Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Jettison”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS2018

Reducing Hazards of Propulsive Secondary Payloads by Implementing a Post Launch Pressurization System

Propulsion systems on SmallSats and CubeSats are becoming more common as launch vehicles like SLS begin providing rideshares to destinations beyond low earth orbit. While these spacecraft are a solution to achieve advanced science objectives at lower cost, they are still subject to the same rigorous standards as other larger spacecraft, such as NASA STD-5019, due to the high pressures within their propulsion systems at launch. A Post Launch Pressurization System would allow a spacecraft to be launched at low pressure, then be pressurized through the controlled chemical decomposition of a solid reactant after the spacecraft is jettisoned from the launch vehicle. This increases the safety of the secondary spacecraft, and effectively mitigates risks to the launch vehicle and other payloads.

Perry, McKynzie↗
NASA NTRS2018

Studies in Support of Venus Aerocapture Utilizing Drag Modulation

Aerocapture has been extensively studied and these studies have shown the benefit for planetary exploration missions. While the traditional approach to aerocapture with lifting configurations and lift-guided modulations have been assessed to be technologically feasible, aerocapture using purely drag modulation was proposed and studied by Prof. Braun and his students. These studies show that if one can assess the feasibility of aerocapture using drag modulation at Venus, and develop tall pole technologies needed at Venus, then this concept is much easier to execute at all other relevant destinations. Based on the above finding, partnered proposals were submitted by Adam Nelessen at JPL and Ethiraj Venkatapathy at Ames in collaboration with Prof. Braun at the University of Colorado, Boulder (UCB). Under this partnership, Ames Research Center (ARC) is working to address some of the key entry technology challenges associated with drag modulation aerocapture at Venus. Drag modulation aerocapture is a simple, scalable, and likely cost-effective way to enhance planetary science missions. The approach envisioned is to design a small spacecraft, that would most likely be a secondary payload, with a removable drag skirt. The vehicle would enter the atmosphere at Venus with a low ballistic coefficient, decelerate rapidly, drop the skirt resulting in a smaller vehicle with a higher ballistic coefficient which would skip out of the atmosphere and enter into a desired orbit. ARC's role in this collaboration is multifold. First of which is to perform design studies on various pre- and post-jettison geometries utilizing a 3-DOF trajectory code to determine the aerodynamics and aerothermodynamics of the vehicles and evaluate viable thermal protection material system designs. Once these design studies are complete, Ames will then perform higher fidelity CFD and TPS sizing to further design the vehicles. Second, the multi-body separation dynamics of the drag modulation event will be explored using both CFD simulations (CART3-D and US3D) as well as possible ballistic range testing. ARC's tools and expertise have been used to assess and advise on the selection of the separating configuration. In addition to the preliminary evaluation, ARC will provide tools and expertise to UCB team members to further assess aerodynamic interactions between the separating bodies and provide guidance as to the feasibility of stable transition.

Beck, Robin↗
NASA NTRS2018

Adaptive Deployable Entry Placement Technology (ADEPT) Development for Small Sat Class Venus Missions

The Adaptable, Deployable Entry and Placement Technology (ADEPT) is a novel approach for entry vehicle design. Similar to an umbrella, it is stowed during launch and deployed prior to entry. ADEPT employs a high performance, 3-D woven, carbon fabric to serve as the primary surface of the mechanically deployed system. The successful ADEPT sounding rocket flight test matured the 1-meter Class ADEPT in the areas of deployment and structural integrity, and provided aerodynamic flight characteristics of the ADEPT open-back configuration from Mach 3 to Mach 0.3. Aerocapture uses the aerodynamic drag from a single hyperbolic atmospheric pass to provide the delta-V needed for orbit insertion. Studies suggest that, compared to propulsive orbit insertion, aerocapture could increase delivered payload by 70 percent at Venus. Drag modulation aerocapture, which shows promise of being simpler and more cost-effective than the more-often studied lift modulation methods, uses in-flight transformations of an entry vehicle's drag area to control the amount of deceleration produced during an atmospheric pass. In single-event drag modulation, a drag device is jettisoned after the appropriate deceleration. ADEPT, due to its unique ability to fold and unfold, is being considered for this SmallSat class payload mission applications.

