Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LiP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS2017

Off-Design Performance of a Streamline-Traced, External-Compression Supersonic Inlet

A computational study was performed to explore the aerodynamic performance of a streamline-traced, external-compression inlet designed for Mach 1.664 at off-design conditions of freestream Mach number, angle-of-attack, and angle-of-sideslip. Serious degradation of the inlet performance occurred for negative angles-of-attack and angles-of-sideslip greater than 3 degrees. At low subsonic speeds, the swept leading edges of the inlet created a pair of vortices that propagated to the engine face. Increasing the bluntness of the cowl lip showed no real improvement in the inlet performance at the low speeds, but did improve the inlet performance at the design conditions. Reducing the inlet flow rate improved the inlet performance, but at the likely expense of reduced thrust of the propulsion system. Deforming the cowl lip for low-speed operation of the inlet increased the inlet capture area and improved the inlet performance.

distortion↗
NASA NTRS2018

Experimental and Computational Study of Tones Occurring with a Coaxial Nozzle

The source of audible tones occurring with a coaxial nozzle in a range of low Mach numbers is explored experimentally as well as computationally. The hardware is comprised of an inner and an outer nozzle, without a center-body, that are held together by a set of four struts. With increasing jet Mach number (M(sub j)), first a tone occurred at about 2550 Hz around M(sub j)=0.06. At higher values of M(sub j) a tone at 5200 Hz dominated the noise spectra. The corresponding nondimensional frequency, based on effective thickness of the inner nozzle lip and jet exit velocity, turned out to be about 0.2, a value characteristic of Karmann vortex shedding. Thus, vortex shedding from the inner nozzle lip could be linked to the tones. From a comparison of the acoustic wavelengths and the nozzle dimensions, it was inferred that the vortex shedding excited a one-quarter-wave resonance within the divergent section of either the inner nozzle or the outer nozzle. This led to the generation of the sharp tones.

nozzle↗
NASA NTRS2017

Jet Noise Prediction Using Hybrid RANS/LES with Structured Overset Grids

Hybrid RANS/LES simulations using the structured overset grid approach and a low dissipation finite-difference method within the Launch Ascent and Vehicle Aerodynamics (LAVA) solver framework are presented for jet noise prediction. The simulations are part of a validation effort to demonstrate jet noise prediction capability, to assess noise characteristics of next generation quiet supersonic commercial jets. Results are compared with experimental data acquired in the Small Hot Jet Acoustic Rig in the Aeroacoustic Propulsion Laboratory at NASA Glenn Research Center. Details of the structured overset grids, numerical discretization, and turbulence model are provided. Near-field comparisons to PIV data and far-field comparisons to microphone data are discussed. Excellent agreement of time-averaged mean quantities along the jet center-line and lip-line are obtained. Good agreement with root-mean-squared (RMS) quantities along the jet center-line are also obtained. An over prediction of lip-line RMS at the nozzle exit is observed leading to a small over-prediction of side-line far-field noise (less than 2 dB). Good agreement with far-field noise in the Mach wave radiation directions is achieved.

Housman, Jeffrey A.↗
NASA NTRS2019

Scaling Evaluation of Ice-Crystal Icing on a Modern Turbofan Engine in PSL Using the COMDES-MELT Code

This paper presents preliminary ice-crystal icing (ICI) altitude scaling evaluation results of a Honeywell Uncertified Research Engine (HURE) that was tested in the NASA Glenn Research Center Propulsion Systems Laboratory (PSL) during January of 2018. This engine geometry features a hidden core design to keep the core less exposed. The engine was fitted with internal video cameras to observe various ice buildup processes at multiple selected locations within the engine core flow path covering the fan stator, the splitter-lip/shroud/strut, and the high pressure compressor (HPC) variable inlet guide vane (IGV) regions. The potential ice accretion risk was pre-determined to occur by using NASA’s in-house 1D Engine Icing Risk assessment code, COMDES-MELT. The code was successful in predicting the risk of ice accretion in adiabatic regions like the fan-stator of the HURE at specific engine operating points. However at several operating points during the test, liquid water was observed running along the shroud toward the variable IGV of the HPC regions with an air temperature well below freezing, thus no particle melting could have occurred due to heating from the air alone. It was reasoned that other sources of heat were present in that region. To account for these heat sources the inlet total temperature was adjusted to give a wet bulb temperature of 24 F below the standard minimum wet bulb temperature of 492 R to allow ice to accrete in the splitter-lip/shroud/strut region, which was determined from a reference case where hard ice was observed in that region. With that adjustment the COMDES-MELT code was successful in providing operating points where there was a risk of ice accretion during the test campaign. In addition to calculating possible conditions at different selected lower altitudes, simulations were run to determine potential inlet conditions that could lead to ice-crystal accretion along the prescribed stations where the cameras were available. From there, scaled test conditions were determined by best matching the following three icing related parameters of the reference condition: (1) the local air total wet bulb temperature, (2) the local ice crystal cloud melt ratio and (3) the engine fan face ice/water to air mass flux ratio of the ice crystal cloud. Instantaneous images taken from the time-lapsed movies of ice buildup were used along with the relevant thermodynamic data of air, water vapor and local icing condition to help evaluate how closely the proposed altitude scaling method could be used in ground based test facility to duplicate selected reference ICI features observed at specific location inside this engine at different scale altitudes. Discussions on observed limitation for engine icing scaling application from this test campaign and needed improvement are provided. A scaling test procedure to help identify potential ICI risk conditions and possible ice accretion locations of a new turbofan engine is evaluated in PSL.

