Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fractional operators”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS2018

Performance Calculations for a Boundary-Layer-Ingesting Fan Stage from Sparse Measurements

A test of the Boundary Layer Ingesting-Inlet / Distortion-Tolerant Fan was completed in NASA Glenn's 8-Foot by 6-Foot supersonic wind tunnel. Inlet and fan performance were measured by surveys using a set of rotating rake arrays upstream and downstream of the fan stage. Surveys were conducted along the 100 percent speed line and a constant exit corrected flow line passing through the aerodynamic design point. These surveys represented only a small fraction of the data collected during the test. For other operating points, data was recorded as snapshots without rotating the rakes which resulted in a sparser set of recorded data. This paper will discuss analysis of these additional, lower measurement density data points to expand our coverage of the fan map. Several techniques will be used to supplement the snapshot data at test conditions where survey data also exists. The supplemented snapshot data will be compared with survey results to assess the quality of the approach. Effective methods will be used to analyze the data set for which only snapshots exist.

fan efficiency↗
NASA NTRS1995

q-bosons and the q-analogue quantized field

The q-analogue coherent states are used to identify physical signatures for the presence of a 1-analogue quantized radiation field in the q-CS classical limits where the absolute value of z is large. In this quantum-optics-like limit, the fractional uncertainties of most physical quantities (momentum, position, amplitude, phase) which characterize the quantum field are O(1). They only vanish as O(1/absolute value of z) when q = 1. However, for the number operator, N, and the N-Hamiltonian for a free q-boson gas, H(sub N) = h(omega)(N + 1/2), the fractional uncertainties do still approach zero. A signature for q-boson counting statistics is that (Delta N)(exp 2)/ (N) approaches 0 as the absolute value of z approaches infinity. Except for its O(1) fractional uncertainty, the q-generalization of the Hermitian phase operator of Pegg and Barnett, phi(sub q), still exhibits normal classical behavior. The standard number-phase uncertainty-relation, Delta(N) Delta phi(sub q) = 1/2, and the approximate commutation relation, (N, phi(sub q)) = i, still hold for the single-mode q-analogue quantized field. So, N and phi(sub q) are almost canonically conjugate operators in the q-CS classical limit. The q-analogue CS's minimize this uncertainty relation for moderate (absolute value of z)(exp 2).

Nelson, Charles A.↗
NASA NTRS1988

Microcomputer versus mainframe simulations: A case study

The research was conducted to two parts. Part one consisted of a study of the feasibility of running the Space Transportation Model simulation on an office IBM-AT. The second part was to design simulation runs so as to study the effects of certain performance factors on the execution of the simulation model. The results of this research are given in the two reports which follow: Microcomputer vs. Mainframe Simulation: A Case Study and Fractional Factorial Designs of Simulation Runs for the Space Transportation System Operations Model. In the first part, a DOS batch job was written in order to simplify the execution of the simulation model on an office microcomputer. A comparison study was then performed of running the model on NASA-Langley's mainframe computer vs. running on the IBM-AT microcomputer. This was done in order to find the advantages and disadvantages of running the model on each machine with the objective of determining if running of the office PC was practical. The study concluded that it was. The large number of performance parameters in the Space Transportation model precluded running a full factorial design needed to determine the most significant design factors. The second report gives several suggested fractional factorial designs which require far fewer simulation runs in order to determine which factors have significant influence on results.

Bengtson, Neal M.↗
NASA NTRSDate not supplied

Extraterrestrial Mining Via Two Coupled Thermal-Driven Phenomena

Two-coupled thermal-driven phenomena, Marangoni effect and thermal fractional decomposition under high vacuum, previously observed by the authors could lead to an extraterrestrial mining operation that would significantly reduce mechanical operation and allow in-situ product extraction directly from the mineral without the necessity of neither mineral beneficiation nor use of terrestrial precursors. Thermal Marangoni effect alone and coupled with fractional decomposition have been corroborated through paths of 10 and 13 inches respectively on molten JSC-1A lunar regolith simulant presenting a novel and valuable potential for extraterrestrial mining as the observed outcome (self-transportation via Marangoni effect and fractional decomposition at higher temperature) will be more prominent on extraterrestrial surfaces under higher vacuum and reduced gravity. A comprehensive 3D model built by the authors demonstrated to be a crucial tool to determine the right location of the sample to optimize the gradient temperature along the wall of a long tubular crucible enhancing the Marangoni effect as surface tension (the driving force for the thermal Marangoni effect) depends on the temperature gradient.