Cassell, Alan M.↗
NASA NTRS2015

SOAREX-8 Suborbital Experiments 2015 - A New Paradigm for Small Spacecraft Communication

In 2015 NASA plans to launch a payload to 280 Km altitude on a sounding rocket from the Wallops Flight Facility. This payload will contain several novel technologies that work together to demonstrate methodologies for space sample return missions and for nanosatellite communications in general. The payload will deploy and test an Exo-Brake, which slows the payload aerodynamically, providing eventual de-orbit and recovery of future ISS samples through a Small Payload Quick Return project. In addition, this flight addresses future Mars mission entry technology, space-to-space communications using the Iridium Short Messaging Service (SMS), GPS tracking, and wireless sensors using the ZigBee protocol. SOAREX-8 is being assembled and tested at Ames Research Center (ARC) and the NASA Engineering and Safety Center (NESC) is funding sensor and communications work. Open source Arduino technology and software are used for system control. The ZigBee modules used are XBee units that connect analog sensors for temperature, air pressure and acceleration measurement wirelessly to the payload telemetry system. Our team is developing methods for power distribution and module mounting, along with software for sensor integration, data assembly and downlink. We have demonstrated relaying telemetry to the ground using the Iridium satellite constellation on a previous flight, but the upcoming flight will be the first time we integrate useful flight test data from a ZigBee wireless sensor network. Wireless sensor data will measure the aerodynamic efficacy of the Exo-Brake permitting further on orbit flight tests of improved designs. The Exo-Brake is 5 sq m in area and will be stored in a container and deployed during ascent once the payload is jettisoned from the launch vehicle. We intend to further refine the hardware and continue testing on balloon launches, future sounding rocket flights and on nanosatellite missions. The use of standards-based and open source hardware/software has allowed for this project to be completed with a very modest budget and a challenging schedule. There is a wealth of hardware and software available for both the Arduino platform and the XBee, all low-cost or open-source. Along with the Exo-Brake hardware and deployment discussion, this paper will describe in detail the system architecture emphasizing the successful use of open source hardware and software to minimize effort and cost. Testing procedures, radio frequency interference (RFI) mitigation, success criteria and expected results will also be discussed. The use of Iridium short messaging capability for space-to-space links, standards-based wireless sensor networks, and other innovative communications technology are also presented.

aerobrake↗
NASA NTRS2019

Powering OSCAR

Recycling waste has been an issue on Earth for decades. The OSCAR project seeks to find ways to make sure that it does not become an issue in space. The main focus of OSCAR is the combustion of waste and reclamation of gaseous products in microgravity. The first phase of testing relies on a ground rig that operates both under normal (Earth) gravity and in drop tower tests that briefly simulate a microgravity environment. In the second phase, a test will be performed during a suborbital flight were the experiment will be carried out in microgravity. Throughout the spring term, interns have played an integral part in continuing the progress made by the project. They performed work in upgrading the electrical and mechanical systems that make up OSCAR. They made multiple improvements to the test rig's operating software to improve readability and usability. They prepared and edited documents that were vital to the engineering process. And, they were responsible for performing lab tests and refining the lab operations document and procedure. The interns were a big help in maintaining the rigorous test schedule. OSCAR, which stands for Orbital Syngas Commodity Augmentation Reactor, is to find a way to turn astronaut waste into chemical energy. The two parts of this are important: finding a way to dispose of waste generated in space, and seeing if there is a way to recycle that waste into chemical energy. The importance of the disposal aspect is that there is currently no way to dispose of, or recycle, waste that is created in space other than jettisoning it (which is what the ISS does via empty supply capsules). As manned missions go deeper into space, that method will no longer be viable, as a craft would essentially be littering the space and planets that they visit. Energy reclamation is also important because of the high monetary and spatial costs of sending supplies on space missions. Every little bit extra that can be reused out of what is sent can save room and funds for other supplies. The facet of this problem that the OSCAR project is focusing on is how to combust waste in zero gravity. Combustion in the presence of gravity is one of those things that is taken for granted. When something burns on Earth, the flames rise above the fuel as oxygen flows from underneath. In microgravity, the flames surround the object completely, which restricts the amount of oxygen that can reach the fuel, and retards the combustion. OSCAR uses a vortex reaction chamber to counter this phenomenon. The OSCAR test rig will eventually be tested on a suborbital flight to see if it is an effective solution to the issue in real-world conditions. Currently, there is a prototype test rig that is fully functional. This rig has been previously tested in a 2 second drop test at Glenn Research Center’s (GRC) Zero Gravity Facility (ZGF). (The free-fall conditions of the drop mimic microgravity, if only for a brief period of time). This session’s focus was on upgrading the test rig and software, updating the paperwork, performing additional lab tests, and readying the rig for the five second drop test, again at GRC. II. Upgrades The state of the testing rig at the start of the session was in between its configurations for the two second drop tower and the five second drop tower. The rig needed upgrades to address various insufficiencies that either were discovered during the two second campaign or were a direct result of the differences between the two drop tower setups. The main differences that had to be handled were the increase in shock loads from 30g to 65g, a difference in drop indicating signal (on the falling edge of a pulse instead of a change from high to low), and the ambient pressure of the test apparatus (the two second tower dropped the rig in atmosphere, while the five second tower drops in vacuum).

