SEARCH · Engineering Papers

Results for “Freestream Velocity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

All sources NASA NTRS DOE OSTI

NASA NTRS1974

Effect of forward velocity on the noise characteristics of dual-flow jet nozzles

Acoustic results of jet noise tests conducted on scale-model nozzles at a wall isolation facility are presented and analyzed. The test fixture featured a triple-flow system for the purpose of simulating freestream flow around hot dual-flow jet nozzles. Test nozzles included 1/20th scale models of the exhaust system for the JT8D-9 engine, power plant for the Boeing 727 airplane (bypass ratio 1) and of the JT8D-109 refan engine (bypass ratio 2). It was found that overall jet noise is reduced by the forward velocity in proportion to the fifth and sixth power of the relative primary jet velocity. Spectral and directivity characteristics are presented.

Reed, D. H.↗

NASA NTRS2012

Plume-Free Stream Interaction Heating Effects During Orion Crew Module Reentry

During reentry of the Orion Crew Module (CM), vehicle attitude control will be performed by firing reaction control system (RCS) thrusters. Simulation of RCS plumes and their interaction with the oncoming flow has been difficult for the analysis community due to the large scarf angles of the RCS thrusters and the unsteady nature of the Orion capsule backshell environments. The model for the aerothermal database has thus relied on wind tunnel test data to capture the heating effects of thruster plume interactions with the freestream. These data are only valid for the continuum flow regime of the reentry trajectory. A Direct Simulation Monte Carlo (DSMC) analysis was performed to study the vehicle heating effects that result from the RCS thruster plume interaction with the oncoming freestream flow at high altitudes during Orion CM reentry. The study was performed with the DSMC Analysis Code (DAC). The inflow boundary conditions for the jets were obtained from Data Parallel Line Relaxation (DPLR) computational fluid dynamics (CFD) solutions. Simulations were performed for the roll, yaw, pitch-up and pitch-down jets at altitudes of 105 km, 125 km and 160 km as well as vacuum conditions. For comparison purposes (see Figure 1), the freestream conditions were based on previous DAC simulations performed without active RCS to populate the aerodynamic database for the Orion CM. Other inputs to the analysis included a constant Orbital reentry velocity of 7.5 km/s and angle of attack of 160 degrees. The results of the study showed that the interaction effects decrease quickly with increasing altitude. Also, jets with highly scarfed nozzles cause more severe heating compared to the nozzles with lower scarf angles. The difficulty of performing these simulations was based on the maximum number density and the ratio of number densities between the freestream and the plume for each simulation. The lowest altitude solutions required a substantial amount of computational resources (up to 1800 processors) to simulate approximately 2 billion molecules for the refined (adapted) solutions.

Marichalar, J.↗

NASA NTRSDate not supplied

A Database of CFD-Based Buffet Forcing Functions for Artemis I Structural Response Evaluation

Time-accurate FUN3D simulations are utilized to estimate buffet-induced unsteady forces experienced by the Space Launch System during the Artemis I (AR01) flight. A set of FUN3D simulations was developed that employed time-accurate mesh translations to simulate the changing velocity and attitude based on the AR01 best estimated trajectory. In these simulations, referred to as accelerating-flow simulations, the freestream Mach number increased from 0.80 to 1.92. Additional time-accurate simulations were obtained at constant freestream Mach number equal to 0.95, 1.18, 1.70, thereby simulating stationary conditions experienced by the flow in a wind-tunnel. On the grounds of favorable comparisons between simulated and flight-measured environments, the FUN3D-based surface pressures were utilized to develop a buffet forcing function (BFF) database. This BFF database was analyzed to characterize the spatial distribution and frequency content of the buffet forces during transonic and supersonic portions of the AR01 flight. The region of interest is located downstream of the forward attachment (FA) hardware between the core stage and the solid rocket boosters where vortex shedding off the FA protuberance produces significant unsteadiness. The analysis reveals that, at transonic and supersonic conditions, buffet forces that are based on constant freestream Mach number data are a good approximation of those based on accelerating-flow simulations.

