Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNETRONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Physical properties of RF magnetron sputtered GaN/n-Si thin film: impacts of RF power

GaN thin film was successfully produced on n-Si(100) substrate by RF magnetron sputter under different RF power. Experimental measurement techniques such as UV/Vis spectroscopy, field emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), atomic force microscopy (AFM), and Micro-Raman Spectroscopy were used to research effects of Radio Frequency power on physical properties of produced thin film. It has been found that produced thin film was polycrystalline structure with (100) and (110) planes of hexagonal GaN from X-ray diffraction measurement result. It also proved that increasing RF power gives rise to deterioration in crystal quality of GaN thin film. Reason of this deterioration was discussed. It has been achieved that increasing RF power has resulted in decreasing optical band gap energy of GaN thin film. Reasons for these changes in optical band gap energy were explained. It was seen that some thin films were grown as layer-plus-island mode (Stranski–Krastanov growth mode) and others were grown as layer-by-layer growth mode (Frank van der Merwe mode) from AFM analysis. It has been found that increasing RF power has resulted in improvement of surface morphology of thin film from field emission scanning electron microscopy analysis. However, reaching RF power to 125 W leads to start to deteriorate of surface of GaN thin film. The reasons for this have been discussed. E{sub 1}(TO) transverse optical phonon mode of hexagonal GaN with different intensity was detected from Micro-Raman Spectroscopy measurement. The reasons for this difference have been discussed. It was concluded that RF power has played a significant role in growing high quality GaN thin film. Morphological, structural, and optical properties of GaN thin film were enhanced by controlling RF power, making them a potential candidate for LED, solar cell, diode application.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Role of oxygen concentrations on structural and optical properties of RF magnetron sputtered ZnO thin films

We report an investigation on the effect of oxygen flow rate on the structural and optical properties of zinc oxide thin films prepared by RF magnetron sputtering. The structural measurements were carried using grazing incidence X-ray diffraction, atomic force microscopy and Raman spectroscopy. The role of oxygen partial pressure on the crystallinity, the surface morphology and vibrational modes has been established. The optical properties of the films were investigated using FR-Basic-VIS/NIR fitted with FR-Monitor software for film thickness, refractive index and color determination. The film thickness is observed to increase when oxygen is introduced at 4 sccm but eventual decrease with increase in the flow rate an indication of initial increase in rate of deposition followed by reduction. Elaborate explanations of these trends are provided.

36 MATERIALS SCIENCE↗

Properties of Gallium Oxide Films Obtained by HF-Magnetron Sputtering

The results of an analysis of structure and phase composition of gallium oxide films obtained by HF-magnetron sputtering are presented. It is shown that in the interval 290–350 K, the increase in the film conductivity with increasing temperature is due to the excitation of electrons from a local level Е{sub t} located 0.95 eV below the conduction band bottom.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Preparation and Oxidation Performance of a NiCoCrAlYSiHf + NiAl Composite Coating Deposited by Arc Ion Plating and Magnetron Sputtering Techniques

A NiCoCrAlYSiHf+NiAl composite coating was deposited onto a second-generation single-crystal superalloy René N5 by methods of arc ion plating and magnetron sputtering. After vacuum annealing, the composite coating exhibited a gradient distribution of elements, in which Al was enriched in outer layer and Cr was enriched in inner layer. Compared with conventional NiCoCrAlYSiHf and β-NiAl coatings, the composite coating was evaluated in isothermal and cyclic oxidation tests at 1100 °C in ambient air. The results showed that the oxidation rate of the composite coating was lower than that of NiCoCrAlYSiHf coating. Meanwhile, the extent of interdiffusion between coating and substrate in the composite coating was slighter compared with that in the β-NiAl coating. Microstructure evolutions of the composite coating after annealing and further oxidation test are investigated.

36 MATERIALS SCIENCE↗

Properties of Nb3Sn films fabricated by magnetron sputtering from a single target

