Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ORR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Highly Durable and Active Pt/Sb-Doped SnO 2 Oxygen Reduction Reaction Electrocatalysts Produced by Atomic Layer Deposition

Platinum supported on mixed-metal oxides (MMOs) are a class of active and durable cathode catalysts for proton exchange membrane fuel cell (PEMFC) due to a combination of the high oxidative stability of the supports and strong-metal-support interactions (SMSI) that enable them to exceed the activity of Pt/C. Herein, we solve a significant remaining challenge with Pt/MMO systems, namely the relatively low surface area and porosity. This is achieved by dispersing nearly-uniform Pt clusters using atomic layer deposition (ALD) on highly conductive (6.2 S/cm) and stable antimony doped tin dioxide (ATO) support. ALD-Pt/ATO exhibited significantly higher electrochemically active surface area (ECSA) (74 m 2 /g) and oxygen reduction reaction (ORR) catalytic activity (102 mA/mg Pt at 0.9 V vs. RHE) compared to Pt/ATO synthesized using ethylene glycol (ECSA=31 m 2 /g Pt , mass activity=52 mA/mg Pt at 0.9 V vs. RHE) and formic acid reduction methods (ECSA=28 m 2 /g Pt , mass activity=46 mA/mg Pt at 0.9 V vs. RHE). Further characterization showed that wet chemical methods resulted in poorer Pt particle dispersion, poor control over Pt particle size distribution and chemical degradation of the support (during Pt deposition). Given the near-ideal Pt particle size distribution of the ALD-Pt/ATO, particle size growth and loss of ECSA was found to be minimal over the course of rigorous potential cycling. Thus, after 10,000 potential cycles between 1V and 1.5V vs. RHE, ALD-Pt/ATO and other Pt/ATOs were found to retain 100% of their initial ECSA compared to 57.6% retention for Pt/C. Upon testing in a H 2 /air PEMFC, following 1,000 potential cycles, the change in ALD-Pt/ATO performance was negligible while Pt/C exhibited a 68.2% loss of initial peak power density. Thus, ALD-Pt/ATO is an active and highly durable ORR electrocatalyst in PEMFCs under start-up-shut down conditions.

25 ENERGY STORAGE↗
DOE OSTI2021

Electronic Structure, Chemical Bonding and Electrocatalytic Activity of Novel Ba(Fe0.7Ta0.3)O3-d Compounds

Ba(Fe0.7Ta0.3)O3-d (BFTO) compounds were synthesized using conventional, high-temperature solid-state ceramic reaction method by varying the sintering temperature (Ts=1200-1350 °C). The crystal structure, electronic structure and electrocatalytic activity of BFTO compounds were evaluated. Processing temperature induced phase transformations and structural quality influences the electronic structure and electrocatalytic activity of BFTO compounds. At Ts=1200 oC, Ba(Fe0.7Ta0.3)O3-d stabilizes in mixed phase of orthorhombic + rhombohedral phase (Amm2 + R3m). With increasing Ts (=1250 oC), Ba(Fe0.7Ta0.3)O3-d ceramics stabilize in tetragonal + rhombohedral [P4mm + R3m] mixed phase with a variation in the quantity of respective phases. High-resolution X-ray photoelectron spectroscopy of constituent elements, namely, Ba 3d, Fe2p, Ta 4f and O 1s reveal the electronic structure changes due to changes in chemical environment resulted from structural transformation. The electrocatalytic activity of BFTO was evaluated towards hydrogen evolution reaction (HER) and oxygen reduction reaction (ORR). Though all the samples demonstrated appreciable electrocatalytic properties, the best electrochemical catalytic activity was shown by BFTO samples sintered at 1350 °C. BFTO-1350 oC showed an onset potential of -0.690 V vs. RHE for HER and an onset potential of 0.73 V vs. RHE for ORR indicating its significant electrocatalytic performance. A general increase in activity with sintering temperature is potentially due to the improved structural quality of the BFTO ceramics. In addition to offering the fundamental insights into solid state materials based on doped BaTiO3 for electrocatalysis, the present work may contribute to the design and development of materials for high-temperature electrocatalytic converters.

