Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Instability control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Multi-harmonic Rutherford island theory

Rutherford island theory, which governs the nonlinear evolution of tearing modes in tokamak plasmas, is generalized to take into account situations in which the conventional one-harmonic approximation is not valid. The analysis incorporates non-inductive currents driven by radio frequency (RF) electromagnetic waves injected into the plasma. A multi-harmonic tearing mode dispersion relation is derived that takes the form of a nonlinear inhomogeneous matrix eigenvalue problem. The dispersion relation is solved in the so-called two-harmonic approximation, in which only the principal Fourier harmonic of the perturbed magnetic flux and its first overtone are included in the calculation. In the absence of RF current drive, the nonlinear behavior of a tearing mode predicted in the two-harmonic approximation does not differ substantially from that predicted in the one-harmonic approximation. On the other hand, RF current drive that is sufficiently localized in the vicinity of the O-points of the mode's magnetic island chain is capable of triggering bifurcations of the O-points (which is impossible in the one-harmonic approximation). However, the current drive is incapable of triggering bifurcations of the island X-points. This finding is significant because Bardóczi and Evans recently observed bifurcations of magnetic island chain O-points in the presence of RF current drive in the DIII-D tokamak but did not observe bifurcations of the X-points. Finally, the changes in the topology of the magnetic island flux-surfaces induced by RF current drive are found to facilitate the stabilization of the tearing mode.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Deep Sigma Point Processes-Assisted Chance-Constrained Power System Transient Stability Preventive Control

Here this paper proposes a deep sigma point processes (DSPP)-assisted chance-constrained power system transient stability preventive control method to deal with uncertain renewable energy and loads-induced stability risk. The traditional transient stability-constrained preventive control is reformulated as a chance-constrained optimization problem. To deal with the computational bottleneck of the time-domain simulation-based probabilistic transient stability assessment, the DSPP is developed. DSPP is a parametric Bayesian approach that allows us to predict system transient stability with high computational efficiency while accurately quantifying the confidence intervals of the predictions that can be used to inform system instability risk. To this end, with a given preset confidence probability, we embed DSPP into the primal dual interior point method to help solve the chance-constrained preventive control problem, where the corresponding Jacobian and Hessian matrices are derived. Comparison results with other existing methods show that the proposed method can significantly speed up preventive control while maintaining high accuracy and convergence

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2021

Impact of DER Communication Delay in AGC: Cyber-Physical Dynamic Co-Simulation: Preprint

Distributed energy resource (DER) frequency regulations are promising technologies for future grid operation. Unlike conventional generators, DERs might require open communication networks to exchange signals with control centers, possibly through DER aggregators; therefore, the impacts of the communication variations including the latency on the system frequency stability need to be investigated. This paper develops a cyber-physical dynamic simulation (CPDS) model based on the Hierarchical Engine for Large-Scale Co-Simulation (HELICS) to evaluate the impact of the communication variations, such as delays in DER frequency regulations. The feasible delay range can be obtained under different AGC parameter settings. The results show that the risk of instability generally increases with the communication delay and that the difference of AGC provided from DER and conventional generation units should be recognized when designing frequency regulation controllers.

61 RADIATION PROTECTION AND DOSIMETRY↗
DOE OSTI2020

Kinetic effects of self-organization in low-temperature magnetized plasmas (Final Report for DE-SC0019045: 9/1/2018-8/31/2019)

The research goal of this Early Career Research Program project is to advance the science of low temperature magnetized plasmas using first-principles kinetic, e.g., solving the Boltzmann equation, models. A better understanding of the plasma transport properties, such as electrical resistivity and thermal conductivity must be obtained to better control and design magnetized plasma sources. A key physical phenomenon in low-temperature magnetized plasmas is the self-organization of plasma flows, e.g., coherent plasma structures and transition between different discharge modes. Understanding the physics of coherent plasma structures has been identified as one of the four important frontier topics in a recent workshop by the Office of Fusion Energy Science. These self-emerging plasma patterns results from the nonlinear coupling between plasma constituents (ions, electrons, and neutral atoms), electromagnetic fields, and materials. The physics of low-temperature magnetized plasmas is particularly complex because (i) the collisionless instabilities affect collisional phenomena (ionization, transport, etc.) and vice versa and (ii) the presence of materials (sheath, electron injection, etc.) influences the bulk plasma properties in low-temperature plasma (LTP) devices. Computational models of these plasma flows remain challenging because the plasma density can vary several orders of magnitudes, a wide range of temporal and spatial scales must be resolved, the phenomena are inherently three-dimensional, and various physical processes, such as wall interaction, instabilities, inelastic collisions, etc., must be simultaneously and self-consistently taken into account. Understanding the fundamental transport mechanisms in cross-field configurations enables additional controllability of plasma properties and electron energy distribution functions (EEDFs).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Inertial dynamics of an interface with interfacial mass flux: Stability and flow fields’ structure, inertial stabilization mechanism, degeneracy of Landau’s solution, effect of energy fluctuations, and chemistry-induced instabilities

