Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Membrane systems”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Hydrogen production from full-strength corn stover fermentation effluent in single-chamber replaceable-cathode microbial electrolysis cells

Lignocellulosic residual biomass generated by the agricultural sector is an abundant feedstock for biohydrogen production via dark fermentation. However, this process is intrinsically inefficient, converting only ~30% of the reductant energy into H2 and leaving substantial amounts of reduced byproducts. These byproducts, mostly found in the fermentation effluents, can be further valorized in microbial electrolysis cells (MECs) to enhance the overall H2 recovery. However, current MEC configurations are typically dual- or single-chamber systems, yet both suffer from key inefficiencies. Dual-chamber systems rely on proton exchange membranes that are costly and prone to rapid biofouling, whereas single-chamber, membraneless systems are limited by reduced productivity due to H2 recycling and methanogenic consumption In this study, three single-chamber, 50-mL replaceable-cathode microbial electrolysis cells (RC-MECs) were 3D-printed and equipped with a physical separator to isolate anode and cathode compartments and limit H2 migration. Full-strength milled corn stover (MCS) fermentation effluent (COD of ~23.8 g-COD/L) was treated in fed-batch mode over two operational periods spanning 21 (Run 1) and 80 (Run 2) days. The RC-MECs exhibited comparable performance in both runs: after biofilm maturation, current densities exceeded 100 A/m²_cathode, COD removal reached up to 43%. Notably, extended RC-MECs operation led to a substantial methanogenic activity with the CH4 fraction in the cathode gas increasing to as high as 80% of the total biogas. Additions of a methanogenesis inhibitor 2-bromoethanesulfonate (2-BES) produced transient increases in hydrogen yields (11.51 and 5.12 L-H2/L_reactor/day in Runs 1 and 2, respectively); however, sustained 2-BES addition in subsequent cycles reduced total biogas production, decreased COD removal, and led to volatile fatty acid accumulation. Overall, single-chamber MECs can treat high-strength dark fermentation effluents while improving H2 recovery, but methanogenesis remains a key bottleneck, and complete long-term inhibition may be operationally unsustainable.

Hydrogen Production↗
DOE OSTI2023

EXPERIMENTAL AND MODELING STUDY OF MOLECULAR TRANSPORT PHENOMENA IN COMPLEX LIQUID MIXTURES USING COVALENT ORGANIC FRAMEWORK MEMBRANES

Currently, 10-15% of the world’s energy is consumed by chemical separations, and more than 80% of that is used to purify organic liquids and recover rare earth elements and critical minerals. Membrane nanofiltration presents an energy-efficient, cost-effective, and eco-friendly alternative to current separation technologies. These complex liquid environments require high- performance, chemically-resistant membrane materials. Recently discovered Covalent Organic Frameworks (COFs) possess desirable properties as membrane materials for complex liquid separations. COFs are highly crystalline, chemically and thermally stable, with tunable size and charge. COFs, especially two-dimensional highly crystalline COFs, possess narrow pore-size distribution and controlled porous structures. Two-dimensional COFs are also resistant to swelling, another feature beneficial in complex liquid separations. Molecular interactions in complex liquid systems often dictate final membrane performance, resulting in a discrepancy between designed and apparent COF properties. Understanding and resolving this discrepancy is critical in utilizing COF membranes as a viable alternative to energy-intensive separations. The primary objective of this thesis was to use a commercially available COF TpPa-1 as a platform to investigate how mixed solvent environment affects COF membrane performance via experimental and molecular modeling studies. Specifically, the effects of solution pH, solvent- solvent-solute interactions in mixed solvents, and COF chemistry were carefully examined on apparent TpPa-1 pore size and permeability and targeted solute rejection of COF membranes for neat and mixed solvents. Experimental COF filtration performance was compared and corroborated with modeling predication. Findings from this study will provide guidance for future COF design, synthesis, and desired functional COF membrane performance.

