Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Impact loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS2024

Modeling Dynamic Crush Behavior of Carbon Fiber Reinforced Polymer Composite Structures Using MAT213

Modeling crushing of carbon fiber reinforced polymer (CFRP) composites is challenging, and current simulation methodologies involve tuning of non-physical parameters. MAT213, a next-generation material model, has advanced functionality to better simulate dynamic impact loading. The objective of the present investigation is to evaluate the potential for using MAT213 to simulate dynamic crushing of CFRPs. Two sets of simulations were performed: one for calibration based on a set of coupon-level experiments and another for prediction of the response of structural elements. Simulations involving dynamic crushing of flat specimens were iteratively run to calibrate model parameters. The calibration demonstrated that MAT213 could produce a simulated force-displacement response within experimental scatter. The simulated failure morphology was also comparable to the experiments. After successful calibration, predictive simulations of dynamic crushing of C-channel shaped specimens were completed using a simulated crash sled test rig and two pairs of impactor mass/velocity conditions. The simulated force-displacement curve in the crash sled simulations for the lower-velocity condition fell within the experimental scatter, but the stable crush force was underpredicted by 27% in the higher-velocity simulations. Better correlation in the lower-velocity test condition likely results from the calibration condition being a similar velocity to the lower-velocity crash sled condition.

Dynamic Crush↗
NASA NTRS1976

SRM attrition rate study of the aft motor case segments due to water impact cavity collapse loading

The attrition assessment of the aft segments of Solid Rocket Motor due to water impact requires the establishment of a correlation between loading occurrences and structural capability. Each discrete load case, as identified by the water impact velocities and angle, varies longitudinally and radially in magnitude and distribution of the external pressure. The distributions are further required to be shifted forward or aft one-fourth the vehicle diameter to assure minimization of the effect of test instrumentation location for the load determinations. The asymmetrical load distributions result in large geometric nonlinearities in structural response. The critical structural response is progressive buckling of the case. Discrete stiffeners have been added to these aft segments to aid in gaining maximum structural capability for minimum weight addition for resisting these loads. This report presents the development of the attrition assessment of the aft segments and includes the rationale for eliminating all assessable conservatisms from this assessment.

Crockett, C. D.↗
NASA NTRS1989

On modelling the residual strength of impact damaged, compression loaded laminates

A methodology is presented to predict the residual compression strength of impact damaged composite laminates by considering the competing failure modes of local delamination buckling and compression failure. The minimum delamination buckling load and the location of the first local region to buckle are determined by a Rayleigh-Ritz analysis. The Rayleigh-Ritz analysis is formulated to account for the multiple delamination locations, Poisson's ratio mismatch between sublaminates and possible bending-stretching coupling behavior of the delaminated regions. The compression failure load is determined by a modified maximum strain criterion applied in the delaminated region. The minimum delamination buckling and compression failure loads may be compared to the global buckling load to predict initial failure. For non-catastrophic failures, failure sequences are predicted in an iterative manner. Analytical predictions for sequential failure modes and loads are shown to correlate well with experimental results. A comparative evaluation of various delamination buckling models and their accuracy in predicting experimental results is also presented.

Davidson, B. D.↗
NASA NTRS1992

Study of compression-loaded and impact-damaged structurally efficient graphite-thermoplastic trapezoidal-corrugation sandwich and semisandwich panels

The structural efficiency of compression-loaded trapezoidal-corrugation sandwich and semisandwich composite panels is studied to determine their weight savings potential. Sandwich panels with two identical face sheets and a trapezoidal corrugated core between them and semisandwich panels with a corrugation attached to a single skin are considered. An optimization code is used to find the minimum weight designs for critical compressive load levels ranging from 3000 to 24,000 lb/in. Graphite-thermoplastic panels based on the optimal minimum weight designs were fabricated and tested. A finite element analysis of several test specimens was also conducted. The results of the optimization study, the finite element analysis, and the experiments are presented. The results of testing impact damage panels are also discussed.