Superconducting Nb3Sn films were fabricated on sapphire and fine grain Nb substrates by magnetron sputtering from a single stoichiometric Nb3Sn target. The structural, morphological and superconducting properties of the films annealed for 24 h at temperatures of 800-1000 {\deg}C were investigated. The effect of the annealing time at 1000 {\deg}C was examined for 1, 12, and 24 h. The film properties were characterized by X-ray diffraction, scanning electron microscopy, atomic force microscopy, energy dispersive X-ray spectroscopy, and Raman spectroscopy. The DC superconducting properties of the films were characterized by a four-point probe measurement down to cryogenic temperatures. The RF surface resistance of films was measured over a temperature range of 6-23 K using a 7.4 GHz sapphire-loaded Nb cavity. As-deposited Nb3Sn films on sapphire had a superconducting critical temperature of 17.21 K, which improved to 17.83 K when the film was annealed at 800 {\deg}C for 24 h. For the films annealed at 1000 {\deg}C, the surface Sn content was reduced to ~11.3 % for an annealing time of 12 h and to ~4.1 % for an annealing time of 24 h. The Raman spectra of the films confirmed the microstructural evolution after annealing. The RF superconducting critical temperature of the as-deposited Nb3Sn films on Nb was 16.02 K, which increased to 17.44 K when the film was annealed at 800 {\deg}C for 24 h.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Improvement of adhesion and barrier properties of biomedical stainless steel by deposition of YSZ coatings using RF magnetron sputtering

The AISI 316L stainless steel (SS) has been widely used in both artificial knee and hip joints in biomedical applications. In the present study, yttria stabilized zirconia (YSZ, ZrO{sub 2} + 8% Y{sub 2}O{sub 3}) films were deposited on AISI 316L SS by radio-frequency magnetron sputtering using different power densities (50–250 W) and deposition times (30–120 min) from a YSZ target. The crystallographic orientation and surface morphology were studied using X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The effects of the surface modification on the corrosion performance of AISI 316L SS were evaluated in phosphate buffered saline (PBS) solution using an electrochemical test on both the virgin and coated samples. The YSZ coatings have a (111) preferred orientation during crystal growth along the c-axis for short deposition times (30–60 min), whereas a polycrystalline structure forms during deposition times from 90 to 120 min. The corrosion protective character of the YSZ coatings depends on the crystal size and film thickness. A significant increase in adhesion and corrosion resistance by at least a factor of 46 and a higher breakdown potential were obtained for the deposited coatings at 200 W (120 min). - Highlights: • Well-formed and protective YSZ coatings were achieved on AISI 316L SS substrates. • Films grown at high power and long deposition time have polycrystalline structures. • The crystal size varies from ∼ 5 to 30 nm as both power and deposition time increased. • The differences of corrosion resistance are attributed to internal film structure.

36 MATERIALS SCIENCE↗

Influence of vanadium incorporation on the microstructure, mechanical and tribological properties of Nb–V–Si–N films deposited by reactive magnetron sputtering

Composite Nb–V–Si–N films with various V contents (3.7–13.2 at.%) were deposited by reactive magnetron sputtering and the effects of V content on the microstructure, mechanical and tribological properties of Nb–V–Si–N films were investigated. The results revealed that a three-phase structure, consisting of face-centered cubic (fcc) Nb–V–Si–N, hexagonal close-packed (hcp) Nb–V–Si–N and amorphous Si{sub 3}N{sub 4}, co-exists in the Nb–V–Si–N films and the cubic phase is dominant. The hardness and critical load (L{sub c}) of Nb–V–Si–N films initially increased gradually and reached a summit, then decreased with the increasing V content in the films and the maximum values were 35 GPa and 9.8 N, respectively, at 6.4 at.% V. The combination of V into Nb–Si–N film led to the fracture toughness linearly increasing from 1.11 MPa·m{sup 1/2} at 3.7 at.% V to 1.67 MPa·m{sup 1/2} at 13.2 at.% V. At room temperature (RT), the average friction coefficient decreased from 0.80 at 3.7 at.% V to 0.55 at 13.2 at.% V for the Nb–V–Si–N films. The wear rate of Nb–V–Si–N films initially decreased and then increased after reaching a minimum value of about 6.35 × 10{sup −} {sup 7} mm{sup 3}/N·mm at 6.4 at.% V. As the rise of testing temperature from 200 °C to 600 °C, the average friction coefficient of Nb–V–Si–N films decreased with the increase of the testing temperature regardless of V content. However, the wear rate gradually increased for all films. The average friction coefficient and wear rate at RT and elevated temperatures were mainly influenced by the vanadium oxides with weakly bonded lattice planes. - Highlight: • Fcc-Nb–V–Si–N, hcp-Nb–V–Si–N and amorphous Si{sub 3}N{sub 4} co-existed in the films. • The amount of Si{sub 3}N{sub 4} decreased with increasing V content in the films. • Hardness of Nb–V–Si–N film (6.4 at.%) reached a maximum value of 35 GPa. • Addition of V led to the increase of fracture toughness. • Tribological properties were influenced by lubricant wear debris.

