Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PIE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2013

Target Operational Experience at the Spallation Neutron Source

The Spallation Neutron Source (SNS) at the Oak Ridge National Laboratory (ORNL) has operated at unprecedented power levels for a short-pulse spallation source. Target operations have been successful but not without difficulties. Three targets out of the eight used to date have ended life unexpectedly causing interruptions to the neutron science users. The first of a kind mercury target design experiences beam-pulse induced cavitation damage that is suspected in one of the target leaks. The two other targets suffered early failures due to defective welds. Diagnosing the causes of target leaks and understanding of the progression of cavitation erosion and radiation damage effects has made use of post-irradiation examination (PIE) capabilities. As a result of PIE, review of quality assurance practices and related investigations, design changes are being implemented and manufacturing oversight improved. This paper describes SNS target operating experience, including the more important observations and lessons learned.

Acclerator↗
DOE OSTI2014

Investigating Enhanced Thorium Ionization in TIMS Using Re/Pt Porous Ion Emitters

Thermal ionization mass spectrometry (TIMS) is a widely used, benchmark method in the isotopic analysis of actinides relevant to various nuclear and geological fields. Despite significant previous use and inherent advantages, however, poor sample ionization continues to hamper the use of TIMS in the measurement of trace species; actinide ionization efficiencies frequently fall below 0.1 % using traditional instrument sources. Factors leading to poor ionization are compounded in the measurement of several highly refractory metals (e.g. U and Th) that may provide key signatures data in non-proliferation, safeguards and forensics efforts. Herein, a relatively new TIMS ion source strategy, employing porous ion emitters (PIEs) atop traditional filament assemblies, is investigated for the first time as a straightforward means of enhancing the ionization of Th, which is arguably a worst case scenario for TIMS-based actinide measurements. These sources yielded up to 410% greater Th sample utilization, relative to previously published values and in-house measurements collected using traditional methods. Accompanying scanning electron microscopy (SEM) investigations provide preliminary insight into possible mechanisms of PIE functioning and explore the impacts that extended heating have on the constructed source’s structure and composition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2016

Progress In Developing Laser Based Post Irradiation Examination Infrastructure

To be able to understand the performance of reactor fuels and materials, irradiated materials must be characterized effectively and efficiently in a high rad environment. The characterization work must be performed remotely and in an environment hostile to instrumentation. Laser based characterization techniques provide the ability to be remote and robust in a hot-cell environment. Laser based instrumentation also can provide high spatial resolution suitable for scanning and imaging large areas. The INL is currently developing three laser based Post Irradiation Examination (PIE) stations for the Hot Fuel Examination Facility at the INL. These laser based systems will characterize irradiated materials and fuels. The characterization systems are the following: Laser Shock Laser based ultrasonic C-scan system Gas Assay, Sample, and Recharge system (GASR, up-grade to an existing system). The laser shock technique will characterize material properties and failure loads/mechanisms in various materials such as LWR fuel, plate fuel, and next generation fuel forms, for PIE in high radiation areas. The laser shock-technique induces large amplitude shock waves to mechanically characterize interfaces such as the fuel-clad bond. The shock wave travels as a compression wave through the material to the free (unconfined) back surface and reflects back through the material under test as a rarefaction (tensile) wave. This rarefaction wave is the physical mechanism that produces internal de-lamination failure. As part of the laser shock system, a laser-based ultrasonic C-scan system will be used to detect and characterize debonding caused by the laser shock technique. The laser ultrasonic system will be fully capable of performing classical non-destructive evaluation testing and imaging functions such as microstructure characterization, flaw detection and dimensional metrology in complex components. The purpose of the GASR is to measure the pressure/volume of the plenum of an irradiated fuel element and obtain fission gas samples for analysis. The study of pressure and volume in the plenum of an irradiated fuel element and the analysis of fission gases released from the fuel is important to understanding the performance of reactor fuels and materials. This system may also be used to measure the pressure/volume of other components (such as control blades) and obtain gas samples from these components for analysis. The main function of the laser in this application is to puncture the fuel element to allow the fission gas to escape and if necessary to weld the spot close. The GASR station will have the inherent capability to perform cutting welding and joining functions within a hot-cell.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2017