Jegley, Dawn C.↗
NASA NTRS1976

A mathematical model of an active control landing gear for load control during impact and roll-out

A mathematical model of an active control landing gear (ACOLAG) was developed and programmed for operation on a digital computer. The mathematical model includes theoretical subsonic aerodynamics; first-mode wing bending and torsional characteristics; oleo-pneumatic shock strut with fit and binding friction; closed-loop, series-hydraulic control; empirical tire force-deflection characteristics; antiskid braking; and sinusoidal or random runway roughness. The mathematical model was used to compute the loads and motions for a simulated vertical drop test and a simulated landing impact of a conventional (passive) main landing gear designed for a 2268-kg (5000-lbm) class airplane. Computations were also made for a simply modified version of the passive gear including a series-hydraulic active control system. Comparison of computed results for the passive gear with experimental data shows that the active control landing gear analysis is valid for predicting the loads and motions of an airplane during a symmetrical landing. Computed results for the series-hydraulic active control in conjunction with the simply modified passive gear show that 20- to 30-percent reductions in wing force, relative to those occurring with the modified passive gear, can be obtained during the impact phase of the landing. These reductions in wing force could result in substantial increases in fatigue life of the structure.

Mcgehee, J. R.↗
NASA NTRS1984

SRB/FWC water impact: Flexible body loads test

Two technical areas were examined: evaluation of potential correction methods for spurious case strain outputs from the pressure transducers during the NSWC tests; and assessing procedures for modifying either the excitation function or the response function to account for hydroelastic effects.

Source record↗
NASA NTRS1984

SRB/FWC water impact: Flexible body loads test

The modeling of the cavity collapse pressure loading is discussed. There are excellent high speed color films of the quarter scale model during cavity collapse. In these films, it is possible to see a very clearly defined pressure wave front propagating circumferentially around the vehicle that seems to be associated at least on the lee side with an abrupt rise in pressure at each pressure transducer. By using a motion analyzer and stepping through the films, the location of this wave front is tracted at a number of time intervals for drops 17 through 21. The entry conditions and average wave front velocity are shown. Mathematical formulae aid in the reconstruction of the spatial distribution of the pressure.

Source record↗
NASA NTRS1984

Analyses of quasi-isotropic composite plates under quasi-static point loads simulating low-velocity impact phenomena

In thin composite laminates, the first level of visible damage occurs in the back face and is called back face spalling. A plate-membrane coupling model, and a finite element model to analyze the large deformation behavior of eight-ply quasi-isotropic circular composite plates under impact type point loads are developed. The back face spalling phenomenon in thin composite plates is explained by using the plate-membrane coupling model and the finite element model in conjunction with the fracture mechanics principles. The experimental results verifying these models are presented. Several conclusions concerning the deformation behavior are reached and discussed in detail.

Kelkar, A. D.↗
NASA NTRS1994

Impact of dynamic loads on propulsion integration

Aircraft dynamic loads produced by engine exhaust plumes are examined for a class of military fighter and bomber configurations in model and full scale. The configurations examined are associated with the USAF F-15 and B-1B aircraft, and the US F-18 HARV and ASTOVL programs. The experience gained as a result of these studies is used to formulate a level of understanding concerning this phenomena that could be useful at the preliminary stage of propulsion/airframe design.

Seiner, J. M.↗
NASA NTRS2019

How Does Water Delivery System Design Impact the Microbial Load of Salad Crops?

In a microgravity setting, such as the environment aboard the International Space Station (ISS), an ideal plant water delivery system is one that can grow edible crops with minimal resource consumption and minimal risk to crew members. There are also concerns associated with the ability to control fluid escape and biofilm formation resulting in potential dangers to systems, crops, or crewmembers. To identify an appropriate system, candidate systems were assembled and operated under simulated ISS environmental conditions (T,CO2,and RH) with red romaine lettuce (Lactuca sativa cultivar 'Outredgeous') as a model crop. Fluid reservoirs and randomly selected planting sites were sampled every seven days until maturity at which point edible plant biomass and root samples were also taken. Heterotrophic bacteria and fungi growth patterns throughout each planting cycle were determined by plate counts on appropriate agar media. The candidate systems were compared to a classic hydroponics system as a control and harvested crops were compared to controls as well as Veggie-grown and market produce. Plants harvested from candidate systems yielded lower average heterotrophic bacteria and fungi per gram of plant mass levels when compared to market and Veggie samples as well as those from the control system. Additional studies to evaluate the system sanitation regimen as well as testing additional crops should be considered to aid in the selection of an ideal system.

Curry, Aaron B.↗
NASA NTRS1986

Effects of partial interlaminar bonding on impact resistance and loaded-hole behavior of graphite/epoxy quasi-isotropic laminates

A partial-bonding interlaminar toughening concept was evaluated for resistance to impact and for behavior of a loaded hole. Perforated Mylar sheets were interleaved between all 24 plies of a graphite/epoxy quasi-isotropic lay-up. Specimens were impacted by aluminum spheres while under tensile or compressive loads. Impact-failure thresholds and residual strengths were obtained. Loaded-hole specimens were tested in three configurations that were critical in bearing, shear, or tension. Partial bonding reduced the tensile and compressive strengths of undamaged specimens by about one-third. For impact, partial bonding did not change the threshold for impact failure under tensile preload. However, under compressive preload, partial bonding caused serious degradation of impact resistance. Partial bonding reduced the maximum load-carrying capacity of all three types of loaded-hole specimens. Overall, partial bonding degraded both impact resistance and bearing strength of holes.