Engine Testing in PSL↗
NASA NTRS2021

Ice-Crystal Icing Investigation on a Honeywell Uncertified Research Engine in an Altitude Simulation Icing Facility

A Honeywell Uncertified Research Engine was exposed to various ice-crystal conditions in the NASA Propulsion Systems Laboratory (PSL). Simulations using NASA's one-dimensional (1D) Icing Risk Analysis tool were used to determine potential inlet conditions that could lead to ice-crystal accretion along the inlet of the core flowpath and into the high-pressure compressor. Baseline conditions were established, and parameters were varied to observe accretion characteristics. Data were acquired at altitudes varying from 5 kft to 45 kft, at nominal ice particle median volumetric diameters from 20 µm to 100 µm, and total water contents of 1 g/m3 to 12 g/m3. Metal temperatures were acquired for the inlet guide vane and vane stators 1–2. In situ measurements of the particle size distribution were acquired upstream and downstream of the engine fan face in order to study particle breakup behavior. Cameras were installed in the engine to capture ice accretions at the leading edge of the fan stator, splitter lip, and inlet guide vane. The goal of this study was to understand the key parameters of accretion, acquire particle breakup data aft of the fan, and generate a unique icing dataset for model development. Significant particle breakup downstream of the fan in the bypass was observed. The metal temperatures on the inlet guide vanes (IGVs) and stators show a temperature increase with increasing particle size. Accretion behavior at the fan stator and splitter lip across was very similar. However, accretion decreased with increasing particle size at the IGVs.

Ashlie B. Flegel↗
NASA NTRS2021

Time Resolved Particle Image Velocimetry in Nozzle Flow

Temporally resolved particle image velocimetry (TR-PIV) is the newest and most exciting tool recently developed to support our continuing efforts to characterize and improve our understanding of the decay of turbulence in jet flows—a critical element for understanding the acoustic properties of the flow. A new TR-PIV system has been developed at the NASA Glenn Research Center which is capable of acquiring planar PIV image frame pairs at up to 25 kHz. The data reported here were collected at Mach numbers of 0.5 and 0.9 and at temperature ratios of 0.89 and 1.76. The field of view of the TR-PIV system covered six nozzle diameters along the lip line of the 50.8 mm diameter jet. The cold flow data at Mach 0.5 were compared with hotwire anemometry measurements in order to validate the new TR-PIV technique. The axial turbulence profiles measured across the shear layer using TR-PIV were thinner than those measured using hotwire anemometry and remained centred along the nozzle lip line. The collected TR-PIV data illustrate the differences in the single point statistical flow properties of cold and hot jet flows. The planar, time-resolved velocity records were then used to compute two-point space–time correlations of the flow at the Mach 0.9 flow condition. The TR-PIV results show that there are differences in the convective velocity and growth rate of the turbulent structures between cold and hot flows at the same Mach number.

Temporally Resolved Particle Image Velocimetry↗
NASA NTRSDate not supplied

Heat-death by volcano - how Venus went rogue?

The idea of a habitable Venus epoch has gained traction in recent years via 1-D and 3-D General Circulation Modeling (GCM) efforts [1,2,3]. Although recent work has supported an alternative permanent hot and dry scenario [4]. However, the habitable scenario presents us with a conundrum - how does a terrestrial planet transform from temperate to hot-house? For decades it was proposed that the gradual brightening of the sun was the probable cause [5]. Yet 4 billion years ago Venus was receiving nearly 1.4 times the insolation that Earth receives today, and many studies have put Earth at the inner boundary of the habitable zone today [6]. The newer 3-D GCM efforts have demonstrated that if Venus had an early habitable period, that the cloud-albedo feedback responsible for maintaining temperate surface conditions [7] could still be in operation today. From this perspective increasing insolation through time cannot be an answer to the transition from habitable to hot-house. We propose that the 'Great Climate Transition' (GCT) was trigged by simultaneous large igneous provinces (LIPs) akin to those like the Siberian Traps responsible for the End Permian [8]. We have taken the most up to date LIP database for Earth [9] and characterized their distribution through time as random or nearly random. Next we initiate a large suite of Monte Carlo simulations based on this record and generate the likelihood for simultaneous, or environmentally overlapping events in this hypothetical setup. We find the probability of such events to be quite high, a probable cause for Venus' GCT, and a possible harbinger of things to come for Earth.

