Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Nuclear graphite”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

A Comparison of the Irradiation Creep Behavior of Several Graphites

Graphite creep strain data from the irradiation creep capsule Advanced Graphite Creep-1 (AGC-1) are reported. This capsule was the first (prototype) of a series of five or six capsules planned as part of the AGC experiment, which was designed to fully characterize the effects of neutron irradiation and the radiation creep behavior of current nuclear graphite. The creep strain data and analysis are reported for the six graphite grades incorporated in the capsule. The AGC-1 capsule was irradiated in the Advanced Test Reactor at Idaho National Laboratory (INL) at approximately 700 C and to a peak dose of 7 dpa (displacements per atom). The specimen s final dose, temperature, and stress conditions have been reported by INL and were used during this analysis. The derived creep coefficients (K) were calculated for each grade and were found to compare well to literature data for the creep coefficient, even under the wide range of AGC-1 specimen temperatures. Comparisons were made between AGC-1 data and historical grade data for creep coefficients.

Graphite↗

Mechanical behavior analysis using small-size graphite disc compression testing with digital image correlation methods

The ASTM International Standard Test Method for Tensile Stress-Strain of Carbon and Graphite (ASTM C749) requires dog-bone shaped specimens. Unfortunately, specimen sizes required in ASTM C749 are much too large for irradiation within a test reactor and are incompatible with irradiation capsule volumes, molten salt degradation facilities, or oxidation apparatus. The ASTM International Standard Test Method for Tensile Strength Estimate by Disc Compression of Manufactured Graphite (ASTM D8289) was developed as an alternative that provides a means for testing tensile properties using smaller specimens when geometric constraints are present. However, the important stress–strain relation throughout the test loading history that could be recorded using ASTM C749 is lost by using ASTM D8289 because of the difficulties involved with using traditional strain gauges or extensometers on such a small specimen. In this work, a digital image correlation (DIC) method, which uses a full-field noncontact surface displacement measurement technique, was applied along with the ASTM D8289 splitting tensile test on eight small samples of graphite grade Mersen 2114 to track their deformation during compressive loading. Initial results showed that the DIC technique can measure the surface displacement/strain on these small (Ø6 × 3 mm) graphite specimens with high accuracy and good repeatability, indicating that the DIC technique, combined with the small-disc splitting tensile test in ASTM D8289, can capture the strain evolution in the test. In conclusion, further comparison of measured strains with analytical and numerical simulation results provides additional understanding of the mechanical behaviour of this nuclear graphite material in complex stress states.

36 MATERIALS SCIENCE↗

AGR-3/4 Irradiation Test Train Disassembly and Component Metrology First Look Report

