SEARCH · Engineering Papers

Results for “Helium cooling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

All sources NASA NTRS DOE OSTI

DOE OSTI2020

Real-time gas cooling of flowing liquid lithium limiter for the EAST

A novel continuously flowing liquid lithium limiter (FLiLi) which employs an in-vessel electro-magnetic pump to drive liquid Li flowing on the surface of limiter has been successfully designed and tested in the experimental advanced superconducting tokamak (EAST) device in 2014. In order to better control the surface temperature, an upgraded design and the real-time gas cooling were performed in 2016. Two kinds of cooling gas, helium (He) and argon (Ar) were tested on the FLiLi system prior to the experiment. It was found that the cooling rates of He and Ar at 2.5 MPa are 34.2 °C/min, 10.2 °C/min or 31.7 °C/kL and 28.1 °C/kL, respectively. The cooling performance of He is more effective than Ar. Experimental results show that the real-time He cooling could effectively contain the FLiLi surface temperature increase and prevent the strong passive evaporation of lithium during plasma discharges. Limiter heat flux up to 0.2 MW/m2 was removed during ohmic discharge with 2.5 MPa He gas. Finally, Because of the upgraded design and real-time gas cooling, the surface of FLiLi was not damaged by heat flux after entire plasma discharge.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS1978

Experimental investigation of contamination prevention techniques to cryogenic surfaces on board orbiting spacecraft

Within the simulation limitations of on-orbit conditions, it was demonstrated that a helium purge system could be an effective method for reducing the incoming flux of contaminant species. Although a generalized purge system was employed in conjunction with basic telescope components, the simulation provided data that could be used for further modeling and design of a specific helium injection system. Experimental telescope pressures required for 90% attenuation appeared to be slightly higher (factor of 2 to 5). Cooling the helium purge gas and telescope components from 300 to 140 K had no measurable effect on stopping efficiency of a given mass flow of helium from the diffuse injector.

Hetrick, M. A.↗

DOE OSTI2025

Horizontal 1 K refrigerator with novel loading mechanism for polarized solid targets

We describe a helium evaporation refrigerator used to cool dynamically polarized proton and deuteron targets for electron-scattering experiments using the CEBAF Large Acceptance Spectrometer CLAS12 at Jefferson Lab. The geometry of the CLAS12 detector systems places severe design and construction constraints on the refrigerator and its ancillary equipment, resulting in a horizontal cryostat with a length of 4 m. The 16 cm 3 target samples, consisting of frozen ammonia (NH 3 or ND 3 ), are loaded at the upstream end of the cryostat and moved to the beam-interaction region using a novel transport mechanism. At this location they are cooled with superfluid helium and polarized via dynamic nuclear polarization at 1 K and 5 T. In this manner samples can be replaced and cooled to 1 K in about 30 minutes without disturbing any elements of the electron beam line or particle detection system. In conclusion, we estimate that this method saved 18 days of valuable beam time over the course of a recent, 88-day long experiment.

Evaporation refrigerator↗

NASA NTRS2002

Operating SIRTF for maximum lifetime

The instruments of the Space Infrared Telescope Facility (SIRTF) are cooled directly by liquid helium, while the optical system is cooled by helium vapor. The greater the power dissipation into the liquid helium, the more vapor is produced, and the colder the telescope. Observations at shorter wavelengths do not require telescope temperatures as low as those required at longer wavelengths. By taking advantage of this, it may be possible to extend the helium and mission lifetime by 10% or even 20%.

cryogenics↗

DOE OSTI2020

Elevated temperature mechanical properties of Inconel 617 surface oxide using nanoindentation

