Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Li plating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

The formation of current sheets in the solar atmosphere

A simple model of the effect of slow photospheric motions on the coronal magnetic field is examined. In this model, a magnetic field is stretched between two conducting plates and slow tangential displacements of the plates cause the field to evolve quasi-statically. If the field is treated as a continuum, the interior magnetic topology is uniquely specified by the displacement of the boundaries, while the topology of a field made up of discrete flux tubes is not determined by the boundary displacement. Treating the field as a continuum, it is found that small perturbations of a constant vertical or weakly sheared field can come to an equilibrium free of singularities if the separation between the plates is finite.

Zweibel, Ellen G.↗

High resolution electron microscopy study of a high Cu variant of Weldalite (tm) 049 and a high strength Al-Cu-Ag-Mg-Zr alloy

Weldalite (trademark) 049 is an Al-Cu-Li-Ag-Mg alloy that is strengthened in artificially aged tempers primarily by very thin plate-like precipitates lying on the set of (111) matrix planes. This precipitate might be expected to be the T(sub 1) phase, Al2CuLi, which has been observed in Al-Cu-Li alloys. However, in several ways this precipitate is similar to the omega phase which also appears as the set of (111) planes plates and is found in Al-Cu-Ag-Mg alloys. The study was undertaken to identify the set of (111) planes precipitate or precipitates in Weldalite (trademark) 049 in the T8 (stretched and artificially aged) temper, and to determine whether T(sub 1), omega, or some other phase is primarily responsible for the high strength (i.e., 700 MPa tensile strength) in this Al-Cu-Li-Ag-Mg alloy.

Herring, R. A.↗

Aging Optimization of Aluminum-Lithium Alloy C458 for Application to Cryotank Structures

Compared with aluminum alloys such as 2219, which is widely used in space vehicle for cryogenic tanks and unpressurized structures, aluminum-lithium alloys possess attractive combinations of lower density and higher modulus along with comparable mechanical properties. These characteristics have resulted in the successful use of the aluminum-lithium alloy 2195 (Al-1.0 Li-4.0 Cu-0.4 Mg-0.4 Ag-0.12 Zr) for the Space Shuttle External Tank, and the consideration of newer U.S. aluminum-lithium alloys such as L277 and C458 for future space vehicles. These newer alloys generally have lithium content less than 2 wt. % and their composition and processing have been carefully tailored to increase the toughness and reduce the mechanical property anisotropy of the earlier generation alloys such 2090 and 8090. Alloy processing, particularly the aging treatment, has a significant influence on the strength-toughness combinations and their dependence on service environments for aluminum-lithium alloys. Work at NASA Marshall Space Flight Center on alloy 2195 has shown that the cryogenic toughness can be improved by employing a two-step aging process. This is accomplished by aging at a lower temperature in the first step to suppress nucleation of the strengthening precipitate at sub-grain boundaries while promoting nucleation in the interior of the grains. Second step aging at the normal aging temperature results in precipitate growth to the optimum size. A design of experiments aging study was conducted for plate. To achieve the T8 temper, Alloy C458 (Al-1.8 Li-2.7 Cu-0.3 Mg-0.08 Zr-0.3 Mn-0.6 Zn) is typically aged at 300F for 24hours. In this study, a two-step aging treatment was developed through a comprehensive 2(exp 4) full factorial design of experiments study and the typical one-step aging used as a reference. Based on the higher lithium content of C458 compared with 2195, the first step aging temperature was varied between 175F and 250F. The second step aging temperatures was varied between 275F and 325F, which is in the range of the single-step aging temperature. The results of the design of experiments used for the T8 temper as well as a smaller set of experiments for the T6 temper will be presented. The process of selecting the optimum aging treatment, based on the measured mechanical properties at room and cryogenic temperature as well as the observed deformation mechanisms, will be presented in detail. The implications for the use of alloy C458 in cryotanks will be discussed.