FUN3D↗

NASA NTRSDate not supplied

A Database of CFD-Based Buffet Forcing Functions for Artemis I Structural Response Evaluation

transonic buffet↗

NASA NTRS2012

CFD Simulations for the Effect of Unsteady Wakes on the Boundary Layer of a Highly Loaded Low-Pressure Turbine Airfoil (L1A)

This report is the third part of a three-part final report of research performed under an NRA cooperative Agreement contract. The first part was published as NASA/CR-2012-217415. The second part was published as NASA/CR-2012-217416. The study of the very high lift low-pressure turbine airfoil L1A in the presence of unsteady wakes was performed computationally and compared against experimental results. The experiments were conducted in a low speed wind tunnel under high (4.9%) and then low (0.6%) freestream turbulence intensity for Reynolds number equal to 25,000 and 50,000. The experimental and computational data have shown that in cases without wakes, the boundary layer separated without reattachment. The CFD was done with LES and URANS utilizing the finite-volume code ANSYS Fluent (ANSYS, Inc.) under the same freestream turbulence and Reynolds number conditions as the experiment but only at a rod to blade spacing of 1. With wakes, separation was largely suppressed, particularly if the wake passing frequency was sufficiently high. This was validated in the 3D CFD efforts by comparing the experimental results for the pressure coefficients and velocity profiles, which were reasonable for all cases examined. The 2D CFD efforts failed to capture the three dimensionality effects of the wake and thus were less consistent with the experimental data. The effect of the freestream turbulence intensity levels also showed a little more consistency with the experimental data at higher intensities when compared with the low intensity cases. Additional cases with higher wake passing frequencies which were not run experimentally were simulated. The results showed that an initial 25% increase from the experimental wake passing greatly reduced the size of the separation bubble, nearly completely suppressing it.

Vinci, Samuel, J.↗

NASA NTRS1988

Correlations of velocity and temperature fluctuations in the stagnation-point flow of circular cylinder in turbulent flow

The present analyses of boundary layer flow and turbulence transport attempt to characterize the influence of freestream turbulence on the surface heat-transfer rate and stagnation point region skin friction of a circular cross-section cylinder in turbulent flow. The Reynolds stress-transport equations and k-epsilon two-equation turbulence modeling are used, yielding time-averaged turbulence double-correlations, mean-flow properties, surface heat-transfer rate, and skin-friction with freestream isotropic turbulence. A comparison of analytical results with experimental data indicates that large Reynolds normal stresses are induced at the boundary layer edge by the kinetic energy of the turbulence.

Wang, C. R.↗

NASA NTRS1984

Shapes for rotating airfoils

An airfoil which has particular application to the blade or blades of rotor aircraft and aircraft propellers is presented. The airfoil thickness distribution, camber and leading edge radius are shaped to locate the airfoil crest at a more aft position along the chord, and to increase the freestream Mach number at which sonic flow is attained at the airfoil crest. The reduced slope of the airfoil causes a reduction in velocity at the airfoil crest at lift coefficients from zero to the maximum lift coefficient. The leading edge radius is adjusted so that the maximum local Mach number at 1.25 percent chord and at the designed maximum lift coefficient is limited to about 0.48 when the Mach number normal to the leading edge is approximately 0.20. The lower surface leading edge radius is shaped so that the maximum local Mach number at the leading edge is limited to about 0.29 when the Mach number normal to the leading edge is approximately 0.20. The drag divergence Mach number associated with the airfoil is moved to a higher Mach number over a range of lift coefficients resulting in superior aircraft performance.

Bingham, G. J.↗

NASA NTRS1992

A study of the rotor wake of a small-scale rotor model in forward flight using laser light sheet flow visualization with comparisons to analytical models

An experimental investigation was conducted in the 14 by 22 ft subsonic tunnel at NASA Langley Research Center to quantify the rotor wake behind a scale model helicopter rotor in forward flight (mu = 0.15 and 0.23) at one thrust level (C sub T = 0.0064). The rotor system used in the present test consisted of a four-bladed, fully articulated hub and utilized blades of rectangular planform with a NACA-0012 airfoil section. A laser light sheet, seeded with propylene glycol smoke, was used to visualize the flow in planes parallel and perpendicular to the freestream flow. Quantitative measurements of vortex location, vertical skew angle, and vortex particle void radius were obtained for vortices in the flow; convective velocities were obtained for blade tip vortices. Comparisons were made between the experimental results and the wake geometry generated by computational predictions. The results of these comparisons show that the interaction between wake vortex structures is an important consideration for correctly predicting the wake geometry.

Ghee, Terence A.↗

NASA NTRS1992

The effect of a turbulent wake on the stagnation point. II - Heat transfer results

A phenomenological model is proposed which relates the effects of freestream turbulence to the increase in stagnation point heat transfer. The model requires both turbulence intensity and energy spectra as inputs to the unsteady velocity at the edge of the boundary layer. The form of the edge velocity contains both a pulsation of the incoming flow and an oscillation of the streamlines. The incompressible unsteady and time-averaged boundary layer response is determined by solving the momentum and energy equations. The model allows for arbitary two-dimensional geometry, however, results are given only for a circular cylinder. The time-averaged Nusselt number is determined theoretically and compared to existing experimental data.