Barnes, Anastasia↗
DOE OSTI2023

Microelectrode Arrays Measure Blocking of Voltage-Gated Calcium Ion Channels on Supported Lipid Bilayers Derived from Primary Neurons

Drug studies targeting neuronal ion channels are crucial to understand neuronal function and develop therapies for neurological diseases. The traditional method to study neuronal ion-channel activities heavily relies on the whole-cell patch clamp as the industry standard. However, this technique is both technically challenging and labour-intensive, while involving the complexity of keeping cells alive with low throughput. Therefore, the shortcomings are limiting the efficiency of ion-channel-related neuroscience research and drug testing. Here, this work reports a new system of integrating neuron membranes with organic microelectrode arrays (OMEAs) for ion-channel-related drug studies. This work demonstrates that the supported lipid bilayers (SLBs) derived from both neuron-like (neuroblastoma) cells and primary neurons are integrated with OMEAs for the first time. The increased expression of voltage-gated calcium (CaV) ion channels on differentiated SH-SY5Y SLBs compared to non-differentiated ones is sensed electrically. Also, dose-response of the CaV ion-channel blocking effect on primary cortical neuronal SLBs from rats is monitored. The dose range causing ion channel blocking is comparable to literature. This system overcomes the major challenges from traditional methods (e.g., patch clamp) and showcases an easy-to-test, rapid, ultra-sensitive, cell-free, and high-throughput platform to monitor dose-dependent ion-channel blocking effects on native neuronal membranes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Ionically Active MXene Nanopore Actuators

Reversible electrochemical intercalation of cations into the interlayer space of 2D materials induces tunable physical and chemical properties in them. In MXenes, a large class of recently developed 2D carbides and nitrides, low intercalation energy, high storage capacitance, and reversible intercalation of various cations have led to their improved performance in sensing and energy storage applications. In this work, a coupled nanopore-actuator system where an ultrathin free-standing MXene film serves as a nanopore support membrane and ionically active actuator is reported. In this system, the contactless MXene membrane in the electric field affects the cation movement in the field through their (de)intercalation between individual MXene flakes. This results in reversible swelling and contraction of the membrane monitored by ionic conductance through the nanopore. This unique nanopore coupled to a mechanical actuation system could provide new insights into designing single-molecule biosensing platforms at the nanoscale.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Conducting thermal energy to the membrane/water interface for the enhanced desalination of hypersaline brines using membrane distillation

Membrane distillation (MD) is a membrane-based thermal desalination process capable of treating hypersaline brines. Standard MD systems rely on preheating the feed to drive the desalination process. However, relying on the feed to carry thermal energy is limited by a decline of the thermal driving force as the water moves across the membrane, and temperature polarization. In contrast, supplying heat directly into the feed channel, either through the membrane or other channel surfaces, has the potential of minimizing temperature polarization, increasing single-pass water recoveries, and decreasing the number of heat exchangers in the system. When solar thermal energy can be utilized, particularly if the solar heat is optimally delivered to enhance water evaporation and process performance, MD processes can potentially be improved in terms of energy efficiency, environmental sustainability, or operating costs. Here we describe an MD process using layered composite membranes that include a high-thermal-conductivity layer for supplying heat directly to the membrane-water interface and the flow channel. Here, the MD system showed stable performance with water flux up to 9 L/m 2 /hr, and salt rejection >99.9% over hours of desalinating hypersaline feed (100 g/L NaCl). In addition to bench-scale system, we developed a computational fluid dynamics model that successfully described the transport phenomena in the system.

