Quenching of vacancies into molybdenum
Helium 2 quenching environment, rate, and impurity effects on quenching of vacancies into body centered cubic molybdenum
Gotsky, E. R.↗
SEARCH · Engineering Papers
Results for “QUENCHING”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Microstructure and mechanical properties of quenched and tempered 300M steel
Type 300M steel, which is being used for the landing gear on the space shuttle orbiter, was subjected to a wide range of quenched and tempered heat treatments. The plane-strain fracture toughness and the tensile ultimate and yield strengths were evaluated. Cryogenic mechanical properties were obtained for conventionally heat-treated steel. The microstructure of all heat-treated test coupons was studied both optically and by transmission electron microscopy. Fracture surfaces were studied by means of scanning electron microscopy. Results indicate that substantial improvement in toughness with no loss in strength can be accomplished in quenched and tempered steel by austenitizing at 1255 K or higher. Low fracture toughness in conventionally austenitized 300M steel (1144 K) appears to be caused by undissolved precipitates, seen both in the submicrostructure and on the fracture surface, which promote failure by quasi-cleavage. The precipitates appeared to dissolve in the range 1200 to 1255 K.
Youngblood, J. L.↗
Photochemistry of bromoacetylene - Formation of HBr and quenching of excited Br/4 2P 0 1/2/
The photolysis of bromacetylene is examined by means of vacuum ultraviolet flash photolysis-kinetic spectroscopy, with attention given to the production of Br atoms in the 2P 0 3/2 and 2P 0 1/2 states, the production of HBr, and UV absorption attributable to the ethynyl radical. Although Br(2P 0 1/2) and Br(2P 0 3/2) were both directly observed at the shortest delay time after the flash, strongly indicating the presence of the ethynyl radical, transient absorption by C2H was not detected in the range 125 to 180 nm. Quenching rate constants for the decay of the 2P 0 1/2 state of Br, which is observed to form concurrently with the ground state, are derived for quenching by He, CH2Br, CF4, and D2 from the pseudo-first-order decay rates. HBr was observed as a secondary photolysis product, and a model of its formation by the exothermic reaction of ground-state atoms with C2HBR, coupled with the secondary production of Br atoms, is found to agree well with the experiment.
Laufer, A. H.↗
I/asterisk/ /6s 4P/ collisional quenching - Application to the IF 491-nm laser
Measurements of the rate constants for quenching of the excited I (6s 4P) states by Ar, Xe, CF39I, UF6, and NF3 are described. Each rate constant is determined by recording the exponential time decay of the excited IF or excited I2 (342 nm) fluorescence in the afterglow of the e-beam-excited plasmas containing Ar, CF3I, NF3, and the desired quenching gas. In addition, further experimental evidence in support of neutral channel formation of excited IF in e-beam-pumped Ar/CF3I/NF3 mixtures is presented. Details of the experimental apparatus and gas handling procedures are given, and the kinetics model developed to interpret the experimental data is described.
Hutchison, S. B.↗
The influence of containerless undercooling and rapid solid-state quenching on the superconductive and magnetic properties of some clustering alloy systems
The properties of clustering alloy systems and the manner in which they are influenced by rapid quenching from a containerless undercooled melt are discussed. It was postulated that rapid quenching under such conditions would result in highly disordered metastable alloys, and furthermore, that alloys in such conditions would possess physical properties characteristically different from those of alloys in the annealed equilibrium state. The scope of the program is essentially to gauge the influence of containerless undercooling on the submicrostructure of clustering-type alloys, using certain physical properties as diagnostic tools. Microstructures and macrostructures were to be examined using optical- and scanning-electron microscopy.
Collings, E. W.↗
Rotational-level-dependent quenching of A2Sigma(+) OH and OD
The role of rotation in the collisional quenching of the A2Sigma(+) v' = 0 states of OH and OD is investigated experimentally by laser-induced-fluorescence measurements in a two-chamber differentially pumped flow chamber similar to that of McDermid and Laudenslager (1982). The experimental apparatus is described in detail, and the results are presented in extensive tables and graphs. Collisional-quenching rate constants are determined for 21 different quenchers at various specific N' rotational levels and shown to decrease as the rotational quantum number increases, with no significant role for the internal levels of the colliding pairs and reasonable agreement with theoretical calculations incorporating attractive forces.
