Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LUBRICATING OIL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Gear Mesh Loss-of-Lubrication Experiments and Analytical Simulation

An experimental program to determine the loss-of-lubrication (LOL) characteristics of spur gears in an aerospace simulation test facility has been completed. Tests were conducted using two different emergency lubricant types: (1) an oil mist system (two different misted lubricants) and (2) a grease injection system (two different grease types). Tests were conducted using a NASA Glenn test facility normally used for conducting contact fatigue. Tests were run at rotational speeds up to 10000 rpm using two different gear designs and two different gear materials. For the tests conducted using an air-oil misting system, a minimum lubricant injection rate was determined to permit the gear mesh to operate without failure for at least 1 hr. The tests allowed an elevated steady state temperature to be established. A basic 2-D heat transfer simulation has been developed to investigate temperatures of a simulated gear as a function of frictional behavior. The friction (heat generation source) between the meshing surfaces is related to the position in the meshing cycle, the load applied, and the amount of lubricant in the contact. Experimental conditions will be compared to those from the 2-D simulation.

Handschuh, Robert F.↗
NASA NTRS2011

Gear Mesh Loss-of-Lubrication Experiments and Analytical Simulation

An experimental program to determine the loss-of-lubrication (LOL) characteristics of spur gears in an aerospace simulation test facility has been completed. Tests were conducted using two different emergency lubricant types: (1) an oil mist system (two different misted lubricants) and (2) a grease injection system (two different grease types). Tests were conducted using a NASA Glenn test facility normally used for conducting contact fatigue. Tests were run at rotational speeds up to 10000 rpm using two different gear designs and two different gear materials. For the tests conducted using an air-oil misting system, a minimum lubricant injection rate was determined to permit the gear mesh to operate without failure for at least 1 hr. The tests allowed an elevated steady state temperature to be established. A basic 2-D heat transfer simulation has been developed to investigate temperatures of a simulated gear as a function of frictional behavior. The friction (heat generation source) between the meshing surfaces is related to the position in the meshing cycle, the load applied, and the amount of lubricant in the contact. Experimental conditions will be compared to those from the 2-D simulation.

Handschuh, Robert F.↗
NASA NTRS2003

NASA PS304 Lubricant Tested in World's First Commercial Oil-Free Gas Turbine

In a marriage of research and commercial technology, a 30-kW Oil-Free Capstone microturbine electrical generator unit has been installed and is serving as a test bed for long-term life-cycle testing of NASA-developed PS304 shaft coatings. The coatings are used to reduce friction and wear of the turbine engine s foil air bearings during startup and shut down when sliding occurs, prior to the formation of a lubricating air film. This testing supports NASA Glenn Research Center s effort to develop Oil-Free gas turbine aircraft propulsion systems, which will employ advanced foil air bearings and NASA s PS304 high temperature solid lubricant to replace the ball bearings and lubricating oil found in conventional engines. Glenn s Oil-Free Turbomachinery team s current project is the demonstration of an Oil-Free business jet engine. In anticipation of future flight certification of Oil-Free aircraft engines, long-term endurance and durability tests are being conducted in a relevant gas turbine environment using the Capstone microturbine engine. By operating the engine now, valuable performance data for PS304 shaft coatings and for industry s foil air bearings are being accumulated.

Weaver, Harold F.↗
NASA NTRS1979

Wear of aluminum and hypoeutectic aluminum-silicon alloys in boundary-lubricated pin-on disk sliding

The friction and wear of pure aluminum and a number of hypoeutectic aluminum-silicon alloys (with 3 to 12 wt %Si) were studied with a pin-on-disk apparatus. The contacts were lubricated with mineral oil and sliding was in the boundary-lubrication regime at 2.6 cm/sec. Surfaces were analyzed with photomicrographs, scanning electron microscopy, X-ray dispersive analysis, and diamond pyramid hardness measurements. There were two wear regimes for the alloys - high and low - whereas pure aluminum exhibited a high wear rate throughout the test period. Wear rate decreased and the transition stress from high to low wear increased with increasing hardness. There was no correlation between friction coefficient and hardness. A least squares curve fit indicated a wear-rate dependence greater than the inverse first power of hardness. The lower wear rates of the alloys may be due to the composites of silicon platelets in aluminum resulting in increased hardness and thus impairing the shear of the aluminum.

Ferrante, J.↗
NASA NTRS1978

Oil Saving Seal

Driven under difficult field conditions, the Army Jeep shown went more than 22,000 miles without an oil change in a test conducted by the U.S. Army Mobility Equipment Research and Development Command. Key to this exceptionally long oil life was a set of piston ring seals made of a new synthetic rubber formula called RC-34; the seal pictured, photographed after its arduous Army trial, shows no signs of deterioration. The seal and the RC-34 material, which may soon be available for use in the family auto, were developed by Ramsey Corporation, St. Louis, Missouri, a division of TRW Automotive Worldwide. The oil in an automobile engine must be I replaced every few thousand miles not because it wears out but because it becomes contaminated. The contamination sources are gasoline and combustion gases which blow by the piston rings to mix with the oil, reducing the oil's ability to lubricate properly. Seeking to prolong oil life by eliminating "blowby," Ramsey Corporation looked for a better way to seal piston rings and used NASA technology as a departure point. The parent company TRW, under contract to NASA's Jet Propulsion Laboratory, had developed seals and bladders from a type of material called elastomers which where designed to withstand the environmental extremes of interplanetary flight. That effort formed a knowledge base for research which culminated in Ramsey's RC-34 elastomer.

