Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RADIATION PRESSURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Wisconsin In Situ Penning (WISP) gauge: A versatile neutral pressure gauge to measure partial pressures in strong magnetic fields

A new type of in-vessel Penning gauge, the Wisconsin In Situ Penning (WISP) gauge, has been developed and successfully operated in the Wendelstein 7-X (W7-X) island divertor baffle and vacuum vessel. The capacity of the quantitative measurements of the neutral reservoir for light impurities, in particular, helium, is important for tokamaks as well as stellarator divertors in order to avoid fuel dilution and radiative energy loss. Penning gauges assisted by spectroscopy are a powerful tool to obtain the total neutral pressure as well as fractional neutral pressures of specific impurities. The WISP gauge is a miniaturized Penning gauge arrangement, which exploits the ambient magnetic field of magnetic confinement fusion experiments to establish the Penning discharge. Then, in situ spectroscopy is conducted to separate the fractional neutral pressures of hydrogen, helium, and possibly also other impurities. The WISP probe head was qualified using the magnetic field of the Magnetized Dusty Plasma Experiment at Auburn University between 0.25 T and 3.5 T [E. Thomas et al ., J. Plasma Phys. 81, 345810206 (2015)]. The in-depth quantitative evaluation for hydrogen and helium will be shown as well as an exploration of nitrogen, argon, and neon. A power law scaling between current I and pressure p, I = f (Gas,V) p n⁽Gas, B⁾ , was shown. The factor f is gas and anode potential dependent, while n is gas and magnetic field strength dependent. Pressure measurements from 0.1 mbar and down to 1 × 10 -5 mbar were achieved, demonstrating a reliable operating range for relevant pressure levels in the divertor and main vessel regions in current and future fusion devices, with a time resolution of up to 1 kHz. The lowest achievable pressure measurement increases with an increase in B and can be shifted with the anode potential V . At W7-X, the WISP probe head was mounted on an immersion tube setup that passes through the cryostat and places the probe head close to the plasma. Two probe heads were positioned in different divertor pump gaps, top and bottom, and one close to the plasma on the midplane in one module. The gauges were in situ calibrated together with the ASDEX pressure gauges [G. Haas and H.-S. Bosch, Vacuum 51, 39 (1998)]. Data were taken during the entire operation phase 1.2b, and measurements were coherent with other neutral gas pressure gauges. For the spectroscopic partial pressure measurements, channels of a spectroscopic detection system based on photo-multipliers, a so-called filterscope [R. J. Colchin et al ., Rev. Sci. Instrum. 74, 2068 (2003)], provided by the Oak Ridge National Lab were used.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Laser pulse-length dependent ablation and shock generation in silicon at 5 × 10 14 W/ cm 2 intensities

The effect of laser pulse duration on energy coupling into a planar silicon target is investigated in experiments at the OMEGA-EP facility by varying the laser pulse length τ —spanning 3 orders of magnitude from 100 ps to 10 ns—while maintaining a constant peak laser intensity, I 0 = 5 × 10 14 W/ cm 2 . In theoretical models, the ablation pressure primarily scales for a given material with laser intensity and wavelength, which are all fixed variables here, allowing us to explore the specific role of laser pulse duration. Two-dimensional radiation-hydrodynamics simulations benchmarked with optical probing of the expanding plasma show that the pulse duration is critical for the ablation pressure to reach a steady state. Moreover, the pulse duration impacts shock decay and multiple wave effects, which strongly dictate the evolving shock profile that propagates within the laser-shocked target as ultimately measured by rear-surface diagnostics. The shock velocities inferred from the theoretical model, after considering shock decay, impedance matching, and shock Hugoniot, are found to be in good agreement with velocimetry measurements. However, discrepancies are observed with simulations for the shorter (0.1 ns) and longer (10 ns) pulse durations, which are respectively attributed to unaccounted contributions of kinetic absorption mechanisms and instabilities in simulations. Published by the American Physical Society 2024

Bailly-Grandvaux, M. (ORCID:0000000175294013)↗
DOE OSTI2023

Laser material interactions in tamped materials on picosecond time scales in aluminum

Here, a 100 ps laser is used to probe the pressure generation, depth of the non-solid ablator, and the non-linear optical effects through tamper materials. Samples consisted of an aluminum ablator with tampers of sapphire and coverslip glass. In general, the sapphire tamped sample achieves higher pressures at lower laser intensities as compared to the coverslip glass tamped sample. Attempts to model the details of this set of experimental data with standard available radiation coupled hydrodynamic codes make clear that more physics is needed in these simulations to accurately predict the impact of the tamper material on the pressure generation and the depth of non-solid aluminum.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Microwave-driven heterogeneous catalysis for activation of dinitrogen to ammonia under atmospheric pressure