Copeland, R. A.↗
Thermal electron quenching of N(2D) - Consequences for the ionospheric photoelectron flux and the thermal electron temperature
This paper examines the effects of quenching of N(2D) by thermal electrons on the ionospheric photoelectron flux and on the thermal electron heating rate. It is shown that the 2.5 eV electrons produced by electron quenching of N(2D) can account for the differences between theoretical and experimental 0-3 eV photoelectron fluxes above 200 km altitude. In addition, the heat transferred to the thermal electron gas amounts to 70 percent of the photoelectron local heating rate at 250 km altitude. The effect of the extra heating is to increase the electron temperature by approximately 200 K at 250 km.
Richards, P. G.↗
Statistical study of thermal fracture of ceramic materials in the water quench test
The Weibull statistical theory of fracture was applied to thermal shock of ceramics in the water quench test. Transient thermal stresses and probability of failure were calculated for a cylindrical specimen cooled by convection. The convective heat transfer coefficient was calibrated using the time to failure which was measured with an acoustic emission technique. Theoretical failure probability distributions as a function of time and quench temperature compare favorably with experimental results for three high-alumina ceramics and a glass.
Rogers, Wayne P.↗
Quench gases for xenon- (and krypton-) filled proportional counters
Xenon-filled proportional counters are used extensively in astronomy, particularly in the hard X-ray region. The choice of quench gas can have a significant effect on the operating characteristics of the instrument although the data necessary to make the choice are not easily obtainable. Results which detail the performance obtained from both cylindrical and parallel field geometries for a wide variety of readily available, ultrahigh or research grade purity, quench gases are presented.
Ramsey, B. D.↗
Molten (Mg0.88Fe0.12)2SiO4 at lower mantle conditions - Melting products and structure of quenched glasses
Infrared spectra of quenched magnesium silicate glasses synthesized by fusing olivine at pressures in excess of 50 GPa and temperatures greater than 2500 K demonstrate that silicon is dominantly present in four-fold coordination with respect to oxygen within these quenched glasses. This low coordination is attributed, by analogy with the structural behavior of glasses compressed at 300 K, to the instability of higher coordinations in glasses of these compositions on decompression. Spectra of glasses formed in a hydrous environment document that water is extensively soluble in melts at these high pressures and temperatures. Also, these results are consistent with the melting of (Mg0.88Fe0.12)2SiO4 compositions to liquids near pyroxene in stoichiometry under these conditions, with iron-rich magnesiowuestite being the liquidus phase.
Williams, Quentin↗
Collisional quenching of O(1D) by O(3P)
Metastable O(1D) atoms may be quenched in collisions with ground state O(3P) atoms by transitions in the avoided crossing regions of the three lowest 3Pi(g) states of O2 of which the lowest separates to O(3P) + O(3P) and the two upper to O(3P) + O(1D). Quantal calculations of the adiabatic potential energy curves of the 3Pi(g) states are carried out with particular attention to an avoided crossing region in the lowest two states around a nuclear separation of 3.2a(0). Diabatic potential matrix elements are constructed from the adiabatic curves by imposing the requirement that they be smooth everywhere. A multi-state diabatic formulation is used to describe the scattering and the cross-sections for the collision-induced quenching of O(1D) atoms are calculated.
Yee, J.-H.↗
Splat-quench solidification of freely falling liquid-metal drops by impact on a planar substrate
Results are presented of a study of the splat-quench solidification of small, freely falling liquid drops of the alloy Nitronic 40W, which were allowed to impact on a solid, planar, horizontal substrate. The principal variable was the substrate material, with substrates of copper, alumina and fused quartz being used. The shapes of the solidified splats were correlated with a simplified model for the energetics of the splatting process and with the thermal conductivity of the substrate. The measured results are qualitatively in agreement with theoretical predictions, and suggestions are offered for a more comprehensive model of splat-quench solidification. A relationship between sessile droplet diameter and parent wire diameter is also presented and discussed.
Collings, E. W.↗
Microstructure and magnetization of Y-Ba-Cu-O prepared by melt quenching, partial melting and doping
Y-Ba-Cu-O samples prepared by means of a variety of melt-based techniques exhibit high values for their magnetic properties compared with those of samples prepared by solid state sintering. These techniques include single-stage partial melting as well as melt quenching followed by a second heat treatment stage, and they have been applied to the stoichiometric 123 composition as well as to formulations containing excess yttrium or other dopants. The structure of these melt-based samples is highly aligned, and the magnetization readings exhibit large anisotropy. At 77 K and magnetic field intensities of about 2 kOe, diamagnetic susceptibilities as high as -14 x 10(exp -3) emu/g were obtained in the cases of melt-quenched samples and remanent magnetization values as high as 10 emu/g for samples prepared by partial melting.