Cauvel, Thomas↗
NASA NTRS2018

TES-8: Advanced Exo-Brake, VR and COM Experiments

The TES-8 was jettisoned from the International Space Station on January 31, 2019. As an orbital laboratory and 8th in on-going series, the design makes use of a standard set of interfaces and safety features that permit rapid re-flight. On this flight, an advanced Exo-Brake is flown with de-orbit targeting capability that will engender sample return capability from LEO platforms. A Virtual Reality data recording system uses stereo imaging and efficient data-compression with an NVIDIA GPU (Graphics Processing Unit) to permit compression and transmission of very large data files. An SDR (Software Defined Radio) will download data to the NEN (Near Earth Network) for the first time - demonstrating potential use in cis-lunar space using S-band. For the first time, a comparison will be made regarding the functionality of the Iridium and Globalstar short burst data modems - as essential communication tools for future nano-sat projects. Lastly, the 7 micro-processors and 4 cameras provide an excellent learning platform for university students and NASA young professionals.

Exo-Brake↗
NASA NTRS2019

Lessons Learned from the Flight Unit Testing of the Near Earth Asteroid Scout Flight System

The Near Earth Asteroid Scout flight mission is set to launch on the maiden voyage of the Space Launch System as a secondary payload. The spacecraft will be jettisoned in cis-lunar space and embark on an ambitious 2.5 year mission to image an asteroid. The spacecraft is uniquely equipped with an 85m2 solar sail as the main propulsion system. The monolithic sail system is designed to package within a 6U volume for launch and then deploy during flight. The NEA Scout team has presented in the past to the International Symposium on Solar Sailing topics related to the engineering development unit and design efforts to achieve flight hardware build. This paper will focus on the lessons learned from building and testing the NEA Scout flight system. Focus will be on the mechanical, software, and electrical interfaces as well as preparation for subsystem environmental tests, including thermal vacuum. Due to the unique design of the spacecraft, the solar sail subsystem was required to be located in the center of the spacecraft. This requirement lead to design challenges such as designing and accommodating critical cable harnesses to run through the center of the sail subsystem, packaging and deployment design of the sail subsystem, and integrated testing efforts through an avionics test bed to verify and validate a complete system architecture.