42 ENGINEERING↗
DOE OSTI2025

Comprehensive techno-economic and life cycle greenhouse gases analysis of green ammonia production utilizing PV and wind energy: Jordan as a case study

Ammonia (NH 3 ) has emerged as a critical player in the global energy transition due to its potential as a low-carbon fuel. Conventional ammonia production methods, primarily through steam methane reforming, are significant contributors to global CO 2 emissions. This study investigates the potential of green ammonia production in Jordan by leveraging the country's abundant solar photovoltaic and wind energy resources. A comprehensive techno-economic and life cycle greenhouse gas analysis was conducted to compare green ammonia production with conventional grey and blue ammonia pathways. Here, the study utilized spatial mapping to assess renewable energy capacity factors across Jordan and optimized the integration of hybrid PV/wind systems with proton exchange membrane (PEM) electrolyzers. The results indicate that the levelized cost of green ammonia (LCOA) in Jordan varies between 900 USD/kg NH 3 and 2500 USD/kg NH 3 which is significantly higher than grey ammonia (similar to 360 USD/kg NH 3 ). Nevertheless, the carbon intensity of green ammonia production (between 0.1 kg CO 2eq /kg NH 3 and 0.5 kg CO 2eq /kg NH 3 ) is much lower than the grey ammonia (1.8 kg CO 2eq /kg NH 3 ). Finally, the results indicate that considering future reductions in capital costs and advancement in renewable energy systems and PEM electrolyzers as well as the ability to sell the co-product O 2 can reduce the LCOA by up to 92 % and make it competitive with grey ammonia.

Green Ammonia↗
DOE OSTI2026

Public Reference Data for Megawatt-Scale Hydrogen Electrolysis - NLR Historical Wind

The U.S. Department of Energy and the National Laboratory of the Rockies (NLR) demonstrate hydrogen electrolysis from variable sources, hydrogen compression and storage, and hydrogen fuel cell power production using megawatt-scale equipment at NLR’s Flatirons Campus as part of the Advanced Research on Integrated Energy Systems (ARIES) initiative. This dataset represents part of that effort and is intended for academic, national laboratory, industrial, and other stakeholders to plan, design, and validate models of megawatt-scale hydrogen technologies and diverse energy infrastructure nationwide. These data provide a baseline for how existing hydrogen electrolysis technologies perform when coupled with various energy technologies. Future datasets will demonstrate how existing hydrogen fuel cell technologies can provide controllable, dispatchable, and variable power output for artificial intelligence (AI) data centers and other variable loads. This dataset entry describes hydrogen production by conducting a statistical analysis of historical wind data over a five-year period (2020-2025) from a single 1.5MW turbine manufactured by General Electric (GE) located at NLR’s Flatirons Campus, to generate an experimental test profile that was deployed on a 1.25-MW proton exchange membrane type MC250 electrolyzer system manufactured by Nel Hydrogen . [1] While the electrolyzer balance-of-plant supports up to 2.5 MW of electrolysis, NLR only has a single 1.25-MW electrolysis stack. The historical wind data provided several metrics, however, the analysis particularly focused on the measured power output by the wind turbine. The power output time series of data for each day was categorized by total energy generation and standard deviation, and the day that represented the highest combination of these two metrics was chosen – December 25th, 2022. This process was then repeated for a moving four-hour window within this day to identify the most statistically variable period. Finally, this four-hour period was scaled by 65% to match the 1.25 MW electrolyzer. The electrolysis system controls hydrogen production by varying DC current applied to the stack, from a maximum of 3000 A to a minimum safe operation of 300 A, or 10%. Because the current – voltage characteristic changes as the stack ages and efficiency degrades, the actual minimum safe operating power changes over time. The historical wind profiles were translated from power (kilowatts) to current (amperes) using a curve fit with calibration data and sent to the electrolyzer power supply at 1 Hz frequency. For more details on the statistical analysis process, see the presentation labeled “ Public Reference Data for Megawatt-Scale Hydrogen Electrolysis” provided with each data entry. These datasets report relevant hydrogen balance-of-plant and system data, all captured at 1 Hz, including hydrogen mass production measured with an Emerson Coriolis flow meter. Each .zip file represents a single wind turbine electrolysis experiment and is formatted as follows: {technology}_{scaling factor}-{electrolyzer ramp rate in amperes/second} For instance, “wind-GE1.5MW_0.65-400.zip” represents the hour-long experiment using historical data from the wind-GE1.5MW turbine, scaled to 65%, with the electrolyzer power supply set to a maximum ramp rate (gain and slew) of 400 A/s. Each .zip folder contains the following files: A .csv file containing raw data An .xlsx file explaining all the fields in the raw data. A .png plot showing the time series of hydrogen production, electrolysis power consumption, and wind power input. A PDF file detailing the historical wind data statistical analysis used to generate the wind profile. An experiment labeled “characterization_200.zip” demonstrates the MC250 electrolyzer steady-state response with 30-minute load steps for a total duration of 5 hours. Finally, a .csv file is provided with all simulated wind experiments combined into one dataset labeled "combined_historical_wind_experiments.csv". NLR also built an AI/machine-learning predictive model based on these datasets. The model ingests the electrolyzer current command in amperes, as well as various pressures and temperatures across the system, and predicts hydrogen output in kilograms per hour. The complete model can be found at https://huggingface.co/NatLabRockies/ptmelt-hydrogen-electrolysis [1] nelhydrogen.com/product/mc-series-electrolyser .