This paper presents an innovative approach to producing energy-dense, carbon–neutral liquid ammonia as a means for carrying energy. This approach synergistically integrates microwave reaction chemistry with novel heterogeneous catalysis that decouples dinitrogen activation from high-temperature and high-pressure reactions, altering reaction pathways and increasing ammonia formation rate. Results presented here demonstrate that ammonia synthesis can be conducted at 280 ? and ambient pressure to achieve ~1 mmol ammonia/g cat/h over supported ruthenium catalyst systems utilizing microwave irradiation. It is further shown that adding promoter ions such as potassium, cerium, and barium significantly improves the ammonia production rate over undoped ruthenium-based catalysts. This effect could be attributed to enhanced dielectric loss processes that lead to stronger microwave absorption by the catalyst. Measurement of the equilibrium constant under microwave conditions showed a higher ammonia yield than under thermal equilibrium conditions for both the iron- and ruthenium-based catalysts. Finally, this study also illustrates the advantages of using a variable-frequency microwave reactor for ambient-pressure ammonia synthesis. Mechanistically, investigators believed that the oscillating electric fields of the radiation can couple with adsorbed nitrogen on the surface and accelerate its dissociation. Since dinitrogen dissociation on the surface is rate limiting, this effectively accelerates the reaction.

Hu, Jianli (John)↗
DOE OSTI2021

Experimental Observations of Laser-Driven Tin Ejecta Microjet Interactions

The study of high-velocity particle-laden flow interactions is of importance for the understanding of a wide range of natural phenomena, ranging from planetary formation to cloud interactions. Experimental observations of particle dynamics are sparse given the difficulty of generating high-velocity flows of many particles. Ejecta microjets are micron-scale jets formed by strong shocks interacting with imprinted surfaces to generate particle plumes traveling at several kilometers per second. As such, the interaction of two ejecta microjets provides a novel experimental methodology to study interacting particle streams. In this Letter, we report the first time sequences of x-ray radiography images of two interacting tin ejecta microjets taken on a platform designed for the OMEGA Extended Performance (OMEGA EP) laser. We observe that the microjets pass through each other unattenuated for the case of 11.7±3.2 GPa shock pressures and jet velocities of 2.2±0.5 km/s but show strong interaction dynamics for 116.0±6.1 GPa shock pressures and jet velocities of 6.5±0.5 km/s. Furthermore, we find that radiation-hydrodynamic simulations of the experiments are able to capture many aspects of the collisional behavior, such as the attenuation of jet velocity in the direction of propagation, but are unable to match the full spread of the strongly interacting cloud.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Modeling In-Reactor Temperature Gradients in Lithium Aluminate Ceramic Pellets

In reactor thermal performance of lithium aluminate ceramic pellets are calculated to determine operating temperatures if internal components shift during irradiation. A 2D conduction model was setup to model this scenario with additional physics, including thermal expansion of components to reactor temperatures, creep down of the cladding due to differential pressure between the inside of the rod and reactor coolant system, and net radiation exchange between components. The non-linear coupling of the governing equations presented convergence challenges due to the very different effects from a small temperature change on the radiation vs radial and circumferential conduction equations. Initial temperature guesses for the multidimensional solution were provided from conservative 1D models simulating bounding scenarios. Convergence was greatly improved by taking small steps towards the root solutions and averaging with initial guesses. The final method robustly converged all 132 points at an axial plane after a few dozen iterations. The temperature results show that the additional physics have a secondary effect as the dominant heat transfer mechanism is radial conduction across the gas gap followed by circumferential conduction around components. Circumferential conduction in the lithium aluminate pellets is enhanced by the relatively high thermal conductivity of this ceramic.

Carstens, Nathan A.↗
DOE OSTI2024

An analysis of parameters affecting ampacity in aircraft bipolar MVDC power cables via coupled electrical, thermal, and computational fluid dynamic modelling