Illg, W.↗
NASA NTRS1990

Survivability characteristics of composite compression structure

Test and evaluation was performed to determine the compression residual capability of graphite reinforced composite panels following perforation by high-velocity fragments representative of combat threats. Assessments were made of the size of the ballistic damage, the effect of applied compression load at impact, damage growth during cyclic loading and residual static strength. Several fiber/matrix systems were investigated including high-strain fibers, tough epoxies, and APC-2 thermoplastic. Additionally, several laminate configurations were evaluated including hard and soft laminates and the incorporation of buffer strips and stitching for improved damage resistance of tolerance. Both panels (12 x 20-inches) and full scale box-beam components were tested to assure scalability of results. The evaluation generally showed small differences in the responses of the material systems tested. The soft laminate configurations with concentrated reinforcement exhibited the highest residual strength. Ballistic damage did not grow or increase in severity as a result of cyclic loading, and the effects of applied load at impact were not significant under the conditions tested.

Avery, John G.↗
NASA NTRS1995

The effects of tensile preloads on the impact response of carbon/epoxy laminates

The effects of tensile preloads on the tension-after-impact (TAI) strength of composite laminates of IM7/8551-7 were examined. A failure threshold curve was first determined so the most informative values for preload/impact energy combinations could be determined. The impact tests were instrumented so maximum load of impact, as well as several other parameters could be measured. The elastic response data indicate that as the tensile preload is increased, the maximum load of impact also increases. The damage data show that at low impact energies, the damage/failure is an 'all-or-nothing' event but at higher impact energies, a region of preload values exists where the coupons could sustain damage, yet not fail catastrophically.

Nettles, Alan↗
NASA NTRS2002

Androgynous, Reconfigurable Closed Loop Feedback Controlled Low Impact Docking System With Load Sensing Electromagnetic Capture Ring

The present invention relates to a fully androgynous, reconfigurable closed loop feedback controlled low impact docking system with load sensing electromagnetic capture ring. The docking system of the present invention preferably comprises two Docking- assemblies, each docking assembly comprising a load sensing ring having an outer face, one of more electromagnets, one or more load cells coupled to said load sensing ring. The docking assembly further comprises a plurality of actuator arms coupled to said load sensing ring and capable of dynamically adjusting the orientation of said load sensing ring and a reconfigurable closed loop control system capable of analyzing signals originating from said plurality of load cells and of outputting real time control for each of the actuators. The docking assembly of the present invention incorporates an active load sensing system to automatically dynamically adjust the load sensing ring during capture instead of requiring significant force to push and realign the ring.

Lewis, James L.↗
NASA NTRS1998

Damage Characteristics and Residual Strength of Composite Sandwich Panels Impacted with and Without Compression Loading

The results of an experimental study of the impact damage characteristics and residual strength of composite sandwich panels impacted with and without a compression loading are presented. Results of impact damage screening tests conducted to identify the impact-energy levels at which damage initiates and at which barely visible impact damage occurs in the impacted facesheet are discussed. Parametric effects studied in these tests include the impactor diameter, dropped-weight versus airgun-launched impactors, and the effect of the location of the impact site with respect to the panel boundaries. Residual strength results of panels tested in compression after impact are presented and compared with results of panels that are subjected to a compressive preload prior to being impacted.