08 HYDROGEN↗
DOE OSTI2020

Recent developments in catalyst-related PEM fuel cell durability

Cost and durability remain the two major barriers to the widespread commercialization of polymer electrolyte membrane fuel cell (PEMFC)-based power systems, especially for the most impactful but challenging fuel cell electric vehicle (FCEV) application. Commercial FCEVs are now on the road; however, their PEMFC systems do not meet the cost targets established by the U.S. Department of Energy, primarily due to the high platinum loading needed on the cathode to achieve the requisite performance and lifetime. Furthermore, while the activities of a number of commercial Pt-based alloy cathode catalysts exceed the beginning-of-life (BOL) targets, these activities, and the overall cathode performance, degrade via a variety of mechanisms described herein. Degradation is mitigated in current FCEVs by utilizing a cathode catalyst with a lower BOL activity (e.g., much lower transition metal alloy content and larger BOL nanoparticle size), necessitating higher catalyst loadings, and through the utilization of system controls that avoid conditions known to exacerbate degradation processes, such as limiting the fuel cell stack voltage range. The design and development of active and robust materials and eliminating the need for vehicle mitigation strategies would greatly simplify the operating system, allowing for greater transient operation, avoiding large hybridization, and curtailing of fuel cell power. Although system mitigation strategies have provided the near-term pathway for FCEV commercialization, material-specific solutions are required to further reduce costs and improve operability and efficiency. Future material developments should focus on stabilization of the electrode structure and minimization of the catalyst particle susceptibility to dissolution caused by oxide formation and reduction over PEMFC cathode-relevant operating potentials plus minimization of support corrosion. Ex situ accelerated stress tests have provided insight into the processes responsible for material and performance degradation and will continue to provide useful information on the relative stability of materials and benchmarks for robust and stable materials-based solutions not requiring system mitigation strategies to achieve adequate lifetime.

25 ENERGY STORAGE↗
DOE OSTI2022

Gas Permeability Test Protocol for Ion-Exchange Membranes

The membrane-based electrolysis of water is a growing topic of interest due to the advantages of employing membranes in hydrogen production efficiency and system safety over the traditional alkaline water electrolysis. Ion-exchange membranes with low gas permeability are highly desirable for stable and safe operation of membrane-based water-splitting technologies, hence gas permeability through ion-exchange membranes needs to be properly assessed with standardized methods. We addressed three methods to measure gas permeability of ion-exchange membranes, a pressure permeation cell, chronoamperometry microelectrodes, and in situ testing of the membrane electrode assembly, and provide a guideline for choosing the appropriate method for the targeted operating conditions of the water electrolyzers.

