Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fuel Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Mapping the combustion modes of a dual-fuel compression ignition engine

Compression-ignition (CI) engines can produce higher thermal efficiency (TE) and thus lower carbon dioxide (CO 2 ) emissions than spark-ignition (SI) engines. Unfortunately, the overall fuel economy of CI engine vehicles is limited by their emissions of nitrogen oxides (NO x ) and soot, which must be mitigated with costly, resource- and energy-intensive aftertreatment. NO x and soot could also be mitigated by adding premixed gasoline to complement the conventional, non-premixed direct injection (DI) of diesel fuel in CI engines. Several such “dual-fuel” combustion modes have been introduced in recent years, but these modes are usually studied individually at discrete conditions. This paper introduces a mapping system for dual-fuel CI modes that links together several previously studied modes across a continuous two-dimensional diagram. This system includes the conventional diesel combustion (CDC) and conventional dual-fuel (CDF) modes; the well-explored advanced combustion modes of HCCI, RCCI, PCCI, and PPCI; and a previously discovered but relatively unexplored combustion mode that is herein titled “Piston-split Dual-Fuel Combustion” or PDFC. Tests show that dual-fuel CI engines can simultaneously increase TE and lower NO x and/or soot emissions at high loads through the use of Partial HCCI (PHCCI). At low loads, PHCCI is not possible, but either PDFC or RCCI can be used to further improve NO x and/or soot emissions, albeit at slightly lower TE. These results lead to a “partial dual-fuel” multi-mode strategy of PHCCI at high loads and CDC at low loads, linked together by PDFC. Drive cycle simulations show that this strategy, when tuned to balance NO x and soot reductions, can reduce engine-out CO 2 emissions by about 1% while reducing NO x and soot by about 20% each with respect to CDC. This increases emissions of unburnt hydrocarbons (UHC), still in a treatable range (2.0 g/kWh) but five times as high as CDC, requiring changes in aftertreatment strategy.

Engineering↗
DOE OSTI2020

Dynamic System Scaling Applied to Zr-4 Cladding under RIA Conditions

The research and development lifecycle for new fuel designs currently has an ideal 20-25 year timeline. Efforts are currrently underway to accelerate fuel design and development using high performance fuel modeling codes and reduced scale experiments with new instrumentation techniques. However current tools available require a full scale prototype to be designed and tested for fuel qualification. The thermal-hydraulics community has leveraged scaling methodologies to use reduced scale integral effect test facilities (Westinghouse AP600/1000, NuScale Power Module) in lieu of building full scale prototypes for reactor design certification. Dynamic System Scaling (DSS) is a recent development to scaling methodologies that enable the tracking and quantification of dynamic scaling distortions experienced throughout a transient. Recent TREAT experiments performed reactivity initiated accident (RIA) pulses on UO2 fuel rodlets in Zr-4 cladding and were accompanied by BISON predictions for the cladding temperature. DSS is applied to pyrometer data of outer cladding temperatures and two BISON predictions after peak cladding temperature has been reached. One BISON case uses a constant gap conductance value between the fuel and cladding and the other using a conventional gap conductance model. Results from the DSS analysis show that there is good agreement between both BISON predictions and the experimental data and that there is not a significant distortion seen between using either gap conductance model.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Durability evaluation of a Fe–N–C catalyst in polymer electrolyte fuel cell environment via accelerated stress tests

In this work, an “atomically-dispersed” iron-nitrogen-carbon (Fe–N–C) catalyst was used to provide a systematic comparison of platinum group metal (PGM)-free electrocatalyst degradation as a function of accelerated stress tests (ASTs) in an acidic polymer electrolyte fuel cell (PEFC). It was determined that the majority of catalyst degradation was caused by cell operation in presence of O 2 . In contrast, potential cycling of the Fe–N–C-containing cathode under inert atmosphere over typical PEFC cathode operation from 0.95 to 0.6 V had little to no effect. The increase in kinetic overpotential is shown to be the major source of the PEFC performance decrease during the ASTs. These results continue to showcase the need for development of robust PGM-free electrocatalysts in concert with improved electrochemical performance.