This work focuses on the long-standing problem of inertial dynamics of an interface with interfacial mass flux and reports new mechanisms for the interface stabilization and destabilization. The interface is a phase boundary separating fluids of different densities and having interfacial mass flux. To analyze the interface dynamics from a far field, we develop and apply the general matrix method to rigorously solve the boundary value problem involving the governing equations in the fluid bulk and the boundary conditions at the interface and at the outside boundaries of the domain. We find the fundamental solutions for the linearized system of equations and analyze the interplay of interface stability with flow fields’ structure by directly linking rigorous mathematical attributes to physical observables. We find that the interface is stable when the dynamics conserves the fluxes of mass, momentum, and energy; the stabilization is due to an inertial mechanism causing small oscillations of the interface velocity. In the classic Landau’s dynamics, the postulate of perfect constancy of the interface velocity leads to the development of Landau–Darrieus instability. This destabilization is also linked to the imbalance of the perturbed energy at the interface. The classic Landau’s solution is found to have degeneracy; lifting of the degeneracy may lead to singularity and self-similar dynamics. Our results compare well with traditional theories of combustion and propose new experiments to study the dynamics of the interface and the flow fields in combustible systems. We further conduct reactive molecular dynamics simulations to elucidate the complexity of chemical processes, to study the destabilizing effect of energy fluctuations on the interface stability, and to illustrate the chemistry-induced instabilities. In summary, we identify the extreme sensitivity of the interface dynamics to the interfacial boundary conditions, including the formal properties of fundamental solutions and the qualitative and quantitative properties of the flow fields. This provides new opportunities for studies, diagnostics, and control of multiphase flows in a broad range of processes in nature and technology.

42 ENGINEERING↗
DOE OSTI2024

Benign termination of runaway electron beams on ASDEX Upgrade and TCV

Abstract This paper discusses the development of a benign termination scenario for runaway electron (RE) beams on ASDEX Upgrade and TCV. A systematic study revealed that a low electron density (n e ) companion plasma was required to achieve a large MHD instability, which expelled the confined REs over a large wetted area and allowed for the conversion of magnetic energy to radiation. Control of the companion plasma n e was achieved via neutral pressure regulation and was agnostic to material injection method. The neutral pressure required for recombination was found to be dependent on impurity species, quantity and RE current. On TCV,n e increased at neutral pressures above 1 Pa, indicating that higher collisionality between the REs and neutrals may lead to an upper pressure limit. The conversion of magnetic energy to radiated energy was measured on both machines and a decrease in efficiency was observed at high neutral pressure on TCV. The benign termination technique was able to prevent any significant increase in maximum heat flux on AUG from 200 to 600 kA of RE current, highlighting the ability of this approach to handle fully formed RE beams.

Physics↗
DOE OSTI2021

Empirical Evaluation of GPS Clock Accuracy for Isochronous Droop-based Inverters

Grid-forming inverters rely upon an internal reference to regulate the grid 's voltage and frequency. Without a reliable reference, issues such as loss of synchronism, frequency instability, and unequal power sharing can occur. One proposed internal phase reference for grid-forming inverters is generated by the controller's clock, but this is affected by nonidealities in the crystal oscillator leading to time drift in the phase reference. To improve the controller's clock accuracy, the Global Positioning System (GPS) can be used to calibrate the internal clock. Previously, GPS-based clock calibration was explored theoretically and various methods were developed for mitigating frequency/phase drift at the power system level. This paper experimentally validates the direct performance of GPS time-calibration at the controller level and justifies its use in maintaining an accurate phase reference for droop-based grid-forming inverters.