McGowan, David M.↗
NASA NTRS1997

A Study of the Use of Contact Loading to Simulate Low Velocity Impact

Although numerous studies on the impact response of laminated composites have been conducted, there is as yet no agreement within the composites community on what parameter or parameters are adequate for quantifying the severity of an impact event. One of the more interesting approaches that has been proposed uses the maximum contact force during impact to "quantify" the severity of the impact event, provided that the impact velocity is sufficiently low. A significant advantage of this approach, should it prove to be reliable, is that quasi-static contact loading could be used to simulate low velocity impact. In principle, a single specimen, loaded quasi-statically to successively increasing contact loads could be used to map the entire spectrum of damage as a function of maximum contact force. The present study had as its objective assessing whether or not the maximum contact force during impact is a suitable parameter for characterizing an impact. The response of [+/-60/0(sub 4)/+/-60/0(sub 2)](sub s) laminates fabricated from Fiberite T300/934 graphite epoxy and subjected to quasi-static contact loading and to low velocity impact was studied. Three quasi-static contact load levels - 525 lb., 600 lb., and 675 lb. - were selected. Three impact energy levels - 1.14 ft.-lb., 2.0 ft.-lb., and 2.60 ft.-lb. - were chosen in an effort to produce impact events in which the maximum contact forces during the impact events were 525 lb., 600 lb., and 625 lb., respectively. Damage development was documented using dye-penetrant enhanced x-ray radiography. A digital image processing technique was used to obtain quantitative information about the damage zone. Although it was intended that the impact load levels produce maximum contact forces equal to those used in the quasi-static contact experiments, larger contact forces were developed during impact loading. In spite of this, the damage zones developed in impacted specimens were smaller than the damage zones developed in specimens subjected to the corresponding quasi-static contact loading. The impacted specimens may have a greater tendency to develop fiber fracture, but, at present, a quantitative assessment of fiber fracture is not available. In addressing whether or not contact force is an adequate metric for describing the severity of an impact event, the results of this study suggest that it is not. In cases where the quasi-static load level and the maximum contact force during impact were comparable, the quasi-statically loaded specimens consistently developed larger damage zones. It should be noted, however, that using quasi-static damage data to forecast the behavior of impacted material may give conservative estimates of the residual strength of impacted composites.

Highsmith, Alton L.↗
NASA NTRS1946

Waters Loads on the XJL-1 Hull as Obtained in Langley Impact Basin, TED No. NACA 2413.3

An investigation was conducted in the Langley impact basin of the water loads on a half scale model of the XJL-1 hull whose forebody has a vee bottom with exaggerated chine flare. The impact loads, moments, and pressures were determined for a range of landing conditions. A normal full-scale landing speed of 86 miles per hour was represented with effective flight paths ranging from 0.6deg to 11.6deg. Landings were made with both fixed trim and free-to-trim mounting of the float over a trim range of -15deg to 12deg into smooth water and into waves having equivalent full-scale length. of 120 feet and heights ranging from 1 to 4 feet. All data and results presented in this report are given in terms of equivalent full-scale values. Summary tables and illustrative plots are used in presenting the material. The following maximum values of load and pressure are those which are apropos for effective flight paths less than 6.5deg which was the maximum value obtained in tests with the XJL-1 hull model representing full-scale landings with vertical velocity of 4.5 feet per second into 4-foot waves. The maximum local pressure on the flat portion of the bottom is 130 pounds per square inch which was measured on a 2-inch-diameter circular area near the step. The maximum local pressure obtained in the curved area near the chines is 200 pounds per square inch. This pressure was also measured near the step.

Steiner, Margaret F.↗
NASA NTRSDate not supplied

Determining Chlamydomonas reinhardtii resistance to ionizing radiation at a genome-wide scale

Spaceflight is a complex mixture of abiotic stresses that causes a myriad of cellular responses including increased genome-wide mutation load. The impact of spaceflight on mutation load is not well understood for most organisms and is especially critical to characterize for candidate microorganisms that could be part of biological life support systems. Prior research in our laboratory revealed an unexpectedly high level of mutation during spaceflight in the eukaryotic green algae, C. reinhardtii. Based on the spectrum of base changes observed, we concluded that the mutations were generated through a molecular mechanism unique to the spaceflight environment. Spaceflight is a complex set of stresses, and we are using an Earth-based analog to test ionizing radiation as a potential causative variable for the unique mutation spectrum observed in spaceflight. C. reinhardtii was grown exposed to chronic radiation from a Cesium-137 source. Four biological replicate cultures of wild-type cells were grown in gas permeable plastic tissue culture bags in liquid media following the design used on the International Space Station (ISS) during the previous space algae experiment. Radiation levels for this experiment approximate ionizing radiation observed on the moon, in low Earth orbit (LEO), and on Earth. Cells from each replicate were passaged to inoculate the next cycle of growth, then samples were taken from each culture to characterize cell morphology, quantify biomass, and extract DNA. Whole genome sequencing from each culture will be used to identify the frequency and types of mutations in each radiation level. In growth cycles 3 and 4, there was a significant increase in biomass accumulation under lunar radiation level compared to LEO or Earth radiation levels. These results such that ionizing radiation affected growth of C. reinhardtii.

Microbiology↗