Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RESIDUAL STRESSES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Effects of elevated temperature exposure on the residual stress state and microstructure of PVD Cr coatings on SiC investigated via in situ X-ray diffraction and transmission electron microscopy

Pure Cr coatings are being considered as corrosion-resistant layers for SiC-SiC f composite fuel cladding in light water reactors. The residual stress state and interdiffusion behavior of Cr coatings deposited on SiC substrates using bipolar high-power impulse magnetron sputtering (B-HiPIMS) and direct current impulse magnetron sputtering (DCMS) were studied using in situ X-ray diffraction experiments at 300 °C, 700 °C, and 1200 °C. After elevated temperature exposure, evolution of the coating microstructure and coating/substrate interdiffusion was characterized by transmission electron microscopy. The compressive residual stress of the dense B-HiPIMS coating at room temperature was gradually relieved at 300 °C, while the stress transitioned to a tensile state at 700 °C. Grain growth of the Cr coating and a Cr–SiC interdiffusion layer consisting of newly formed Cr–C and Cr–Si phases were observed in the B-HiPIMS coating after exposure at 700 °C. The phases in the interdiffusion layer were identified to be Cr 7 C 3 , Cr 3 Si, and Cr 5 Si 3 C x experimentally and by thermodynamic predictions. For the DCMS coating, however, changes in residual stress and microstructure at the elevated temperatures were limited by the inherent porosity and inhomogeneous structure of the as-deposited coating. At 1200 °C, both coating types interacted rapidly with the underlying SiC substrate in the early stages of the experiment. The results from this study suggest that the characteristics of the Cr coatings do not significantly change at the reactor operating temperature of 300 °C, while changes in microstructure and stress state are expected in off-normal conditions of 700 °C and 1200 °C. Finally the results from this study suggest the B-HiPIMS coating is best-suited as a protective coating for SiC fuel cladding.

36 MATERIALS SCIENCE↗
NASA NTRS1973

The effects of shot-peening residual stresses on the fracture and crack growth properties of D6AC steel

The fracture strength and cyclic crack-growth properties of surface-flawed, shot-peened D6AC steel plate were investigated. For short crack lengths (up to 1.5mm) simple linear elastic fracture mechanics - based only on applied loading - did not predict the fracture strengths. Also, Paris' Law for cyclic crack growth did not correlate the crack-growth behavior. To investigate the effect of shot-peening, additional fracture and crack-growth tests were performed on material which was precompressed to remove the residual stresses left by the shot-peening. Both tests and analysis show that the shot-peening residual stresses influence the fracture and crack-growth properties of the material. The analytical method of compensating for residual stresses and the fracture and cyclic crack-growth test results and predictions are presented.

Elber, W.↗
NASA NTRS1974

Effects of shot-peening residual stresses on the fracture and crack-growth properties of D6AC steel

The fracture strength and cyclic crack-growth properties of surface-flawed, shot-peened D6AC steel plate were investigated. For short crack lengths (up to 1.5 mm) simple linear elastic fracture mechanics - based only on applied loading - did not predict the fracture strengths. Also, Paris' Law for cyclic crack growth did not correlate the crack-growth behavior. To investigate the effect of shot-peening, additional fracture and crack-growth tests were performed on material which was precompressed to remove the residual stresses left by the shot-peening. Both tests and analysis show that shot-peening residual stresses influence the fracture and crack-growth properties of the material. This report presents the analytical method of compensating for residual stresses and the fracture and cyclic crack-growth test results and predictions.

Elber, W.↗
NASA NTRS1967

Ultrasonics used to measure residual stress

Ultrasonic method is used to measure residual stress in metal structures. By using this method, various forms of wave propagation in metals are possible, and more thorough analysis of complex geometric structures may be had.