25 ENERGY STORAGE↗
DOE OSTI2026

Theory Guided Fine‐Tune of Strain Effects in Pt Ternary Alloy via Rare Earth Templating: Achieving High Performance PEMFCs Catalysts

The sluggish kinetics and insufficient durability of platinum-based catalysts remain crucial barriers limiting proton-exchange-membrane fuel cells (PEMFCs) deployment. Here, we report a theory-guided synthesis combined with rare-earth templating to realize a previously inaccessible Pt 5 Co-like phase with tailored atomic-scale strain. Guided by density functional theory (DFT) calculations, we identified that a Pt 5 Co-like sublayer can induce a unique mild compressive strain (−1.24%) to the Pt(111) shell and an optimal *OH binding energy shift (ΔE ≈ 0.11 eV). This shift positions the alloy catalyst near the apex of the oxygen reduction reaction activity volcano. This prediction guided the synthesis of ternary alloy Pt 5 (Ce)Co@Pt multilayer nanoparticles, featuring a Ce-stabilized core, a Pt 5 Co-like sublayer, and a Pt-rich shell. This catalyst demonstrates both exceptionally high activity and durability, achieving a mass activity of 2.6 A∙mg Pt −1 in rotating disk electrode testing. In fuel cell membrane electrode assembly tests, Pt 5 (Ce)Co@Pt achieves a current density of 1.9 A∙cm −2 at 0.7 V under heavy-duty vehicle conditions. Remarkably, it maintains 1.2 A∙cm −2 after 1 80 000 AST cycles, doubling the U.S. DOE 2025 target. This work demonstrates a rational design strategy that DFT-guided strain engineering integrates with rare-earth templating to advance Pt-based catalysts for fuel cell applications.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Generation IV Benchmarking of TRISO Fuel Performance Models Under Accident Conditions Final Report

The Generation IV International Forum (GIF) is a co-operative international endeavor of fourteen members organized to carry out the research and development needed to establish the feasibility and performance capabilities of the next generation nuclear energy systems. GIF selected six reactor technologies, amongst which is the Very High Temperature Reactor (VHTR) that is primarily dedicated to the cogeneration of electricity and hydrogen. The technical basis for VHTR is the tristructural isotropic (TRISO)-coated particle fuel, the graphite as the core structure, helium coolant, as well as the dedicated core layout and lower power density to removal decay heat in a natural way. At the heart of safety features of the VHTR concept lie the TRISO fuel particles that are designed to keep their structural integrity and retain fission products at temperatures up to 1600°C. As part as the design and future operation of VHTRs, a key aspect is the accurate prediction of fuel performance under irradiation and accident conditions. Modeling and simulation allow prediction of TRISO fuel behavior when subject to neutron flux and in high temperature accident scenarios. The refinement of the fuel performance models and codes is performed by comparison to in-pile and out-of-pile experimental data that reproduce the expected irradiation conditions in high temperature gas-cooled reactors (HTGRs). Historically, the International Atomic Energy Agency (IAEA) developed a benchmark dedicated to the validation of predictive methods for fuel and fission product behavior through the Coordinated Research Program CRP-2 (IAEA, 1997). CRP-2 was later updated to cover fuel fabrication, quality assurance, irradiation performance, safety testing, and spent fuel. The scope of the resulting CRP-6 benchmarks focused on HTGR fuel performance and fission product release (IAEA, 2012). Taking advantage of additional TRISO fuel fabrication, irradiation, and safety testing campaigns, GIF launched a Generation IV Benchmarking of TRISO Fuel Performance Models under Accident Conditions in late 2015. This GIF benchmark is a three-year program steered by Idaho National Laboratory (INL, USA). The other participants include the Japan Atomic Energy Agency (JAEA, Japan) and the Korea Atomic Energy Research Institute (KAERI, Korea). The objectives of the benchmark are to: follow on the IAEA CRP benchmarks, (2) model fission product release under accident conditions, (3) compare results obtained by the fuel performance modeling codes of the benchmark participants, and (4) compare these code predictions to experimental data. Safety tests chosen for modeling include the first and second experiments of the Advanced Gas Reactor program (AGR-1 and AGR-2) and the High Flux Reactor (HFR) EU1bis experiment. This report presents the results obtained by the three research institutions using their respective fuel performance modeling codes. Comparisons of the corresponding fission product release predictions are made with experimental data from AGR-1, AGR-2, and HFR-EU1bis. The benchmark results show good agreements between all participants but also show a general trend of over-prediction of the experimental release data, which is mainly attributed to the use of over-estimated diffusion coefficients.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Autonomous Hydrogen Fueling Station

