Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microstructural properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Understanding the Effect of Electrochemical Properties and Microstructure on the Microgalvanic Corrosion of Mg Alloys via Phase-Field Simulations

In this work, we apply a phase-field model to gain insights into the corrosion behavior of Mg alloys. Specifically, we study the effect of electrochemical properties of the materials and their environment and the spatial distribution of second phases in a magnesium alloy. To this end, we perform sensitivity analyses in which we separately vary the exchange current density and corrosion potential of the second phase, as well as the electrolyte conductivity. We describe the effects of these parameters on the corrosion current and the resulting corrosion-front morphology. We also confirm that the ratio between the Wagner length, calculated for the anodic phase, and the initial width of the anodic domain is a good predictor of the morphological characteristic of the corroding surface. In addition, we examine the effect of the microstructure on the corrosion behavior in both 2D and 3D systems by varying the shape, size, and distribution of the second-phase regions. Our findings provide insights into the influence of the two-phase microstructure on the corrosion behavior in a magnesium alloy.

Electrochemistry↗
DOE OSTI2018

Experimental and Modeling Studies on the Microstructures and Properties of Oxidized Aluminum Nitride Ceramic Substrates

Oxidation of aluminum nitride (AlN) ceramic substrates doped with 2 wt.% Y{sub 2}O{sub 3} was performed in air at temperatures ranging from 1000 to 1300 °C for various lengths of time. Microstructure, bending strength, and thermal conductivity of the oxidized AlN substrates were studied experimentally and also via mathematical models. The results show that the oxide layer formed on the AlN substrates is composed of α-Al{sub 2}O{sub 3} nanocrystallines and interconnected micropores. Longitudinal and transverse cracks are induced in the oxide layer under tensile and shear stresses, respectively. Intergranular oxidation of the AlN grains close to the oxide layer/AlN interface also occurs, leading to widening and cracking of the AlN grain boundaries. These processes result in the monotonous degradation of bending strength and thermal conductivity of the oxidized AlN substrates. Two mathematic models concerning these properties of the oxidized AlN substrates versus the oxide layer thickness were put forward. They fit well with the experimental results.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effects of CeO{sub 2} on the Microstructure and Properties of Laser Cladding 316L Coating

Laser cladding was used to distribute a CeO{sub 2}-modified 316L powder coating onto a 316L stainless steel surface. The cladding layer phase composition was evaluated through x-ray diffraction. An analysis of the microstructure was conducted using an optical microscope and scanning electron microscope, while the micro-hardness was measured using a tester. The coating corrosion behavior in response to 3.5% NaCl solution was analyzed by polarization curves and electrochemical impedance spectroscopy. Finally, the overall performance of coatings with different CeO{sub 2} concentrations, 1, 2, and 3%, was compared. Results showed that adding CeO{sub 2} significantly refined the grains, reduced the coating porosity, and effectively limited the appearance of local corrosion. Also, additive CeO{sub 2} shifted the coating’s electrode potential in a positive direction, minimizing the current density of corrosion, creating a stable passivation film, and improving the coating’s corrosion resistance. The coating performance (hardness and corrosion behavior) was optimal when 2% CeO{sub 2} was employed as the powder mass.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Structural studies of zirconium doped Ba{sub 0.70}Sr{sub 0.30}TiO{sub 3} lead free ferroelectric thin films

Ba{sub 0.7}Sr{sub 0.3}(Zr{sub x}Ti{sub 1-x})O{sub 3}(BSZT, x=0,0.05,0.10,0.15,0.20) thin films were prepared by using sol gel method. Structural and microstructural properties were studied by using XRD, Raman Spectroscopy and atomic force microscopy (AFM) respectively. XRD and Raman Spectroscopy show the presence of tetragonal phase in multilayer BSZT thin film. The experimental results demonstrate that structural and microstructural properties of BSZT thin film were significantly dependent on variation of Zr content.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2015

Microstructure and magnetic properties of (001) textured L1(0) FePt films on amorphous glass substrate

L1(0) FePt thin films with an island-like morphology and magnetic perpendicular anisotropy were grown at low temperature (300 < T-dep< 375 degrees C) by magnetron sputtering on Hoya glass substrates using a 30-nm thick Cr (2 0 0) underlayer. An MgO buffer layer with a thickness of 2 nm was used to inhibit the diffusion from the Cr underlayer and promote the growth of (0 0 1) oriented L1(0) FePt films by inducing an in-plane lattice distortion. By varying the substrate temperature and the Ar sputter pressure (3.5 < P-Ar< 15 mTorr) during the deposition, the degree of chemical order, the microstructure and the magnetic properties were tuned and the best properties in term of squareness ratio (M-r/M-s similar to 0.95) and coercive field (H-c similar to 14 kOe) were observed for films deposited at T-dep = 350 degrees C and P-Ar= 5 mTorr, due to the appearance of a tensile strain, which favors the perpendicular anisotropy. The analysis of the angular dependence of remanent magnetization curves on the optimized sample suggests that the magnetization reversal is highly incoherent due to the inter-island interactions. Our results provide useful information on the low temperature growth of FePt films with perpendicular anisotropy onto glass substrates, which are relevant for a variety of technological applications, such as magnetic recording and spintronic devices. (C) 2015 Elsevier B.V. All rights reserved.