The AGR-3/4 experiment was designed to study fission product transport within graphitic matrix material and nuclear-grade graphite. To this end, this experiment consisted of 12 capsules, each fueled with 4 compacts containing UCO TRISO particles as driver fuel and 20 UCO designed-to-fail (DTF) fuel particles in each compact. The DTF fuel was fabricated with a thin pyrocarbon layer which was intended to fail during irradiation and provide a source of fission products. These fission products could then migrate through the compact and into the surrounding concentric rings of graphitic matrix material and/or nuclear graphite. Through post-irradiation examination (PIE) of the rings (including physical sampling and gamma scanning) fission product concentration profiles within the rings can be determined. These data can be used to elucidate fission product transport parameters (e.g. diffusion coefficients within the test materials) which will be used to inform and refine models of fission product transport. After irradiation in the Advanced Test Reactor (ATR) had been completed in April 2014, the AGR-3/4 experiment was shipped to the Hot Fuel Examination Facility (HFEF) at the Materials and Fuels Complex (MFC) for inspection, disassembly, and metrology. The AGR-3/4 test train was received at MFC in two separate shipments between February and April 2015. Visual examinations of the test train exterior did not indicate dimensional distortion, and only two small discolored areas were observed at the bottom of Capsules 8 and 9. No corresponding discoloration was found on the inside of these capsules, however. Prior to disassembly, the two test train sections were subject to analysis via the Precision Gamma Scanner (PGS), which did not indicate that any gross fuel relocation had occurred. A series of specialized tools (including clamps, cutters, and drills) had been designed and fabricated in order to carry out test train disassembly and recovery of capsule components (graphite rings and fuel compacts). This equipment performed well for separating each capsule in the test train and extracting the capsule components. Only a few problems were encountered. In one case, the outermost ring (the sink ring) was cracked during removal of the capsule through tubes. Although the sink ring will be analyzed in order to obtain a mass balance of fission products in the experiment, these cracks do not pose a major concern because the sink ring will not be analyzed in detail to obtain the spatial distribution of fission products. In Capsules 4 and 5, the compacts could not be removed from the inner rings. Strategies for removing the compacts are being evaluated. Sampling the inner rings with the compacts in-place is also an option. Dimensional measurements were made on the compacts, inner rings, outer rings, and sink rings. The diameters of all compacts decreased by 0.5 to 2.0 %. Generally, the extent of diametric shrinkage increased linearly with increasing neutron fluence. Most compact lengths also decreased. Compact lengths decreased with increasing fluence, reaching maximum shrinkage of about 0.9 % at a fast fluence of 4.0x1025 n/m2 E > 0.18 MeV. Above this fluence, the extent of length shrinkage appeared to decrease with fluence, and two compacts from Capsule 7 were found to have slightly increased in length (< 0.1 %) after a fluence of 5.2x1025 n/m2.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Investigation of the Impact of TSL Data Libraries and Geometry Variations on the MSRE Benchmark

The increasing demand for green, low-carbon energy solutions has amplified the focus on advanced nuclear reactor technologies. Among these, Molten Salt Reactors (MSRs) have been spotlighted because of their special features. Historically, Oak Ridge National Laboratory (ORNL) started the Molten Salt Reactor Experiment (MSRE) in 1956. Later, ORNL and the University of California, Berkeley (UCB) jointly developed the MSRE benchmark. This was then reviewed by the International Reactor Physics Experiment Evaluation Project (IRPhEP) committee and added to their 2019 handbook. In the current study, the benchmark model was recreated via the Serpent code. The calculated effective multiplication factor was 1.02087 ± 0.00019, which gives a deviation of about 2000 pcm compared to the benchmark/experimental result. At North Carolina State University (NCSU), recent evaluations were conducted on thermal scattering cross sections for molten salt FLiBe and 20% porous nuclear graphite, anticipated for incorporation in the ENDF/B-VIII.1 library. The influences of these thermal scattering law (TSL) data and geometry changes on the multiplication factor were examined using the ENDF/B-VII.1 and ENDF/B-VIII.0 libraries. Introducing the TSL data for FLiBe and 20% porous graphite resulted in an effective multiplication factor of +270 pcm compared to the reference value obtained with ENDF/B-VII.1 in this study. The adjustment of the reactor vessel dimensions resulted in decrease of -448 pcm in the calculated effective multiplication factor.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

AGR-3/4 Irradiation Test Train Disassembly and Component Metrology First Look Report

