERT Area I of the Idaho National Laboratory, then known as Nuclear Reactor Test Station. PBF was designed to provide experimental data to aid in defining thresholds for and modes of failure under postulated accident conditions. PBF reactor startup testing began in 1972. This evaluation focuses on two operational loading tests, chronologically numbered 1 and 2, published in a startup-test report in 1974 [1]. Data for these tests was used by one of the authors to validate a MCNP model for criticality safety purposes [2]. Although specific references to original documents are kept in the text, all the reactor parameters and test specific data presented here was adapted from that report. The tests were performed with operational fuel loadings, a stainless steel in-pile tube (IPT) mockup, a neutron source, four pulse chambers, two fission chambers, and one ion chamber. The reactor's four transition rods (TRs) and control rods (CRs) were present but TR boron was completely withdrawn below the core and CR boron was partially withdrawn above the core. Test configurations differ primarily in the number of shim rods, and consequently the number of fuel rods included in the core. The critical condition was approached by incrementally and uniformly withdrawing CR boron from the core. Based on the analysis of the experimental data and numerical calculations, both experiments are considered acceptable as criticality safety benchmarks.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Coupled thermal analysis applied to the study of the rod ejection accident

An advanced methodology for the assessment of fuel-rod thermal margins under RIA conditions has been developed by AREVA NP SAS. With the emergence of RIA analytical criteria, the study of the Rod Ejection Accident (REA) would normally require the analysis of each fuel rod, slice by slice, over the whole core. Up to now the strategy used to overcome this difficulty has been to perform separate analyses of sampled fuel pins with conservative hypotheses for thermal properties and boundary conditions. In the advanced methodology, the evaluation model for the Rod Ejection Accident (REA) integrates the node average fuel and coolant properties calculation for neutron feedback purpose as well as the peak fuel and coolant time-dependent properties for criteria checking. The calculation grid for peak fuel and coolant properties can be specified from the assembly pitch down to the cell pitch. The comparative analysis of methodologies shows that coupled methodology allows reducing excessive conservatism of the uncoupled approach. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

limiting rods selection in large break LOCA analysis with the RELAP5-3D code

The Nuclear Regulatory Commission (NRC) is proposing a new rulemaking on emergency core system/loss-of-coolant accident (LOCA) performance analysis. In the proposed rulemaking, designated as 10 CFR 50.46(c), the US NRC put forward an equivalent cladding oxidation criterion as a function of cladding pre-transient hydrogen content. The proposed rulemaking imposes more restrictive and burnup-dependent cladding embrittlement criteria; consequently more fuel rods need to be analyzed under LOCA conditions to maintain the safety margin, compared to the current practice in which only one hot rod needs to be analyzed. New analysis methods are required to provide a thorough characterization of the reactor core in order to identify the locations of the limiting rods under LOCA conditions. In this work, the best-estimate plus uncertainty analysis capability for large break LOCA with the new cladding embrittlement criteria using the RELAP5-3D code is established and demonstrated with a reduced set of uncertainty parameters. With the new analysis method, the limiting transient case and the limiting rods can be easily identified in response to the proposed new rulemaking. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Preliminary design of control rods in the single-fluid double-zone thorium molten salt reactor (SD-TMSR)

Recent studies on Molten Salt Reactors (MSRs) showed that the excess reactivity at the beginning of the operation is large for many fueling strategies and must be compensated by a reactivity control system. The current work introduces a reliable safety system based on control rods in addition to the online feed system reactivity control in the Single-fluid Double-zone Thorium-based Molten Salt Reactor (SD-TMSR). Three different initial fissile loadings are considered: 233 U, reactor-grade Pu, and transuranic (TRU) elements as a startup fuel. We applied six different absorbing materials to investigate the main operational and safety parameters in the SD-TMSR: natural B 4 C, enriched B 4 C with 90% 10 B, HfB 2 , HfH 1.62 , Eu 2 O 3 , and Gd 2 O 3 . The present work focuses on control rod design, integral and differential control rod worth, shutdown margin, and shadowing effects at steady-state. We employed the SERPENT-2 Monte-Carlo code to calculate the reactivity worth and analyze the performance of the reactivity control system. We showed that 233 U and reactor-grade Pu startup cores maintain adequate shutdown margin with all considered absorbers. Finally, this report proposes a design of control rod clusters that compensate the excess reactivity of the SD-TMSR loaded with different initial fissile material.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Experimental measurements of fluid flow in an 84-pin hexagonal rod bundle with spacer grid for a gas-cooled fast modular reactor