This project “Autonomous Hydrogen Fueling Station” covered the autonomous refueling with both gaseous hydrogen and liquid hydrogen. The part on gaseous hydrogen focused on the development of an autonomous robotic fueling arm that would couple to a fuel cell engine for hydrogen refueling without guidance from the forklift operator and budget period. Research was also covered for the robotic fueling with a commercial vehicle. The second phase of the project created the baseline for an autonomous liquid hydrogen transfer system that would minimize boil off losses by operating at thermodynamically efficient state points. For the development of the robotic fueling arm, testing was conducted to establish a baseline measurement of the accuracy and repeatability of a human operator positioning a lift truck in front of a dispenser. The goal was to establish the range of motion required for an autonomous fueling mechanism to mate a hydrogen nozzle with a receptacle on a fuel cell system installed in a forklift. The final design comprised a selective compliance articulated robot arm (SCARA)-type mechanism with two arms for horizontal motion and a ball screw for vertical movement and color and LIDAR cameras were used for marker identification and proximity awareness to guide the robotic arm to its target receptacle. Initial tests resulted in 199 out of 200 successful attempts at autonomous coupling of the dispensing coupler and a fuel cell engine, without hydrogen. The dispenser prototype was modified to include tubing for both hydrogen fuel and air purge lines, but subsequent tests were confounded by the shoulder motor over current errors which limited the robot from getting to the fully inserted position to achieve a positive latch. Robotic hydrogen refueling was successfully demonstrated over 1.5 hours of testing, Plug completed 29 successful latches with an average number of 4 sequential latches before failure. However, a robot capable of placing the nozzle with more force is required for higher reliability. For budget period two, a small scale (10 kg / transfer) automated control system was designed that would operate valves to control pressure and flow of liquid nitrogen between a source and receiving tank with an aim to minimize boil off losses by operating at the most thermodynamically efficient state points. Control system logic flow and a P&ID were developed prior to system safety characterization via HAZOP. A control narrative and system state points were defined. Delays in approval for a change of project objective and procurement issues precluded the construction and test of the final prototype system.

08 HYDROGEN↗
DOE OSTI2025

Pre-Transient Characterization of MLOF-1 Test Pin

This study focuses on the pre-transient characterization of U-10Zr test and sibling fuel pins for the THOR-M-LOF test series. Using neutron radiography, element contact profilometry (ECP), precise gamma scan (PGS), and gas assay, sampling, and recharge (GASR) analysis, it was confirmed that the fuel pins were intact and suitable for testing. Key fuel behaviors quantified include axial elongation, diametral strain, fluff structure geometry, axial isotope distribution, and fission gas release. Any deviations from historically expected behaviors were investigated and attributed to factors other than the irradiation behavior of the fuel pin. These pre-transient measurements establish a baseline for future post-transient analysis, which will be used to inform fuel performance models and safety criteria for sodium-cooled fast reactors (SFRs). The results will enhance understanding of transient fuel behavior and expand limited data on LOF scenarios.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Enhance BISON Metal Fuel Transient Models and Enable Assessment Based on Out-of-Pile Transient Experiments

In this report, the activities and achievements made by Argonne National Laboratory for the Nuclear Energy Advanced Modeling and Simulation (NEAMS) BISON code metallic fuel validation and verification (V&V) project in FY2023, with a focus on the capability development and assessment case development for the out-of-pile transient experiments, are summarized. The liquid cladding penetration model was improved based on a comprehensive set of fuel behavior test apparatus (FBTA) test results. The new model was implemented into BISON along with a simple model to account for fuel melting effects. The metallic fuel meshing capability was also upgraded to allow local refinement using unstructured triangular mesh. Based on the previous success in developing the BISON-FIPD integration powered BISON assessment case, this database enabled BISON evaluation and V&V capability was expanded to the out-of-pile transient experiments by introducing BISON-OPTD integration. A series of initial out-of-pile transient assessment cases were implemented into BISON to provide powerful platforms to evaluate current BISON’s capabilities in simulating metallic fuel performance during out-of-pile transients. The established capabilities will also benefit the calibration and V&V of future advanced mechanistic models.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Solution combustion synthesis of iron-based alumina catalysts for dehydrogenation of fossil fuels