The AGR-3/4 experiment was designed to study fission product transport within graphitic matrix material and nuclear-grade graphite. To this end, this experiment consisted of 12 capsules, each fueled with 4 compacts containing UCO TRISO particles as driver fuel and 20 UCO designed-to-fail (DTF) fuel particles in each compact. The DTF fuel was fabricated with a thin pyrocarbon layer which was intended to fail during irradiation and provide a source of fission products. These fission products could then migrate through the compact and into the surrounding concentric rings of graphitic matrix material and/or nuclear graphite. Through post-irradiation examination (PIE) of the rings (including physical sampling and gamma scanning) fission product concentration profiles within the rings can be determined. These data can be used to elucidate fission product transport parameters (e.g. diffusion coefficients within the test materials) which will be used to inform and refine models of fission product transport. After irradiation in the Advanced Test Reactor (ATR) had been completed in April 2014, the AGR-3/4 experiment was shipped to the Hot Fuel Examination Facility (HFEF) at the Materials and Fuels Complex (MFC) for inspection, disassembly, and metrology. The AGR-3/4 test train was received at MFC in two separate shipments between February and April 2015. Visual examinations of the test train exterior did not indicate dimensional distortion, and only two small discolored areas were observed at the bottom of Capsules 8 and 9. No corresponding discoloration was found on the inside of these capsules, however. Prior to disassembly, the two test train sections were subject to analysis via the Precision Gamma Scanner (PGS), which did not indicate that any gross fuel relocation had occurred. A series of specialized tools (including clamps, cutters, and drills) had been designed and fabricated in order to carry out test train disassembly and recovery of capsule components (graphite rings and fuel compacts). This equipment performed well for separating each capsule in the test train and extracting the capsule components. Only a few problems were encountered. In one case, the outermost ring (the sink ring) was cracked during removal of the capsule through tubes. Although the sink ring will be analyzed in order to obtain a mass balance of fission products in the experiment, these cracks do not pose a major concern because the sink ring will not be analyzed in detail to obtain the spatial distribution of fission products. In Capsules 4 and 5, the compacts could not be removed from the inner rings. Strategies for removing the compacts are being evaluated. Sampling the inner rings with the compacts in-place is also an option. Dimensional measurements were made on the compacts, inner rings, outer rings, and sink rings. The diameters of all compacts decreased by 0.5 to 2.0 %. Generally, the extent of diametric shrinkage increased linearly with increasing neutron fluence. Most compact lengths also decreased. Compact lengths decreased with increasing fluence, reaching maximum shrinkage of about 0.9 % at a fast fluence of 4.0x10 25 n/m 2 E > 0.18 MeV. Above this fluence, the extent of length shrinkage appeared to decrease with fluence, and two compacts from Capsule 7 were found to have slightly increased in length (< 0.1 %) after a fluence of 5.2x10 25 n/m 2 .

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Oxidation Behavior of Matrix Graphite and Its Effect on Compressive Strength

Matrix graphite (MG) with incompletely graphitized binder used in high-temperature gas-cooled reactors (HTGRs) is commonly suspected to exhibit lower oxidation resistance in air. In order to reveal the oxidation performance, the oxidation behavior of newly developed A3-3 MG at the temperature range from 500 to 950°C in air was studied and the effect of oxidation on the compressive strength of oxidized MG specimens was characterized. Results show that temperature has a significant influence on the oxidation behavior of MG. The transition temperature between Regimes I and II is ~700°C and the activation energy ( E a ) in Regime I is around 185 kJ/mol, a little lower than that of nuclear graphite, which indicates MG is more vulnerable to oxidation. Oxidation at 550°C causes more damage to compressive strength of MG than oxidation at 900°C. Comparing with the strength of pristine MG specimens, the rate of compressive strength loss is 77.3% after oxidation at 550°C and only 12.5% for oxidation at 900°C. Microstructure images of SEM and porosity measurement by Mercury Porosimetry indicate that the significant compressive strength loss of MG oxidized at 550°C may be attributed to both the uniform pore formation throughout the bulk and the preferential oxidation of the binder.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Development of mesopores in superfine grain graphite neutron-irradiated at high fluence

Microstructural changes induced by neutron irradiation of superfine grain graphite G347A (Tokai Carbon, Japan) were examined by nitrogen adsorption at 77K and by three microscopy techniques (SEM, TEM and FIB-SEM tomography). The specimens were irradiated at doses of up to 30 dpa, covering stages before and after the turnaround fluence at three temperatures (300, 450, 750 °C) of their irradiation envelope. The initial graphite densification at low fluences did not produce any detectable effect in the pore size range (<350 nm) measured by gas adsorption. However, graphite irradiated at high fluences, after turnaround, showed severe structural changes. At all three temperatures and high irradiation fluences, gas adsorption revealed significant increase of the volume of narrow mesopores (<5–20nm) and up to five times increase of BET surface area, both in linear relationship with the relative volume expansion. Analysis of microscopy images showed multiplication of fine macropores (>50 nm) at high irradiation fluences and more structural changes on multiple scales, from nanometers to microns. This work demonstrates the unique ability of gas adsorption techniques to analyze open pores with sizes between sub-nanometer and sub-micron in bulk nuclear graphite, with supporting microscopy results.