Speliotis, T↗
DOE OSTI2015

Microstructures and Properties of Medium Manganese Sheet Steels - Strategies and Opportunities

Medium manganese steels, with 3 to 10 wt pct Mn, have been shown to be capable of being thermally-processed to produce sheet products with a variety of strength-ductility combinations and thus are receiving considerable attention as candidates for 3rd generation advanced high strength steels (3GAHSS). The steels typically contain refined microstructures with characteristic microstructural dimensions of 1 to 2 µm and consist of significant amounts of retained austenite in a fine grained ferritic matrix. Strategies for development of medium manganese steels are reviewed and results of recent property predictions based on composite modeling are presented. The importance of controlling austenite stability is illustrated with data on medium Mn (7 and 10 wt pct.), low carbon (0.1 and 0.15 wt pct) steels. Important forming variables (strain, strain rate, and temperature) are discussed, along with a consideration of yield point elongation, present in many medium Mn steels.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructure and Properties of the Al-27Si/Cu/Al-50Si Joint Brazed by the Partial Transient Liquid Phase Bonding

Al-27Si and Al-50Si were brazed by using a thin Cu interlayer. The metallurgical bonding without obvious defects is achieved, and a wide brazing seam consisting of fine eutectic structures and coarse Si particles is formed in the Al-27Si/Cu/Al-50Si joint. The deposition of Si element in the liquid phases during solidification results in the formation of the larger Si particles and ultra-small Si particles in the brazing seam. The shear strength of the joint reaches 63 MPa.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Nano/ultrafine grained austenitic stainless steel through the formation and reversion of deformation-induced martensite: Mechanisms, microstructures, mechanical properties, and TRIP effect

A comprehensive study was carried out on the strain-induced martensitic transformation, its reversion to austenite, the resultant grain refinement, and the enhancement of strength and strain-hardening ability through the transformation-induced plasticity (TRIP) effect in a commercial austenitic 304L stainless steel with emphasis on the mechanisms and the microstructural evolution. A straightforward magnetic measurement device, which is based on the measurement of the saturation magnetization, for evaluating the amount of strain-induced martensite after cold rolling and reversion annealing in metastable austenitic stainless steels was used, which its results were in good consistency with those of the X-ray diffraction (XRD) method. A new parameter called the effective reduction in thickness was introduced, which corresponds to the reasonable upper bound on the obtainable martensite fraction based on the saturation in the martensitic transformation. By means of thermodynamics calculations, the reversion mechanisms were estimated and subsequently validated by experimental results. The signs of thermal martensitic transformation at cooling stage after reversion at 850 °C were found, which was attributed to the rise in the martensite start temperature due to the carbide precipitation. After the reversion treatment, the average grain sizes were around 500 nm and the nanometric grains of the size of ~ 65 nm were also detected. The intense grain refinement led to the enhanced mechanical properties and observation of the change in the work-hardening capacity and TRIP effect behavior. A practical map as a guidance for grain refining and characterizing the stability against grain growth was proposed, which shows the limitation of the reversion mechanism for refinement of grain size. - Graphical abstract: Display Omitted - Highlights: • Nano/ultrafine grained austenitic stainless steel through martensite treatment • A parameter descriptive of a reasonable upper bound on the obtainable martensite • Characterization of martensite by virtue of a new developed magnetic device • Investigation of mechanical properties and TRIP effect and the effect of grain size.