ON-GOING STATUS OF KJRR FUEL (U-7MO) QUALIFICATION

In order to cope with global shortage of Mo-99 supplies and with growing demand of neutron transmutation doping, KJRR construction plan has been launched since April 2012 to provide self-sufficiency of domestic RI demand, and to extend Si doping capacity for power device market growth. Through comprehensive surveillance of the fuels in-reactor behavior, KAERI has selected the fuel meat of U-7%Mo dispersion in an aluminum matrix with 5wt%Si for the KJRR fuel. As part of the efforts for fuel licensing and qualification of the KJRR fuel, an LTA irradiation test at the ATR started from November 2015 was successfully completed by reaching at 219 EFPD in the end of February 2017. Together with the results of HAMP-1 already completed irradiation and PIE, the successful irradiation of the LTA also demonstrates the fuel integrity under more rigorous conditions than the KJRR operation conditions. This paper updates the current status of the KJRR U7Mo (8 g-U/cm3) LTA irradiation and PIE plan up to date as of February 2017.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2018

Post-irradiation Examinations of High Burnup PWR Rods

The High Burnup Spent Fuel Data Project (herein referred to as the “project”), sponsored by the US Department of Energy (DOE) Office of Nuclear Energy (NE), is focused on experimentally evaluating the effects of long-term storage and transportation on high burnup (HBU) (defined as >45 gigawatt days per metric ton uranium) pressurized water reactor (PWR) spent nuclear fuel (SNF) [1]. To support this project, in the fall of 2017, an instrumented bolted-lid cask (project cask) at the North Anna reactor site was loaded with intact, HBU PWR fuel assemblies (project assemblies) having four different kinds of cladding and will be reopened in approximately 10-years for inspection. To support pre- and post-storage SNF rod characterization, 25 “sister rods” that are similar to the rods being stored in the project cask were extracted from seven different fuel assemblies at the North Anna nuclear power plant for post-irradiation examination (PIE).The sister rod testing program has multiple objectives, including: 1) Baseline testing to provide essential information on the physical condition and properties of the cladding and the fuel in the cladding prior to the loading, drying, and long-term dry storage process (analogous to an experiment control group). Similar tests are expected to be performed at the end of the 10-year storage period on rods extracted from the cask to identify any changes in the properties of the fuel rods that may have occurred during the dry storage period; and 2) Tests to provide material property and physical data using accelerated separate effects tests (SETs) and small-scale tests (SSTs) to explore a wide range of conditions that may occur for other dry storage systems and/or while the fuel is being transported after aging.Testing will be focused on understanding overall SNF rod strength and durability, and be comprised of both composite fuel and defueled clad testing with a focus on measuring cladding material and mechanical properties. Nondestructive testing is currently underway and plans are being updated to support the initial set of destructive tests that are expected to begin by early 2018. While the data generated can be used for multiple purposes, a primary goal of the sister rod PIE data and associated measured mechanical properties are expected to support existing fuel storage licensing and relicensing activities by addressing identified knowledge gaps, and enhance the technical bases for post-storage transportation, handling, and consolidation activities [1]. This paper presents results obtained from the sister rod testing to date, and describes some of the planned measurements, equipment, and procedures that will be implemented for the initial set of destructive examinations.

Montgomery, Rose↗
DOE OSTI2019

Poster and Slide: Energy Loss: Exploring Dissipation Pathways from Ions to In-reactor

Young Researcher Association is hosting an early career poster and networking session on July 25th, 2019. The poster session is designed to provide an overview of the researcher’s experience prior to employment at INL, and their current area of research and interests. The following is a brief description of the major sections of the poster. Before starting at INL in May of this year, my research focused on exploring the effects of electronic and nuclear energy loss on the damage evolution of Ti3SiC2 MAX phase during energetic irradiations. A series of ion irradiations revealed a threshold in electronic energy loss (Se), above which the formation of a FCC-MAX structure is enhanced, accommodating point defects and alleviating lattice strain. However, systematically separating the effects reveals that increasing Se/Sn suppresses this phase formation, thus allowing the strain from point defects to increase and saturate. Presently my research supports Post Irradiation Examination (PIE) of U-Mo fuel for the USHPRR and KJRR programs. The PIE evaluation currently consists of non-destructive examination (NDE) of fuel plates irradiated in the Advanced Test Reactor (ATR), focusing on plate profilometry and fuel swelling analysis. NDE will culminate in finalizing the destructive examination (DE) test plans and execution of said DE. Additionally, I am interested in exploring the roles that different energy dissipation pathways play in the damage evolution of the U-Mo fuel, exploring the mechanisms by which the fuel remains in its meta-stable phase under irradiation at high temperatures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2019