Ba(Fe0.7Ta0.3)O3-d, Phase Transformation↗
DOE OSTI2021

Toward Optimizing Electrospun Nanofiber Fuel Cell Catalyst Layers: Microstructure and Pt Accessibility

This work investigates how local ionomer/platinum (Pt) interactions and ionomer distribution in electrospun Pt/Vulcan nanofiber electrodes impact ionomer coverage, proton accessibility, and oxygen reduction reaction (ORR) performance in proton-exchange membrane fuel cells. Insights from various in situ electrochemical diagnostics were utilized in conjunction with ex situ microscopic characterization to understand how the electrode microstructure—both at the aggregate level and near the ionomer/platinum interface—is affected by electrospinning in comparison to ultrasonic spraying. The effect of the carrier polymer poly(acrylic acid) (PAA) concentration from 5–20 wt % (with respect to total ink solids) on the resulting nanofiber morphology is discussed. Electron microscopy observations and CO displacement measurements indicated that Pt/Vulcan nanofibers prepared with a higher PAA concentration (15 wt %) were conformally coated with a film of ionomer on the exterior of the fiber, which resulted in an overall lower ionomer coverage on both Pt and carbon throughout the fiber diameter. In contrast, 10 wt % PAA leads to a uniform intrafiber distribution of the ionomer within the fibers, increasing the overall ionomer coverage and proton accessibility under both wet and dry conditions. These differences in the local ionomer coverage on Pt between 10 and 15 wt % PAA were also attributed to differences in the adsorption/interaction affinities between PAA and the ionomer onto the catalyst surface in the ink using zeta potential measurements. Additional fuel cell electrochemical tests on the electrospun electrodes show improvements in ORR kinetics and high-current-density H 2 /air performance compared to the ultrasonically sprayed electrodes.

25 ENERGY STORAGE↗
DOE OSTI2025

Pyrolysis in Molten Salts Converts Plastics into a Mesoporous Electrocatalyst with a High Density of Atomic Fe–N–C Active Site

Upcycling plastic waste into value-added products is a promising strategy for both economic and environmental sustainability. However, achieving control over structure–property correlations during the upcycling process remains challenging. Here, in this study, we investigate the modulation of active site formation during pyrolytic conversion of plastics to carbon by composition-controlled molten salts. Using melamine formaldehyde (MF) foams as a precursor, we demonstrate that their pyrolysis in eutectic chloride molten salts with Fe 2+ , Na + , and K + ions directs the carbonization process toward the formation of mesoporous functional carbon enriched with atomically dispersed Fe–N–C sites, which are well-known for their catalytic activity in oxygen reduction reaction (ORR). Compared to pyrolysis in the FeCl 2 -only salt, the incorporation of alkali metal ions (Na + , K + ) in the eutectic mixture facilitates nitrogen retention in the carbon matrix and modulates iron speciation. This synergistic environment promotes a higher density and more uniform dispersion of Fe–N–C moieties within the carbon matrix. Consequently, the resulting catalyst exhibits a high surface area, hierarchical porosity, and improved electrochemical properties. When tested as an ORR catalyst, the Fe–N–C-enriched catalyst delivers a high half-wave potential (E 1/2 = 0.875 V vs RHE) with nearly exclusive 4e – pathway. These properties are comparable to those of commercial Pt/C catalysts, along with improved stability.

Fe−N−C active sites↗
DOE OSTI2026

Graphene Quantum Dot Composites Embedded with CoZn Alloy Nanoparticles for Enhanced Oxygen Reduction and Evolution Reactions

Developing efficient and durable electrocatalysts for oxygen reduction (ORR) and oxygen evolution reactions (OER) is crucial for energy conversion technologies. In this study, core–shell graphene quantum dot (GQD) composites embedded with Co, Zn, and CoZn alloy nanoparticles were synthesized using a solid-state microwave synthesis method and systematically investigated for their electrochemical performance. The structural and compositional analyses confirm that the integration of transition metal nanoparticles enhances the electronic properties of GQDs, providing abundant active sites and facilitating charge transfer. Electrochemical characterization reveals that GQD-CoZn-3 (GQD:Co:Zn = 10.5:0.5:0.5) exhibits superior ORR and OER catalytic activities, achieving the highest current densities of 205 A g–1 and 102 A g–1 at 100 mV s–1, respectively. These performance values surpass those of pristine GQDs and single-metal (Co or Zn) embedded counterparts, emphasizing the strong synergistic effect between the CoZn alloy and the functionalized carbon framework. Impedance measurements further reveal a substantial reduction in charge-transfer resistance, while chronoamperometry tests demonstrate excellent catalytic stability and CO tolerance, highlighting the robustness of the core–shell GQD structure. These findings provide valuable insights into the design of advanced carbon-based electrocatalysts for energy applications.