Hanford, Anthony J.↗

NASA NTRS1995

Direct numerical simulation of transitional and turbulent flow over a heated flat plate using finite-difference schemes

This report deals with the direct numerical simulation of transitional and turbulent flow at low Mach numbers using high-order-accurate finite-difference techniques. A computation of transition to turbulence of the spatially-evolving boundary layer on a heated flat plate in the presence of relatively high freestream turbulence was performed. The geometry and flow conditions were chosen to match earlier experiments. The development of the momentum and thermal boundary layers was documented. Velocity and temperature profiles, as well as distributions of skin friction, surface heat transfer rate, Reynolds shear stress, and turbulent heat flux, were shown to compare well with experiment. The results indicate that the essential features of the transition process have been captured. The numerical method used here can be applied to complex geometries in a straightforward manner.

Madavan, Nateri K.↗

NASA NTRS1995

Direct Numerical Simulation of Transitional and Turbulent Flow Over a Heated Flat Plate Using Finite-Difference Schemes

The work in this report was conducted at NASA Ames Research Center during the period from August 1993 to January 1995 deals with the direct numerical simulation of transitional and turbulent flow at low Mach numbers using high-order-accurate finite-difference techniques. A computation of transition to turbulence of the spatially-evolving boundary layer on a heated flat plate in the presence of relatively high freestream turbulence was performed. The geometry and flow conditions were chosen to match earlier experiments. The development of the momentum and thermal boundary layers was documented. Velocity and temperature profiles, as well as distributions of skin friction, surface heat transfer rate, Reynolds shear stress, and turbulent heat flux were shown to compare well with experiment. The numerical method used here can be applied to complex geometries in a straightforward manner.

Madavan, Nateri K.↗

NASA NTRS2014

Flow-Field Investigation of Gear-Flap Interaction on a Gulfstream Aircraft Model

Off-surface flow measurements of a high-fidelity 18% scale Gulfstream aircraft model in landing configuration with the main landing gear deployed are presented. Particle Image Velocimetry (PIV) and Laser Velocimetry (LV) were used to measure instantaneous velocities in the immediate vicinity of the main landing gear and its wake and near the inboard tip of the flap. These measurements were made during the third entry of a series of tests conducted in the NASA Langley Research Center (LaRC) 14- by 22-Foot Subsonic Tunnel (14 x 22) to obtain a comprehensive set of aeroacoustic measurements consisting of both aerodynamic and acoustic data. The majority of the off-body measurements were obtained at a freestream Mach number of 0.2, angle of attack of 3 degrees, and flap deflection angle of 39 degrees with the landing gear on. A limited amount of data was acquired with the landing gear off. LV was used to measure the velocity field in two planes upstream of the landing gear and to measure two velocity profiles in the landing gear wake. Stereo and 2-D PIV were used to measure the velocity field over a region extending from upstream of the landing gear to downstream of the flap trailing edge. Using a special traverse system installed under the tunnel floor, the velocity field was measured at 92 locations to obtain a comprehensive picture of the pertinent flow features and characteristics. The results clearly show distinct structures in the wake that can be associated with specific components on the landing gear and give insight into how the wake is entrained by the vortex at the inboard tip of the flap.

Yao, Chung-Sheng↗

NASA NTRS1991

Hypersonic cone flow predictions using an implicit upwind space-marching code

Solutions have been computed and results are presented for Problem 1, the case of Mach 9 transitional flow past a 7 deg half-angle cone at zero incidence. The solutions were computed using a code developed for the integration of the parabolized Navier-Stokes equations. The algorithm employed in the code is based on a Roe-type flux-difference-splitting scheme applied following a finite-volume approach. The basic algorithm has been modified to make it implicit and second-order accurate in the crossflow directions. Results are presented in terms of surface pressure and heat transfer as well as boundary layer profiles of pitot pressure, Mach number, and tangential velocity. The case was recalculated several times in an effort to determine sensitivities to such parameters as grid density, wall temperature, turbulence model parameters, as well as freestream expansion. Comparisons with the experimental data are presented and discussed.

Lawrence, Scott L.↗

NASA NTRS1979

Low-Reynolds-number turbulent boundary layers

A test facility operating at substantially reduced pressures is described and shown to be suitable when used with an open-circuit turbulent boundary layer wind tunnel. The facility is capable of producing flows with momentum Reynolds number in the range 200-10,000 by varying the ambient pressure. At low-Reynolds-number flows the pressure is low enough to allow the tunnel to operate with large values of freestream speed. The tunnel's reliability is verified by examining flows where momentum Reynolds number is greater than 1200. The results skin friction coefficients, wake parameters, and basic velocity profiles - consistently agreed with well-established data. For momentum Reynolds number from 600 through 1200 the resulting data indicate that the 'universal velocity profile' is accurate and correctly describes the mean flow properties. For Reynolds number from 425 through 600, the viscous sublayer in this range can no longer maintain its characteristic size.