Microwave-assisted thermocatalytic dehydrogenation of fossil fuels has been proposed as a method for hydrogen production with no CO2 emissions. The byproduct is carbon, which has a commercial value. Iron-based alumina nanocomposites are promising catalysts for this process as they both absorb microwave radiation and catalyze the dehydrogenation. In addition, they may have magnetic properties, which could be used for their separation from the carbon byproduct. Solution combustion synthesis (SCS) is an attractive technique for the fabrication of iron-based alumina nanocomposites because it can produce high specific surface area oxides in a facile manner. However, the effects of the heating mode, the fuel, and the iron/aluminum ratio on the combustion synthesis behavior and the product properties have not been studied yet. In the present work, the iron-based alumina nanocomposites were obtained by SCS using a hotplate, a muffle furnace, and a microwave oven. The initial mixtures were aqueous solutions of iron nitrate, aluminum nitrate, and an organic fuel. The concentrations of the two nitrates were varied in proportion to Fe:Al molar ratios of 1:2, 1:1, and 2:1. Two fuels were tested: citric acid and glycine. The combustion was less vigorous when citric acid was used as the fuel, which is explained by the lower exothermicity of the reaction. X-ray diffraction analysis of the products confirmed the formation of complex oxides of Fe and Al, specifically it detected hercynite and magnetite phases. Brunauer-Emmett-Teller surface area analysis has shown that the powders obtained using citric acid have specific surface areas as high as 276 m2/g, significantly higher than those obtained using glycine. Muffle furnace and hotplate heating led to comparable specific surface areas, while microwave heating resulted in significantly lower specific surface areas. The magnetic properties of the products increase with increasing the Fe/Al molar ratio from 1:2 (no response to a magnetic field) to 1:1 (weak response) and 2:1 (strong response).

solution combustion synthesis, nanoscale oxides, f↗
DOE OSTI2025

Future TRISO fuel irradiations in the Advanced Test Reactor

AGR-5/6/7 was thought to be the last experiment in the AGR series and the last experiment directly sponsored by DOE. Over the last five years three developments have caused a reevaluation of that assumption. First is that interest in TRISO fueled reactors has spiked dramatically. Virtually all of the new reactor designs are for SMRs or micro-reactors . Some of these reactors use new fuel designs with higher concentrations of U235. This results in changes to the particle design and even fuel pellet design. Second, a design flaw in AGR-5/6/7 Capsule 1 produced a large number of particle failures which resulted in the loss of data from Capsule 1. An additional irradiation could fill in this lost data set. Thirdly, many reactor developers have decided to use AGR spec fuel but different irradiation goals have been identified.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

USHPRR MP-1 Irradiation Test: Assessment of Edge Pitting and Bond Line Corrosion in Vendor Produced Fuel Plates

This report summarizes an effort to identify the source of anomalous localized edge pitting and bond line corrosive attack of experimental mini fuel plates manufactured at the commercial fuel vendor BWXT and tested in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) as part of the Miniplate 1 (MP-1) irradiation test. The MP-1 test was conducted by the US High Performance Research Reactor Project (USHPRR) and overseen by the Fuel Qualification Pillar (FQ). The test involved evaluation of a mix of 62 “vendor” fuel plates fabricated at BWXT and 12 “laboratory” fuel plates fabricated at Idaho National Laboratory using commercial-scale and labscale fabrication processes respectively. The MP-1 test was the first in a series of tests to generate data to support qualification of a new plate-type low-enriched uranium (LEU) U-10Mo monolithic fuel system. The major objective of the MP-1 experiment was to test, for the first time, miniplates fabricated by a commercial fuel vendor over the range of irradiation conditions relevant to conversion of NRC regulated High Performance Research Reactors (HPRRs) from high-enriched uranium to LEU. The focus of the efforts described in this report are the vendor fuel plates to inform changes in the fabrication process prior to fabrication of the next miniplate experiment MP2.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Analysis of Uncertainty Impacts on Emissions and Fuel Economy Evaluation for Chassis Dynamometer Testing