Panda, Pradeep Kumar↗
DOE OSTI2024

Surface Decoration of Platinum Catalysts by ZrO 2– x Nanoclusters for Durable Fuel Cell Applications

Improving the activity and durability of carbon-supported platinum catalysts for the oxygen-reduction reaction (ORR) in acidic electrolytes is crucial to reducing the high overpotentials and power loss over time in proton-exchange membrane fuel cells (PEMFCs). We found that platinum nanoparticle catalyst deposited on an engineered carbon support in the presence of zirconium enabled higher ORR activity and 25% better retention in electrochemically active surface area (ECSA), thereby improving durability. The use of zirconium precursor in the carbon synthesis process led to the formation of atomically dispersed Zr and ZrO 2 nanoparticles on the support. Upon Pt deposition and subsequent heat treatment, the ZrO 2 particles preferentially rearranged on and around the platinum nanoparticles in a chemically reduced form as zirconium suboxide (ZrO 2-x ) surface-decorated nanoclusters, which mitigated Pt nanoparticle coarsening. Finally, analysis of the here-to-fore unknown catalyst structure as well as its performance and durability in a PEM fuel cell membrane electrode assembly (MEA) is discussed.

25 ENERGY STORAGE↗
DOE OSTI2026

Surface Charge Predicts the Presence of Cation Effects in Electrocatalysis

The identity of electrolyte cations has an important influence on the rates of many electrocatalytic reactions, but these effects are not always observed. Recently, we found that the surface charge of the catalyst, quantified by the potential of zero total charge (PZTC), is a useful heuristic for predicting when cation effects will be observed for the oxygen reduction reaction (ORR). Here, we demonstrate that this descriptor allows us to rationalize the observation or absence of cation effects across a range of conditions, reactions (the hydrogen evolution reaction, the ORR, methanol oxidation, ethylene glycol oxidation, glycerol oxidation, and glucose reduction) and metal surfaces (Pt, Pd, Ag, and Au). These results suggest that when the reaction’s operating potential is negative of the metal’s PZTC, electrolyte cations accumulate at the catalyst surface and influence reaction rates. As a result, when reactions occur positive of the PZTC, cation effects are not observed.

Cations↗
DOE OSTI2025

Unraveling Dimensional Tuning: From 2D to 3D in Covalent Organic Frameworks for Enhanced 2e – Oxygen Reduction Reaction

Covalent organic frameworks (COFs) with a two-dimensional (2D) topology have recently emerged as promising catalyst systems for the electrosynthesis of hydrogen peroxide (H 2 O 2 ) from oxygen (O 2 ). However, designing 2D catalysts to achieve higher H 2 O 2 selectivity presents a significant challenge because of the extensive layer stacking and the aggregated active sites located in the basal planes. It results in lower atom utilization, which requires attention. In this study, we present two functionally similar COFs: one with a 2D rhombus topology (2D@BT_TPA-COF) and another with a three-dimensional (3D) noninterpenetrated pts topology (3D@BT_TPA-COF). Both COFs were utilized for the 2e – oxygen reduction reaction (2e – ORR). Tunning the dimensionality from 2D to 3D resulted in an increase in H 2 O 2 selectivity from approximately ~56% to approximately ~96% (at 0.4 V) and a rise in the turnover frequency (TOF) from 0.05 to 0.08 s –1 at 0.3 V. Nonaggregated active site distribution over 3D topology, featuring higher active site exposure, provides better access to the O 2 /electrolyte and facilitates electron transfer leading to higher 2e – ORR activity and selectivity compared to the 2D counterpart.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Understanding the Stability of Manganese Chromium Antimonate Electrocatalysts through Multimodal In Situ and Operando Measurements

