Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Parametric systems”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Analysis of a longitudinal pilot-induced oscillation experienced on the approach and landing test of the space shuttle

During the final free flight (FF-5) of the shuttle's approach and landing tests, the vehicle experienced pilot-induced oscillations near touchdown. The light test data showed that pilot inputs to the hand controller reached peak-to-peak amplitudes of 20 deg at a frequency between 3 and 3.5 radians per second. The controller inputs were sufficient to exceed the priority rate limit set in the pitch axis. A nonlinear analytical study was conducted to investigate the combined effects of pilot input, rate limiting, and time delays. The frequency response of the total system is presented parametrically as a function of the three variables. In general, with no dead time, for controller inputs of 5 deg or less, the total system behaves in a linear fashion. For 10 deg of controller input, independent of the delay time, the elevon loop will be rate saturated above a frequency of 4 radians per second.

Smith, J. W.↗
NASA NTRS1992

Dynamic analysis of Free-Piston Stirling Engine/Linear Alternator-load system-experimentally validated

This paper discusses the effects of variations in system parameters on the dynamic behavior of the Free-Piston Stirling Engine/Linear Alternator (FPSE/LA)-load system. The mathematical formulations incorporate both the mechanical and thermodynamic properties of the FPSE, as well as the electrical equations of the connected load. A state-space technique in the frequency domain is applied to the resulting system of equations to facilitate the evaluation of parametric impacts on the system dynamic stability. Also included is a discussion on the system transient stability as affected by sudden changes in some key operating conditions. Some representative results are correlated with experimental data to verify the model and analytic formulation accuracies. Guidelines are given for ranges of the system parameters which will ensure an overall stable operation.

Kankam, M. David↗
NASA NTRS1992

Dynamic analysis of free-piston Stirling engine/linear alternator-load system - Experimentally validated

This paper discusses the effects of a variations in system parameters on the dynamic behavior of a Free-Piston Stirling Engine/Linear Alternator (FPSE/LA)-load system. The mathematical formulations incorporates both the mechanical and thermodynamic properties of the FPSE, as well as the electrical equations of the connected load. State-space technique in the frequency domain is applied to the resulting system of equations to facilitate the evaluation of parametric impacts on the system dynamic stability. Also included is a discussion on the system transient stability as affected by sudden changes in some key operating conditions. Some representative results are correlated with experimental data to verify the model and analytic formulation accuracies. Guidelines are given for ranges of the system parameters which will ensure an overall stable operation.

Kankam, M. D.↗
NASA NTRS2009

Thermal Residual Stress in Environmental Barrier Coated Silicon Nitride - Modeled

When exposed to combustion environments containing moisture both un-reinforced and fiber reinforced silicon based ceramic materials tend to undergo surface recession. To avoid surface recession environmental barrier coating systems are required. However, due to differences in the elastic and thermal properties of the substrate and the environmental barrier coating, thermal residual stresses can be generated in the coated substrate. Depending on their magnitude and nature thermal residual stresses can have significant influence on the strength and fracture behavior of coated substrates. To determine the maximum residual stresses developed during deposition of the coatings, a finite element model (FEM) was developed. Using this model, the thermal residual stresses were predicted in silicon nitride substrates coated with three environmental coating systems namely barium strontium aluminum silicate (BSAS), rare earth mono silicate (REMS) and earth mono di-silicate (REDS). A parametric study was also conducted to determine the influence of coating layer thickness and material parameters on thermal residual stress. Results indicate that z-direction stresses in all three systems are small and negligible, but maximum in-plane stresses can be significant depending on the composition of the constituent layer and the distance from the substrate. The BSAS and REDS systems show much lower thermal residual stresses than REMS system. Parametric analysis indicates that in each system, the thermal residual stresses can be decreased with decreasing the modulus and thickness of the coating.