Lockett, Tiffany Russell↗
NASA NTRSDate not supplied

Variational Coupled Loads Analysis using the Hybrid Parametric Variation Method

Time-domain coupled loads analysis (CLA)is used to determine the response of a launch vehicle and payload system to transient forces, such as liftoff, engine ignitions and shutdowns, jettison events, and atmospheric flight loads, such as buffet. CLA, using Hurty/Craig-Bampton (HCB)component models, is the accepted method for the establishment of design-level loads for launch systems. However, uncertainty in the component models flows into uncertainty in predicted system results. Uncertainty in the structural responses during launch is a significant concern because small variations in launch vehicle and payload mode shapes and their interactions can result in significant variations in system loads. Uncertainty quantification (UQ)is used to determine statistical bounds on prediction accuracy based on model uncertainty. In this paper uncertainty is treated at the HCB component-model level. In an effort to account for model uncertainties and statistically bound their effect on CLA predictions, this work combines CLA with UQ in a process termed variational coupled loads analysis (VCLA). The modeling of uncertainty using a parametric approach, in which input parameters are represented by random variables, is common, but its major drawback is the resulting uncertainty is limited to the form of the nominal model. Uncertainty in model form is one of the biggest contributors to uncertainty in complex built-up structures. Model-form uncertainty can be represented using a nonparametric approach based on random matrix theory (RMT). In this work, UQ is performed using the hybrid parametric variation (HPV)method, which combines parametric with nonparametric uncertainty at the HCB component model level. The HPV method requires the selection of dispersion values for the HCB fixed-interface (FI)eigenvalues, and the HCB mass and stiffness matrices. The dispersions are based upon component test-analysis modal correlation results. During VCLA, random component models are assembled into an ensemble of random systems using a Monte Carlo (MC)approach. CLA is applied to each of the ensemble members to produce an ensemble of system-level responses for statistical analysis. The proposed methodology is demonstrated through its application to a buffet loads analysis of NASA’s Space Launch System (SLS)during the transonic regime fifty seconds after liftoff. Core stage (CS)section shears and moments are recovered, and statistics are computed.

Uncertainty Quantification↗
NASA NTRS2020

Experimental Investigation of Drag Modulation Aerocapture: Drag-Skirt Separation in Hypersonic Free Flight

Free flight tests were conducted in carbon dioxide at Mach 12 of notional drag modulation aerocapture configurations for a small satellite mission to Venus. The configurations were based on research conducted at the Georgia Institute of Technology, University of Colorado Boulder, Jet Propulsion Laboratory, and Ames Research Center. The drag modulation aerocapture approach being studied involves an atmospheric entry vehicle that employs an attached drag device, a drag skirt, that is jettisoned at the appropriate time to allow the payload-portion of the vehicle to exit the atmosphere, slowed enough to be captured into orbit. A total of eight tests were performed. Reynolds numbers, based on the pre-separation base diameter, ranged from 0.82 x 106 to 2.96 x 106. The tests demonstrated the feasibility of a clean drag skirt separation at hypersonic speeds and, for the conditions of the tests, the stability of the central flight system body during and after separation from the drag skirt. Two drag skirt geometries were tested: an axisymmetric conical frustum, and a faceted frustum representative of a mechanically-deployable device. Drag skirts of various masses were tested to examine the effect of pre- and post-separation ballistic coefficient ratio on the separation dynamics. A new test capability for multi-body interactions in hypersonic free flight was developed for these tests, and is described.