Test Plan for Reirradiation and 1200°C Heating Test of AGR-3/4 Compact 8-1

Post irradiation examination (PIE) and heating tests of tristructural isotropic (TRISO)-coated fuel particles, fuel compacts, and graphite from Advanced Gas Reactor (AGR) irradiation experiment AGR 3/4 are in progress. The AGR-3/4 test train consisted of twelve separate capsules irradiated in the northeast flux trap of the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) from December 14, 2011, to April 12, 2014 (Collin 2015b). This test plan describes the reirradiation and subsequent heating test of AGR-3/4 Compact 8-1. One of the main goals of this test is to assess the retention of short-lived fission products I-131 (t1/2 = 8.02 d) and Xe-133 (t1/2 = 5.2 d) in fuel kernels. To generate short-lived fission products, the compact will first be reirradiated in the Neutron Radiography Reactor (NRAD). Following reirradiation, the compact will be removed from NRAD, gamma scanned on the Precision Gamma Scanner (PGS), and then loaded into the Fuel Accident Condition Simulator (FACS) furnace for heating at 1200°C. Fission gases and condensable fission products released from the compact will be collected in the Fission Gas Monitoring System (FGMS) and the FACS condensation plates, respectively. The planned uses of AGR-3/4 compacts (including heating testing and destructive analysis) are discussed in the AGR-3/4 PIE plan (Demkowicz 2017). Significant portions of this plan have been completed and additional samples are being used for purposes not captured in that plan.

42 ENGINEERING↗
DOE OSTI2019

Test Plan for Reirradiation and 1600°C Heating Test of AGR-3/4 Compact 3-1

Post irradiation examination (PIE) and heating tests of tristructural isotropic (TRISO)-coated fuel particles, fuel compacts, and graphite from Advanced Gas Reactor (AGR) irradiation experiment AGR 3/4 are in progress. The AGR-3/4 test train consisted of twelve separate capsules irradiated in the northeast flux trap of the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) from December 14, 2011, to April 12, 2014 (Collin 2015b). This test plan describes the reirradiation and subsequent heating test of AGR-3/4 Compact 3-1. One of the main goals of this test is to assess the retention of short-lived fission products I-131 (t1/2 = 8.02 d) and Xe-133 (t1/2 = 5.2 d) in fuel kernels. To generate short-lived fission products, the compact will first be reirradiated in the Neutron Radiography Reactor (NRAD). Following reirradiation, the compact will be removed from NRAD, gamma scanned on the Precision Gamma Scanner (PGS), and then loaded into the Fuel Accident Condition Simulator (FACS) furnace for heating at 1600°C. Fission gases and condensable fission products released from the compact will be collected in the Fission Gas Monitoring System (FGMS) and the FACS condensation plates, respectively. The planned uses of AGR-3/4 compacts (including heating testing and destructive analysis) are discussed in the AGR-3/4 PIE plan (Demkowicz 2017).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Comparison of Fission Product Release Predictions using PARFUME with Results from the AGR-2 Irradiation Experiment

The PARFUME (PARticle FUel ModEl) code was used to predict fission product release from tristructural isotropic (TRISO) coated fuel particles and compacts during the second irradiation experiment (AGR-2) of the Advanced Gas Reactor Fuel Development and Qualification Program. The PARFUME model for the Advanced Gas reactor (AGR)GR-2 experiment used the fuel compact volume average temperature for each of the 560 days of irradiation to calculate the release of fission products of silver, cesium, and strontium from a representative particle for a select number of AGR -2 compacts. In addition, safety tests were performed on 15 compacts ranging from 1500 to 1800°C to determine fission product release at temperatures that bound reactor accident conditions. PARFUME was used to calculate the fission product release of silver, cesium, strontium, and krypton during these safety tests. Post-irradiation examination (PIE) measurements provided the data on release of fission products from the fuel compacts and fuel particles, and retention of fission products in the compacts outside the silicon carbide (SiC) layer. The predicted fraction release from PARFUME was then compared to PIE measurements.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2019