Ali, Abdul-Aziz↗
NASA NTRSDate not supplied

Design and Comparison of Lunar Sample Return Options

Returning lunar samples to earth is a high priority for NASA in order to better understand Lunar Geology, Lunar formation, and potential resource utilization. Core samples of frozen volatiles from permanently shadowed regions are sought after, but require intensive cryogenic cooling to preserve. Returning samples to Earth using the Orion capsule is restrictive for moderate amounts of mass/volume and thus alternate means of transport are investigated in this paper. The trade-space of potential options includes varying: sample mass amount, sample containment conditions, transfer path from Lunar surface to Earth surface, and various vehicle system trades. An integrated solver is applied with parametric estimators and known system heuristics to effectively estimate size, mass, and power of various subsystems. Modeled subsystems include sample containment, EDL technologies(heat shield, parachute, recovery), power, thermal, avionics, structures, and propulsive systems. Transfer path options include various trajectory options, transfer methods, staging points, and vehicle staging options. A Design of Experiments was conducted to explore the tradespace, to identify sensitivities, and to identify promising designs. Results are detailed for various stakeholder objectives including total mass, sample mass, science return, architecture impacts, and operational flexibility.

Lunar outpost↗
DOE OSTI2025

Coupling magnons to an opto-electronic parametric oscillator

Hybrid magnonic systems have emerged as versatile modular components for quantum signal transduction and sensing applications owing to their capability of connecting distinct quantum platforms. To date, the majority of the magnonic systems have been explored in a local, near-field scheme, due to the close proximity required for realizing a strong coupling between magnons and other excitations. This constraint greatly limits the applicability of magnons in developing remotely coupled, distributed quantum network systems. On the contrary, opto-electronic architectures hosting self-sustained oscillations have been a unique platform for long-haul signal transmission and processing. Here, we integrated an opto-electronic oscillator with a magnonic oscillator consisting of a microwave waveguide and a Y 3 Fe 5 O 12 (YIG) sphere, and demonstrated strong and coherent coupling between YIG’s magnon modes and the opto-electronic oscillator’s characteristic photon modes—revealing the hallmark anti-crossing gap in the measured spectrum. In particular, the photon mode is produced on-demand via a nonlinear, parametric process as stipulated by an external seed pump. Both the internal cavity phase and the external pump phase can be precisely tuned to stabilize either degenerate or nondegenerate auto-oscillations. Our result lays out a new, hybrid platform for investigating the long-distance coupling and nonlinearity in coherent magnonic phenomena, which may be found useful in constructing the future “distributed hybrid magnonic systems.”

36 MATERIALS SCIENCE↗
DOE OSTI2026

Control Parameter Sensitivity Study for Inverter-Based-Resource Dominated Grids: A Small Signal Stability Approach and Framework

The growing adoption of renewable energy is driving the prevalence of inverter-based resources (IBRs) within power grids. Future power grids will integrate both grid-following IBRs (GFM-IBRs) and grid-forming IBRs (GFL-IBRs) alongside synchronous generators. Therefore, it is crucial to perform stability studies that account for all components and especially control interactions related to IBRs. Extensive research has performed to study the IBR-related stability, however, the sensitivity study of IBRs' control parameters on system stability has not been adequately studied yet, especially from a systematic way. Therefore, this paper conducts a small signal stability analysis for a generic grid with multiple types of resources and develops an analytical framework for assessing the sensitivity of control parameters affecting stability margins. To achieve that, the non-autonomous reduced-order non-linear dynamic model is developed for a generic power system with multiple synchronous generator-based resources (SGBRs), GFM-IBRs, and GFL-IBRs. Based on the analytic model, a systematic framework for parametric sensitivity on systems' asymptotic stability is developed. A parameter sensitivity analysis based on eigenvalue methods is proposed. The impact of the droop controllers of GFM-IBRs, PQ-dispatch and the PLL controller of GFL-IBR on the system asymptotic stability is discussed. This sensitivity study is aiming to provide deep insights on control parameters' impact on system stability, and gives direction for parameter tuning in case of instability.