08 HYDROGEN↗
DOE OSTI2024

Polyamide-Based Ion Exchange Membranes: Cation-Selective Transport through Water Purification Membranes

Ion-selective membranes are necessary components of many electrochemical systems including fuel cells, electrolyzers, redox flow batteries, and electrodialyzers. Perfluorinated sulfonated membranes (PFSMs) dominate these applications due to their excellent combination of fast ion transport, stability, and processability. However, perfluorinated cation exchange membranes (CEMs) are expensive, and their production process involves chemistry that generates toxic perfluorinated chemicals. The development of affordable, nonfluorinated membranes with a competitive combination of high ion selectivity, transport, and stability could help enable the widespread use of the technologies listed above while hastening the development of emerging electrochemical systems, including aqueous alkaline CO 2 sorbent regeneration. To this end, we pursue the use of thin-film composite polyamide (PA-TFCs) membranes–those that typically find application in reverse osmosis and nanofiltration desalination–as cation-selective exchange membranes. Given their negative surface charge under neutral-to-alkaline conditions, PA-TFCs can serve as effective CEMs in these pH regimes. We prepared a series of PA-TFCs from traditional monomers (trimesoyl chloride and piperazine) and compared their thicknesses, charge densities, water transport properties, ion transport properties, and long-term stability in a high pH environment to traditional CEMs (Nafion and FKE) and commercial nanofiltration and reverse osmosis membranes. We find that some of the best-performing PA-TFC membranes have similar resistances and Na + transference numbers compared to Nafion 117 in Na 2 SO 4 and NaHCO 3 -containing solutions. This proof-of-principle study suggests that further optimization of PA-TFCs could enable cost-effective ion exchange membrane alternatives to PFSMs.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Energy-efficient carbon capture from industrial point sources via commercially available green solvent and hollow fiber membrane contactors

Solvent-based absorption systems have emerged in the carbon capture space due to their high absorption capacities, reusability, and favorable energy requirements. Using diethyl sebacate as a solvent for pre- and post-combustion carbon capture has advantages over other solvents, including high hydrophobicity, low viscosity, low vapor pressure, high CO 2 solubility, high CO 2 selectivity, and being commercially available in large quantities. Despite these advantageous properties, the use of diethyl sebacate as a solvent for post-combustion carbon capture has not been studied in detail. To examine the capability of diethyl sebacate, a scalable, energy-efficient, hollow fiber membrane (microporous polypropylene and polyvinylidene fluoride) contactor (HFMC)-based process with low-cost and high surface area is investigated. A purity of 95.3 % CO 2 with 46 % recovery in one absorption stage was achieved, with a permeate flux over one magnitude greater than using a deep eutectic solvent in the same system. Technoeconomic analysis determined a ∼ 0.8 GJ per ton of CO 2 at a processing cost of ∼$93 per ton of CO 2 . Results from this work underscore the potential for utilizing green solvents in HFMC-based separation processes for effective carbon capture and provide a pathway towards practical deployment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Membrane-Based Air Dehumidification Using Organic Ionic Liquid Desiccant

Membrane Ionic Liquid Desiccant Air Dehumidification (MILDAD) is a promising alternative to conventional dehumidification systems that employ mechanical compressors and refrigerant-based cooling with evaporator and condensing coils. However, its application has been limited due to high manufacturing and installation cost, durability issues, concerns with corrosion due to leakage and salt carry over into the downstream air and onto surfaces. This paper reviews substantial progress made with new systems based on combining advanced ionic membranes that are pressure resistant, thin walled with high water permeability, and non-porous with synthetic organic, non-crystalline ionic liquid desiccants. Alternative design configurations are discussed comparing cross flow shell-and-tube membrane contactors employing ionic membrane tubes through which ionic liquid desiccant air flows. Performance data for MILDAD prototypes is provided. Dehumidification of the incoming supply airstream and regeneration into exhausted building air is demonstrated. The latent effectiveness of the MILDAD system will be discussed along with some future steps to improve performance of the system.

ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATION↗
DOE OSTI2022

Biocatalytic system for comparatively assessing the functional association of monolignol cytochrome P450 monooxygenases with their redox partners

Lignin is a complex heterogenous polymer derived from oxidative radical polymerization of three monolignols, i.e., p-coumaryl alcohol, coniferyl alcohol and sinapyl alcohol. These lignin monomeric precursors structurally differ in their methoxy groups of the benzene rings. In phenylpropanoid-monolignol biosynthetic pathway, the endoplasmic reticulum (ER)-resident cytochrome P450 monooxygenases, cinnamate 4-hydroxylase, coumaroyl ester 3´-hydroxylase and ferulate 5-hydroxylase, establish the key structural characteristics of monolignols. The catalysis of cytochrome P450 monooxygenase requires reducing power, which is supplied by the ER electron transfer chains, composed of cytochrome P450 oxidoreductase (CPR), cytochrome b5 reductase (CBR) and/or cytochrome b5 protein (CB5), from cofactor NADPH or NADH. While NADPH-dependent CPR serves as the typical electron donor for most P450 enzymes, in some cases, the CBR-CB5 or CPR-CB5 electron transfer system also transfers electrons to the terminal P450 enzymes. There are tremendous studies focusing on the discovery and characterization of cytochrome P450 monooxygenases. However, very limited attention has been paid to the versatility and the roles of electron transfer components in the P450 catalytic system. Due to the membrane-residence property of both P450 enzymes and electron transfer components, it is challenging to establish an effective experimental system to evaluate the functional association of P450s with their redox partners. This chapter describes a yeast cell biocatalytic system and the related experimental procedures for comparatively assessing the functional relationship of monolignol biosynthetic P450 enzymes and different redox partners in their catalysis.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

An experimental and modeling study of the application of membrane contactor reactors to methanol synthesis using pure CO 2 feeds

We describe here a post-combustion CO 2 capture and utilization (CCU) technology that converts the CO 2 into methanol (MeOH), a valuable chemical, thus providing a way to monetize the carbon captured to offset process costs. Methanol synthesis (MeS) has been discussed recently for application to CCU, but thermodynamic limitations make it difficult to convert in a single pass a large CO 2 fraction. Conventional catalysts show slow kinetics in converting CO 2 -rich syngas (or pure CO 2 ) into MeOH. Our Group developed a novel MeS process, employing a membrane contactor reactor (MCR) system that attains carbon conversions significantly higher than equilibrium. Our focus here is to process pure CO 2 streams by combining the MCR with a separate reactor, which converts the CO 2 into a syngas via the reverse water gas shift (RWGS) reaction. In this preliminary effort, the RWGS reactor (RWGSR) is assumed to reach equilibrium. Additional MeS kinetic rate data are generated validating experimentally the ability of the MeS-MCR to process as a feed the RWGSR exit stream. The performance of the combined (RWGSR/MeS-MCR) system is then simulated using a recently developed MeS-MCR model. In conclusion, the findings are encouraging, and research is currently ongoing to experimentally validate the RWGSR/MeS-MCR system performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Asynchronous Reciprocal Coupling of Martini 2.2 Coarse-Grained and CHARMM36 All-Atom Simulations in an Automated Multiscale Framework

The appeal of multiscale modeling approaches is predicated on the promise of combinatorial synergy. However, this promise can only be realized when distinct scales are combined with reciprocal consistency. Here, we consider multiscale molecular dynamics (MD) simulations that combine the accuracy and macromolecular flexibility accessible to fixed-charge all-atom (AA) representations with the sampling speed accessible to reductive, coarse-grained (CG) representations. AA-to-CG conversions are relatively straightforward because deterministic routines with unique outcomes are achievable. Conversely, CG-to-AA conversions have many solutions due to a surge in the number of degrees of freedom. While automated tools for biomolecular CG-to-AA transformation exist, we find that one popular option, called Backward, is prone to stochastic failure and the AA models that it does generate frequently have compromised protein structure and incorrect stereochemistry. Although these shortcomings can likely be circumvented by human intervention in isolated instances, automated multiscale coupling requires reliable and robust scale conversion. In this work, we detail an extension to Multiscale Machine-learned Modeling Infrastructure (MuMMI), including an improved CG-to-AA conversion tool called sinceCG. This tool is reliable (~98% weakly correlated repeat success rate), automatable (no unrecoverable hangs), and yields AA models that generally preserve protein secondary structure and maintain correct stereochemistry. We describe how the MuMMI framework identifies CG system configurations of interest, converts them to AA representations, and simulates them at the AA scale while on-the-fly analyses provide feedback to update CG parameters. Application to systems containing the peripheral membrane protein RAS and proximal components of RAF kinase on complex eight-component lipid bilayers with ~1.5 million atoms is discussed in the context of MuMMI.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Confinement Reconstruction Unlocks Stable Ru Single Atom-Doped IrO x Anodes for Long-Term High-Rate CO 2 Electrolysis