Source record↗
NASA NTRS2024

Exploring the Role of Type-II Residual Stresses in A Laser Powder Bed Fusion Nickel-Based Superalloy Using Measurement and Modeling

Far-field high-energy X-ray diffraction microscopy (ff-HEDM) and the crystal plasticity finite element method (CPFEM) are used to investigate the role of grain-scale (Type-II) residual stresses on the fatigue life of additively manufactured (AM) Inconel alloy 625 (IN-625). Grain-averaged orientations, centroids, and residual elastic strain tensors from ff-HEDM data are used to instantiate a crystal plasticity model to simulate the effect of residual stresses at the grain scale. Simulation results indicate that the presence of tensile residual strains increase stress localization and heterogeneity within grains, triggering an earlier onset of plasticity. A microscale fatigue indicator parameter (FIP) is computed to model the impact of these residual strains on the cycles to fatigue crack nucleation. The crack nucleation model, based on the computed FIPs, predicts a significant reduction in the number of cycles for fatigue crack nucleation for mid- and high-cycle fatigue due to the residual strain induced localization, while the residual strains have minimal impact on low-cycle fatigue life.

Inconel↗
NASA NTRS2014

Bi-Metallic Composite Structures With Designed Internal Residual Stress Field

Shape memory alloys (SMA) have a unique ability to recover small amounts of plastic strain through a temperature induced phase change. For these materials, mechanical displacement can be accomplished by heating the structure to induce a phase change, through which some of the plastic strain previously introduced to the structure can be reversed. This paper introduces a concept whereby an SMA phase is incorporated into a conventional alloy matrix in a co-continuous reticulated arrangement forming a bi-metallic composite structure. Through memory activation of the mechanically constrained SMA phase, a controlled residual stress field is developed in the interior of the structure. The presented experimental data show that the memory activation of the SMA composite component significantly changes the residual stress distribution in the overall structure. Designing the structural arrangement of the two phases to produce a controlled residual stress field could be used to create structures that have much improved durability and damage tolerance properties.

Brice, Craig A.↗
NASA NTRS1973

Residual stress measurement and analysis using ultrasonic techniques.

A technique which utilizes ultrasonic radiation has been developed to measure residual stresses in metals. This technique makes it possible to detect and measure the magnitude of the principle stresses and also to obtain their direction. The velocities of ultrasonic waves in materials are measured as the time to travel a fixed path length, and the change in transit time is related to the applied stress. The linear relationship obtained allows a procedure based on this principle to be used for the measurement of residual stress using surface waves and shear waves. A method for plotting stress profiles through a material using surface waves uses varying frequencies for the ultrasonic wave. A limitation of the shear wave method is considered. The system used for this technique is called the Modified Time of Flight System.

Noronha, P. J.↗
NASA NTRS1987

Residual stress measurement in silicon sheet by shadow moire interferometry

A shadow moire interferometry technique has been developed to measure residual strain in thin silicon sheet. The curvature of a segment of sheet undergoing four-point bending is analyzed to include the applied bending moments, the in-plane residual stresses, and the 'end effect' of the sheet since it is of finite length. The technique is applied to obtain residual stress distributions for silicon sheet grown by the edge-defined film-fed growth technique.

Kwon, Y.↗
NASA NTRS1965

Residual stresses in 17-4 PH steel

Effects of heat treatment on residual stress of 17-4 PH steel, and influence of stress on dimensional integrity of strain gauge balances

STEEL↗
DOE OSTI2018

Prediction of residual stresses in a multipass pipe weld by a novel 3D finite element approach

Due to enormous computation cost, current residual stress simulation of multipass girth welds are mostly performed using two-dimensional (2D) axisymmetric models. The 2D model can only provide limited estimation on the residual stresses by assuming its axisymmetric distribution. In this study, a highly efficient thermal-mechanical finite element code for three-dimensional (3D) model has been developed based on high performance Graphics Processing Unit (GPU) computers. Our code is further accelerated by considering the unique physics associated with welding processes that are characterized by steep temperature gradient and a moving arc heat source. It is capable of modeling large-scale welding problems that cannot be easily handled by the existing commercial simulation tools. To demonstrate the accuracy and efficiency, our code was compared with a commercial software by simulating a 3D multi-pass girth weld model with over 1 million elements. Our code achieved comparable solution accuracy with respect to the commercial one but with over 100 times saving on computational cost. Moreover, the three-dimensional analysis demonstrated more realistic stress distribution that is not axisymmetric in hoop direction.