aerocapture↗
NASA NTRSDate not supplied

Parametric Studies of Human Mars Entry, Descent, and Landing Systems

This paper will present a parametric analysis for entry, descent, and landing (EDL) concepts, enabling rapid systems assessment and tradespace exploration. The entry system uses a hypersonic inflatable aerodynamic decelerator (HIAD) technology. The baseline system includes elements for Mars aerocapture (AC) and EDL segments of the mission. The mission concept of operations (ConOps) begins at Mars arrival in a polar inclination. After performing an aerocapture (AC) maneuver into a pre-defined Mars parking orbit, the AC HIAD is jettisoned. The rest of thevehicle stays in the parking orbit for up to one year. The EDL sequence starts with a deorbit burn at the apoapsis of the parking orbit. After hypersonic entry with the EDL HIAD, the entry system uses a supersonic retropropulsion maneuver to slow the vehicle for the descent and landing segments of the mission. The vehicle will maintain a constant velocity of 2.5 m/s for 5 seconds prior to landing.The system includes a Mars Ascent Vehicle (MAV), Mars Descent Module (MDM), and two HIADs. The MDM includes a primary structure, tanks, engines, and radiators. The primary structure is an aluminum-lithium (Al-Li)cruciform design similar to the structural design of the Apollo Lunar Module. The cruciform planform layout results in four outer bays, with adequate volume in the corners between outer bays to package four landing gears. The central bay is reserved for packaging the MAV and the recessed MAV engines. Two of the outer bays accommodate main propellant tanks, with one LOX and one CH4 tank in each bay. The two remaining outer bays each house four rocket engine systems and associated support structure. Each HIAD comprises an inflatable structure, flexible thermal protection system, gas, and gas generators. The HIAD design used in this study is a stacked-toroid concept with pairing loop straps and radial/chevron straps. The baseline system lands a 20-t payload on the Mars surface. It is assumed the vehicle arrives at 6.2 km/s relative velocity at 90° inclination and is captured to a 1-Sol parking orbit.The baseline design includes many assumptions such as margins, arrival state, ConOps options, parking orbit, physical dimensions, propellant options, and technology concepts. The impact of these parameters are quantified through systems-level sensitivity analyses, which capture the global impact—not at a component level—but at the systems level. The systems-level sensitivities expose major design drivers and importance of each assumption for a design.Through tradespace exploration, a wide range of systems parameters are examined and compared for several feasible design options. Studies have been completed for the following input parameters: payload mass, propellant options, AC/EDL ballistic coefficient, lander thrust to weight ratio (T/W) (surrogate for the maximum EDL g’s),engine specific impulse (Isp), parking orbit, and inclination.The final paper will present and discuss the parametric approach used in the study. It will also include the results of recent systems analyses, sensitivity analyses, and tradespace exploration

Jamshid Samareh↗
NASA NTRSDate not supplied

Supercritical Water Oxidation (SCWO) for the treatment of spacecraft waste.

Supercritical water oxidation (SCWO) is a powerful waste treatment that has been considered as a substitute or complement to other potential spacecraft waste handling methods including jettisoning, compacted sealed storage, drying, and others. Combustible trash and garbage is mixed with water and then heated and pressurized above the critical point of water (705 °F and 218 atmospheres). The waste is nearly all oxidized to produce carbon dioxide, water and nitrogen. NOx is not formed. The combustion energy can be used to heat the input stream. SCWO is relatively complex, expensive, and hazardous compared to other methods. Oxidation of compounds containing chlorine and sulfur produces hydrochloric and sulfuric acid which can cause corrosion in the reactor. Neutralizing these acids produces salts which can precipitate and cause clogging. The major engineering challenges to implementing SCWO are chemical corrosion and fouling due to the deposition of salts. SCWO was first proposed for general waste treatment and for spacecraft in the 1980’s and extensive research has been carried out.

Harry W Jones↗
NASA NTRS2004

Genesis failure investigation report

On January 7, 2001, the Genesis spacecraft lifted off from Cape Canaveral. Its mission was to collect solar wind samples and return those samples to Earth for detailed analysis by scientists. The mission proceeded successfully for three-and-a-half years. On September 8, 2004, the spacecraft approached Earth, pointed the Sample Return Capsule (SRC) at its entry target, and then fired pyros that jettisoned the SRC. The SRC carried the valuable samples collected over the prior 29 months. The SRC also contained the requisite hardware (mechanisms, parachutes, and electronics) to manage the process of entry, descent, and landing (EDL). After entering Earth’s atmosphere, the SRC was expected to open a drogue parachute. This should have been followed by a pyro event to release the drogue chute, and then by a pyro event to deploy the main parachute at an approximate elevation of 6.7 kilometers. As the SRC descended to the Utah landing site, helicopters were in position to capture the SRC before the capsule touched down. On September 8, 2004, observers of the SRC’s triumphant return became concerned as the NASA announcer fell silent, and then became even more alarmed as they watched the spacecraft tumble as it streaked across the sky. Long-distance cameras clearly showed that the drogue parachute had not deployed properly.