24 POWER TRANSMISSION AND DISTRIBUTION↗
NASA NTRS1992

Engine system assessment study using Martian propellants

A top-level feasibility study was conducted that identified and characterized promising chemical propulsion system designs which use two or more of the following propellant combinations: LOX/H2, LOX/CH4, and LOX/CO. The engine systems examined emphasized the usage of common subsystem/component hardware where possible. In support of this study, numerous mission scenarios were characterized that used various combinations of Earth, lunar, and Mars propellants to establish engine system requirements to assess the promising engine system design concept examined, and to determine overall exploration leverage of such systems compared to state-of-the-art cryogenic (LOX/H2) propulsion systems. Initially in the study, critical propulsion system technologies were assessed. Candidate expander and gas generator cycle LOX/H2/CO, LOX/H2/CH4, and LOX/CO/CH4 engine system designs were parametrically evaluated. From this evaluation baseline, tripropellant Mars Transfer Vehicle (MTV) LOX cooled and bipropellant Lunar Excursion Vehicle (LEV) and Mars Excursion Vehicle (MEV) engine systems were identified. Representative tankage designs for a MTV were also investigated. Re-evaluation of the missions using the baseline engine design showed that in general the slightly lower performance, smaller, lower weight gas generator cycle-based engines required less overall mission Mars and in situ propellant production (ISPP) infrastructure support compared to the larger, heavier, higher performing expander cycle engine systems.

Pelaccio, Dennis↗
NASA NTRS1989

Lunar transfer vehicle design issues with electric propulsion systems

This paper describes parametric design studies of electric propulsion lunar transfer vehicles. In designing a lunar transfer vehicle, selecting the 'best' operating points for the design parameters allows significant reductions in the mass in low earth orbit (LEO) for the mission. These parameters include the specific impulse, the power level, and the propulsion technology. Many of the decisions regarding the operating points are controlled by the propulsion and power system technologies that are available for the spacecraft. The relationship between these technologies is discussed and analyzed here. It is found that both ion and MPD propulsion offer significant LEO mass reductions over O2/H2 for lunar transfer vehicle missions. The recommended operating points for the lunar transfer vehicle are an I(sp) of 5000 lb(f)-s/lb(m) and a 1 MW power level. For large lunar missions, krypton may be the best choice for ion propulsion.

Palaszewski, Bryan↗
DOE OSTI2023

Bi-fidelity modeling of uncertain and partially unknown systems using DeepONets

Recent advances in modeling large-scale, complex physical systems have shifted research focuses towards data-driven techniques. However, generating datasets by simulating complex systems can require significant computational resources. Similarly, acquiring experimental datasets can prove difficult. For these systems, often computationally inexpensive, but in general inaccurate models, known as the low-fidelity models, are available. Here in this paper, we propose a bi-fidelity modeling approach for complex physical systems, where we model the discrepancy between the true system's response and a low-fidelity response in the presence of a small training dataset from the true system's response using a deep operator network, a neural network architecture suitable for approximating nonlinear operators. We apply the approach to systems that have parametric uncertainty and are partially unknown. Three numerical examples are used to show the efficacy of the proposed approach to model uncertain and partially unknown physical systems.

MATHEMATICS AND COMPUTING↗
NASA NTRS1975

Development of a solar-powered residential air conditioner: System optimization preliminary specification

Investigations aimed at the optimization of a baseline Rankine cycle solar powered air conditioner and the development of a preliminary system specification were conducted. Efforts encompassed the following: (1) investigations of the use of recuperators/regenerators to enhance the performance of the baseline system, (2) development of an off-design computer program for system performance prediction, (3) optimization of the turbocompressor design to cover a broad range of conditions and permit operation at low heat source water temperatures, (4) generation of parametric data describing system performance (COP and capacity), (5) development and evaluation of candidate system augmentation concepts and selection of the optimum approach, (6) generation of auxiliary power requirement data, (7) development of a complete solar collector-thermal storage-air conditioner computer program, (8) evaluation of the baseline Rankine air conditioner over a five day period simulating the NASA solar house operation, and (9) evaluation of the air conditioner as a heat pump.