36 MATERIALS SCIENCE↗

Effect of annealing on Curie temperature and phase transition in La{sub 0.55}Sr{sub 0.08}Mn{sub 0.37}O{sub 3} epitaxial films grown on SrTiO{sub 3} (100) substrates by reactive radio frequency magnetron sputtering

Mn-poor LaSrMnO{sub 3} (LSMO) epitaxial films were grown on SrTiO{sub 3} (100) substrates by radio frequency magnetron sputtering in an argon and oxygen gas mix, and then the samples were annealed in air at various temperatures (T{sub a}). 2 theta-chi X-ray diffraction mapping, nano-beam diffraction analysis through transmission electron microscopy, and electron back scatter diffraction through scanning electron microscopy revealed that the crystal symmetry of the LSMO films changed from monoclinic/orthorhombic to rhombohedral on annealing in air. Curie temperature (T{sub C}) of the LSMO films was found to increase with increasing T{sub a}, and become higher than the room temperature at T{sub a} ≥ 861 °C, indicating that the cause of these changes was the filling of oxygen and the transition of the crystal symmetry into rhombohedral. - Highlights: •Mn-poor LSMO changed from monoclinic/orthorhombic to rhombohedral by oxygen supply. •Mn-poor LSMO was increased T{sub C} by changed crystal symmetry, and it showed T{sub C} above RT. •Annealed in air effectively supplied O{sub 2} more than O{sub 2} gas during sputtering •EBSD is useful to evaluate crystal symmetry of complex oxide film from the substrate.

36 MATERIALS SCIENCE↗

Length-scale-dependent nanoindentation creep behaviour of Ti/Al multilayers by magnetron sputtering

This study presented length-scale-dependent room temperature creep behaviour of Ti/Al multilayers by nanoindentation. Ti/Al multilayers with individual layer thickness ranging from 10 nm to 250 nm were prepared by a direct current magnetron sputtering method. Microstructural analysis showed that the prepared Ti/Al multilayers were polycrystalline, with strong Ti (0002) and Al (111) texture. Nanoindentation creep tests were performed to examine the time-dependent creep deformation, stress exponent, creep strain rate sensitivity and contact creep compliance of the multilayers at room temperature. It was found that both the maximum creep deformation and the creep strain rate sensitivity increase with an increase in the individual layer thickness, indicating a length-scale-dependent creep behaviour of the Ti/Al multilayers. The values of stress exponent were found to lay in the range of 15.74–61.46, implying that the creep behaviour of the multilayers was controlled by the dislocation creep mechanism. Finally, the contact creep compliances of the Ti/Al multilayers were well modelled by a two-element Kelvin-Voigt model. From this, it was determined that the creep numbers and retardation times increased with increased individual layer thickness.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Correlation between structural and mechanical properties of RF magnetron sputter deposited hydroxyapatite coating

Highlights: • Microstructure and mechanical properties of textured hydroxyapatite (HA) coatings were evaluated. • TEM results revealed two types of coating microstructure corresponding to the film texture. • Elastic performance of the coating was determined by the texture of the HA coating. • HA coating with (300) texture showed larger elastic recovery. - Abstract: In the present study hydroxyapatite (HA) thin films with a,b-plain and c-plain preferential orientation were prepared by means of RF-magnetron sputtering with water vapor addition into a working gas atmosphere to investigate the influence of microstructural features on mechanical performance of the coating at nanoscale. The mechanical properties of the HA coatings textured along a,b- and c-axes by nanoindentation conclusively highlight that elastic modulus, H/E ratio, H{sup 3}/E{sup 2} parameter and percent of elastic recovery are determined by preferential orientation of the film. Nanoindentation reveals that the HA films exhibiting (300) texture possess commensurate nanohardness and lower elastic modulus compared to (002) oriented films, indicating that the former films possess higher resistance to cracking. The (002) and (300) textured coatings exhibited a nanohardness of 4.7 ± 2.0 GPa and 4.4 ± 2.2 GPa, respectively. The elastic modulus of the HA film with (300) and (002) preferential orientation was 75 ± 40 GPa and 103 ± 40 GPa, respectively. The HA coating with (300) texture showed a higher percentage of elastic recovery of 92% within unloading than that of the (002) textured film (69%).

36 MATERIALS SCIENCE↗

Indium tin oxide films deposited by thermionic-enhanced DC magnetron sputtering on unheated polyethylene terephthalate polymer substrate

Indium tin oxide thin films were deposited onto polyethylene terephthalate substrates via thermionic enhanced DC magnetron sputtering at low substrate temperatures. The structural, optical and electrical properties of these films are methodically investigated. The results show that compared with traditional sputtering, the films deposited with thermionic emission exhibit higher crystallinity, and their optical and electrical properties are also improved. Indium tin oxide films deposited by utilizing thermionic emission exhibit an average visible transmittance of 80% and an electrical resistivity of 4.5 x 10{sup -4} {Omega} cm, while films made without thermionic emission present an average visible transmittance of 74% and an electrical resistivity of 1.7 x 10{sup -3} {Omega} cm.