A 50 MW e helium-cooled fast modular reactor (FMR) is under development, and as part of the Department of Energy Integrated Research Project (IRP), Texas A&M University is conducting the thermal-hydraulic characterization of its baseline core configuration. Here, we experimentally investigated the axial and cross flow fields characteristics in the hexagonal fuel rod bundle composed of 84 rods, a central rod, and spacer grids at a Reynolds number of 12,000. A fully transparent experimental facility resembling of one unit of the fuel assembly was constructed. Time-resolved particle image velocimetry (TR-PIV) measurements were performed to characterize hydraulic behavior downstream the spacer grid. Velocity measurements were conducted in the axial and radial direction of the rod bundle. From the PIV velocity vector fields, the full-field flow statistics were computed for the mean velocity, vorticity, and Reynolds stresses. An analysis of the energy decay downstream of the spacer grid was conducted with calculations of secondary-flow intensities, turbulent kinetic energy, power spectrum, and spatial-temporal velocity cross correlations. The vorticity field was obtained and pairs of counter-rotating vortexes were identified using a 3D reconstruction of several measurement planes. The data from this experimental campaign will be used to validate numerical models based on Computational Fluid Dynamics and other codes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Failure and penetration response of borosilicate glass during short-rod impact

The failure characterization of brittle materials like glass is of fundamental importance in describing the penetration resistance against projectiles. A critical question is whether this failure front remains 'steady' after the driving stress is removed. A test series with short gold rods (D = 1 mm, L/D{approx_equal}5-11) impacting borosilicate glass at {approx}1 to 2 km/s was carried out to investigate this question. The reverse ballistic method was used for the experiments, and the impact and penetration process was observed simultaneously with five flash X-rays and a 16-frame high-speed optical camera. Very high measurement accuracy was established to ensure reliable results. Results show that the failure front induced by rod impact and penetration does arrest (ceases to propagate) after the rod is totally eroded inside the glass. The impact of a second rod after a short time delay reinitiates the failure front at about the same speed.

36 MATERIALS SCIENCE↗

Dispersion of an optodynamic wave during its multiple transitions in a rod

A rod acquires linear momentum during a short-laser-pulse ablation of its front face. Initially, this momentum is localized within the propagating laser-induced mechanical pulse--the optodynamic wave--while later it is gradually transferred to the uniform motion of the entire rod. Among other effects, the dispersion of the optodynamic wave due to lateral inertia plays an important role in the linear-momentum transformation mechanism. We observed the dispersion using interferometric measurements of the rod's rear-end staircaselike displacement. The displacements calculated using an analytical solution of Love's equation for a laser-ablated free-free homogeneous rod agree well with our measured data.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

The influences of geometric shape of cross section on equilibrium configuration of DNA in elastic rod model

The equilibrium configuration equations of DNA chain with elastic rod model are derived in detail by the variation of the free energy functional, which depends on the curvature, torsion, twisting angle and its derivative with respect to the arc-length of central axis curve of rod. With the different shapes of rod, we obtain the equilibrium equations of DNA with circular and noncircular cross sections, which provide an approach to describe the physical behaviors of A-, B-, Z-DNA. The results show that the elastic rod model with circular cross section can accurately characterize the equilibrium configurations of A-, B-DNA, while the model with elliptical cross sections is more suitable for Z-DNA.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Defect reduction in overgrown semi-polar (11-22) GaN on a regularly arrayed micro-rod array template

We demonstrate a great improvement in the crystal quality of our semi-polar (11-22) GaN overgrown on regularly arrayed micro-rod templates fabricated using a combination of industry-matched photolithography and dry-etching techniques. As a result of our micro-rod configuration specially designed, an intrinsic issue on the anisotropic growth rate which is a great challenge in conventional overgrowth technique for semi-polar GaN has been resolved. Transmission electron microscopy measurements show a different mechanism of defect reduction from conventional overgrowth techniques and also demonstrate major advantages of our approach. The dislocations existing in the GaN micro-rods are effectively blocked by both a SiO{sub 2} mask on the top of each GaN micro-rod and lateral growth along the c-direction, where the growth rate along the c-direction is faster than that along any other direction. Basal stacking faults (BSFs) are also effectively impeded, leading to a distribution of BSF-free regions periodically spaced by BSF regions along the [-1-123] direction, in which high and low BSF density areas further show a periodic distribution along the [1-100] direction. Furthermore, a defect reduction model is proposed for further improvement in the crystalline quality of overgrown (11-22) GaN on sapphire.