36 MATERIALS SCIENCE↗
DOE OSTI2018

The influence of power spinning and annealing temperature on microstructures and properties of Cu-Sn alloy

Highlights: • The strengthening effect of power spinning is mainly achieved by strengthening fine grains and dislocations. • Twins formed by the aggregation and overlapping of stacking faults grow and widen • In power spinning of Cu-Sn alloy, plastic deformation is primarily powered by dislocation sliding. - Abstract: Electron back scatter diffraction pattern (EBSD), metallographic microscope (OM) and transmission electron microscope (TEM) are used to analyze the microstructural state of the Cu-Sn alloy before and after power spinning and annealing. The results show that after power spinning, the α phase grains are refined and gradually evolve into small and fine α{sub II} and deformed α{sub III} crystal grains, with an average grain size of about 2.2 μm. Work hardening results in massive network-like subgrain boundaries distributed in power spinning microstructure. Annealing at 400 °C contributes to the formation of dislocation cells and stacking faults, and high-angle grain boundaries (HABS) start to migrate and slide. After the formation of less defective equiaxed grains at 500 °C, twins continue to grow and widen based through continuous accumulation of stacking faults. Further testing of mechanical properties reveals that power spinning is conducive to the improvement of mechanical properties of Cu-Sn alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2013

Exhaust Gas Recirculation Cooler Fouling in Diesel Applications: Fundamental Studies Deposit Properties and Microstructure

This paper reports on the results of experimental efforts aimed at improving the understanding of the mechanisms and conditions at play in the fouling of EGR coolers. An experimental apparatus was constructed to utilize simplified surrogate heat exchanger tubes in lieu of full-size heat exchangers. The use of these surrogate tubes allowed removal of the tubes after exposure to engine exhaust for study of the deposit layer and its properties. The exhaust used for fouling the surrogate tubes was produced using a modern medium-duty diesel engine fueled with both ultra-low sulfur diesel and biodiesel blends. At long exposure times, no significant difference in the fouling rate was observed between fuel types and HC levels. Surface coatings for the tubes were also evaluated to determine their impact on deposit growth. No surface treatment or coating produced a reduction in the fouling rate or any evidence of deposit removal. In addition, microstructural analysis of the fouling layers was performed using optical and electron microscopy in order to better understand the deposition mechanism. The experimental results are consistent with thermophoretic deposition for deposit formation, and van der Waals attraction between the deposit surface and exhaust-borne particulate.

EGR↗
DOE OSTI2023

Frontal Polymerization of Stereoisomers: Distinct Microstructures and Properties in Endo- and Exo- Dicyclopentadiene Thermosets

This study explores the relationship between monomer stereochemistry and the materials properties of thermosets generated by frontal ring-opening metathesis polymerization (FROMP). The exo- and endo-stereoisomers of dicyclopentadiene (DCPD) undergo rapid FROMP to fabricate robust thermosets within seconds. The exo-isomer provides significant benefits compared to the commonplace endo-DCPD resins; exo-DCPD supports faster fronts (≈3 times faster) than the endo-analogue and is an easier-to-handle liquid at room temperature. This work is among the first to explore the materials properties of p(exo-DCPD) thermosets. Here, we demonstrate a significant decrease in T g for products derived from exo-DCPD, despite having a similar rubbery plateau compared to p(endo-DCPD). Soluble oligomers were synthesized as models to probe the microstructural features affected by the monomer stereochemistry. Interestingly, hydrogenated oligomers of endo-DCPD exhibit slight differences in stereoregularity compared to their exo-counterparts. Finally, we incorporated a bisnorbornenyl cross-linker in exo-DCPD resins to boost the polymer T g , while also maintaining fronts that propagate faster than endo-DCPD.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2018

Effect of Deep Cryogenic Treatment on Mechanical Properties and Microstructure of the Tool Steel CR7V for Hot Stamping

To solve the failure problem of hot stamping tool, the CR7V steel was deep cryogenically treated at different dwelling times with multiple tempering. The hardness, impact toughness and wear resistance of the CR7V steel were examined, and the effects of deep cryogenic treatment on the microstructure of the CR7V steel were studied by means of optical microscope, scanning electron microscope and energy-dispersive spectroscopy. The results show that deep cryogenic treatment has little effect on the hardness of the tempered CR7V steel, but improves its impact toughness and wear resistance. The improvement in mechanical properties is a result of the combination of dissolution of large carbide particles, formation of small-sized and uniformly distributed carbide particles and fine tempered martensite structure. The cryogenic treatment is optimized as follows: vacuum gas quenching, deep cryogenic treatment at − 196 °C for 6 h and triple tempering at 560 °C for 2 h, which improves the wear resistance by 68% and the impact toughness by 58% compared to the conventional heat treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Specific Features of the Microstructure and Properties of Multielement Nitride Coatings Based on TiZrNbAlYCr