Sova, B. J.↗

Aging Optimization of Aluminum-Lithium Alloy C458 for Application to Cryotank Structures

Compared with aluminum alloys such as 2219, which is widely used in space vehicle for cryogenic tanks and unpressurized structures, aluminum-lithium alloys possess attractive combinations of lower density and higher modulus along with comparable mechanical properties. These characteristics have resulted in the successful use of the aluminum-lithium alloy 2195 (Al-1.0 Li-4.0 Cu-0.4 Mg-0.4 Ag-0.12 Zr) for the Space Shuttle External Tank, and the consideration of newer U.S. aluminum-lithium alloys such as L277 and C458 for future space vehicles. These newer alloys generally have lithium content less than 2 wt. % and their composition and processing have been carefully tailored to increase the toughness and reduce the mechanical property anisotropy of the earlier generation alloys such 2090 and 8090. Alloy processing, particularly the aging treatment, has a significant influence on the strength-toughness combinations and their dependence on service environments for aluminum-lithium alloys. Work at NASA Marshall Space Flight Center on alloy 2195 has shown that the cryogenic toughness can be improved by employing a two-step aging process. This is accomplished by aging at a lower temperature in the first step to suppress nucleation of the strengthening precipitate at sub-grain boundaries while promoting nucleation in the interior of the grains. Second step aging at the normal aging temperature results in precipitate growth to the optimum size. A design of experiments aging study was conducted for plate. To achieve the T8 temper, Alloy C458 (Al-1.8 Li-2.7 Cu-0.3 Mg- 0.08 Zr-0.3 Mn-0.6 Zn) is typically aged at 300 F for 24 hours. In this study, a two-step aging treatment was developed through a comprehensive 24 full factorial design of experiments study and the typical one-step aging used as a reference. Based on the higher lithium content of C458 compared with 2195, the first step aging temperature was varied between 175 F and 250 F. The second step aging temperatures was varied between 275 F and 325 F, which is in the range of the single-step aging temperature. The results of the design of experiments used for the T8 temper as well as a smaller set of experiments for the T6 temper will be presented. The process of selecting the optimum aging treatment, based on the measured mechanical properties at room and cryogenic temperature as well as the observed deformation mechanisms, will be presented in detail. The implications for the use of alloy C458 in cryotanks will be discussed.

Sova, B. J.↗

Li 3 PO 4 Matrix Enables a Long Cycle Life and High Energy Efficiency Bismuth-Based Battery

Bismuth is a lithium-ion battery anode material that can operate at an equilibrium potential higher than graphite and provide a capacity twice as high as that of Li 4 Ti 5 O 12 , making it intrinsically free from lithium plating that may cause catastrophic battery failure. However, the potential of bismuth is hampered by its inferior cyclability (limited to tens of cycles). Here, we propose an “ion conductive solid-state matrix” approach to address this issue. By homogeneously confining bismuth nanoparticles in a solid-state γ-Li 3 PO 4 matrix that is electrochemically formed in situ, the resulting composite anode exhibits a reversible capacity of 280 mA hours per gram (mA h/g) at a rate of 100 mA/g and a record cyclability among bismuth-based anodes up to 500 cycles with a capacity decay rate of merely 0.071% per cycle. We further show that full-cell batteries fabricated from this composite anode and commercial LiFePO 4 cathode deliver a stable cell voltage of ~2.5 V and remarkable energy efficiency up to 86.3%, on par with practical batteries (80–90%). This work paves a way for harnessing bismuth-based battery chemistry for the design of high capacity, safer lithium-ion batteries to meet demanding applications such as electric vehicles.

25 ENERGY STORAGE↗

NASICON Li 1.2 Mg 0.1 Zr 1.9 (PO 4 ) 3 Solid Electrolyte for an All‐Solid‐State Li‐Metal Battery