Herein, we utilize an on-line electrochemical flow cell coupled with an inductively coupled plasma-mass spectrometer (ICP-MS) to characterize the impact of composition and reactant gas on the multielement dissolution of Mn(-Cr)-Sb-O electrocatalysts. Compared to Mn 2 O 3 and Cr 2 O 3 oxides, we find that the antimonate framework stabilizes Mn at OER potentials and Cr at both ORR and OER potentials. Furthermore, dissolution of Mn and Cr from Mn(-Cr)-Sb-O is found to be driven by ORR reaction rate, with minimal dissolution under N 2 . We observe preferential dissolution of Cr totaling 13% over 10 minutes at 0.3, 0.6, and 0.9 V vs RHE, with only 1.5% loss of Mn, indicating an enrichment of Mn at the surface of the particles. Despite this asymmetric dissolution, in situ X-ray absorption spectroscopy (XAS) showed no measurable changes in the Mn K-edge at comparable potentials. This lack of change could suggest that modification to the Mn oxidation state in the surface layer is too small or that layer is too thin to be measured with the bulk XAS measurement. Lastly, on-line ICP-MS was used to assess the effects of applied potential, scan rate, and current of Mn-Cr-Sb-O during cyclic voltammetry and accelerated stress tests. With this deeper understanding of the interplay between oxygen reduction and dissolution, testing procedures were identified to maximize both activity and stability. This work highlights the use of multi-modal in situ characterization techniques in tandem to build a more complete model of stability and develop protocols for optimizing catalyst performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Regulating Catalytic Properties and Thermal Stability of Pt and PtCo Intermetallic Fuel-Cell Catalysts via Strong Coupling Effects between Single-Metal Site-Rich Carbon and Pt

Developing low platinum-group-metal (PGM) catalysts for the oxygen reduction reaction (ORR) in proton-exchange membrane fuel cells (PEMFCs) for heavy-duty vehicles (HDVs) remains a great challenge due to the highly demanded power density and long-term durability. Here, this work explores the possible synergistic effect between single Mn site-rich carbon (Mn SA -NC) and Pt nanoparticles, aiming to improve intrinsic activity and stability of PGM catalysts. Density functional theory (DFT) calculations predicted a strong coupling effect between Pt and MnN 4 sites in the carbon support, strengthening their interactions to immobilize Pt nanoparticles during the ORR. The adjacent MnN 4 sites weaken oxygen adsorption at Pt to enhance intrinsic activity. Well-dispersed Pt (2.1 nm) and ordered L1 2 -Pt 3 Co nanoparticles (3.3 nm) were retained on the Mn SA -NC support after indispensable high-temperature annealing up to 800 °C, suggesting enhanced thermal stability. Both PGM catalysts were thoroughly studied in membrane electrode assemblies (MEAs), showing compelling performance and durability. The Pt@Mn SA -NC catalyst achieved a mass activity (MA) of 0.63 A mg Pt –1 at 0.9 V iR-free and maintained 78% of its initial performance after a 30,000-cycle accelerated stress test (AST). The L1 2 -Pt 3 Co@Mn SA -NC catalyst accomplished a much higher MA of 0.91 A mg Pt –1 and a current density of 1.63 A cm –2 at 0.7 V under traditional light-duty vehicle (LDV) H 2 –air conditions (150 kPa abs and 0.10 mg Pt cm –2 ). Furthermore, the same catalyst in an HDV MEA (250 kPa abs and 0.20 mg Pt cm –2 ) delivered 1.75 A cm –2 at 0.7 V, only losing 18% performance after 90,000 cycles of the AST, demonstrating great potential to meet the DOE targets.

25 ENERGY STORAGE↗
DOE OSTI2024

Cooperative Atomically Dispersed Fe–N 4 and Sn–N x Moieties for Durable and More Active Oxygen Electroreduction in Fuel Cells