Source record↗
NASA NTRS2009

Nitinol 60 as a Material For Spacecraft Triboelements

The mechanical properties of Nitinol 60, 60 w/o Ni, 40 w/oTi (55 a/o Ni, 45 a/o Ti) are sufficiently attractive to warrant its consideration as a lubricated spacecraft triboelement. The ability to lubricate Nitinol 60 by the oils usually used on spacecraft mechanisms--Pennzane 2001A, Krytox 143AC and Castrol 815Z - was experimentally determined. These oils were run in the boundary lubrication regime for Nitinol 60 balls running against a 440C steel counterface in the vacuum spiral orbit tribometer. Test results consisting of the coefficient of friction versus time (friction traces) and relative degradation rates are presented. Contrary to the inability to successfully lubricate other metal alloys with high titanium content, it was found that Nitinol 60 is able to be lubricated by these oils. Overall, the results presented here indicate that Nitinol 60 is a credible candidate material for spacecraft bearing applications.

Pepper, Stephen V.↗
NASA NTRS1994

Evaluation of PS 212 Coatings Under Boundary Lubrication Conditions with an Ester-based Oil to 300 C

High friction and wear of turbine engine components occur during high temperature excursions above the oxidation threshold of the liquid lubricant. This paper reports on research to study the use of a high temperature self lubricating coating, PS 212 for back-up lubrication in the event of failure of the liquid lubricant. Pin on disk tests were performed under dry and boundary-lubricated conditions at disk temperatures up to 300 C. The liquid lubricant was a formulated polyol ester qualified under MIL L-23699. At test temperatures above the oil's thermal degradation level, the use of PS 212 reduced wear, providing a back-up lubricant effect.

Sliney, Harold E.↗
NASA NTRS2010

Lubrication of Nitinol 60

The mechanical properties of Nitinol 60, 60 wt% Ni, 40 wt% Ti (55 at.% Ni, 45 at.% Ti) are sufficiently attractive to warrant its consideration as a lubricated triboelement. Triboelements are always run lubricated. The ability to lubricate Nitinol 60 by the oils usually used on spacecraft mechanisms--Pennzane 2001A, Krytox 143AC and Castrol 815Z--was experimentally determined. These oils were run in the boundary lubrication regime for Nitinol 60 balls running against Nitinol 60 counterfaces in the vacuum spiral orbit tribometer. Test results consisting of the coefficient of friction versus time (friction traces) and relative degradation rates of the oils are presented. Contrary to the inability to successfully lubricate other metal alloys with high titanium content, it was found that Nitinol 60 is able to be lubricated by these oils. Overall, the results presented here indicate that Nitinol 60 is a credible candidate material for bearing applications.

Pepper, Stephen V.↗
DOE OSTI2025

Investigations on the Thermal Stability and Kinetics of Biolubricants Synthesized from Different Types of Vegetable Oils

Petroleum-based lubricants raise environmental concerns due to their non-biodegradability and toxicity, whereas biobased lubricants underperform owing to low thermal stability. This study examined and compared three vegetable oils, along with their chemically modified versions, to better understand their suitability as biolubricants. High oleic soybean oil (HOSOY), regular soybean oil (RSOY), and waste cooking oil (WCO) were subjected to chemical modification, where isopropyl groups were attached to the fatty acid chains of the oils to produce branched oils, i.e., b-HOSOY, b-RSOY, and b-WCO. The detailed kinetic study of each regular and modified sample was investigated using thermogravimetric analysis. The kinetic parameters, such as the activation energies, reaction rate, and pre-exponential factor, were generated via Friedman methods. The differential thermal gravimetric (DTG) analysis showed low volatilization at the onset temperature in each modified oil as compared with the unmodified samples under an oxidative environment. Furthermore, the comparative kinetic studies demonstrated the enhanced thermoxidative stability of the modified products relative to their unaltered counterparts. Among the tested oils, the b-RSOY showed an average activation energy of 325 kJ/mol, followed by the b-WCO: 300 kJ/mol and the b-HOSOY: 251 kJ/mol, indicating the most stable modified product under an oxidative environment. For all the samples, the pre-exponential factors were in good agreement with the activation energies, which validates that finding the pre-exponential components is crucial to the kinetic analysis.