UNKNOWN↗
NASA NTRSDate not supplied

Hold Down and Release Mechanism Hardware Simulator for Ground Deployment Testing

Hold Down and Release Mechanisms (HDRMs) are a common piece of spacecraft hardware which restrain components during launch, transit, and later allow them to be extended, jettisoned, separated, etc. at the spacecraft’s destination. Due to prohibitively high cost, long lead times, and limited reset capability, testing of mechanisms that require HDRMs is often difficult. This project explored the possibility of designing HDRM-analogue devices that would replicate the function of flight HDRMs during ground-based testing for a fraction of the cost of a flight HDRM. These devices were designed with the requirements of the Spin Eject Mechanism to be used on the Mars Sample Return (MSR) Capture, Containment, and Return System (CCRS) in mind. A trade study was conducted to determine the optimal internal mechanism design of the device, comparing several mechanisms from existing HDRMs to several simpler, more novel mechanisms. CAD software was used to create a preliminary design of the device utilizing a mix of commercial off-the-shelf parts and custom-manufactured parts. Several straightforward analyses were conducted to determine the most effective models for the off-the-shelf parts. A prototype largely composed of 3D-printed components was also created to proof the design concept. Although this HDRM simulator was designed for a particular mechanism for the CCRS mission, its general design is useful for ground testing of a variety of mechanisms requiring similar HDRM simulators.

Kian Vilhauer↗
NASA NTRSDate not supplied

TECHEDSAT-7 and 10: The Little Spacecraft That Could

The NOW (Nanosatellite Orbital Workshop) of NASA Ames Research Center (ARC) has two cubesats in orbit at this time: 6 U TechEdSat-10 (T-10) and the 3U TechEdSat-7 (T-7). T10 was jettisoned from the ISS via the NANORACKS system 7/13/2020, and T-7 was launched via Virgin Orbit 1/17/2021. Both were built by the Nano-satellite Orbital Workshop (NOW) at NASA ARC, and designed and fabricated by interns and students in collaboration with educational institutions. Prototyping novel technologies for non-powered re-entry and communications from orbit are primary research interests, however all subsystems including power generation and distribution, subsystem control, navigation, positioning, heat management etc. extend current technologies. Use of distributed processors using open software platforms and standards other based technologies and software is integral to all segments of spacecraft design. Here, we will present an overview of the spacecraft, experiments, and accomplishments – as well as the next three flight experiments. Some of these experiments include: The exo-brake re-entry system is being developed to enable sample return and end of life disposal; Internal communications for sensors, inter-subsystem and experiments uses both a Zigbee based PAN and internal Wi-Fi for high-speed inter-device communications; The Iridium small message LEO system (Short Burst Data) is used to both command the spacecraft and send data to the ground; Experimental use of the Global-Star system for L-band system comparison and back-up; Collaborative NOAA an experiment to communicate from LEO to the GOES geostationary satellite using the DCS (Data Collection System) with on-board Doppler correction; Mars and Lunar experimental communication systems for future cis-lunar and interplanetary nano-satellites; First demonstration of the NASA Near Earth Network systems with nano-satellites at NASA/Wallops Island; Solar array design and implementation for unique future flexible structures; Power distribution using Tardigrade rad-hard processor omni-board (designed by the team); Distributed processors with internal Wi-Fi connectivity; and Initial experiments with AI/Machine Learning.

M Murbach↗
NASA NTRSDate not supplied

Adapting Waste Processing for Space Applications

It has been estimated that on a 1-year mission, a four-astronaut crew will produce approximately 2,600 kg of waste materials. The current International Space Station practice for waste management is a stow and jettison model in which the trash is simply ejected. The immediate challenge waste poses for long duration space flight is that it represents unproductive mass. Longer term, waste accumulation on planetary surfaces will also pose challenges. A waste management/disposal solution is greatly needed. Simultaneously, significant research and development efforts are being made to enable in-situ resource extraction and recovery for lunar and Mars surface operations. A waste management solution could free up volume, reduce mass and thereby propellant needs, as well as contribute to resource recovery for spacecraft, and eventually, surface operations. The adaptation of many chemical engineering unit operations to the microgravity environment is critical to achieve this goal. An ideal spacecraft waste treatment system would convert waste into useful gases. It should be largely self-sustaining in that it should have the ability to recycle commodities to avoid imposing mass penalties associated with transporting feedstock on the spacecraft at launch. At NASA KSC, a model of what such a system would look like is being developed. In addition, the team has recently completed a suborbital flight campaign with a combustion reactor to demonstrate rudimentary conversion in a microgravity environment and identify challenges for future design. This presentation will discuss what a full waste treatment system could look like, point out challenges relating to various unit operations involved in such a system, and highlight recent progress in space waste management research and development.