Status of LEU U-10Mo Monolithic Fuel Testing and Qualification Efforts to Support US High Performance Research Reactor Conversions

The US High Performance Research Reactor Project has begun a new phase of fuel testing and post irradiation examination (PIE) of plate-type low-enriched uranium (LEU) U-10Mo Monolithic fuel. The testing campaigns are intended to first confirm that the fuel performance behavior of commercially produced fuel matches that of the lab-scale fabricated fuel tested during development, followed by qualification of the U-10Mo monolithic fuel system through the US Nuclear Regulatory Commission. Planned tests include miniature-plate, full-size plate, and fuel element irradiations, during which fuel test specimens fabricated with qualified processes will be irradiated under conditions that bound the NRC-regulated reactors in order to demonstrate that the fuel meets the overarching fuel performance requirements of 1) maintaining mechanical integrity 2) maintaining geometric stability and 3) exhibiting stable and predictable behavior. The MP-1 test, with the objective of confirming fuel performance behavior, is currently undergoing irradiation in the Advanced Test Reactor and PIE in INL hot cells. Status of upcoming qualification and licensing test design activities and highlights of initial as-fabricated characterization and testing results from the MP-1 test will be provided.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2016

Analyses of SPERT-CDC test 859 by FEMAXI-7 and RANNS codes

In the current Japanese regulation concerning fuel safety of water-cooled reactors, the criterion of fuel failure due to pellet-cladding mechanical interaction (PCMI) in a burnup range of 25-40 GWd/t is determined substantially based on the result of SPERT-CDC test 859 (SPERT859). However, there is room for discussion if the result of SPERT859 test rod with a burnup of 31.8 GWd/t represents the failure behavior of the fuel rod for commercial light water reactor because it was reported in some literatures that the cladding of SPERT859 test rod corroded excessively during pre-irradiation. On the other hand, the oxide thickness on the cladding of SPERT859 test rod was not reported in the data of its post-irradiation examinations (PIEs) after pre-irradiation, and the probability of the excessive corrosion on the cladding of the test rod and the effect of such excessive corrosion on the fuel enthalpy at failure of the test rod has not yet been clarified. In this study, the oxide thickness of the cladding formed on the cladding outer surface of SPERT859 test rod and its fuel enthalpy at failure due to PCMI under this corrosion condition were analyzed by using fuel performance codes FEMAXI-7 and RANNS. From the analysis results of FEMAXI-7, it was found that the excessive corrosion of the cladding of the test rod should be assumed to reproduce the fuel outer diameter measured in PIEs after pre-irradiation. The fuel enthalpy at failure of the test rod was calculated by using RANNS, and the calculated fuel enthalpy at failure was relatively close to the value of SPERT859 test rod. These results suggested that the fuel enthalpy at failure of SPERT859 was affected by the excessive corrosion on the cladding of the test rod and was likely lower than that of the typical fuel for light water reactors. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2016