clock drift↗
DOE OSTI2021

EGR Dilution and Fuel Property Effects on High-Efficiency Spark-Ignition Flames

Modern spark ignition internal combustion engines rely on fast combustion rates and high dilution to achieve high brake thermal efficiencies. To accomplish this, new engine designs have moved towards increased tumble ratios and stroke-to-bore ratios. Increased tumble ratios correlate positively with increases in turbulent kinetic energy and improved fuel and residual gas mixing, all of which favor faster and more efficient combustion. Longer stroke-to-bore ratios allow higher geometric compression ratios and use of late intake valve closing to control peak compression pressures and temperatures. The addition of dilution to improve efficiency is limited by the resulting increase in combustion instabilities manifested by cycle-to-cycle variability. A number of effects - preferential diffusion, turbulence-combustion interactions, stochastic flow patterns, laminar-turbulent flame kernel transitions, and relative length and velocity scales between flame and turbulence - are believed to be responsible for the increase in cycle-to-cycle variations, where their contributions are likely interlinked. Several studies have shown the influence of stochastic flow characteristics on the nature of combustion instabilities, such as velocity patterns on flame kernel formation and cycle-to-cycle variations in residual gas. However, few have focused on the specific effects of fuel properties. The objective of this work is to contrast the effects of dilution on propane stoichiometric combustion against gasoline. Dilution tolerance experiments were conducted in a purpose-built high stroke-to-bore ratio single cylinder engine with both gasoline and LPG. Three-dimensional full cycle computational fluid dynamics (CFD) simulations employing a level-set combustion approach and Reynolds averaged Navier-Stokes (RANS) turbulence modeling was used to qualitatively assess the changes in length and velocity scales for turbulence and the flame. The experimental results showed that LPG can tolerate higher exhaust gas recirculation (EGR) dilution under a variety of conditions. Analysis of CFD simulations showed that propane flames are likely less sensitive to influences from the flow field due to less thickening of the flame and higher effective flame speeds.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Empirical Evaluation of GPS Clock Accuracy for Isochronous Droop-Based Inverters: Preprint

Grid-forming inverters rely upon an internal reference to regulate the grid’s voltage and frequency. Without a reliable reference, issues such as loss of synchronism, frequency instability, and unequal power sharing can occur. One proposed internal phase reference for grid-forming inverters is generated by the controller’s clock, but this is affected by nonidealities in the crystal oscillator leading to time drift in the phase reference. To improve the controller’s clock accuracy, the Global Positioning System (GPS) can be used to calibrate the internal clock. Previously, GPS-based clock calibration was explored theoretically and various methods were developed for mitigating frequency/phase drift at the power system level. This paper experimentally validates the direct performance of GPS time-calibration at the controller level and justifies its use in maintaining an accurate phase reference for droop-based grid-forming inverters.

clock drift↗
DOE OSTI2025

Conflict Detection in Open RAN with Recurrent Neural Networks Using Geometric Manifolds

Allowing third-party applications on Radio Access Network (RAN) Intelligent Controllers (RICs) within the OpenRAN (O-RAN) framework introduces conflicting interactions that are often difficult to detect in advance. These conflicts, occurring between third-party applications in the Near RealTime RIC (Near-RT RIC), known as xApps, can lead to performance degradation and instability in O-RAN if not identified early. Existing conflict detection and mitigation solutions in the literature assume that the conflicts are known beforehand, which is not always accurate due to the complex and often hidden relationships between control parameters and Key Performance Indicators (KPIs). In this paper, we propose a novel Recurrent Neural Network (RNN) to detect both known and unknown conflicts in O-RAN xApps as specified in the O-RAN standards. We model the xApps, control parameters, and KPIs with nodes and edges to create graph structures and use the hidden nonEuclidean geometric properties of the Riemannian manifold to train the RNN model. The performance of this proposed model is validated using evaluation metrics and compared with benchmarks. Results demonstrate that the proposed RNN model, leveraging Riemannian geometric properties, can achieve 100% of the F1-score provided by an optimal solution in just 20 iterations.

5G↗
DOE OSTI2025

Conflict Detection in Open RAN with Recurrent Neural Networks Using Geometric Manifolds

Allowing third-party applications on Radio Access Network (RAN) Intelligent Controllers (RICs) within the OpenRAN (O-RAN) framework introduces conflicting interactions that are often difficult to detect in advance. These conflicts, occurring between third-party applications in the Near RealTime RIC (Near-RT RIC), known as xApps, can lead to performance degradation and instability in O-RAN if not identified early. Existing conflict detection and mitigation solutions in the literature assume that the conflicts are known beforehand, which is not always accurate due to the complex and often hidden relationships between control parameters and Key Performance Indicators (KPIs). In this paper, we propose a novel Recurrent Neural Network (RNN) to detect both known and unknown conflicts in O-RAN xApps as specified in the O-RAN standards. We model the xApps, control parameters, and KPIs with nodes and edges to create graph structures and use the hidden nonEuclidean geometric properties of the Riemannian manifold to train the RNN model. The performance of this proposed model is validated using evaluation metrics and compared with benchmarks. Results demonstrate that the proposed RNN model, leveraging Riemannian geometric properties, can achieve 100% of the F1-score provided by an optimal solution in just 20 iterations.