Multicomponent nanostructured coatings based on (TiZrNbAlYCr)N with a hardness as high as 47 GPa were obtained by cathodic arc deposition. The effect of partial nitrogen pressure P{sub N} (with constant bias potential U{sub b} =–200 V applied to the substrate) on the phase-composition variation, the size of crystallites, and their relation to the microstructure and hardness was investigated. An increase in the nitrogen pressure resulted in the formation of two phases with characteristic BCC (the lattice period is 0.342 nm) and FCC lattices with averaged nanocrystallite sizes of 15 and 2 nm. At a high pressure of 0.5 Pa, crystallites in the FCC phase with a lattice period of 0.437 nm grew in size to ~7 nm. The hardness of deposited coatings with larger (3.5 nm) FCC-phase crystallites and smaller (7 nm) BCC-phase crystallites was enhanced considerably.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2019

Effect of Chemical Composition on the Microstructure and Properties of the Ag-Ga-Ge Alloys

This study presents a comparison of thermodynamically calculated phase compositions of Ag-Ga-Ge alloys at fixed temperatures with phase analysis results of alloys annealed at respective temperatures. Three isothermal sections of the Ag-Ga-Ge system at 25, 100 and 300 °C have been extrapolated using optimized thermodynamic parameters from the literature. An experimental analysis of the microstructure was carried out using optical microscopy, scanning electron microscopy and energy-dispersive spectrometry. Results obtained by x-ray powder diffraction methods (identified phases and lattice parameters) were compared with the results of the predicted phase equilibria. Good overall agreement between experimental and calculated values was obtained. The Brinell hardness and electrical conductivity of selected alloys were measured and obtained results were analyzed with respect to their overall compositions and phase constituents.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Target Configuration Effect on Microstructures and Properties of Vertically Aligned Nanocomposites

Vertically aligned nanocomposites (VANs) are unique thin films with vertical nanostructures embedded in a matrix material, allowing for the integration of two distinct materials. These nanocomposites offer novel combined physical properties, such as nanocomposite-based multiferroics and strongly coupled physical properties, such as magneto-optic coupling. Much work has been conducted in exploring different two-phase combinations and various processing conditions to achieve novel tunable properties that cannot be obtained by any single-phase material alone. Here, in this work, the target configuration effects are explored for the growth of LaFeO 3 –CoNi 2 O 4 VANs. Both mixed and pie-shaped targets are utilized to compare the target configuration effects on the phase separation, morphology tuning, and their resulting physical properties, including optical and magnetic properties. This work suggests that the target configuration is another important parameter for achieving the desired VAN morphology and can be used to design different two-phase VANs with tailorable properties.

36 MATERIALS SCIENCE↗
DOE OSTI2013

MECHANICAL PROPERTIES AND MICROSTRUCTURAL CHARACTERIZATION OF A MULTILAYERED MULTIPASS FRICTION STIR WELD IN STEEL

Multilayered multipass friction stir welding (MM-FSW) makes it possible to use FSW to fabricate thick-section structures. In this work, MM-FSW was demonstrated on a high strength low alloy steel; ASTM A572 Grade 50. Three steel plates with thicknesses of 0.18", 0.18", 0.24" respectively were stacked and friction stir welded together to form a 0.6" thick welded structure. The welded plate was sectioned into rectangular bars transverse to the weld direction for tensile testing to evaluate mechanical properties. Digital image correlation (DIC) was employed to map the local strain fields during tensile testing. The initial failure was found to occur simultaneously at the bottom and middle layers away from the weld zone. The top layer failed last in the base metal. The failure locations were consistent among different samples tested. Also, Charpy V-notch impact tests were conducted for weld metal, heat affected zone, and the base metal at each layer as a function of temperature. The weld microstructures were characterized using optical and electron microscopy and micro-hardness mapping.

Lim, Yong Chae↗
DOE OSTI2017

Effect of Laser Shock Peening on the Microstructures and Properties of Oxide-Dispersion-Strengthened Austenitic Steels

Oxide-dispersion-strengthened (ODS) austenitic steels are promising materials for next-generation fossil and nuclear energy systems. In this study, laser shock peening (LSP) has been applied to ODS 304 austenitic steels, during which a high density of dislocations, stacking faults, and deformation twins are generated in the near surface of the material due to the interaction of laser-driven shock waves and the austenitic steel matrix. The dispersion particles impede the propagation of dislocations. The compressive residual stress generated by LSP increases with successive LSP scans and decreases along the depth, with a maximum value of -369MPa. The hardness on the surface can be improved by 12% using LSP. In situ transmission electron microscopy (TEM) irradiation studies reveal that dislocations and incoherent twin boundaries induced by LSP serve as effective sinks to annihilate irradiation defects. Furthermore, these findings suggest that LSP can improve the mechanical properties and irradiation resistance of ODS austenitic steels in nuclear reactor environments.

36 MATERIALS SCIENCE↗