Inconel 617 is a principal candidate material for helium gas cooled very-high-temperature reactors with outlet temperatures of 700–950 °C. Recent findings showed that this alloy develops unique surface oxide layers especially at high temperature (HT) helium environment with distinctive wear, friction and contact properties. This study investigates the elevated temperature mechanical properties of Inconel 617 top surface layers aged in HT helium environment. Nanoindentation technique is used to obtain load-displacement graphs of the alloy top surface oxide in temperatures ranging from 25 °C up to 600 °C. In addition, using finite element analysis along with an iterative regression technique, a semi-numerical method is developed to further measure and quantify the material parameters and, in particular, time-independent and creep characteristics of the oxide. Although Young's modulus of the oxide is found to be relatively close to the bulk for the tested temperatures, the yield strength and hardness, in comparison to the bulk material, increase significantly as the material is oxidized after aging. The oxide exhibits significant softening as the temperature increases to 600 °C. Unlike the bulk material, diffusion through the grains is found to be the dominant creep mechanism for the oxide. Considerable difference between the mechanical properties of the oxide and the bulk material shows the need for accurate measurements of near surface mechanical properties, if reliable predictive contact and tribological models are sought at elevated temperatures.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Design Overview of a High-Pressure Helium Flow Visualization Apparatus for Blanket Cooling Studies

Cooling of the fusion blanket first wall remains a significant challenge given the adverse conditions of heat and particle flux encountered near the plasma. Helium emerges as an attractive cooling candidate because of its chemical and neutronic inertness and separability from hydrogenic species (e.g. tritium). Because of the low thermal mass of helium, optimization of these coolant channels is warranted to provide high heat transfer performance at low pumping costs. Increasingly, computational fluid dynamics (CFD) simulations are employed to model and optimize these flow channels, and accompanying experimental data are needed to validate the predictions of these models. To provide the aforementioned experimental data, a high-pressure helium flow visualization upgrade has been designed for the Helium Flow Loop Experiment facility. This apparatus was built to American Society of Mechanical Engineers boiler and pressure vessel standards to withstand operating pressure of 4 MPa and mated to high-pressure glass windows. Seedless flow visualization is performed via high-speed background oriented schlieren (BOS), with image correlation used for time-resolved two-dimensional velocimetry at frequencies in excess of 60 kHz. Rectangular flow channel test articles are additively manufactured via laser powder bed fusion and installed into this visualization apparatus, with one-sided heating supplied by resistive heaters. In conclusion, the chosen test geometries were informed by prior CFD simulations, and the helium flow structures observed via BOS (detachment, recirculation, etc.) will be used for the validation of these accompanying models, in support of the design and optimization of blanket cooling channel configurations.

Helium flow↗

DOE OSTI2024

Atomic resolution scanning transmission electron microscopy at liquid helium temperatures for quantum materials

Fundamental quantum phenomena in condensed matter, ranging from correlated electron systems to quantum information processors, manifest their emergent characteristics and behaviors predominantly at low temperatures. This necessitates the use of liquid helium (LHe) cooling for experimental observation. Atomic resolution scanning transmission electron microscopy combined with LHe cooling (cryo-STEM) provides a powerful characterization technique to probe local atomic structural modulations and their coupling with charge, spin and orbital degrees-of-freedom in quantum materials. However, achieving atomic resolution in cryo-STEM is exceptionally challenging, primarily due to sample drifts arising from temperature changes and noises associated with LHe bubbling, turbulent gas flow, etc. In this work, we demonstrate atomic resolution cryo-STEM imaging at LHe temperatures using a commercial side-entry LHe cooling holder. Firstly, we examine STEM imaging performance as a function of He gas flow rate, identifying two primary noise sources: He-gas pulsing and He-gas bubbling. Secondly, we propose two strategies to achieve low noise conditions for atomic resolution STEM imaging: either by temporarily suppressing He gas flow rate using the needle valve or by acquiring images during the natural warming process. Lastly, we show the applications of image acquisition methods and image processing techniques in investigating structural phase transitions in Cr 2 Ge 2 Te 6 , CuIr 2 S 4 , and CrCl 3 . In conclusion, our findings represent an advance in the field of atomic resolution electron microscopy imaging for quantum materials and devices at LHe temperatures, which can be applied to other commercial side-entry LHe cooling TEM holders.