Abstract The next generation of aircraft, including more electric aircraft and all‐electric aircraft (AEA), requires electric power systems with high power density and low system mass specifications. Increasing the voltage of the system to the range of a few kV, medium voltage (MV), is a reasonable approach to achieving high‐power‐density and low‐system‐mass EPSs for aircraft applications. Higher voltages, however, pose many challenges for aviation MV power cables such as arcs and arc tracking, partial discharges (PDs), and thermal management. In this regard, thermal management is more challenging since heat transfer by convection is greatly reduced at wide‐body aircraft's cruising altitudes due to the reduced air pressure. In this paper, a finite element method (FEM) model is developed in COMSOL Multiphysics for an aircraft bipolar MVDC (±5 kV) power cable. Using the model, the maximum permissible cable current at a low pressure of 18.8 kPa (at an altitude of 12.2 km from sea level, the usual cruising altitude for wide‐body aircraft) is calculated. Also, an analytical model is developed based on analytical and proven empirical correlations governing conductive, radiative, and convective heat transfers at the steady state to estimate the ampacity of the bipolar cable system at reduced pressure. It was shown that the proposed analytical model can be used for atmospheric pressure and systems with a larger number of poles, expanding its range of applications. The results of the FEM and analytical models correlate at wide ranges of parameters such as ambient temperature, duct size, distance between the positive and negative pole cables, and the overall diameter of the cables. The influence of horizontal and vertical arrangement of poles is included in the analytical model. The results of this study can be used to design bipolar MVDC power cable systems for the envisaged wide‐body AEA.

Azizi, Arian↗
DOE OSTI2020

Effects of initial conditions and transport on ram pressure, Mach number, and uniformity for plasma liner formation and implosion

Plasma jet driven magneto-inertial fusion involves the merging of high Mach number plasma jets in a spherically converging geometry to form an imploding plasma liner. A three-dimensional smooth particle hydrodynamic simulation tool was used to study the number of plasma jets, jet density, and implosion velocity on the effects of formation and subsequent implosion of a plasma liner. The effects of different transport physics are presented. Thermal radiation and two-temperature modeling were found to have the most significant impact on the ram pressure. Solid angle averaged ram pressure and Mach number degradation were of particular interest in this study. Higher jet numbers were found to result in higher peak ram pressure. A spherical harmonic analysis was conducted for each case, providing a quantitative measure of the non-uniformity of the liner during the implosion process and how non-uniformities are affected by the different parameters explored in this study.

Schillo, Kevin↗
DOE OSTI2020

Experimental study for critical heat flux in 2x2 rod bundles at high pressure conditions

Critical heat flux (CHF) phenomena has been a topic of study for over fifty years yet remains a serious concern across industries and especially in water-cooled nuclear reactor design. CHF data in the high-pressure range is limited, and the effects of bundle geometry and non-uniform heat flux profile are challenging to quantify. In this study, CHF experiments were performed in upward flowing water in a 2 × 2 rod bundle with a cosine profile heat flux. Data were collected between 16.5 and 18 MPa at two mass flux conditions with three inlet subcooling conditions. Under these conditions, average CHF was shown to decrease with increasing pressure. However, pressure had less of an effect than decreasing the inlet subcooling or the mass flux, both of which reduce the CHF value considerably. Of interest, correlations that have been developed for lower pressure continued to predict CHF occurrences with moderate accuracy outside their ranges of validity. Nearly all predicted values were within 20% of experimental values.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2019

Eddy Flux and Meteorology over Deciduous Forest, Prairie, and Soybean Ecosystems in Missouri, USA, during the Total Solar Eclipse of 2017

Eddy fluxes and meteorology data are reported at high temporal resolution for three flux tower sites in Mid-Missouri before, during, and after the Total Solar Eclipse of August 21, 2017. Mid-Missouri experienced up to 2 minutes and 40 seconds of totality at around solar noon during the eclipse (Fig. 1). The sites are located in deciduous oak-hickory forest, native prairie, and soybean ecosystems (Table 1 and Fig. 3). Eddy fluxes were computed using a wavelet-based approach that permitted the calculation of two-minute mean fluxes without losing low frequency flux contributions (Fig. 2). During the eclipse, standard meteorological variables were sampled and recorded at 5 second intervals. The two-minute means of fluxes and meteorology are reported. This data product includes three data files in NetCDF (*.nc) format, three data dictionary files and a file-level metadata file in comma separate (*.csv) format, and a user guide in PDF (*.pdf) format.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Burning plasma achieved in inertial fusion

Obtaining a burning plasma is a critical step towards self-sustaining fusion energy. A burning plasma is one in which the fusion reactions themselves are the primary source of heating in the plasma, which is necessary to sustain and propagate the burn, enabling high energy gain. After decades of fusion research, here we achieve a burning-plasma state in the laboratory. These experiments were conducted at the US National Ignition Facility, a laser facility delivering up to 1.9 megajoules of energy in pulses with peak powers up to 500 terawatts. We use the lasers to generate X-rays in a radiation cavity to indirectly drive a fuel-containing capsule via the X-ray ablation pressure, which results in the implosion process compressing and heating the fuel via mechanical work. The burning-plasma state was created using a strategy to increase the spatial scale of the capsule through two different implosion concepts. These experiments show fusion self-heating in excess of the mechanical work injected into the implosions, satisfying several burning-plasma metrics. Additionally, we describe a subset of experiments that appear to have crossed the static self-heating boundary, where fusion heating surpasses the energy losses from radiation and conduction. These results provide an opportunity to study α-particle-dominated plasmas and burning-plasma physics in the laboratory.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Comparative analysis of characteristics of a supersonic cw chemical HF laser on molecular fluorine and nitrogen trifluoride