This study illustrates a methodology for quantifying the uncertainties encountered in the measurement of tailpipe emissions and in the fuel consumption measurements for light-duty conventional vehicles tested on a four-wheel drive chassis dynamometer. The study leverages high-fidelity experimental data collected over three standard drive cycles, UDDS, HWY and US06, intended to simulate a wide range of operating conditions. Here, a method is developed to estimate the measurement uncertainties in fuel consumption for a test cycle, which occur due to the accumulation of measurement uncertainties propagated through the system. The uncertainty determination model uses statistical analysis and standard propagation techniques to evaluate and combine the uncertainties introduced from various sources (including the vehicle, chassis dynamometer, driver, and instrumentation). The analysis also examines three different experimental methods for determining the fuel consumption: 1) carbon mass balance, 2) volumetric fuel scale and 3) gravimetric fuel scale, and takes into consideration the properties of the instrumentation used. The results show that the most significant influence on the determination of the emissions comes from the concentration measurement, and similarly the biggest impact on the total fuel consumption uncertainty comes from the uncertainty in the determination of the carbon dioxide mass, due to the large presence of this pollutant in the overall emissions. It was found that the fuel consumption uncertainties are in the range of ±1-2% for all three methods analyzed, with the lowest values being obtained for measurements performed using the gravimetric method for all three drive cycles considered.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Development and demonstration of a BISON–Griffin modeling framework for the design of targeted TRISO transient experiments in the Transient Reactor Test Facility

Uranium oxycarbide (UCO)-bearing tri-structural isotropic (TRISO) particle fuels are expected to be used in numerous U.S. commercial reactor applications within the next decade. Here, in this work, we reviewed historical particle fuel transient experiments to identify gaps in TRISO fuel performance transient testing. A BISON–Griffin modeling framework was then developed to conduct preliminary TRISO transient analyses and begin to address these gaps. The framework was demonstrated using limiting-case transient conditions from a prototypic high-temperature gas-cooled reactor (HTGR). It was then applied to develop a matrix of experiments that could be performed in the Transient Reactor Test Facility (TREAT) to (1) evaluate UCO-fueled particle performance at moderate and high heat rates, (2) assess whether historical testing involving UO 2 -fueled particles is applicable to modern UCO-fueled particles, (3) deconvolute the impacts of temperature and heat rate on particle transient response, and (4) collect the data needed for fuel performance model validation and/or further development.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

NCSP Integral Experiments at Sandia in FY21 [Slides]

This presentation provides details regarding integral experiments at Sandia National Laboratory for fiscal year 2021. The experiments discussed are as follows: IER 230: Characterize the Thermal Capabilities of the 7uPCX; IER 304: Temperature Dependent Critical Benchmarks; IER 305: Critical Experiments with UO 2 Rods and Molybdenum Foils; IER 306: Critical Experiments with UO 2 Rods and Rhodium Foils ; IER 441: Epithermal HEX Lattices with SNL 7uPCX Fuel for Testing Nuclear Data; IER 452: Inversion Point of the Isothermal Reactivity Coefficient; and IER 523: Critical Experiments with ACRR UO 2 -BeO Fuel.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

Specimen Size Artifacts Associated with a Glovebox Deployable Laser Flash Diffusivity Measurement System

To accelerate nuclear fuel qualification and deployment efforts, Oak Ridge National Laboratory has led the world in developing vehicles for accelerating burnup accumulation in nuclear fuel by testing miniature samples in the High Flux Isotope Reactor. However, a challenge remains to establish parity between post irradiation characterization methods for miniature fuel specimens in comparison to conventional fuel elements. This work aims to identify artifacts associated with the thermal analysis of miniature disk specimens in comparison to samples of standardized dimensions through a combination of experimental and computational tools. Using a newly procured Netzsch 427 laser flash diffusivity system, preliminary data on mild steel specimens were collected, and finite element techniques were used to model heat transfer using 1D conditions to assess issues associated with pulse width and data collection frequency effects. These preliminary investigations found that significant variability in measured thermal diffusivity exist within datasets. These variations are not necessarily attributed to limitations with respect to data collection rate; nor are they associated with limitations on pulse width. Instead, these artifacts may be a result of limitations in detector intensity. Future work aims to design a focusing lens to better measure the smaller surface area of miniature specimens analyzed using the laser flash analysis system.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