36 MATERIALS SCIENCE↗

NASA NTRS1976

The role of Coulomb collisions in limiting differential flow and temperature differences in the solar wind

Data obtained by OGO 5 are used to confirm IMP 6 observations of an inverse dependence of the helium-to-hydrogen temperature ratio in the solar wind on the ratio of solar-wind expansion time to the Coulomb-collision equipartition time. The analysis is then extended to determine the relation of the difference between the hydrogen and helium bulk velocities (the differential flow vector) with the ratio between the solar-wind expansion time and the time required for Coulomb collisions to slow down a beam of ions passing through a plasma. It is found that the magnitude of the differential flow vector varies inversely with the time ratio when the latter is small and approaches zero when it is large. These results are shown to suggest a model of continuous preferential heating and acceleration of helium (or cooling and deceleration of hydrogen), which is cancelled or limited by Coulomb collisions by the time the plasma has reached 1 AU. Since the average dependence of the differential flow vector on the time ratio cannot explain all the systematic variations of the vector observed in corotating high-velocity streams, it is concluded that additional helium acceleration probably occurs on the leading edge of such streams.

Neugebauer, M.↗

DOE OSTI2025

Design and Analysis of the Open-Surface Slow Li Flow Divertor and Comparison to the Fast Li Flow Divertor

In the ongoing U.S. project, “Liquid Metal Plasma Facing Components,” sponsored by the U.S. Department of Energy, efforts have been taken to develop two open-surface divertor designs for the Fusion Nuclear Science Facility using liquid lithium (Li) as a heat and particle flux removal media. The main focus of this study is the design and analysis of a slow (~1 mm/s) and thin (<1 mm) open-surface Li flow divertor with a Li-cooled substrate, which is then compared with an earlier design of a fast (up to 10 m/s) and thick (~0.5 cm) Li flow divertor with the substrate cooled with helium. The slow Li flow divertor design is based on the original LiWall concept developed at the Princeton Plasma Physics Laboratory. Such a thin and slow Li layer can remove the particle flux by reducing the recycling flux, while the heat flux is removed mainly through the heat sink located beneath. In the present study, the heat sink is provided through a Li cooling flow inside the substrate of reduced activation ferritic/martensitic steel. By performing a multiphysics analysis with COMSOL that included liquid-metal magnetohydrodynamics (MHD), heat transfer, and structural mechanics, the impact of various factors on the divertor heat removal capability, such as Li flow velocity, MHD effects, and inlet velocity boundary condition, were examined. Based on comparisons of the two divertor designs, it was shown that the fast-flow divertor significantly outperformed the slow-flow design, whose heat removal capability was limited to ~1 to 2 MW/m2.

Jiang, Yuchen [ORNL] (ORCID:0000000283280284)↗

DOE OSTI2021

Northstar Accelerator Based Mo99 Production Facility Design Support

Facility design support in FY20 centered on transfer of the target insertion and design details to MBraun and Springs, the companies under contract via Northstar to do the hot cell, target insertion and the local target shielding. A significant number of changes have been introduced by these vendors which have been reviewed and critiqued. In addition, the company contracted to produce the Mo100 disks announced that the tolerance on the thickness of 0.5 mm would be ±25%. An alternative design of the target holder was proposed. Bulk shielding and local target shielding design work has continued also and will be reported. Ongoing design and cooling issues continue to arise as the facility takes shape and moves toward completion. LANL is part of the team identifying, analyzing and designing solutions to these issues. Many of these are covered in this report.