I. Contescu, Cristian↗

Development of mesopores in superfine grain graphite neutron-irradiated at high fluence

Microstructural changes induced by neutron irradiation of superfine grain graphite G347A (Tokai Carbon, Japan) were examined by nitrogen adsorption at 77 K and by three microscopy techniques (SEM, TEM and FIB-SEM tomography). The specimens were irradiated at doses of up to 30 dpa, covering stages before and after the turnaround fluence at three temperatures (300, 450, 750 °C) of their irradiation envelope. The initial graphite densification at low fluences did not produce any detectable effect in the pore size range (<350 nm) measured by gas adsorption. However, graphite irradiated at high fluences, after turnaround, showed severe structural changes. At all three temperatures and high irradiation fluences, gas adsorption revealed significant increase of the volume of narrow mesopores (<5–20 nm) and up to five times increase of BET surface area, both in linear relationship with the relative volume expansion. Analysis of microscopy images showed multiplication of fine macropores (>50 nm) at high irradiation fluences and more structural changes on multiple scales, from nanometers to microns. As a result, this work demonstrates the unique ability of gas adsorption techniques to analyze open pores with sizes between sub-nanometer and sub-micron in bulk nuclear graphite, with supporting microscopy results.

36 MATERIALS SCIENCE↗

Oxidation of Matrix Material in Helium with Varied Moisture Content

Exploration of the oxidation behavior of matrix material from tristructural-isotropic (TRISO) coated particle fuel elements in moisture environments provides critical data needed to predict the material’s response during off-normal accident scenarios. Near-representative, matrix-only samples were fabricated to facilitate oxidation testing in varied moisture concentrations. Oxidation testing was completed over a range of temperatures and oxidizing environments to obtain the relevant oxidation kinetics parameters and empirical oxidation rates necessary to better predict and understand matrix oxidation behavior at relevant conditions. The acquired oxidations rates were fit to established models for steam oxidation of nuclear graphite, and data were acquired following an established process. The data showed good agreement over conditions typical of the kinetic regime, and they showed a departure from the kinetic model fit at elevated temperatures and steam partial pressures in helium carrier gas. The departure was confirmed to be due to the experimental conditions being beyond the kinetic regime based on destructive analysis.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The importance of phonon spectrum measurements for accurate prediction of thermal scattering laws [Slides]

Although approximate phonon spectra (e.g. Debye model) are sufficient to reproduce integral quantities (e.g. total INS cross section) in reasonable agreement with the measured data, more accurate phonon spectra are needed to achieve agreement with the differential data. SANS component is essential for reproducing the total scattering cross section; this is the case for nanodiamonds and other materials where SANS components are present (such as porous materials like nuclear graphite). A format proposal for SANS data in ENDF or GNDS is needed. Therefore, differential (e.g. phonon spectrum) and integral (e.g. total cross section) measurements are necessary in the process of creating an ENDF evaluation. We have successfully developed a method by which ENDF evaluations can be directly compared to the relevant experimentally measured quantities. INS experiments at SNS, ILL, ISIS, and, in the future, ESS, as well as total cross section measurements at the VESUVIO instrument at ISIS, are accessible through user programs.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Experimental Investigation and CFD Analysis of Steam Ingress Accidents in HTGRs