THERMAL SAFETY MARGIN CALCULATION OF THE MP-2 EXPERIMENT IN THE ADVANCED TEST REACTOR

The Mini-Plate 2 (MP-2) irradiation test is a fueled experiment designed for irradiation in multiple test locations in the Advanced Test Reactor (ATR) at the Idaho National Laboratory (INL). The experiment is a drop-in test where small aluminum-clad fuel plate samples (mini plates) are cooled directly by the ATR Primary Coolant System (PCS) water. The MP-2 fuel plate experiment will be irradiated in several different irradiation locations of the ATR. This fueled experiment contains aluminum-clad fuel mini plates consisting of monolithic U-Mo. Four different types of fuel plates with fuel meat thickness and cladding are part of the MP-2 test. A thermal analysis has been performed on the MP-2 experiment. A method for calculating Departure from Nucleate Boiling Ratio (DNBR) and Flow Instability Ratio (FIR) during a reactivity transient using the commercial finite element and heat transfer code ABAQUS is discussed. At the start of an ATR cycle the heat generation rate of the fueled experiment is high and the heat rate multiplier from the outer shim control cylinders is low, while the reverse is true at the end of the ATR cycle. Thermal analyses at 10 day increments during the cycle calculate the DNBR and FIR during a reactivity transient. This technique calculates DNBR for the fuel plate surfaces and FIR for all water components for each finite element surface and node at various times during the ATR cycle. Heat rates vary with time during the transient calculation that are provided by a detailed physics analysis. Oxide growth on the fuel plates is also incorporated Results from the transient calculations are displayed with the ABAQUS post processor. By calculating these parameters at each location in the finite element model, conservatism is replaced with accuracy. This allows for a greater margin for the thermal hydraulic safety parameters.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Continuous hydrodeoxygenation of lignin to jet-range aromatic hydrocarbons

Sustainable aviation fuel (SAF) is essential to decrease the carbon footprint of the aviation industry. Although many strategies have been developed to provide the branched, aliphatic components of SAF, few viable strategies have been demonstrated to supply the aromatic and cycloalkane fraction of SAF at the necessary scale from bio-based feedstocks. Lignin is the largest natural source of renewable aromatic compounds, yet major challenges in deoxygenation have prevented its use as a feedstock for SAF. Here we report a continuous, two-stage catalytic process using molybdenum carbide to deoxygenate lignin from poplar into aromatic hydrocarbons with 87.5% selectivity towards aromatic hydrocarbons at 86% of the theoretical carbon recovery. This work demonstrates an effective approach to convert lignin into aromatic SAF blendstocks.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Understanding fission gas bubble distribution, lanthanide transportation, and thermal conductivity degradation in neutron-irradiated α-U using machine learning

U—10Zr based metallic nuclear fuel is the leading candidate for next-generation sodium-cooled fast reactors in the United States. US research reactors have used and tested this fuel type since the 1960s and accumulated considerable experience and knowledge about the fuel performance. Most of the knowledge, however, remains empirical. The lack of mechanistic understanding of fuel performance puts a large burden on proof through experimental verification for the qualification of U—10Zr fuel for commercial use. Further, this paper proposes an image data-driven machine learning approach, coupled with domain knowledge provided by advanced post irradiation examination, to provide unprecedented quantified insights into the morphology, size, density and the connectivity of fission gas bubbles and their effects on the fission product transportation and thermal conductivity. Specifically, we developed a method to automatically detect, extract statistics, and classify ~19,000 fission gas bubbles into different categories, and quantitatively link the data to lanthanide transportation through connected bubbles and degradation of thermal conductivity along the radial temperature gradient in a neutron irradiated U—10Zr annular fuel. Results indicate the approach can be modified to study other irradiation effects, such as secondary phase redistribution and gaseous fuel swelling in other irradiated nuclear fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