36 MATERIALS SCIENCE↗

Investigation of antiperovskite Mn{sub 3}CuN{sub x} film prepared by DC reactive magnetron sputtering

Antiperovskite Mn{sub 3}CuN{sub x} film was prepared by dc reactive magnetron sputtering. It is the first time to report an antiperovskite ternary nitride film. The composition and crystal structure were characterized by energy dispersive spectroscope (EDS), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD). From the XRD pattern, it displays a (1 0 0) preferential orientation. A comparative study on the properties of Mn{sub 3}CuN{sub x} film and the bulk sample was presented. The film exhibits an antiferromagnetic to paramagnetic transition around 135 K, similar with the bulk sample. With temperature, the resistivity of the film shows semiconductor-like behavior throughout the measured temperature region, whereas there is an abrupt drop around the magnetic transition for the bulk. The variable temperature XRD results indicate that the film did not display any structure transition and shows a normal linear thermal expansion property around the magnetic transition.

36 MATERIALS SCIENCE↗

RBS, XRR and optical reflectivity measurements of Ti-TiO{sub 2} thin films deposited by magnetron sputtering

Highlights: Black-Right-Pointing-Pointer The single-, bi- and tri-layered films of Ti-TiO{sub 2} deposited onto Si(1 1 1) substrates. Black-Right-Pointing-Pointer Three methods RBS, XRR, optical reflectometer were used. Black-Right-Pointing-Pointer The real thickness of each layer was smaller than 50 nm. Black-Right-Pointing-Pointer Ti and TiO{sub 2} film-densities were slightly lower than the corresponding bulk values. -- Abstract: Single-, bi- and tri-layered films of Ti-TiO{sub 2} system were deposited by d.c. pulsed magnetron sputtering from metallic Ti target in an inert Ar or reactive Ar + O{sub 2} atmosphere. The nominal thickness of each layer was 50 nm. The chemical composition and its depth profile were determined by Rutherford backscattering spectroscopy (RBS). Crystallographic structure was analysed by means of X-ray diffraction (XRD) at glancing incidence. X-ray reflectometry (XRR) was used as a complementary method for the film thickness and density evaluation. Modelling of the optical reflectivity spectra of Ti-TiO{sub 2} thin films deposited onto Si(1 1 1) substrates provided an independent estimate of the layer thickness. The combined analysis of RBS, XRR and reflectivity spectra indicated the real thickness of each layer less than 50 nm with TiO{sub 2} film density slightly lower than the corresponding bulk value. Scanning Electron Microscopy (SEM) cross-sectional images revealed the columnar growth of TiO{sub 2} layers. Thickness estimated directly from SEM studies was found to be in a good agreement with the results of RBS, XRR and reflectivity spectra.

36 MATERIALS SCIENCE↗

Fabrication of LiCoO{sub 2} thin film cathodes by DC magnetron sputtering method

LiCoO{sub 2} thin films were fabricated on Al substrate by direct current magnetron sputtering method. The effects of Ar/O{sub 2} gas rates and annealing temperatures were investigated. Crystal structures and surface morphologies of the deposited films were investigated by X-ray diffraction, Raman scattering spectroscopy and field emission scanning electron microscopy. The as-deposited LiCoO{sub 2} thin films exhibited amorphous structure. The crystallization starts at the annealing temperature over 400 °C. However, the annealed films have the partially disordered structure without completely ordered crystalline structure even at 600 °C annealing. The electrochemical properties of the LiCoO{sub 2} films were investigated by the charge–discharge and cycle measurements. The 500 °C annealing film has the highest capacity retention rate of 78.2% at 100th cycles.

36 MATERIALS SCIENCE↗

Tribological properties of metal doped a-C film by RF magnetron sputtering method

We deposited various metal doped amorphous carbon (a-C:Me) films by radio frequency (RF) magnetron co-sputtering method. Tungsten (W), molybdenum (Mo), and chromium (Cr) were used as the doping metals in a-C film. The applied power on carbon and metal (W, Mo, and Cr) target were 150 W and 40 W, respectively. a-C:Me films exhibited smooth and uniform surface roughness and the hardness over 15 GPa. Specially, a-C:W film showed the maximum hardness of 18.5 GPa. The coefficient of friction of a-C:W film is relatively lower than that of other films and the critical load value of a-C:W film is higher. These results are related to the concentration of metal in the carbon matrix by the difference of sputtering yield and the change of the structure by the metal bonding. Consequently, W metal is good candidate as the doping metal for the improvement of tribological characteristics.