One grand challenge for deploying porous carbons with embedded metal–nitrogen–carbon (M–N–C) moieties as platinum group metal (PGM)-free electrocatalysts in proton-exchange membrane fuel cells is their fast degradation and inferior activity. Here, we report the modulation of the local environment at Fe–N 4 sites via the application of atomic Sn–N x sites for simultaneously improved durability and activity. We discovered that Sn–N x sites not only promote the formation of the more stable D2 FeN 4 C 10 sites but also invoke a unique D3 SnN x –Fe II N 4 site that is characterized by having atomically dispersed bridged Sn–N x and Fe–N 4 . This new D3 site exhibits significantly improved stability against demetalation and several times higher turnover frequency for the oxygen reduction reaction (ORR) due to the shift of the reaction pathway from a single-site associative mechanism to a dual-site dissociative mechanism with the adjacent Sn site facilitating a lower overpotential cleavage of the O–O bond. This mechanism bypasses the formation of the otherwise inevitable intermediate that is responsible for demetalation, where two hydroxyl intermediates bind to one Fe site. Lastly, a mesoporous Fe/Sn-PNC catalyst exhibits a positively shifted ORR half-wave potential and more than 50% lower peroxide formation. This, in combination with the stable D3 site and enriched D2 Fe sites, significantly enhanced the catalyst’s durability as demonstrated in membrane electrode assemblies using complementary accelerated durability testing protocols.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Sub-angstrom strain in high-entropy intermetallic boosts the oxygen reduction reaction in fuel cell cathodes

The strain effect of high-entropy intermetallic (HEI) catalysts on oxygen reduction reaction (ORR) performance remains largely unexplored, primarily due to the significant challenges associated with characterizing and calculating the intricate local coordination environments. Here, we design a nitrogen (N)-doped L1 0 -ordered PtCoNiFeCu intermetallic catalyst supported on Ketjenblack carbon (N-HEI/KB), and reveal the origin of the sub-angstrom strain in N-HEI and its impact on ORR performance by combining atomic-scale characterization and theoretical calculations. The synergistic interplay of the sub-angstrom strain, the pinning effect of metal-N bonds, and the high-entropy effect contribute to the competitive stability of N-HEI/KB catalysts, providing high current density of 1388 mA cm -2 at 0.7 V after 90,000 cycles even under harsh heavy-duty vehicle conditions. These findings broaden the avenues for designing high-performance high-entropy intermetallic cathode electrocatalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Spontaneous N 2 formation by a diruthenium complex enables electrocatalytic and aerobic oxidation of ammonia

The electrochemical conversion of ammonia to dinitrogen in a direct ammonia fuel cell (DAFC) is a necessary technology for the realization of a Nitrogen Economy. Previous efforts to catalyze this reaction with molecular complexes require the addition of exogenous oxidizing reagents or application of potentials greater than the thermodynamic potential for the oxygen reduction reaction (ORR) – the cathodic process of a DAFC. We report a stable metal–metal bonded diruthenium complex that spontaneously produces dinitrogen from ammonia under ambient conditions. The resulting reduced diruthenium material can be re-oxidized with oxygen for subsequent reactions with ammonia, demonstrating its ability to spontaneously promote both half reactions necessary for a DAFC. Here, the diruthenium complex also acts as a redox mediator for the electrocatalytic oxidation of ammonia to dinitrogen at potentials as low as –255 mV vs Fc 0/+ and operates below the ORR potential in alkaline conditions, thus achieving a thermodynamic viability relevant for the future development of DAFCs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Origins of enhanced oxygen reduction activity of transition metal nitrides

Transition metal nitride (TMN-) based materials have recently emerged as promising non-precious-metal-containing electrocatalysts for the oxygen reduction reaction (ORR) in alkaline media. However, the lack of fundamental understanding of the oxide surface has limited insights into structure–(re)activity relationships and rational catalyst design. Here, in this work, we demonstrate how a well-defined TMN can dictate/control the as-formed oxide surface and the resulting ORR electrocatalytic activity. Structural characterization of MnN nanocuboids revealed that an electrocatalytically active Mn 3 O 4 shell grew epitaxially on the MnN core, with an expansive strain along the [010] direction to the surface Mn 3 O 4 . The strained Mn 3 O 4 shell on the MnN core exhibited an intrinsic activity that was over 300% higher than that of pure Mn 3 O 4 . A combined electrochemical and computational investigation indicated/suggested that the enhancement probably originates from a more hydroxylated oxide surface resulting from the expansive strain. This work establishes a clear and definitive atomistic picture of the nitride/oxide interface and provides a comprehensive mechanistic understanding of the structure–reactivity relationship in TMNs, critical for other catalytic interfaces for different electrochemical processes.