We have experimentally studied the characteristics of a supersonic cw chemical HF laser with a flat nozzle array based on a nozzle – nozzle reagent mixing scheme operating with the use of F{sub 2} – D{sub 2} – He and NF{sub 3} – D{sub 2} – He fuel compositions in an atomic fluorine generator. The active medium flow field pattern, its gas-dynamic characteristics, and the laser radiation spectrum are considered. The comparison of these characteristics has made it possible to establish a strong impact on the flow field (lasing zone length) of the chemical composition of the combustion products from the atomic fluorine generator. The gas-dynamic parameters of the active medium formed by using a NF{sub 3} – D{sub 2} – He fuel have turned out to be less acceptable in terms of the gas flow pressure recovery than in the case of F{sub 2} – D{sub 2} – He fuel, while the radiation spectrum was more preferable from the viewpoint of passing through the atmosphere. (paper)

36 MATERIALS SCIENCE↗
DOE OSTI2025

Sound velocities and thermal equation of state of fcc -iron-nickel alloys at high pressure and high temperature: Implications for the cores of Moon and several planets

Fcc-Fe-Ni alloy is believed to be the most dominant solid constitute of moderate-sized terrestrial planetary cores. Investigating the physical properties, especially the density and sound velocity of Fe-Ni alloys and comparing them with seismic observations is an indispensable approach to constructing compositional models for planetary interiors. In this study, we conducted sound velocity measurements on Fe-Ni alloys with 10 wt.% and 20 wt.% Ni up to ∼13.5 GPa and 1073 K, using the ultrasonic interferometry technique in a multi-anvil apparatus in conjunction with synchrotron radiation. By fitting the experimental data to finite strain equations, the bulk and shear moduli and their pressure and temperature derivatives are derived, yielding K S0 =145.8(14) GPa, G 0 = 73.2(7) GPa, K S0 ’ = 5.89(24), G 0 ’ = 2.89(8), (∂K S /∂T) P = -0.0181(12) GPa/K and (∂G/∂T) P = -0.0393(10) GPa/K for fcc-Fe 80 Ni 20 . An examination of the density-velocity relationship shows that compressional wave velocity is insensitive to temperature within the current pressure and temperature range, while shear wave velocity exhibits a large reduction with increasing temperature. Here, extrapolation of the sound velocities following the finite strain theories suggests that much slower Vs should be expected at pressure and temperature conditions corresponding to those of the lunar core. Possible core density and velocity profiles for other moderate planets and satellites, such as Mars, Mercury, and Ganymede are also calculated.

Equation of state↗
DOE OSTI2020

Role of opacity at the 9 keV back lighter energy used in measuring the equation of state of boron at pressures up to a Gbar

Many experiments have been conducted at the National Ignition Facility to measure the equation of state Hugoniot of plastic, boron, and diamond at extreme pressures up to a Gbar. The “Gbar” design employs a strong spherically converging shock launched through a solid ball of material using a hohlraum radiation drive. The shock front conditions are characterized using X-ray radiography, typically at energies near 9 keV. Here we examine how the opacity of boron at 9 keV changes at high pressures and temperatures. Understanding this is vital to unfolding the density in the shock front as pressures exceed 100 Mbar. We compare opacity calculations from a number of methods including the legacy XSN opacity tables, super transition array (STA), average atom (AVAT), and detailed configuration accounting (DCA) methods. We examine how the changing opacity is correlated with the K-shell occupation calculated using the opacity methods as well as other electronic structure methods such as MECCA, Purgatorio, and an all-electron Kohn-Sham density functional theory calculation that uses optimized all-electron norm-conserving Vanderbilt pseudopotentials (ONCV). We also examine the relative contribution of free-free opacity to the overall opacity, which is dominated by bound-free absorption.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2021

Data reduction considerations for spherical R-32(CH 2 F 2 )-air flame experiments