This study focuses on the short-term phenomena due to steam ingress following an SG tube rupture accident in HTGRs, instead of covering a long-term scenario induced by a small amount of steam ingress during plant lifetime. Our ultimate goal is to better understand water/steam ingress accidents in HTGRs, where the Rankine cycle is adopted as the power conversion cycle. General Atomics’ 350 MWth Modular High Temperature Gas-cooled Reactor (MHTGR) was chosen as the prototypic reactor design. The models of steam nuclear graphite oxidation proposed in the literature are surveyed, and will be examined, validated or improved if needed. Furthermore, this study aims to develop and validate a predictive tool for steam ingress accidents. To measure the steam concentration evolution in an integral effect test (IET) facility, a tunable diode laser absorption spectroscopy (TDLAS) measurement system was developed. The TDLAS measuring system is a non-intrusive and non-perturbative diagnostic technique that can be used to measure the steam temperature and concentration at various conditions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Stored energy release in neutron irradiated silicon carbide

The purpose of this investigation is to experimentally quantify the stored energy release upon thermal annealing of previously irradiated high-purity silicon carbide (SiC.) Samples of highly-faulted polycrystalline CVD β-SiC and single crystal 6HSiC were irradiated in a mixed spectrum fission reactor near 60 °C in a fluence range from 5 × 10 23 to 2 × 10 26 n/m 2 (E > 0.1 MeV), or about 0.05–20 dpa, in order to quantify the stored energy release and correlate the release to the observed microscopic swelling, lattice dilation, and microstructure as observed through TEM. Within the fluence of this study the crystalline material was observed to swell to a remarkable extent, achieving 8.13% dilation, and then cross a threshold dose for amorphization at approximately 1 × 10 25 n/m 2 (E > 0.1 MeV) Once amorphized the material attains an as-amorphized swelling of 11.7% at this irradiation condition. Coincident with the extraordinary swelling obtained for the crystalline SiC, an equally impressive stored energy release of greater than 2500 J/g at the critical threshold for amorphization is inferred. As expected, following amorphization the stored energy in the structure diminishes, measured to be approximately 590 J/g. Generally, the findings of stored energy are consistent with existing theory, though the amount of stored energy given the large observed crystalline strain is remarkable. The overall conclusion of this work finds comparable stored energy in SiC to that of nuclear graphite, and similar to graphite, a stored energy release in excess of its specific heat in some irradiation conditions.

36 MATERIALS SCIENCE↗

Inverse problems in heterogeneous and fractured media using peridynamics

The following work presents an adjoint-based methodology for solving inverse problems in heterogeneous and fractured media using state-based peridynamics. We show that the inner product involving the peridynamic operators is self-adjoint. The proposed method is illustrated for several numerical examples with constant and spatially varying material parameters as well as in the context of fractures. We also present a framework for obtaining material parameters by integrating digital image correlation (DIC) with inverse analysis. This framework is demonstrated by evaluating the bulk and shear moduli for a sample of nuclear graphite using digital photographs taken during the experiment. The resulting measured values correspond well with other results reported in the literature. Lastly, we show that this framework can be used to determine the load state given observed measurements of a crack opening. Furthermore, this type of analysis has many applications in characterizing subsurface stress-state conditions given fracture patterns in cores of geologic material.