36 MATERIALS SCIENCE↗

Ferroelectric and dielectric study of strontium tantalum based perovskite oxynitride films deposited by reactive rf magnetron sputtering

Highlights: • Oxynitride perovskite thin films were deposited by reactive sputtering. • Films are textured or epitaxially grown on MgO and Nb-SrTiO{sub 3} substrates. • Local piezoelectric and ferroelectric behavior was highlighted by PFM. • A 1600 nm-thick film presents a permittivity of 175 at 10 kHz and RT. • Permittivity is around 65 in high frequency range. - Abstract: Strontium and tantalum based oxynitride perovskite thin films were deposited by reactive magnetron sputtering. Epitaxial films deposited on Nb-SrTiO{sub 3} substrates show smooth surfaces with roughness values from 1.5 to 3.6 nm for a thickness of films in the range 20–1600 nm. The samples are yellow with band gap values around 2.35 eV. Piezo-force microscopy characterization pointed out the local piezoelectric and ferroelectric behavior of the oxynitride perovskite films. In the low frequency range, the 1600 nm-thick film exhibits a permittivity of 175 at 10 kHz, with dielectric losses of 0.055. Permittivity is lowered in high frequencies with a value around 65 obtained on a 1520 nm-thick film deposited on MgO substrate, which is textured with a preferential c-axis orientation. No accordability of the permittivity was highlighted at a macroscopic scale. The moderate crystallographic strain evidenced in the 20 nm thin film does not induce a high permittivity.

36 MATERIALS SCIENCE↗

Effects of growth rate and dynamic substrate tilt on properties of Au-Ta alloy films deposited by high-power impulse magnetron sputtering

Gold-tantalum (Au—Ta) alloys are promising for next-generation hohlraums for magnetically-assisted indirect-drive inertial confinement fusion. Hohlraum fabrication involves sputter deposition of ultrathick coatings on sphero-cylindrical substrates. The control of physical properties of such coatings remains a challenge. Here, in this work, we systematically study effects of the growth rate and dynamic substrate tilt on properties of AuTa 4 films deposited onto rotating planar substrates mounted at different tilt angles to mimic different regions of the sphero-cylindrical surface of a hohlraum. We use high-power impulse magnetron sputtering (HiPIMS) in the constant charge per pulse mode with a pulse duration of 100 μs, a charge per pulse of 190 μC, a peak target current of about 3 A, and the pulse frequency varied in the range of 400–1400 Hz. The Langmuir probe, mass-resolved ion energy spectrometry, and optical emission spectroscopy are used to monitor plasma discharge characteristics in order to isolate and study effects of the growth rate. The deposition rate and the ballistics and energetics of depositing species are estimated by Monte Carlo simulations. Results show that the film microstructure, crystallographic phase, residual stress, and electrical resistivity strongly depend on both the deposition rate and substrate tilt, highlighting their critical role in tailoring properties of Au—Ta films during hohlraum fabrication.

36 MATERIALS SCIENCE↗

Photoreduction of CO{sub 2} by TiO{sub 2} nanocomposites synthesized through reactive direct current magnetron sputter deposition.

The photoreduction of CO{sub 2} into methane provides a carbon-neutral energy alternative to fossil fuels, but its feasibility requires improvements in the photo-efficiency of materials tailored to this reaction. We hypothesize that mixed phase TiO{sub 2} nano-materials with high interfacial densities are extremely active photocatalysts well suited to solar fuel production by reducing CO{sub 2} to methane and shifting to visible light response. Mixed phase TiO{sub 2} films were synthesized by direct current (DC) magnetron sputtering and characterized by X-ray diffraction (XRD), atomic force microscope (AFM), scanning electron microscope (SEM) and transmission electron microscope (TEM). Bundles of anatase-rutile nano-columns having high densities of two kinds of interfaces (those among the bundles and those between the columns) are fabricated. Films sputtered at a low deposition angle showed the highest methane yield, compared to TiO{sub 2} fabricated under other sputtering conditions and commercial standard Degussa P25 under UV irradiation. The yield of methane could be significantly increased ({approx} 12% CO{sub 2} conversion) by increasing the CO{sub 2} to water ratio and temperature (< 100 C) as a combined effect. These films also displayed a light response strongly shifted into the visible range. This is explained by the creation of non-stoichiometric titania films having unique features that we can potentially tailor to the solar energy applications.

03 NATURAL GAS↗