electrocatalysis↗
DOE OSTI2022

Quantifying the electrochemical active site density of precious metal-free catalysts in situ in fuel cells

We report advances in the development of precious-group metal-free (PGM-free) catalysts for the oxygen reduction reaction (ORR) in fuel cell cathodes have produced active catalysts that reduce the performance gap to the incumbent Pt-based materials. However, utilization of state-of-the-art PGM-free catalysts for commercial applications is currently impeded by their relatively low durability. Methods designed to study catalyst degradation in the operation of fuel cells are therefore critical for understanding durability issues and, ultimately, their solutions. Here we report the use of Fourier-transform alternating current voltammetry as an electrochemical method for accurate quantification of the electrochemically active site density of PGM-free cathode catalysts, and to follow their degradation in situ during the operation of polymer electrolyte fuel cells. Using this method, we were able to quantify the electrochemical active site density, which will enable the elucidation of degradation mechanisms of PGM-free ORR catalysts in situ in fuel cells.

25 ENERGY STORAGE↗
DOE OSTI2022

Acid anion electrolyte effects on platinum for oxygen and hydrogen electrocatalysis

Platinum is an important material with applications in oxygen and hydrogen electrocatalysis. To better understand how its activity can be modulated through electrolyte effects in the double layer microenvironment, herein we investigate the effects of different acid anions on platinum for the oxygen reduction/evolution reaction (ORR/OER) and hydrogen evolution/oxidation reaction (HER/HOR) in pH 1 electrolytes. Experimentally, we see the ORR activity trend of HClO 4 > HNO 3 > H 2 SO 4 , and the OER activity trend of HClO 4 > HNO 3 ~ H 2 SO 4 . HER/HOR performance is similar across all three electrolytes. Notably, we demonstrate that ORR performance can be improved 4-fold in nitric acid compared to in sulfuric acid. Assessing the potential-dependent role of relative anion competitive adsorption with density functional theory, we calculate unfavorable adsorption on Pt(111) for all the anions at HER/HOR conditions while under ORR/OER conditions ClO$^{-}_{4}$ binds the weakest followed by NO$^{-}_{3}$ and SO$^{2-}_{4}$. Our combined experimental-theoretical work highlights the importance of understanding the role of anions across a large potential range and reveals nitrate-like electrolyte microenvironments as interesting possible sulfonate alternatives to mitigate the catalyst poisoning effects of polymer membranes/ionomers in electrochemical systems. These findings help inform rational design approaches to further enhance catalyst activity via microenvironment engineering.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Doping-modulated strain control of bifunctional electrocatalysis for rechargeable zinc–air batteries

Changes in the local atomic arrangement in a crystal caused by lattice-mismatch-induced strain can efficiently regulate the performance of electrocatalysts for zinc–air batteries (ZABs) in many manners, mainly due to modulated electronic structure configurations that affect the adsorption energies for oxygen-intermediates formed during oxygen reduction and evolution reactions (ORR and OER). However, the application of strain engineering in electrocatalysis has been limited by the strain relaxation caused by structural instability such as dissolution and destruction, leading to insufficient durability towards the ORR/OER. In this work, we propose a doping strategy to modulate the phase transition and formation of self-supported cobalt fluoride–sulfide (CoFS) nanoporous films using a low amount of copper (Cu) as a dopant. This well-defined Cu–CoFS heterostructure overcomes the obstacle of structural instability. Our study of the proposed Cu–CoFS also helps establish the structure–property relationship of strained electrocatalysts by unraveling the role of local strain in regulating the electronic structure of the catalyst. As a proof-of-concept, the Cu–CoFS electrocatalyst with doping-modulated strain exhibited superior onset potentials of 0.91 V and 1.49 V for the ORR and OER, respectively, surpassing commercial Pt/C@RuO 2 and benchmarking non-platinum group metal (non-PGM) catalysts. ZABs with the Cu–CoFS catalyst delivered excellent charge/discharge cycling performance with an extremely low voltage gap of 0.5 V at a current density of 10 mA cm –2 and successively 0.93 V at a high current density of 100 mA cm –2 and afforded an outstanding peak power density of 255 mW cm –2 .

25 ENERGY STORAGE↗