97 MATHEMATICS AND COMPUTING↗

Baseline Graphite Characterization: First Billet

The Next Generation Nuclear Plant Project Graphite Research and Development program is currently establishing the safe operating envelope of graphite core components for a very high temperature reactor design. To meet this goal, the program is generating the extensive amount of quantitative data necessary for predicting the behavior and operating performance of the available nuclear graphite grades. In order determine the in-service behavior of the graphite for the latest proposed designs, two main programs are underway. The first, the Advanced Graphite Creep (AGC) program, is a set of experiments that are designed to evaluate the irradiated properties and behavior of nuclear grade graphite over a large spectrum of temperatures, neutron fluences, and compressive loads. Despite the aggressive experimental matrix that comprises the set of AGC test runs, a limited amount of data can be generated based upon the availability of space within the Advanced Test Reactor and the geometric constraints placed on the AGC specimens that will be inserted. In order to supplement the AGC data set, the Baseline Graphite Characterization program will endeavor to provide supplemental data that will characterize the inherent property variability in nuclear-grade graphite without the testing constraints of the AGC program. This variability in properties is a natural artifact of graphite due to the geologic raw materials that are utilized in its production. This variability will be quantified not only within a single billet of as-produced graphite, but also from billets within a single lot, billets from different lots of the same grade, and across different billets of the numerous grades of nuclear graphite that are presently available. The thorough understanding of this variability will provide added detail to the irradiated property data, and provide a more thorough understanding of the behavior of graphite that will be used in reactor design and licensing. This report covers the development of the Baseline Graphite Characterization program from a testing and data collection standpoint through the completion of characterization on the first billet of nuclear-grade graphite. This data set is the starting point for all future evaluations and comparisons of material properties.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Testing of Small Graphite Samples for Nuclear Qualification

Accurately determining the mechanical properties of small irradiated samples is crucial to predicting the behavior of the overal irradiated graphite components within a Very High Temperature Reactor. The sample size allowed in a material test reactor, however, is limited, and this poses some difficulties with respect to mechanical testing. In the case of graphite with a larger grain size, a small sample may exhibit characteristics not representative of the bulk material, leading to inaccuracies in the data. A study to determine a potential size effect on the tensile strength was pursued under the Next Generation Nuclear Plant program. It focuses first on optimizing the tensile testing procedure identified in the American Society for Testing and Materials (ASTM) Standard C 781-08. Once the testing procedure was verified, a size effect was assessed by gradually reducing the diameter of the specimens. By monitoring the material response, a size effect was successfully identified.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

AGC-1 Pre-Irradiation Data Report Status

The Next Generation Nuclear Plant (NGNP) Graphite R&D program is currently measuring irradiated material property changes in several grades of nuclear graphite for predicting their behavior and operating performance within the core of new Very High Temperature Reactor (VHTR) designs. The Advanced Graphite Creep (AGC) experiment consisting of six irradiation capsules will generate this irradiated graphite performance data for NGNP reactor operating conditions. All samples in the experiment will be fully characterized before irradiation, irradiated in the Advanced Test Reactor (ATR), and then re-examined to determine the irradiation induced changes to key materials properties in the different graphite grades. The information generated during the AGC experiment will be utilized for NRC licensing of NGNP reactor designs, shared with international collaborators in the Generation IV Information Forum (GIF), and eventually utilized in ASME design code for graphite nuclear applications. This status report will describe the process the NGNP Graphite R&D program has developed to record the AGC1 pre-irradiation examination data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Perspective on “code qualifying” new graphite grades for use in advanced nuclear reactors*

The American Society of Mechanical Engineers (ASME) publishes the Boiler and Pressure Vessel (BPV) Code, which include guidance for the safe development, construction, and operation of boilers and pressure vessels. ASME BPV Code Section III “Rules for Construction of Nuclear Facility Components” Division 5 focuses on “High Temperature Reactors”. Subsection HH, subpart A lists the different materials properties that are to be measured and how those properties change due to different environmental conditions (oxidation and irradiation damage) for a graphite to be accepted for use in a high temperature reactor core (i.e., “Code Qualified”). Currently there are no nuclear graphite grades that are “Code Qualified” (i.e., a reactor designer can select a graphite grade and build their reactor without any additional testing), which is due in part to development of new graphite grades in the last 20 years and the lack of comprehensive programs needed to produce the data for the code cases. This perspective is going to discuss the requirements, as called out in the ASME BPV Code, that are necessary to “code qualify” a nuclear graphite grade but will primarily focus on the practical and technical challenges associated with irradiation-induced property changes and how to address these to assist with getting graphite ready for use in advanced nuclear reactors. These same technical challenges can be expected to arise for other materials being developed for advanced reactor concepts.

advanced nuclear reactors↗