Abstract A thin solid electrolyte with a high Li + conductivity is used to separate the metallic lithium anode and the cathode in an all‐solid‐state Li‐metal battery. However, most solid Li‐ion electrolytes have a small electrochemical stability window, large interfacial resistance, and cannot block lithium‐dendrite growth when lithium is plated on charging of the cell. Mg 2+ stabilizes a rhombohedral NASICON‐structured solid electrolyte of the formula Li 1.2 Mg 0.1 Zr 1.9 (PO 4 ) 3 (LMZP). This solid electrolyte has Li‐ion conductivity two orders of magnitude higher at 25 °C than that of the triclinic LiZr 2 (PO 4 ) 3 . 7 Li and 6 Li NMR confirm the Li‐ions in two different crystallographic sites of the NASICON framework with 85% of the Li‐ions having a relatively higher mobility than the other 15%. The anode–electrolyte interface is further investigated with symmetric Li/LMZP/Li cell testing, while the cathode–electrolyte interface is explored with an all‐solid‐state Li/LMZP/LiFePO 4 cell. The enhanced performance of these cells enabled by the Li 1.2 Mg 0.1 Zr 1.9 (PO 4 ) 3 solid electrolyte is stable upon repeated charge/discharge cycling.

Zhou, Qiongyu↗

How Fast Can a Li-Ion Battery Be Charged? Determination of Limiting Fast Charging Conditions

Fast-charge protocols that prevent lithium plating are needed to extend the life span of lithium-ion batteries. Here, we describe a simple experimental method to estimate the minimum charging time below which it is simply impossible to avoid plating at a given temperature. We demonstrate that, by gauging and correcting the ohmic drop that is intrinsic to reference electrodes, the local potential at the anode surface can be reasonably approximated. This finer anode control enables the determination of the maximum average rate at which lithium deposition can be mitigated, establishing realistic boundaries that can inform the development of advanced charging protocols.

25 ENERGY STORAGE↗

Morphology-controlled LiFePO{sub 4} cathodes by a simple polyol reaction for Li-ion batteries

LiFePO{sub 4} cathodes with secondary nanorod structures and nano-plate morphologies were synthesized by varying the reaction time in a polyol refluxing process without the use of any characteristic structure directing agents. The X-ray diffraction studies indicate the highly crystalline nature of the prepared samples. Electron microscopy investigations revealed the morphology of the samples after 1 to 16 h polyol reaction to be secondary nanorod bundles whereas the olivine sample recovered after 32 h polyol reaction displayed nano-plate morphology. The dimensions of the obtained samples varied from a few tens to a few hundred nanometers. When employed in a lithium test cell, the LiFePO{sub 4} cathodes reacted for 1, 4, 8, 16 and 32 h delivered discharge capacities of 161, 162, 171, 143 and 155 mAhg{sup −1}, respectively, with a well-defined plateau at 3.4 V and impressive capacity retentions until 50 cycles. Interestingly, among the prepared electrodes, the LiFePO{sub 4} nanorod bundle cathode prepared under 1 h reaction time maintained the highest average reversible capacities of 123 and 103 mAhg{sup −1} at C-rates as high as 3.2 and 6.4 C. The crystal growth mechanism during the polyol refluxing method can be explained by the stages of precursor dissolution and nucleation, oriented crystal growth and alignment by self-assembly, aggregation and partial dissolution and complete re-crystallization. - Highlights: • Study of LiFePO{sub 4} crystal formation by tuning reaction times in a simple polyol process • Nano-structured LiFePO{sub 4} is formed by varying reaction times in a simple polyol process. • Self-assembled secondary LiFePO{sub 4} nanorod bundles are obtained under 1 h reaction time. • Secondary structures are formed via a template-free self-assembly process. • The olivine nanorod bundle cathode demonstrated enhanced electrochemical properties.

36 MATERIALS SCIENCE↗

Fabrication of hard x-ray zone plates with high aspect ratio using metal-assisted chemical etching

Fresnel zone plates are widely used as nanofocusing optics for x-ray microscopy, where the spatial resolution is set by the width of the finest rings while the efficiency is set by their thickness. This leads to the requirement for high aspect ratio nanofabrication. Metal-assisted chemical etching and atomic layer deposition has already been used to produce high aspect ratio zone plate structures on un-thinned silicon wafers. We demonstrate here a substantial improvement on the achieved aspect ratio up to a value of 500:1, by producing 16 nm wide platinum zones with thicknesses up to 8 µm. At the same time, the silicon substrate was thinned to 15 µm as required for a practically useful optic. First tests have shown 4.8% diffraction efficiency using 20 keV X rays. This x-ray focusing efficiency is higher than most Fresnel zone plates for this photon energy and near what has been achieved with multilayer-coated Kirkpatrick-Baez mirrors, and multilayer Laue lenses. Hard x-ray zone plates offer the advantages of easy alignment, energy tunability, and one can make many zone plates in a batch on a single silicon chip.