36 MATERIALS SCIENCE↗

Implementation of a Spacer Grid Rod Thermal-Hydraulic Reconstruction (ROTHCON) Capability into the Thermal-Hydraulic Subchannel Code CTF

The Consortium for Advanced Simulation of Light Water Reactors is developing a core simulator capability known as the Virtual Environment for Reactor Applications (VERA) to address nuclear industry challenge problems such as crud-induced power shift (CIPS). The CTF thermal-hydraulic (T/H) subchannel code provides thermal feedback in the coupled neutronics, T/H, crud chemistry simulation that VERA performs. It has been discovered that the coarse meshing approach used by CTF (in which fuel rods are discretized into four azimuthal segments) can be a source of error in predicting crud growth and boron distribution in VERA CIPS calculations. Spacer grid effects lead to complex rod-to-fluid heat transfer behavior that, when not resolved, can lead to error in the prediction of crud growth and boron deposition. A higher-fidelity computational fluid dynamics approach can be used instead of CTF, but this leads to excessive simulation times. This paper presents an approach for using high-fidelity computational fluid dynamics data to create shape functions that are used in CTF to reconstruct rod surface heat transfer behavior as a function of spacer grid geometry. The approach is demonstrated for a 5 × 5 rod bundle facility with five mixing vane grids under a range of operating conditions encountered in nominal pressurized water reactor conditions. Furthermore, it is demonstrated that the grid heat transfer maps are successful at introducing a higher-fidelity heat transfer modeling capability into CTF.

CFD-informed↗

Full-scale hot cell test of an acoustic sensor dedicated to measurement of the internal gas pressure and composition of a LWR nuclear fuel rod

A full-scale hot cell test of the internal gas pressure and composition measurement by an acoustic sensor was carried on successfully between 2008 and 2010 on irradiated fuel rods in the LECA-STAR facility at Cadarache Centre. The acoustic sensor has been specially designed in order to provide a nondestructive technique to easily carry out the measurement of the internal gas pressure and gas composition of a LWR nuclear fuel rod. This sensor has been achieved in 2007 and is now covered by an international patent. The first positive result, concerning the device behaviour, is that the sensor-operating characteristics have not been altered by a two-year exposure in the hot cell ambient. We performed the gas characterisation contained in irradiated fuel rods. The acoustic method accuracy is now {+-}5 bars on the pressure measurement result and {+-}0.3% on the evaluated gas composition. The results of the acoustic method were compared to puncture results. Another significant conclusion is that the efficiency of the acoustic method is not altered by the irradiation time, and possible modification of the cladding properties. These results make it possible to demonstrate the feasibility of the technique on irradiated fuel rods. The transducer and the associated methodology are now operational. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Blocks and residual stresses in sapphire rods of different crystallographic orientations grown by the Stepanov method

The formation of blocks in shaped sapphire rods of two crystallographic orientations has been investigated. It is shown that, when growth occurs in the direction of the optical c axis, blocks are formed with a higher probability than in the case of growth in the a direction. A model of formation of blocks in rods of different orientations is proposed. The distribution of residual stresses over sapphire rod cross sections is measured by conoscopy. It is found that stresses increase from the middle of a rod to its periphery and reach 20 MPa.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Assessment of Existing Sierra/Fuego Capabilities Related to Grid-To-Rod-Fretting (GTRF)

The following report presents an assessment of existing capabilities in Sierra/Fuego applied to modeling several aspects of grid-to-rod-fretting (GTRF) including: fluid dynamics, heat transfer, and fluid-structure interaction. We compare the results of a number of Fuego simulations with relevant sources in the literature to evaluate the accuracy, efficiency, and robustness of using Fuego to model the aforementioned aspects. Comparisons between flow domains that include the full fuel rod length vs. a subsection of the domain near the spacer show that tremendous efficiency gains can be obtained by truncating the domain without loss of accuracy. Thermal analysis reveals the extent to which heat transfer from the fuel rods to the coolant is improved by the swirling flow created by the mixing vanes. Lastly, coupled fluid-structure interaction analysis shows that the vibrational modes of the fuel rods filter out high frequency turbulent pressure fluctuations. In general, these results allude to interesting phenomena for which further investigation could be quite fruitful.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