5G↗
DOE OSTI2026

Chaos as the cause of randomness in tearing mode onset times in DIII-D ITER baseline scenario plasmas

The first evidence of widespread chaotic plasma dynamics relevant to the onset of disruptive tearing modes is found in DIII-D tokamak discharges. This evidence is obtained by calculating positive maximal Lyapunov exponents from Mirnov signals using the Rosenstein algorithm, implying the chaotic growth and/or rotation of magnetohydrodynamic modes in DIII-D [Luxon, Nucl. Fusion 42, 614 (2002)] plasmas. Such chaotic dynamics offer an explanation for the random tearing mode onset times previously observed in ITER baseline scenario discharges. Further, the Lyapunov timescales associated with this chaos could inhibit reliable prediction of tearing mode onset beyond the angular momentum confinement timescale; this constraint should inform the design of plasma control systems on ITER.

Chaotic dynamics↗
DOE OSTI2021

Partially averaged Navier-Stokes closure modeling for variable-density turbulent flow

We report this work extends the framework of the partially averaged Navier-Stokes (PANS) equations to variable-density flow, i.e., multimaterial and/or compressible mixing problems with density variations and production of turbulence kinetic energy by both shear and buoyancy mechanisms. The proposed methodology is utilized to derive the PANS BHR-LEVM closure. This includes a priori testing to analyze and develop guidelines toward the efficient selection of the parameters controlling the physical resolution and, consequently, the range of resolved scales of PANS. Two archetypal test-cases involving transient turbulence, hydrodynamic instabilities, and coherent structures are used to illustrate the accuracy and potential of the method: the Taylor-Green vortex at Reynolds number Re = 3000, and the Rayleigh-Taylor flow at Atwood number 0.5 and (Re) max ≈ 500. These representative problems, for which turbulence is generated by shear and buoyancy processes, constitute the initial validation space of the new model, and their results are comprehensively discussed in two subsequent studies. The computations indicate that PANS can accurately predict the selected flow problems, resolving only a fraction of the scales of large-eddy simulation and direct numerical simulation strategies. The results also reiterate that the physical resolution of the PANS model must guarantee that the key instabilities and coherent structures of the flow are resolved. The remaining scales can be modeled through an adequate turbulence scale-dependent closure.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

Processability and Material Behavior of NiTi Shape Memory Alloys Using Wire Laser-Directed Energy Deposition (WL-DED)

Utilizing additive manufacturing (AM) techniques with shape memory alloys (SMAs) like NiTi shows great promise for fabricating highly flexible and functionally superior 3D metallic structures. Compared to methods relying on powder feedstocks, wire-based additive manufacturing processes provide a viable alternative, addressing challenges such as chemical composition instability, material availability, higher feedstock costs, and limitations on part size while simplifying process development. This study presented a novel approach by thoroughly assessing the printability of Ni-rich Ni55.94Ti (Wt. %) SMA using the wire laser-directed energy deposition (WL-DED) technique, addressing the existing knowledge gap regarding the laser wire-feed metal additive manufacturing of NiTi alloys. For the first time, the impact of processing parameters—specifically laser power (400–1000 W) and transverse speed (300–900 mm/min)—on single-track fabrication using NiTi wires in the WL-DED process was examined. An optimal range of process parameters was determined to achieve high-quality prints with minimal defects, such as wire dripping, stubbing, and overfilling. Building upon these findings, we printed five distinct cubes, demonstrating the feasibility of producing nearly porosity-free specimens. Notably, this study investigated the effect of energy density on the printed part density, impurity pick-up, transformation temperature, and hardness of the manufactured NiTi cubes. The results from the cube study demonstrated that varying energy densities (46.66–70 J/mm3) significantly affected the quality of the deposits. Lower to intermediate energy densities achieved high relative densities (>99%) and favorable phase transformation temperatures. In contrast, higher energy densities led to instability in melt pool shape, increased porosity, and discrepancies in phase transformation temperatures. These findings highlighted the critical role of precise parameter control in achieving functional NiTi parts and offer valuable insights for advancing AM techniques in fabricating larger high-quality NiTi components. Additionally, our research highlighted important considerations for civil engineering applications, particularly in the development of seismic dampers for energy dissipation in structures, offering a promising solution for enhancing structural performance and energy management in critical infrastructure.