Fresnel zone plates↗

Experimental quantification of “hardenability” of 2195 and 2050 Al-Li alloys by using cold-rolled sheets

Highlights: • An experimental simulation method for intuitive “hardenability” evaluation. • With increasing the distance from the quenching end, the strength of 2050 alloy lowers more slowly than that of 2195 alloy, indicating its better “hardenability”. • At the location far away from the quenching end, lenticular-shaped phases form within grains, which impede T1 precipitation at the same local location during the following aging process. • More intra-granular lenticular-shaped phases in 2195 Al-Li alloy corresponds to its lower “hardenability”. - Abstract: To effectively and intuitively evaluate the “hardenability” during the design of new heat-treatable Al alloys, an experimental evaluation method by using cold-rolled thin sheets was proposed, which combined end-quenching with tensile test after aging, and eliminated the effect of different original structure of thick plate through-thickness. The “hardenability” of 2050 and 2195 Al-Li alloys was then intuitively characterized by their strength lowering as a function of distance away from the quenching end after T8-aging following end-quenching. As the distance is increased, the strength of the 2050 Al-Li alloy lowers more slowly than that of the 2195 Al-Li alloy, indicating a better “hardenability” of the 2050 Al-Li alloy. At the location with a certain distance away from the quenching end, in addition to the Cu-rich secondary phases at the grain boundary, lenticular-shaped Cu-containing secondary phases also form within grains during the end quenching process, which impede the precipitation of T1 (Al{sub 2}CuLi) phase at the same local location during the following aging process. More importantly, the number of the intra-granular lenticular-shaped phases in the 2195 Al-Li alloy is much more than that in the 2050 Al-Li alloy, which contributes to a less “hardenability” of the 2195 Al-Li alloy.

36 MATERIALS SCIENCE↗

Understanding the Reactivity of a Thin Li 1.5 Al 0.5 Ge 1.5 (PO 4 ) 3 Solid–State Electrolyte toward Metallic Lithium Anode

The thickness of solid-state electrolytes (SSEs) significantly affects the energy density and safety performance of all-solid-state lithium batteries. However, a sufficient understanding of the reactivity toward lithium metal of ultrathin SSEs (<100 μm) based on NASICON remains lacking. Herein, for the first time, a self-standing and ultrathin (70 μm) NASICON-type Li 1.5 Al 0.5 Ge 1.5 (PO 4 ) 3 (LAGP) electrolyte via a scalable solution process is developed, and X-ray photoelectron spectroscopy reveals that changes in LAGP at the metastable Li-LAGP interface during battery operation is temperature dependent. Severe germanium reduction and decrease in LAGP particle size are detected at the Li-LAGP interface at elevated temperature. As a result, oriented plating of lithium metal on its preferred (110) face occurs during in situ X-ray diffraction cycling.

25 ENERGY STORAGE↗

Unveiling mechanisms and onset threshold of humping in high-speed laser welding

The fabrication of fuel cells relies on a rapid laser welding process. However, challenges arise with the occurrence of humping when the welding speed surpasses a critical threshold, which poses difficulties in achieving a smooth surface finish and a consistent weld strength. This study aims to elucidate the humping mechanisms by analyzing the morphology of molten pool and the characteristics of melt flow at varying welding speeds via in situ synchrotron high-speed X-ray imaging and computational fluid dynamics simulations. Our findings indicate that the short keyhole rear wall, the high backward melt velocity, and the prolonged tail of molten pool are the primary factors contributing to the onset of humping. Furthermore, a dimensionless humping index (π h ) was introduced, which successfully captured the onset threshold of humping across different literatures. This index not only provides a quantitative description of the humping formation tendency but also serves as a valuable tool for optimizing the laser welding process.