Sarker, Majher I. (ORCID:0000000299509274)↗
NASA NTRS1987

Dynamic characterization of viscoelastic polymer solutions in a lubricated cylinder - Plate apparatus

The characterization of several viscoelastic lubricants which are oil or water based has been studied in an apparatus consisting of a lubricated cylinder-plate contact. The friction loads were measured as a function of speed. The experimental results show the influence of the molecular weight and of the concentration of the polymeric additive as well as the influence of the viscosity of the oil-base on the load and friction coefficient. Also a test for mechanical degradation was performed on the polymer solutions. Several additives can favor a viscoelastic lubrication.

Doremus, P.↗
NASA NTRS1973

Interdisciplinary Approach to Liquid Lubricant Technology

The proceedings of a conference of liquid lubricant technology are presented. The subjects discussed are: (1) requirements and functions of liquid lubricants, (2) mineral oils, (3) greases, (4) theory of rheology, (5) mechanics and thermodynamics in lubrication, (6) environmental capability of liquid lubricants, and (7) wear corrosion and erosion.

Ku, P. M.↗
DOE OSTI2021

Lignin monomer conversion into biolubricant base oils

Despite progress in the depolymerization of lignin, only a few studies convert the obtained monomers to value-added products. Here we introduce a strategy to synthesize branched benzene lubricant (BBL) and branched cyclic lubricant (BCL) base oils from lignin-derived monomers and aldehyde. We perform carbon–carbon coupling via Brønsted acid-catalyzed hydroxyalkylation/alkylation (HAA) then hydrodeoxygenation (HDO). Optimum HAA reaction conditions achieve up to 90% guaiacol conversion and an HAA product containing 76% BBL and 24% enal condensation product over a P-SiO 2 catalyst. Subsequent HDO of HAA products over an Ir-ReO x /SiO 2 catalyst produces a lubricant-ranged mixture of BCL (C 24 ) up to yield (82%) and small fractions of dodecyl cyclohexane and C 10 and C 15 carbons alkanes. The kinematic viscosity, viscosity index, and Noack volatility of these base oils are comparable to commercial petroleum-derived poly α-olefin Group IV and refrigerant base oils. In conclusion, this approach provides a sustainable pathway for replacing petroleum-derived base oils.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Development of Ionic Liquid-Additized, GF-5/6 Compatible Low-Viscosity Oils for Automotive Engine and Rear Axle Lubrication for 4% Improved Fuel Economy

This joint project among ORNL, GM, and DRO successfully developed ionic liquid-additized low viscosity lubricants, SAE 0W-12 and 70W-80, for both IC engine and rear axle lubrication, respectively, and demonstrated combined vehicle fuel economy improvement (FEI). Phosphonium-alkylphosphate ILs have been found to be the most effective among the candidates in protecting surface damage from both sliding wear and rolling contact fatigue, and optimal IL concentrations have been determined. The IL’s impact on three-way catalyst seems to be significantly less adverse than the conventional ZDDP. Oil formulations were optimized for both energy efficiency and wear protection. Tribological bench testing of the IL-additized low-viscosity oils showed at least 40% lower boundary friction, more than 60% lower elastohydrodynamic friction, and greater than 50% less wear compared with commercial baselines. IL-additized lubricants have demonstrated FEI by 9.9% in engine dynamometer tests under extreme conditions and 6.9% increased power output in gear rig tests. Prototype IL-additized engine oil and rear axle fluid exhibited combined FEI of 1.39% and 3.24% benchmarked against the state-of-the-art baselines in vehicle testing of fresh oils under the Federal Test Procedure (FTP) city cycle and Highway Fuel Economy Driving Schedule (HWFET), respectively. Used oil analysis suggested that the IL-additized low-viscosity oils produced less wear than the commercial baselines. The gained fundamental understanding and demonstrated FEI in this work pave the way for future development and implementation of the ionic liquid technology.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1990

Positive lubrication system

As part of the development of an autonomous lubrication system for spin bearings, a system was developed to deliver oil to grease-lubricated bearings upon demand. This positive oil delivery system (PLUS) consists of a pressurized reservoir with a built-in solenoid valve that delivers a predictable quantity of oil to the spin bearing through a system of stainless steel tubes. Considerable testing was performed on the PLUS to characterize its performance and verify its effectiveness, along with qualifying it for flight. Additional development is underway that will lead to the fully autonomous active lubrication system.

Smith, Dennis W.↗
NASA NTRS1990

X-ray photoelectron spectroscopy peak assignment for perfluoropolyether oils

Perfluoroalkylpolyether (PFPE) oils are increasingly being used as vacuum pump oils and as lubricants for magnetic recording media and instrumentation for satellites. In this paper, the relative binding energies of three PFPE oils are determined. When sample oils are continuously irradiated during X-ray spectroscopy (XPS) measurements, the relative peak intensity of the spectra is altered significantly, indicating that gaseous products form from the oils during XPS measurements. Thus, attention should be paid to chemical changes when XPE is used to characterize fluorinated carbons such as PFPE oils.

Mori, Shigeyuki↗