Rousseau, J.↗
NASA NTRS1975

A superfluid helium system for an LST IR experiment

The results are presented of a study program directed toward evaluating the problems associated with cooling an LST instrument to 2 K for a year by using superfluid helium as the cooling means. The results include the parametric analysis of systems using helium only, and systems using helium plus a shield cryogen. A baseline system, using helium only is described. The baseline system is sized for an instrument heat leak of 50 mw. It contains 71 Kg of superfluid helium and has a total, filled weight of 217 Kg. A brief assessment of the technical problems associated with a long life, spaceborne superfluid helium storage system is also made. It is concluded that a one year life, superfluid helium cooling system is feasible, pending experimental verification of a suitable low g vent system.

Breckenridge, R. W., Jr.↗
NASA NTRS1975

NASTRAN as a resource in code development

A case history is presented in which the NASTRAN system provided both guidelines and working software for use in the development of a discrete element program, PATCHES-111. To avoid duplication and to take advantage of the wide spread user familiarity with NASTRAN, the PATCHES-111 system uses NASTRAN bulk data syntax, NASTRAN matrix utilities, and the NASTRAN linkage editor. Problems in developing the program are discussed along with details on the architecture of the PATCHES-111 parametric cubic modeling system. The system includes model construction procedures, checkpoint/restart strategies, and other features.

Stanton, E. L.↗
NASA NTRS1979

Primary electric propulsion for future space missions

The paper presents data and a methodology to allow preliminary definition of electric propulsion systems. The elements comprising the thrust system are described parametrically. As an example, thruster performance is presented as a function of specific impulse and propellant type. Two power management and control (PMAC) approaches are considered to illustrate the use of the methodology. Power source characteristics are disregarded in the system description. One PMAC concept assumes a dc power input to the thrust system and all thruster power conditioned in a conventional manner; the other PMAC approach assumes an ac power source.

Byers, D. C.↗
DOE OSTI2020

The vertical structure of convective mass-flux derived from modern radar systems: Data analysis in support of cumulus parametrization (Final Report)

The project delivered against all its major aims. We first developed a new calibration technique that enabled the construction of a long-term (17 years) calibrated radar dataset for the Darwin region. We documented both the technique and the data set in publications. We then developed a corresponding long-term dataset that characterises the large-scale state of the atmosphere. Equipped with both, we examined the relationship of key convective ensemble characteristics, such as cloud number and size, with the convective environment. In addition to the stated goals, we also applied the data set to i) estimate rainfall efficiency; ii) derive a new metric for convective organisation and iii) derive a longterm data set of convective mass-flux in the Darwin region and apply it to derive estimates of entrainment and detrainment rates in a convective cloud ensemble. Most of the research has been published or submitted for publication and will therefore only briefly summarised here, with links to or copies of the respective papers supplied.

58 GEOSCIENCES↗
NASA NTRS1972

Parametric analysis of RF communications and tracking systems for manned space stations

System performance, system interface compatibility, and system management and operations are analyzed for external and internal communications provided by the modular space station. Mathematical models are utilized to evaluate performances of the various communication links between the MSS and the tracking and data relay satellites, the shuttle, and the ground stations. Communication control design requirements are determined from overall MSS control design and checkout requirements are developed in a related systems study. Parallel design efforts consider equipment configurations for the external communication assembly baseband and the internal communication assembly to accommodate signal transfer and control. The recommended baseline design considers also interfaces between equipment groups and the critical functional and signal characteristics of these interfaces. The data processing assembly has direct communication circuits to the external communication assembly and the control interface is provided via a digital data bus and a remote acquisition and control unit.

Source record↗