42 ENGINEERING↗

Pathways towards managing cost and degradation risk of fast charging cells with electrical and thermal controls

The charging rate of Li-ion batteries is limited by the risks of lithium plating and thermal damage, both of which negatively affect lifetime of the batteries. This work analyzes how to minimize charge time and manage the risk of degradation using both electrical and thermal controls. To accomplish this, an electrochemical-thermal model is developed to introduce a constant-risk fast charging protocol which maximizes the charging current while maintaining the cell within pre-defined design limits selected to minimize the risk of degradation. Results indicate 80%-charging of a typical NMC/graphite cell can be achieved within 10 minutes with a cell cost under $100 kW –1 h –1 (corresponding to an 80 μm thick anode) when charged at moderate allowable risks of degradation. Here, we also demonstrate how stretching the allowable risk (i.e., higher temperatures, larger C-rates, and lower anode potential limits) allows affordable design of fast charging cells.

25 ENERGY STORAGE↗

Fracture toughness of an Al-Li-Cu-In alloy

The crack initiation and growth fracture toughness of select AL-Li-Cu alloy variants are characterized and elucidated. Conventionally processed plates form large DC cast ingots are investigated to eliminate the variation in microstructure associated with laboratory scale and SPF-processed material. Fracture resistance is characterized using the J-integral method to establish crack initiation and growth behavior at 25 and -185 C. It is shown that state-of-the-art 2090-T81 has superior toughness compared to 2090 + In-T6 at both test temperatures, with the low toughness of 2090 + In-T6 associated with intersubgranular fracture attributed to a high density of subboundary precipitates.

Wagner, John A.↗

Building interface bonding and shield for stable Li-rich Mn-based oxide cathode

Implementation of Li-rich Mn-based oxide cathode with high-energy-density has been restrained by capacity/voltage degradation that results from irreversible lattice oxygen loss and structure rearrangements. To resolve these challenges, in this work, Li 1.2 Mn 0.54 Ni 0.13 Co 0.13 O 2 encapsulated by amorphous Co x B (CB-LRM) is rationally designed via autocatalytic plating for highly reversible cationic/anionic hybrid cathode material. Band coherency is ingeniously evoked by interface-reconstruction between bulk structure and amorphous coating layer, which lower the energy of O $2p$ states. Furthermore, this is associated with strengthened orbital hybridization of O $2p$-Mn $3d$ and increased formation energy of oxygen vacancy, which mitigates the lattice oxygen loss considerably. Additionally, interface shielding effects that protect electrode against electrolyte corrosion and the reduction of surface oxygen are also present with fully coverage of amorphous Co x B coating layer. As a result, the as-designed CBLRM cathode exhibits excellent cycle stability after 100 loops with only 0.154% per cycle capacity fade and improved voltage degradation. Given this, this work provides a potential avenue for rational design of lattice oxygen-based electrode materials with high-energy-density.

25 ENERGY STORAGE↗

The Crucial Role of Vacancy Concentration in Enabling Superatomic Diffusion in Lithium Intermetallics

Anode-free solid-state Li batteries promise significant increases in energy densities compared to current commercial batteries that rely on liquid electrolytes. Major challenges persist in controlling morphological evolution during the plating and stripping of lithium metal at the anode current collector. Elemental additives that alloy with lithium have been found to modify the plating and stripping behavior of lithium. Many alloying elements form intermetallics with lithium and the mobility of Li through these intermetallics is believed to have an important effect on morphological evolution. This study shows that Li transport coefficients through intermetallics span a wide range in values, with the B32 LiAl intermetallic predicted to have a Li tracer diffusion coefficient as high as 10 –6 cm 2 /s at room temperature, which is 8 orders of magnitude larger than that of isostructural B32 LiZn. This work demonstrates the crucial role of vacancy concentration in controlling the mobility of Li atoms through intermetallics. While the migration barriers for Li-vacancy exchanges in both LiAl and LiZn are remarkably low, the superatomic conductivity in LiAl is shown to arise from the unique electronic structure of the B32 LiAl compound, which favors high concentrations of vacancies.

25 ENERGY STORAGE↗