Advantages gained by Optimized ZIRLO and AXIOM PWR cladding materials

In support of industry's demands for higher performance cladding alloy materials, the Optimized ZIRLO alloy was developed as an evolutionary improvement of the ZIRLO alloy to obtain a significant improvement in corrosion performance and hydrogen pickup while maintaining the overall robust performance of ZIRLO alloy. Currently with operating experience in over 40 plants and burnup reaching over 70 GWd/MTU, a majority of the Westinghouse-fueled US PWR fleet, covering almost all Westinghouse fuel designs, has adopted full regions of Optimized ZIRLO cladding. Across all of these applications, Optimized ZIRLO cladding has demonstrated greatly improved corrosion performance and structural stability. These demonstrated improvements offer increased operational margin and flexibility, in support of industry trends toward increased core operating fuel duties and evolving regulatory requirements such as accident scenarios. Underpinning these benefits are the extensive post irradiation exam (PIE) data obtained from both pool-side and hot-cell exams for Optimized ZIRLO cladding. Building on the successes of Optimized ZIRLO cladding, and in recognition of increasingly challenging fuel management practices, and revised LOCA regulatory rules restricting cladding hydrogen content, AXIOM cladding is being rolled out for full lead test assembly irradiation. The AXIOM alloy, Westinghouse's next generation robust alloy targeting very high fuel duties, is designed to provide improved corrosion resistance, lower hydrogen pick-up, and lower creep and growth compared to current Westinghouse products. AXIOM cladding has been irradiated in a variety of reactors worldwide, including both commercial and test reactors. Extensive PIE data is available for various burnup levels, with leading rods approaching 75 GWd/MTU. The AXIOM composition was selected to ensure enhanced operating performance on multiple fronts, including the optimum combination of corrosion resistance and wear resistance, reduced hydrogen pick-up, improved dimensional stability, and robustness in aggressive coolant chemistry conditions. The present paper provides high burnup performance data, capturing the advantages gained by introducing Optimized ZIRLO and AXIOM alloy as PWR cladding materials. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2018

Post-irradiation Examinations of High Burnup PWR Rods - 18456

The High Burnup Spent Fuel Data Project (herein referred to as the 'project'), sponsored by the US Department of Energy (DOE) Office of Nuclear Energy (NE), is focused on experimentally evaluating the effects of long-term storage and transportation on high burnup (HBU) (defined as >45 gigawatt days per metric ton uranium) pressurized water reactor (PWR) spent nuclear fuel (SNF) [1]. To support this project, in the fall of 2017, an instrumented bolted-lid cask (project cask) at the North Anna reactor site was loaded with intact, HBU PWR fuel assemblies (project assemblies) having four different kinds of cladding and will be reopened in approximately 10-years for inspection. To support pre- and post-storage SNF rod characterization, 25 'sister rods' that are similar to the rods being stored in the project cask were extracted from seven different fuel assemblies at the North Anna nuclear power plant for post-irradiation examination (PIE). The sister rod testing program has multiple objectives, including: 1) Baseline testing to provide essential information on the physical condition and properties of the cladding and the fuel in the cladding prior to the loading, drying, and long-term dry storage process (analogous to an experiment control group). Similar tests are expected to be performed at the end of the 10-year storage period on rods extracted from the cask to identify any changes in the properties of the fuel rods that may have occurred during the dry storage period; and 2) Tests to provide material property and physical data using accelerated separate effects tests (SETs) and small-scale tests (SSTs) to explore a wide range of conditions that may occur for other dry storage systems and/or while the fuel is being transported after aging. Testing will be focused on understanding overall SNF rod strength and durability, and be comprised of both composite fuel and defueled clad testing with a focus on measuring cladding material and mechanical properties. Nondestructive testing is currently underway and plans are being updated to support the initial set of destructive tests that are expected to begin by early 2018. While the data generated can be used for multiple purposes, a primary goal of the sister rod PIE data and associated measured mechanical properties are expected to support existing fuel storage licensing and relicensing activities by addressing identified knowledge gaps, and enhance the technical bases for post-storage transportation, handling, and consolidation activities [1]. This paper presents results obtained from the sister rod testing to date, and describes some of the planned measurements, equipment, and procedures that will be implemented for the initial set of destructive examinations. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2016