IrO 2 is a commonly employed anode catalyst for CO 2 electrolysis in membrane electrode assembly (MEA) systems. However, under high current densities, its structural reconstruction leads to activity loss and stability degradation, limiting the industrial viability of CO 2 electrolysis. In this work, we demonstrated a confinement reconstruction strategy to precisely regulate the structural evolution during electrolysis. Ethylene glycol serves as a structural modulator, protecting the catalyst surface, suppressing soluble species formation, and promoting ordered structural evolution. Single-atom Ru acts as a stability enhancer, forming robust Ir–O–Ru bridging structures that facilitate an ordered transformation from a 4-fold [RuO 4 ]/[IrO 4 ] to a 6-fold symmetry [RuO 6 ]/[IrO 6 ] octahedral framework, thereby enhancing structural rigidity and long-term stability. As a result, in MEA-based CO 2 electrolysis, the catalyst achieves a stable operation at 200 mA cm –2 for 480 h, maintaining a CO selectivity above 80%. Theoretical calculations further elucidate that the enhanced stability originates from the suppression of oxygen vacancy formation, making the lattice-oxygen-mediated mechanism (LOM) potentially less favorable. This work provides insights into the structural evolution of the OER catalysts under high-current-density conditions, paving the way for large-scale CO 2 electrolysis commercialization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Structure of phospholipase Cε reveals an integrated RA1 domain and previously unidentified regulatory elements

Phospholipase Cε (PLCε) generates lipid-derived second messengers at the plasma and perinuclear membranes in the cardiovascular system. It is activated in response to a wide variety of signals, such as those conveyed by Rap1A and Ras, through a mechanism that involves its C-terminal Ras association (RA) domains (RA1 and RA2). However, the complexity and size of PLCε has hindered its structural and functional analysis. Herein, we report the 2.7 Å crystal structure of the minimal fragment of PLCε that retains basal activity. This structure includes the RA1 domain, which forms extensive interactions with other core domains. A conserved amphipathic helix in the autoregulatory X–Y linker of PLCε is also revealed, which we show modulates activity in vitro and in cells. The studies provide the structural framework for the core of this critical cardiovascular enzyme that will allow for a better understanding of its regulation and roles in disease.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Slippery liquid infused porous surface (SLIPS) condensers for high efficiency air gap membrane distillation

Abstract To address growing water scarcity, we must improve the energy efficiency of thermal desalination technologies such as air gap membrane distillation. However, promising functional materials such as slippery liquid infused porous surfaces have not yet implemented for any desalination technology. Here, we fabricate and test slippery liquid infused porous surfaces (using Krytox 16,256 lubricant and CuO nanostructures) in an air gap membrane distillation apparatus. System-level transport models, validated by experimental data, establish a framework for improving performance through enhanced condensation surfaces. Results are obtained across a range of temperatures (50–80 °C), salinities (5–105 g/kg), and module lengths. We find that small air gap thickness and efficient droplet shedding significantly improves performance. The CuO Krytox process achieves these with a conductive-self-limiting coating, high nanostructure rugosity, strong covalent and metallic bonding, high hydrophobicity, minimal droplet pinning sites, and ultra-low contact angle hysteresis. The greatest efficiency enhancement from SLIPS is derived from the improved droplet shedding, which allows for reduced gap sizes without flooding, and is further augmented by the increased permeate flux.

Yogi, Yashwant S.↗