Dabbaghi, Hediyeh↗
DOE OSTI2022

Using a Grid-Forming Inverter to Stabilize a Low-Inertia Power System - Maui Hawaiian Island

As power systems around the world integrate greater amounts of wind and solar photovoltaic power, periods of very high instantaneous power shares of inverters, the primary interfacing technology for these generation sources, are complicating system stability and control. The contemporary, primary mode of inverter operation, grid-following, which explicitly assumes the presence of a local, stable voltage waveform, yields operational inadequacy at high instantaneous power shares potentially leading to instability due to the low-inertia conditions, as well as the correlated reduced voltage forming capacity on the respective system. Parallel connected grid-forming inverters, which directly regulate the local voltage, are a solution that is expected to bolster system stability and mitigate the shortcomings of the grid-following technology. In this paper, grid-following and two types of grid-forming inverter control, the traditional linear droop and the recently introduced nonlinear exponential droop (Droop-e), are simulated on a low-inertia, H = 0.48s, high inverter-based resource scenario, 97%, with a validated electromagentic transient domain model of the Hawaiian island of Maui power system. The benefit of a single grid-forming device over its grid-following counterpart is significant, both in terms frequency deviation and voltage stability. Further, the superiority of the Droop-e and the associated secondary power sharing control over both grid-following and linear droop grid-forming technologies is displayed, with improved nadir and rate of change of frequency over the linear droop control.

droop control↗
DOE OSTI2023

Ferroelectricity in hafnia controlled via surface electrochemical state

Ferroelectricity in binary oxides including hafnia and zirconia has riveted the attention of the scientific community due to the highly unconventional physical mechanisms and the potential for the integration of these materials into semiconductor workflows. Over the last decade, it has been argued that behaviours such as wake-up phenomena and an extreme sensitivity to electrode and processing conditions suggest that ferroelectricity in these materials is strongly influenced by other factors, including electrochemical boundary conditions and strain. Here we argue that the properties of these materials emerge due to the interplay between the bulk competition between ferroelectric and structural instabilities, similar to that in classical antiferroelectrics, coupled with non-local screening mediated by the finite density of states at surfaces and internal interfaces. Via the decoupling of electrochemical and electrostatic controls, realized via environmental and ultra-high vacuum piezoresponse force microscopy, we show that these materials demonstrate a rich spectrum of ferroic behaviours including partial-pressure-induced and temperature-induced transitions between ferroelectric and antiferroelectric behaviours. In conclusion, these behaviours are consistent with an antiferroionic model and suggest strategies for hafnia-based device optimization.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Grid-Interactive Electric Vehicle and Building Coordination Using Coupled Distributed Control: Preprint

As an increasing number of controllable devices are introduced onto the grid, they can individually provide ancillary services in support of grid stability. However, the goals of each device differ due to their type and individual objectives, causing instances where they may conflict. To reduce the chances of these devices contributing to grid instability, these devices must effectively communicate in a cooperative manner to both meet their own needs while providing services to the grid. Previous work demonstrates that the NALD (Network Lasso-ADMM - Limited Communication - DMPC) algorithm allows coordination between two subsystems that use different control algorithms (building and charging stations) to provide services to the grid and individually optimize their performance in a specific scenario. The ideal NALD algorithm should be generalized to allow plug-and-play capabilities across devices of differing characteristics. This paper takes a step toward generalizability by updating the electric vehicle charging objective and re-defining the communication scheme compared to prior work to generalize the coordination and, as a result, improve the performance of the NALD algorithm.

ADVANCED PROPULSION SYSTEMS,ENERGY CONSERVATION, C↗
DOE OSTI2021

Constraining computational modeling of indirect drive double shell capsule implosions using experiments

Double shell capsule implosions are an alternative approach to achieving alpha heating on the National Ignition Facility. Current machining techniques construct the outer shell as two hemispheres that are glued together, and the deuterium and tritium (DT) liquid inside the inner shell will be injected by a fill tube. These features introduce asymmetries and jetting that may disrupt the confinement of the DT fuel if not carefully controlled. Simulations indicate that in order to achieve high yields in the laboratory, these features as well as susceptibility to the Rayleigh–Taylor instability (RTI) must be mitigated. Furthermore, due to uncertainties in computational models and the expense of using the best physics models at adequate resolution in three dimensions, our computational modeling must be constrained by experiments. We report on the results of recent hydrogrowth radiography and dual-axis keyhole experiments with double shell targets that have been used to evaluate our modeling of the outer shell joint as well as the impacts of high-energy x-ray preheat that strongly impacts RTI growth. Our simulations show good agreement with the experimental data and inform several important modeling choices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