Irradiation in the Swiss Spallation Neutron Source and its Applications

In high power (∼ 1 MW or higher) spallation targets being operated or developed for different attractive applications such as neutron scattering science and technology or accelerator driven systems (ADS) for nuclear waste transmutation, both target and structural materials are exposed to intensive irradiation of high energy protons and spallation neutrons. Since spallation reactions induced by high energy protons can produce helium (He) and hydrogen (H) and other transmutation elements at very high rates, the behavior of materials used in a spallation irradiation environment can be much different from those observed from materials irradiated with neutrons in fission reactors. Therefore, the damage induced by spallation irradiation cannot be simply simulated by fission neutron irradiation experiments. Seven irradiation experiments have been conducted in the targets of the Swiss Spallation Neutron Source (SINQ) at the Paul Scherrer Institute (PSI) since 1998 within a broad international collaboration with Commissariat a L'energie Atomique Centre d'Etudes de Saclay (CEA), Forschungszentrum Juelich (FZJ), Japan Atomic Energy Agency (JAEA), Los Alamos National Laboratory (LANL), Oak Ridge National Laboratory (ORNL), University California Santa Barbara (UCSB) and several institutes of Chinese Academy of Sciences. More than 7000 samples from various Al-, Ti-, Fe-, Ni-, Zr-, and W-alloys and SiC/SiC, C/SiC and MAX-phase ceramics composites have been irradiated to doses up to ∼25 dpa (in Fe) and ∼2000 appm He at temperatures up to ∼800 deg. C. In addition, quite many specimens were irradiated in contact with stagnant liquid metals such as Hg, PbBi, PbLi etc. Dedicated post-irradiation examinations (PIE) have been performed, together with the international collaborators. Various mechanical tests including tensile, bend, Charpy-impact, small punch and hardness have been carried out to obtain the mechanical properties of the materials after irradiation. The microstructural changes in the irradiated specimens have been investigated by means of transmission electron microscopy, positron annihilation spectroscopy, atom probe tomography etc. Many novel results have been obtained from the PIE conducted by PSI and other STIP partner laboratories. The DBTT-shift of different FM steels increases more or less linearly with dose after irradiation in the SINQ target, while it saturates at a level of few dpa in fission neutron irradiation cases. This phenomenon can be mostly attributed to helium effects. In addition to the strong embrittlement effect, pronounced hardening effect was also detected in high dose specimens, which was contributed by high density helium bubbles.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Initial Results from the High Fluence UCSB ATR-2 Irradiation

A primary focus of the Department of Energy, Office of Nuclear Energy Light Water Reactor Sustainability Program (LWRSP) is the safe operation of nuclear reactors to extended lifetimes of up to 80 years. One of the primary reactor components of concern is the reactor pressure vessel (RPV), which is increasingly embrittled over time due to damage from high energy neutrons created in the reactor core. Radiation damage leads to the formation of nm-scale precipitates and solute-defect clusters, which result in an increase in the steel's ductile to brittle transition temperature. Transition temperature shifts (TTS) are used to quantify and regulate embrittlement. Extended life operation will subject some RPVs to higher neutron fluences than previously experienced by in-service vessels. Thus, robust prediction methods must be developed that ensure the safety of our nation's fleet of reactors. Current models underpredict embrittlement data from high flux test reactor irradiations at extended life fluences. It has been hypothesized that one reason for this underprediction is the formation of so-called 'Late- Blooming Phase' Mn-Ni-Si precipitates, which form and grow only at high fluence and that are currently not included in regulatory models. Recent research has demonstrated the existence of high volume fractions of intermetallic Mn-Ni-Si precipitate (MNSP) phases at high fluence and have generated significant insight into their character. However, a number of questions remain regarding MNSPs, such as: 1) what alloys are most susceptible to MNSP formation; 2) how is MNSP formation affected by flux (φ), fluence (φt) and irradiation temperature (T{sub irr}); and, 3) how to accurately predict TTS under extended life low flux service conditions? The fact that no two RPVs are exactly the same, both in terms of the steel composition and vessel service conditions, makes these questions particularly difficult to answer. Further, understanding the effect of flux differences between test reactor irradiations and in-vessel service is absolutely critical. Hence, physical models must be developed that predict TTS as a function of alloy solute content and vessel service conditions. A large-scale irradiation designed to develop and validate an extended life embrittlement prediction model was recently completed in the Advanced Test Reactor (ATR) at the Idaho National Laboratory as part of the DOE sponsored Nuclear Scientific User Facilities. This experiment, called the UCSB ATR-2 irradiation, is a collaboration between Oak Ridge National Lab (ORNL) and the University of California, Santa Barbara (UCSB) and is now primarily supported by the DOE Light Water Reactor Sustainability Program. The experiment is designed to investigate the single and combined effects of neutron φ, φt, T{sub irr} and alloy chemistry on precipitate formation, hardening and embrittlement. While postirradiation examinations (PIE) is ongoing, and is expected to take several years to complete, the first preliminary results are presented below. It should also be noted that Rolls-Royce has been a collaborator in UCSB ATR-2 from the start, and there are several other national and international institutions supporting the PIE. (authors)