Huang, Hui↗
DOE OSTI2014

Effects of thermal cycling parameters on residual stresses in alumina scales of CoNiCrAlY and NiCoCrAlY bond coats

In this paper, furnace cycling experiments were performed on free-standing high-velocity oxygen-fuel bond coat samples to investigate the effect of material composition, surface texture, and cycling conditions on the average stresses in the formed oxide scales after cooling. The oxide scale thicknesses were determined by SEM image analyses and information about the stresses were acquired by photo-stimulated luminescence-spectroscopy. Additionally, the scale thickness dependent stress fields were calculated in finite-element analyses including approximation functions for the surface roughness derived on the basis of profilometry data. The evolution of the average residual stress as a function of oxide scale thickness was subject to stochastic fluctuations predominantly caused by local scale spallations. In comparison to the supplemental modeling results, thermal stresses due to mismatch of thermal expansion coefficients are identified as the main contribution to the residual stresses. Finally, the theoretical results emphasize that analyses of spectroscopic data acquired for average stress investigations of alumina scales rely on detailed information about microstructural features.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Role of Computational Parameters on Predicting Self-Consistent Residual Stress and Distortion during Wire Arc Additive Manufacturing

Production of three-dimensional metallic parts through integration of an articulated robot and gas metal arc welding, also known as wire arc additive manufacturing (WAAM), can produce large-scale components with moderate geometrical complexity. This technology is particularly appealing due to its high deposition rates, scalability, and cost-effective feedstock compared to other AM processes. Despite its advantages, WAAM adoption is hindered by challenges in ensuring geometric conformity without extensive distortion, defect-free structures, and consistent mechanical properties. Finite element analysis (FEA) is often used to address the challenge of geometrical conformity. As the size of parts increases, the best practices for mesh size and temporal resolution known in the literature become computationally unviable. This research examined the effects of mesh and time-step resolutions during transient FEA of a large-scale (248 layers) metallic part. The impact of computational parameters on the thermal history, displacement, and residual stress distributions were evaluated. The results showed that predicted distortion was consistent across resolutions, while time-step length significantly affected predicted thermal history, and mesh size influenced residual stress distributions. To investigate this relationship further, directionally biased meshes were considered and analyzed. The results indicated that increasing mesh resolution perpendicular to the welding path yielded stress predictions that aligned closely with higher-resolution models while offering substantial computational savings. In conclusion, the significances of this research are related to verification and validation of WAAM models for widespread industrial adoption and pragmatic guidelines for optimizing computation parameters for balancing computational efficiency and predictive accuracy of residual stress and distortion.

Solsbee, Brandon [Univ. of Tennessee, Knoxville, T↗
NASA NTRS1973

Combined effects of weld-induced residual stresses and flaws on the fracture strength of Ti-5Al-2.5Sn

The combined effects of weld-induced residual stresses and flaws on fracture strength were experimentally evaluated by testing Ti-5Al-2.5Sn surface flawed specimens at -320F (-195C) in liquid nitrogen. Flaws were located in weld metal with crack planes either parallel to or perpendicular to gas tungsten arc weld centerlines, and in base metal with the crack plane perpendicular to the rolling direction. Tests were conducted using two different flaw sizes to effect fracture stresses at two different levels including one level either at or near, and one level well below the tensile yield strength. Three different residual stress levels were generated, measured, and tested. Results were evaluated using modified linear elastic fracture mechanics theory.