The burning velocities of mixtures of refrigerant R-32 (CH 2 F 2 ) with air over a range of equivalence ratios are studied via shadowgraph images of spherically expanding flames (SEFs) in a large, optically accessible spherical chamber at constant pressure. Numerical simulations of the 1-D, unsteady, spherical flames incorporating an optically thin radiation model and detailed kinetics accurately predict experimental results for a range of equivalence ratios. For these low burning velocity flames, the effects of stretch and radiation occur simultaneously and make extraction of the unstretched burning velocity from the experimental data difficult. Different data reduction approaches are shown to have large effects on the burning velocities inferred from the experiments and simulations. A new flame radius tracking approach for the experimental images is shown to provide improved agreement of the burned gas velocity variation with stretch predicted by the simulations and helps to compensate for mild flame distortion due to buoyancy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Reduced photothermal heating in diamonds enriched with H3 point defects

Solid-state laser refrigeration of semiconductors remains an outstanding experimental challenge. In this work, we show that, following excitation with a laser wavelength of 532 nm, bulk diamond crystals doped with H3 centers both emit efficient up-conversion (anti-Stokes) photoluminescence and also show significantly reduced photothermal heating relative to crystals doped with nitrogen–vacancy (NV) centers. The H3 center in diamond is a highly photostable defect that avoids bleaching at high laser irradiances of 10–70 MW/cm 2 and has been shown to exhibit laser action, tunable over the visible band of 500–600 nm. Here, the observed reduction of photothermal heating arises due to a decrease in the concentration of absorbing point defects, including NV-centers. These results encourage future exploration of techniques for H3 enrichment in diamonds under high-pressure, high-temperature conditions for the simultaneous anti-Stokes fluorescence cooling and radiation balanced lasing in semiconductor materials. Reducing photothermal heating in diamond through the formation of H3 centers also opens up new possibilities in quantum sensing via optically detected magnetic resonance spectroscopy at ambient conditions.

42 ENGINEERING↗
DOE OSTI2021

VERA-Grizzly Ex-Core Calculations: Watts Bar Unit 1 Cycles 1-2

The critical structures that comprise light-water reactor (LWR) nuclear power plants are subjected to operating environments that can challenge their integrity. Structures in close proximity to the reactor core, such as the reactor pressure vessel (RPV) and the biological shield wall, are subjected to high levels of radiation emanating from the core, as well as elevated temperatures. As the US fleet of operating LWRs ages, the effects of these operating environments on the integrity of these structures must be considered to ensure their continued safe operation. Extending the lifetime of commercial reactors and maintaining the aging reactor fleet require accurate prediction of the exposure of ex-core components to neutron and photon radiation. In particular, concrete degradation studies must be performed to evaluate the safety and long-term operation of reactors with lifetime extensions. The concrete reactor bioshield is important for providing radiological protection during operation and must last for the entire lifetime of the reactor. Recent interest in lifetime extensions furthers the need to accurately simulate concrete material degradation in the reactor bioshield. As a result of this need, the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program has funded this study to couple its tools, Virtual Environment for Reactor Applications (VERA) and Grizzly. VERA allows users to set up models to calculate time-dependent and fully coupled solutions (with thermal feedback) for ex-core quantities of interest such as vessel and coupon fluence and detector responses for multiple statepoints and cycles. Grizzly is a finite-element application based on the Multiphysics Object Oriented Simulation Environment (MOOSE) framework that is used to enable aging materials calculations. This report highlights the work performed to calculate the fluence in the vessel and concrete for Watts Bar Nuclear Plant Unit 1 (WBN1) Cycles 1 and 2. The fluences obtained from VERA were successfully transferred to Grizzly using a Python script. Four simulations were run with Grizzly: (1) the Mazars model with the initial Young’s modulus being the instantaneous modulus, (2) the Mazars model with the initial Young’s modulus being the delayed modulus, (3) the Mazars model with the initial Young’s modulus being the delayed modulus with the addition of the effects of micro-damage caused by irradiation, and (4) the Mazars model with the initial Young’s modulus being the instantaneous modulus, and with the addition of micro-damage and creep. Details regarding the methods used to obtain the fluence and the statistical errors associated with the VERA Monte Carlo Shift calculations are discussed in greater detail in this report. The results obtained from the four Grizzly models are also presented in this report.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2024

Atmospheric Ion Composition, SGP, April-May 2023

These files contain select ion count rates measured by an atmospheric pressure interface time-of-flight mass spectrometer (APi-ToF) at the Atmospheric Radiation Measurement Southern Great Plains site from April 28, 2023 to May 31, 2023. Files are in ICARTT format. The APi-ToF measures the chemical composition of naturally charged ions using mass spectrometry. Due to the nature of the measurements, time-series data are non-quantitative. This dataset contains time-series information for the ions that are typically the most intense ions observed.

54 ENVIRONMENTAL SCIENCES↗