43 PARTICLE ACCELERATORS↗

NASA NTRS1994

Development of a Magnetic Refrigerator Operating Between 2K and 10K

An adiabatic demagnetization refrigerator (ADR) is under development at NASA-Ames Research Center that will operate between 2 K and 10 K and will provide 50 mW of cool ng at 2 K. Gadolinium Gallium Garnet (GGG) is selected as the refrigerant for the ADR, To minimize temperature gradients in the GGG, thick slices of GGG are sandwiched together with strips of high-purity copper in between them. The copper strips are used to exchange heat between the GGG and the 2 K and the 10 K heat switches. The heat transfer across the Cu-GGG interfaces is improved by placing thin foils of' high-purity indium at the interfaces. The heat switches employed in the ADR have no moving parts. The 10 K heat switch is a helium gas-gap heat switch; while, the 2 K heat switch is a He ll-gap heat switch. A switch is on when its gap Is filled with helium and is off' when the gap is emptied. This is accomplished with an activated carbon pump (ACP). The ACP adsorbs helium when cooled and desorbs it when heated. A superconducting magnet capable of providing 9 T at 2 K is used for the ADR cycle. A prototype of this refrigerator has been built and is currently under test. A detailed design of the ADR and preliminary test results performed on the prototype ADR will be presented.

Lane, David A.↗

DOE OSTI2022

Transformational challenge reactor design characteristics

The Transformational Challenge Reactor (TCR) program was conceived with the goal to reduce costs and time frames associated with advanced reactor deployment by leveraging developments in advanced manufacturing, advanced materials, data science, and rapid prototyping and testing. The final deliverable of the TCR program was to be an operational test of a novel reactor design. The TCR core design incorporates a dense tri-structural-isotropic/SiC fuel form and volumetrically efficient yttrium hydride moderator, both of which were manufactured and characterized under the TCR program. The TCR is a 3 MW{sub th} He-cooled experimental nuclear reactor designed to reach a total integrated burnup of less than 24 effective full-power hours to keep the radioactive source term to a very low level. TCR design process revealed a positive moderator coefficient; however, the negative doppler coefficients for the fuel and thermal expansion of fuel, moderator, and core support plate yield an overall negative reactivity coefficient. Calculated fuel element temperatures and stresses are well within safety margins. The maximum hypothetical accident (i.e., de-pressurized loss of forced cooling) yields only a modest increase in reactor temperatures that are all within safety margins. This paper summarizes the high-level TCR design characteristics, which were derived from neutronics, thermohydraulics, thermomechanics, and safety analyses.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

NASA NTRS1987

Design concepts for the ASTROMAG cryogenic system

Described is a proposed cryogenic system used to cool the superconducting magnet for the Space Station based ASTROMAG Particle Astrophysics Facility. This 2-meter diameter superconducting magnet will be cooled using stored helium II. The paper presents a liquid helium storage concept which would permit cryogenic lifetimes of up to 3 years between refills. It is proposed that the superconducting coil be cooled using superfluid helium pumped by the thermomechanical effect. It is also proposed that the storage tank be resupplied with helium in orbit. A method for charging and discharging the magnet with minimum helium loss using split gas-cooled leads is discussed. A proposal to use a Stirling cycle cryocooler to extend the storage life of the cryostat will also be presented.

Green, M. A.↗

NASA NTRS1988

Design concepts for the ASTROMAG cryogenic system

Green, M. A.↗

DOE OSTI2022

Pulling thin single crystal silicon wafers from a melt: The new leading-edge solar substrate

The Floating Silicon Method (FSM) has been established as a viable, stable method for growing single crystal ribbons directly from a silicon melt. With intense helium jet cooling to drive the linear progress of a [111] facet, pulled in the <110> direction, ribbons in the 0.6 – 3.0 mm thickness range can be grown at linear growth rates from 0.3 mm/s to >6 mm/s as reported in the literature. We report on recent progress towards growing (100) oriented ribbons with a net thickness of less than 200 microns and a ribbon width up to 18 cm using a stable, continuous process in the Leading Edge prototype furnace. Here, the 3D details of the single crystal growth are explained by extending the mechanics of the Limit Cycle Theory, with novel Internal Side Effect morphology described by a proposed Facet Flow Theory. Grown-in crystalline defect distributions are described as well as values of critical impurities like oxygen, carbon, dopants, and metals that are relevant for use as wafers for solar cells.