Venus↗
NASA NTRS1945

Comparison of Pitching Moments Produced by Plain Flaps and by Spoilers and Some Aerodynamic Characteristics of an NACA 23012 Airfoil with Various Types of Aileron

Sectional characteristics of airfoil having retractable slotted flap with plain, slot-lip, or retractable ailerons are presented for a large range of aileron deflections. The analysis indicated that pitching moments produced by spoilers were less positive than those produced by plain flaps of equal effectiveness, also that pitching moments created by the spoiler increased less with the Mach number than similar moments produced by plain flaps. Positive values of pitching moment decreased as devices were located nearer airfoil leading edge.

PITCHING MOMENTS - AIRFOILS↗
NASA NTRS1958

Investigation of Inlet Control Parameters for an External-internal-compression Inlet from Mach 2.1 to 3.0

Investigation of the control parameters of an external-internal compression inlet indicates that the cowl-lip shock provides a signal to position the spike and to start the inlet over a Mach number range from 2.1 to 3.0. Use of a single fixed probe position to control the spike over the range of conditions resulted in a 3.7-count loss in total-pressure recovery at Mach 3.0 and 0 deg angle of attack. Three separate shock-sensing-probe positions were required to set the spike for peak recovery from Mach 2.1 to 3.0 and angles of attack from 0 deg to 6 deg. When the inlet was unstarted, an erroneous signal was obtained from the normal-shock control through most of the starting cycle that prevented the inlet from starting. Therefore, it was necessary to over-ride the normal-shock control signal and not allow the control to position the terminal shock until the spike was positioned.

POSITIONING EQUIPMENT↗
NASA NTRS1965

Nasa research on the aerodynamics of jet vtol engine installations

This paper summarizes some of the more pertinent results of NASA investigations related to the aerodynamics of jet VTOL engine installations. It shows that there is a base loss in hovering due to suction forces creased on the underside of the fuselage by the entrainment of ambient air in the slipstream, and that the magnitude of this effect is related to the turbulence in the jet stream and its consequent rate of mixing with ambient air. It also shows that there are large lift losses and pitching moments due to jet-free-stream interference and that these characteristics can be significantly altered by proximity to the ground. And, finally, it shows that simple bellmouth inlets give good pressure recovery and low distortion for vertically mounted lift engines if the inlet lip radius is sufficiently large, but that such inlets are not suitable for windmill starting of the engines.

VTOL AIRCRAFT↗
NASA NTRS1966

O-rings with mylar back-up provide high- pressure cryogenic seal

Mylar lip type back-up ring installed in combination with three rubber O-rings seal the junctions between a tube stub and an adapter during high pressure gas flow at cryogenic to room temperatures. Mylar seals should not be used with oxygen under pressure or in the liquid state.

Funk, G. M.↗
NASA NTRS1969

Two-functional seal for hose connection

Seal, machined from a plastic material, prevents liquid hydrogen leakage from hose connectors. It serves as a block-type seal supporting maximum loading of the poppet with slight elastic deflection or as a lip-type seal that is deformed elastically in bending, tension, or compression by the seated poppet.

Richardson, M. B.↗
NASA NTRS1972

Tubing cutter

Replacement of opposing smooth rollers with appropriately grooved rollers in manual tubing cutter allows smooth severance of tubing of different diameters and eliminates raised lip around cut end.

Giandomenico, A.↗
NASA NTRS1971

Buckling analysis for axially compressed flat plates, structural sections, and stiffened plates reinforced with laminated composites

A classical buckling analysis is developed for stiffened, flat plates composed of a series of linked plate and beam elements. Plates are idealized as multilayered orthotropic elements. Structural beads and lips are idealized as beams. The loaded edges of the stiffened plate are simply-supported and the conditions at the unloaded edges can be prescribed arbitrarily. The plate and beam elements are matched along their common junctions for displacement continuity and force equilibrium in an exact manner. Offsets between elements are considered in the analysis. Buckling under uniaxial compressive load for plates, sections, and stiffened plates is investigated. Buckling loads are the lowest of all possible general and local failure modes, and the mode shape is used to determine whether buckling is a local or general instability. Numerical correlations with existing analysis and test data for plates, sections, and stiffened plates including boron-reinforced structures are discussed. In general correlations are reasonably good.

Viswanathan, A. V.↗