Hojaji, Hamid↗
Analysis of X-Ray Microradiographs of Al-Au Interface Quench Profile using Modeling of Solidification Including Double-Diffusion and Convection in the Melt
Experimental data on Al-0.8Au horizontal solidification of a 1 mm thick specimen in a BN crucible shows the effect of growth rate on the solidification interface shape. For translation rates below 0.5 micron/s the interface maintains a plain and flat shape. When the translation rate is 3 to 5 micron/s or more, the interface appearance changes to two planar zones, with the zone closer to the bottom having higher inclination. The interface shapes were measured by first quenching in place during growth. X-ray microscopy shows the interface shape within the quenched sample by viewing through the side of the specimen. In order to provide theoretical explanation of the phenomena, numerical modeling was undertaken using finite element code FIDAP. Double diffusion convection in Al-0.8Au melt and crystal-melt interface curvature during directional solidification was analyzed numerically. Actual thermophysical properties of Al-0.8Au including the binary Al-Au phase diagram were used. Although convection in the sample is weak, for the slower translation rate convection and diffusion is sufficient for the redistribution of initial compositional stratification caused by gravity. When translation rate is raised, neither convection nor diffusion can provide proper mixing so that solidification temperatures differ significantly near the bottom within the bulk of the sample. As a result, the solid-liquid interface appears to have two planar zones with different inclination.
Bune, Andris V.↗
Quench Module Insert (QMI) and the Diffusion Module Insert (DMI) Furnace Development
The Quench Module Insert (QMI) and the Diffusion Module Insert (DMI) are microgravity furnaces under development at Marshall Space Flight Center. The furnaces are being developed for the first Materials Science Research Rack (MSRR-1) of the Materials Science Research Facility (MSRF), one of the first International Space Station (ISS) scientific payloads. QMI is a Bridgman furnace with quench capability for studying interface behavior during directional solidification of metallic and alloy materials. DMI will be a Bridgman-Stockbarger furnace to study diffusion processes in semiconductors. The design for each insert, both QMI and DMI, is driven by specific science, operations and safety requirements, as well as by constraints arising from resource limitations, such as volume, mass and power. Preliminary QMI analysis and testing indicates that the design meets these requirements.
Crouch, Myscha R.↗
Efficient Quenching of Population Trapping in Excited Yb(+)
We report on a study to determine the efficiency of various buffer gases in quenching the population trapping states of laser-excited ytterbium ions. The ions were confined in an rf-dc hybrid trap, and their (2)S(.5) left and right arrow (2)P(3/2) transition was excited with 329-nm laser light. Buffer gases used include H2, N2, CO2, Ar, and He at several different pressure regimes. We have identified N2 to be highly efficient in quenching the population of the trapping states and thus be the most suitable buffer gas to use with ytterbium for the development of a trapped-ion microwave frequency standard.
Seidel, D. J.↗
Quench Module Insert (QMI) and the Diffusion Module Insert (DMI) Furnace Development
This paper presents, in viewgraph form, QMI (Quench Module Insert) and DMI (Diffusion Module Insert) furnace development. The topics include: 1) Furnace Module in Rack; 2) Quench Module Insert; 3) QMI in MSL Core; 4) Diffusion Module Insert; 5) QMI; and 6) QMI Development and Testing.
Crouch, Myscha↗
Quenching of Particle-Gas Combustible Mixtures Using Electric Particulate Suspension (EPS) and Dispersion Methods
A cooperative study is being carried out between Iowa State University and McGill University. The new study concerns wall and particle quenching effects in particle-gas mixtures. The primary objective is to measure and interpret flame quenching distances, flammability limits, and burning velocities in particulate suspensions. A secondary objective is to measure particle slip velocities and particle velocity distribution as these influence flame propagation. Two suspension techniques will be utilized and compared: (1) electric particle suspension/EPS; and (2) flow dispersion. Microgravity tests will permit testing of larger particles and higher and more uniform dust concentrations than is possible in normal gravity.
Colver, Gerald M.↗