36 MATERIALS SCIENCE↗
DOE OSTI2016

Comparison of silver release predictions using PARFUME with results from the AGR-2 irradiation experiment - 18579

The PARFUME (Particle Fuel Model) code was used to predict silver release from tri-structural isotropic (TRISO) coated fuel particles and compacts during the second irradiation experiment (AGR-2) of the Advanced Gas Reactor Fuel Development and Qualification program. The PARFUME model for the AGR-2 experiment used the fuel compact volume average temperature for each of the 559 days of irradiation to calculate the release of fission product silver from a representative particle for a select number of AGR-2 compacts and individual fuel particles containing either mixed uranium carbide/oxide (UCO) or 100% uranium dioxide (UO{sub 2}) kernels. Post-irradiation examination (PIE) measurements were performed to provide data on release of silver from these compacts and individual fuel particles. The available experimental fractional releases of silver were compared to their corresponding PARFUME predictions. Preliminary comparisons show that PARFUME under-predicts the PIE results in UCO compacts and is in reasonable agreement with experimental data for UO{sub 2} compacts. The accuracy of PARFUME predictions is impacted by the code limitations in the modeling of the temporal and spatial distributions of the temperature across the compacts. Nevertheless, the comparisons on silver release lie within the same order of magnitude. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2017

Post Irradiation Examination of SiC Tube Subjected to Simultaneous Irradiation and Radial High Heat Flux

Silicon carbide (SiC) based composite is considered among leading candidate materials for accident tolerant fuel (ATF) cladding in light water reactors (LWRs) because of its outstanding irradiation and oxidation resistance, as well as low neutron absorption. Under normal operation conditions, the synergism between neutron irradiation and a high radial heat flux though the cladding thickness is expected to produce significant stress. This stress is attributed to a significant through-thickness temperature gradient and the resulting differential swelling strain due the highly temperature-dependent point-defect swelling of SiC. Although modeling of the in-pile stress state of SiC cladding has been conducted using finite element analysis, the analysis is challenging because of the complex stress state that depends upon swelling, irradiation creep, and thermal conductivity, all of which are both temperature and dose-dependent. These integral models have not yet been verified by experiments. In order to experimentally validate the multi-physics thermo-mechanical models of ATF SiC cladding during operation, SiC tube specimens have been irradiated under a high radial heat flux. This paper reports preliminary results from the post-irradiation examination (PIE) in on-going project supported by the U.S. Department of Energy's Nuclear Science User Facility program. The objectives of the PIE are (1) determination of the irradiation temperature distribution within the tube specimens, and (2) evaluation of the state and magnitude of the stress within the tube specimens arising from the temperature gradient. This paper mainly presents findings for objective (1)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2017

Volatility Studies of Lanthanide Hexafluoroacetylacetone Chelates

The Advanced Fuels Campaign within the Fuel Cycle Research and Development program of the Department of Energy (DOE) Office of Nuclear Energy is currently investigating a number of advanced nuclear fuel cladding concepts to improve the accident tolerance of light water reactors (LWRs). Some of the leading candidates to replace traditional zirconium-based cladding are alumina-forming ferritic alloys (e.g., FeCrAl) and silicon carbide (SiC) composites. Oak Ridge National Laboratory has developed experimental designs to irradiate thin-walled cladding tubes with representative geometry in the High Flux Isotope Reactor (HFIR) under relevant LWR temperatures and in some cases under prototypic heat flux. These designs allow for post-irradiation examination (PIE) of cladding which closely resembles expected commercially viable geometries and microstructures. PIE will include studies of dimensional change, microstructure variation, mechanical performance, etc. The experiments were designed using relatively inexpensive rabbit capsules for the irradiation vehicle. The simplistic designs combined with the extremely high neutron flux in the HFIR allow for rapid testing of a large test matrix, thus reducing the time and cost for moving advanced cladding materials closer to commercialization. This work describes the capsule designs that have been developed at ORNL, some initial results, and plans for future irradiations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