Hall, L. R.↗
DOE OSTI2014

Estimation of uncertainty for contour method residual stress measurements

This paper describes a methodology for the estimation of measurement uncertainty for the contour method, where the contour method is an experimental technique for measuring a two-dimensional map of residual stress over a plane. Random error sources including the error arising from noise in displacement measurements and the smoothing of the displacement surfaces are accounted for in the uncertainty analysis. The output is a two-dimensional, spatially varying uncertainty estimate such that every point on the cross-section where residual stress is determined has a corresponding uncertainty value. Both numerical and physical experiments are reported, which are used to support the usefulness of the proposed uncertainty estimator. The uncertainty estimator shows the contour method to have larger uncertainty near the perimeter of the measurement plane. For the experiments, which were performed on a quenched aluminum bar with a cross section of 51 × 76 mm, the estimated uncertainty was approximately 5 MPa (σ/E = 7 · 10⁻⁵) over the majority of the cross-section, with localized areas of higher uncertainty, up to 10 MPa (σ/E = 14 · 10⁻⁵).

42 ENGINEERING↗
DOE OSTI2019

Measurement and prediction of through-section residual stresses in the manufacturing sequence of bearing components

Through-section residual stresses in an asymmetric, thin-walled tapered bearing component were non-destructively studied via neutron diffraction after soft machining, heat treatment and hard turning. Two-dimensional area maps revealed non-uniform distributions of stress fields in both the thinnest and thickest sections of the component, indicating that the entire processing sequence plays a vital role — not only in distortion, but in the final stress state as well. Here, a computational model was developed to further understand the extent of the distortion induced in bearing components as a result of process variables in the manufacturing sequence.

36 MATERIALS SCIENCE↗
NASA NTRS1998

Residual Stresses Modeled in Thermal Barrier Coatings

Thermal barrier coating (TBC) applications continue to increase as the need for greater engine efficiency in aircraft and land-based gas turbines increases. However, durability and reliability issues limit the benefits that can be derived from TBC's. A thorough understanding of the mechanisms that cause TBC failure is a key to increasing, as well as predicting, TBC durability. Oxidation of the bond coat has been repeatedly identified as one of the major factors affecting the durability of the ceramic top coat during service. However, the mechanisms by which oxidation facilitates TBC failure are poorly understood and require further characterization. In addition, researchers have suspected that other bond coat and top coat factors might influence TBC thermal fatigue life, both separately and through interactions with the mechanism of oxidation. These other factors include the bond coat coefficient of thermal expansion, the bond coat roughness, and the creep behavior of both the ceramic and bond coat layers. Although it is difficult to design an experiment to examine these factors unambiguously, it is possible to design a computer modeling "experiment" to examine the action and interaction of these factors, as well as to determine failure drivers for TBC's. Previous computer models have examined some of these factors separately to determine their effect on coating residual stresses, but none have examined all the factors concurrently. The purpose of this research, which was performed at DCT, Inc., in contract with the NASA Lewis Research Center, was to develop an inclusive finite element model to characterize the effects of oxidation on the residual stresses within the TBC system during thermal cycling as well as to examine the interaction of oxidation with the other factors affecting TBC life. The plasma sprayed, two-layer thermal barrier coating that was modeled incorporated a superalloy substrate, a NiCrAlY bond coat, and a ZrO2-8 wt % Y2O3 ceramic top coat. We examined the effect on stress during burner rig thermal cycling of the following independent variables: creep in the bond coat and top coat, oxidation, bond coat coefficient of thermal expansion, number of thermal cycles, and interfacial roughness. All these factors were suspected of influencing TBC failure. The model showed that all the material properties studied had a significant effect on the coating's residual stresses if the interface of the bond coat was rough. Bond coat expansion, bond coat oxidation, and bond coat creep had the highest effect on coating stresses, and these were highly interactive. The model also showed that the mechanism of stress generation during thermal cycling changed with the number of thermal cycles. Bond coat and top coat creep dominated stress generation during early thermal cycles, greatly increasing delamination stresses at the peaks of the bond coat. Therefore, creep is the prime driver for delamination cracking early in life, but cracking is limited to the bond coat peak region. Oxidation of the bond coat, on the other hand, tended to dominate stress generation during later cycles by greatly increasing delamination stresses over bond coat valleys. These results indicate that oxidation is the driver for the continued cracking necessary to cause ceramic layer spallation.

Freborg, A. M.↗