14 SOLAR ENERGY↗

DOE OSTI2021

CFD Simulation of Helium Flow Loop Test Section

A helium flow loop is being assembled at Oak Ridge National Laboratory to analyze heat transfer enhancement for systems such as blanket and divertor components. To efficiently identify optimum geometries for heat transfer enhancement in these applications, simulation work is performed to optimize test section designs that are built and tested in the helium flow loop that operates at 4 MPa and a mass flow rate of 100 g/s. Different ribbed geometries that examine rib shape, rib height, rib orientation, rib spacing, and three dimensional orientation are modeled and simulated in STAR-CCM+ to compare their ability to remove heat and mitigate pressure drop. Following the simulations, models are selected and manufactured for the helium flow loop tests. Simulations initially focus on a hydrodynamic study to determine the appropriate mesh and physics models and then add a heat flux to analyze the heat transfer abilities of the models. The simulations are run in steady state and use a Reynolds-averaged Navier-Stokes k-ε turbulence model. The helium is modeled as an ideal gas. The simulation explores models of geometries that enhance the heat transfer and decrease pressure drop with an overall goal of increasing fluid collision with the wall. Enhanced geometries are simulated to select appropriate designs for manufacturing, and preliminary experimental results are used to validate the simulations. Furthermore, the factors that are being analyzed in the comparison between the experimental and the simulated results include matching thermocouple temperatures, pressure drop, roughness, and fluid velocity.

42 ENGINEERING↗

DOE OSTI2020

Magnesium abundances in cool metal-polluted white dwarfs

ABSTRACT The accretion of rocky material is responsible for the presence of heavy elements in the atmospheres of a large fraction of white dwarf stars. Those objects represent a unique opportunity to infer the bulk composition of exoplanetesimals. This chemical characterization requires the use of detailed atmosphere models to determine the elemental abundances at the photospheres of white dwarfs. In this work, we use a state-of-the-art model atmosphere code to reanalyse the first large survey of metal-polluted white dwarfs for which abundances are found for multiple elements. We show that the improved constitutive physics of our models lead to systematically higher Mg abundances than previous analyses. We find an average $\log \, {\rm Mg/Ca}$ number abundance ratio of 1.5. This value is significantly above the reference abundance for chondrites, which is expected as current diffusion models predict that for the cool helium-atmosphere white dwarfs of our sample, Mg should remain in the atmosphere longer than Ca. This helps resolve a recently identified Mg depletion problem, where the planetesimals accreted by white dwarfs were reported to be Mg-deficient compared to the expected composition of their planetary systems.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2022

Clean quantum point contacts in an InAs quantum well grown on a lattice-mismatched InP substrate

Strong spin-orbit coupling, the resulting large g factor, and small effective mass make InAs an attractive material platform for inducing topological superconductivity. The surface Fermi level pinning in the conduction band enables highly transparent ohmic contact without excessive doping. In this study, we investigate electrostatically defined quantum point contacts (QPCs) in a deep-well InAs two-dimensional electron gas. Despite the 3.3% lattice mismatch between the InAs quantum well and the InP substrate, we report clean QPCs with up to eight pronounced quantized conductance plateaus at zero magnetic field. Source-drain dc bias spectroscopy reveals a harmonic confinement potential with a nearly 5 meV subband spacing. We find a many-body exchange interaction enhancement for the out-of-plane g factor |$g^{*}_{⊥}$|=27±1 , whereas the in-plane g factor is isotropic |$g^{*}_{x}$|=|$g^{*}_{y}$|=12±2 , close to the bulk value for InAs.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