White, B. R.↗

NASA NTRS1993

An adaptive grid/Navier-Stokes methodology for the calculation of nozzle afterbody base flows with a supersonic freestream

This paper describes an adaptive grid method for base flows in a supersonic freestream. The method is based on the direct finite-difference statement of the equidistribution principle. The weighting factor is a combination of the Mach number, density, and velocity first-derivative gradients in the radial direction. Two key ideas of the method are to smooth the weighting factor by using a type of implicit smoothing and to allow boundary points to move in the grid adaptation process. An AGARD nozzle afterbody base flow configuration is used to demonstrate the performance of the adaptive grid methodology. Computed base pressures are compared to experimental data. The adapted grid solutions offer a dramatic improvement in base pressure prediction compared to solutions computed on a nonadapted grid. A total-variation-diminishing (TVD) Navier-Stokes scheme is used to solve the governing flow equations.

Williams, Morgan↗

NASA NTRS1995

Effect of velocity and temperature distribution at the hole exit on film cooling of turbine blades

An existing three-dimensional Navier-Stokes code, modified to include film cooling considerations, has been used to study the effect of coolant velocity and temperature distribution at the hole exit on the heat transfer coefficient on three-film-cooled turbine blades, namely, the C3X vane, the VKI rotor, and the ACE rotor. Results are also compared with the experimental data for all the blades. Moreover, Mayle's transition criterion, Forest's model for augmentation of leading edge heat transfer due to freestream turbulence, and Crawford's model for augmentation of eddy viscosity due to film cooling are used. Use of Mayle's and Forest's models is relevant only for the ACE rotor due to the absence of showerhead cooling on this rotor. It is found that, in some cases, the effect of distribution of coolant velocity and temperature at the hole exit can be as much as 60% on the heat transfer coefficient at the blade suction surface, and 50% at the pressure surface. Also, different effects are observed on the pressure and suction surface depending upon the blade as well as upon the hole shape, conical or cylindrical.

Garg, Vijay K.↗

NASA NTRS2012

Numerical Study of Pressure Fluctuations due to High-Speed Turbulent Boundary Layers

Direct numerical simulations (DNS) are used to examine the pressure fluctuations generated by fully developed turbulence in supersonic turbulent boundary layers with an emphasis on both pressure fluctuations at the wall and the acoustic fluctuations radiated into the freestream. The wall and freestream pressure fields are first analyzed for a zero pressure gradient boundary layer with Mach 2.5 and Reynolds number based on momentum thickness of approximately 2835. The single and multi-point statistics reported include the wall pressure fluctuation intensities, frequency spectra, space-time correlations, and convection velocities. Single and multi-point statistics of surface pressure fluctuations show good agreement with measured data and previously published simulations of turbulent boundary layers under similar flow conditions. Spectral analysis shows that the acoustic fluctuations outside the boundary layer region have much lower energy content within the high-frequency region. The space-time correlations reflect the convective nature of the pressure field both at the wall and in the freestream, which is characterized by the downstream propagation of pressure-carrying eddies. Relative to those at the wall, the pressure-carrying eddies associated with the freestream signal are larger and convect at a significantly lower speed. The preliminary DNS results of a Mach 6 boundary layer show that the pressure rms in the freestream region is significantly higher than that of the lower Mach number case.

Duan, Lian↗

NASA NTRS1986

A comparison of experimental and numerical results for delta wings with vortex flaps

Computational and experimental results are presented for delta wings with vortex flaps. The wings have an undeflected leading-edge sweep of 75 deg. Flap angles of 5 deg and 10 deg, measured in the streamwise direction, are considered. The nominal angle of attack alpha is varied from 4 deg to 12 deg. Results for freestream Mach numbers of 1.7 and 2.4 are shown. Surface pressure, tuft patterns and vapor screens are given for the experimental data. Surface pressure, tuft patterns, cross-flow velocities, total pressure loss and cross-flow Mach number are given for the numerical data. C(l)-vs-alpha curves are shown for experimental and computational results. The flows are shown to be very sensitive to angle of attack, and the agreement between experimental and theoretical results is improved if the calculations are made at angles of attack slightly larger than the experimental angles of attack. The computational model correctly predicts the topology of the flow in each of the cases considered. The lift is predicted well at the higher angles of attack, but slightly overpredicted at the lower angles of attack.

Powell, K. G.↗