Waste Processing↗
NASA NTRS2021

OSIRIS-REx Extended Mission Trajectory Design & Target Search

After jettisoning its Sample Return Capsule (SRC) containing regolith samples from the near-Earth asteroid (101955) Bennu to Earth in September 2023, the Origins, Spectral Interpretation, Resource Identification, and Security–Regolith Explorer (OSIRIS-REx) spacecraft will perform a divert maneuver and safely fly by Earth at an altitude of 250 km. SRC return and the divert maneuver officially mark the completion of the spacecraft’s primary mission; however, it will continue on in heliocentric orbit with a nearly fully-functional instrument suite and enough propellant for nearly 600 m/s Delta-V. The post-Earth flyby trajectory fortuitously enables an exciting extended mission opportunity: rendezvous with the near-Earth asteroid (99942)Apophis immediately following its historic Earth close approach in April 2029. In this paper, we detail the discovery, optimization, and analysis of the Apophis rendezvous trajectory for an extended OSIRIS-REx mission. We also present the technical approach for an alternate target search and corresponding results, assessing the alternate trajectories compared to the baseline Apophis rendezvous from a trajectory design standpoint.

Brian Sutter↗
NASA NTRSDate not supplied

The Planetary Protection Strategy of the Earth Return Orbiter–Capture, Containment & Return System in the Context of the Mars Sample Return Campaign

The Mars Sample Return Campaign aims at bringing back to Earth the rock and atmospheric samples that the rover Perseverance has started to collect on the surface of Mars with the goal of analyzing them in a facility built specifically for this purpose to answer questions about the habitability of Mars. The Campaign consists of several missions, including the Earth Return Orbiter–Capture, Containment & Return System (ERO-CCRS), which will capture the samples previously put in Martian orbit, contain them in redundant containers to ensure that no unsterilized particles are released, and return them to Earth through a parachute-less entry vehicle. Both NASA and ESA policies address the United Nations’ Outer Space Treaty by addressing potential harm from material returned from solar system bodies beyond the Earth-Moon system. In the conduct of Mars Sample Return, the two agencies have agreed to apply approaches consistent with their own standards to campaign elements each provides. This work presents the overall strategy for both forward and backward planetary protection for the ERO-CCRS mission. Specifically, for forward planetary protection, CCRS is not required to meet specific bioburden requirements as a Category III mission provided the ERO (1) meets orbital lifetime requirements during orbiter operations and (2) any elements jettisoned at Mars meet orbital lifetime requirements. CCRS is required to be built in ISO-8 or better cleanrooms and, by agreement with ERO, be compatible with direct bioburden verification methods. For backward planetary protection, the overall approach includes building robust, highly reliable systems to prevent inadvertent release of unsterilized Mars material through redundant containment vessels and particle transport analyses. Ongoing work to define verification approaches and quantify containment assurance levels for specific sample return systems will also be discussed, along with how those data will inform launch approval for ERO-CCRS.

Giuseppe Cataldo↗
NASA NTRS2021

Aerocapture Trajectories for Earth Orbit Technology Demonstration and Orbiter Science Missions at Venus, Earth, Mars, and Neptune

The use of aerocapture to provide the delta-V needed to capture a spacecraft into orbit can provide significant fuel savings compared to a propulsive orbit insertion. The aerocapture guidance method described in this paper uses drag modulation, which deploys a drag skirt in the atmosphere until the amount of delta-V needed to capture into the desired orbit is obtained, at which time the drag skirt is separated from the spacecraft. By modulating the time of drag skirt jettison, the vehicle can target a specific orbit apoapsis in the presence of uncertainties such as entry targeting errors and unknown atmospheric conditions.

Jadusingh, Matt↗