Jesus A Dominguez↗
DOE OSTI2024

UEDGE modeling of plasma detachment of CFETR with ITER ‐like divertor geometry by external impurity seeding

Abstract Efficient handling of high heat flux on the plasma‐facing components, particularly the divertor targets, poses a significant challenge for the Chinese Fusion Engineering Testing Reactor (CFETR) with fusion power of Gigawatt. This work investigates the divertor plasma detachment of CFETR with a standard ITER‐like divertor geometry by neon (Ne) or argon (Ar) impurity seeding using UEDGE code. The cross‐field drifts terms are switched off, and fluid neutral models and a “fixed‐fraction” impurity model are applied to enable efficient simulations for the study of CFETR detachment. In order to reduce the heat load on the divertor targets below the acceptable level (<10 MW/m 2 ), the impurity fraction ( f ), pumping speed ( S ), and upstream density are varied to identify the suitable operations window during Ne seeding. The effects of Ne and Ar impurities on the plasma detachment are compared. It is found that with the power across the core‐edge interface P SOL = 200 MW and separatrix density of 2.8 10 19 , Ne impurity fraction ≥1.7%, and Ar impurity fraction ≥0.24% can achieve the partial detachment. Achieving similar total radiation power (˜148 MW), the Ne fraction is 2.3% and the Ar fraction is 0.24%. Moreover, the simulation results indicate that Ar exhibits better power radiation efficiency and core compatibility compared with Ne.

Zhang, M. Z.↗
DOE OSTI2023

Measurement of branching fractions of Λ$^+_c$ → p⁢K$^0_S$K$^0_S$ and Λ$^+_c$ → p⁢K$^0_S$⁢η at Belle

We present a study of a singly Cabibbo-suppressed decay Λ$^+_c$ → p⁢K$^0_S$K$^0_S$ and a Cabibbo-favored decay Λ$^+_c$ → p⁢K$^0_S$⁢η based on 980 fb -1 of data collected by the Belle detector, operating at the KEKB energy-asymmetric e + ⁢e - collider. We measure their branching fractions relative to Λ$^+_c$ → p⁢K$^0_S$: $\mathscr{B}$(Λ$^+_c$ → p⁢K$^0_S$K$^0_S$)/$\mathscr{B}$(Λ$^+_c$ → p⁢K$^0_S$) = (1.48 ± 0.08 ± 0.04) × 10 -2 and $\mathscr{B}$(Λ$^+_c$ → p⁢K$^0_S$η)/$\mathscr{B}$(Λ$^+_c$ → p⁢K$^0_S$) = (2.73 ± 0.06 ± 0.13) × 10 -1 . Combining with the world average $\mathscr{B}$(Λ$^+_c$ → p⁢K$^0_S$), we have the absolute branching fractions, $\mathscr{B}$(Λ$^+_c$ → p⁢K$^0_S$K$^0_S$) = (2.35 ± 0.12 ± 0.07 ± 0.12) × 10 -4 and $\mathscr{B}$(Λ$^+_c$ → p⁢K$^0_S$η) = (4.35 ± 0.10 ± 0.20 ± 0.22) × 10 -3 . The first and second uncertainties are statistical and systematic, respectively, while the third ones arise from the uncertainty on $\mathscr{B}$(Λ$^+_c$ → p⁢K$^0_S$). The mode Λ$^+_c$ → p⁢K$^0_S$K$^0_S$ is observed for the first time and has a statistical significance of >10σ. The branching fraction of Λ$^+_c$ → p⁢K$^0_S$η has been measured with a threefold improvement in precision over previous results and is found to be consistent with the world average.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS2012

Laser Mode Behavior of the Cassini CIRS Fourier Transform Spectrometer at Saturn

The CIRS Fourier transform spectrometer aboard the NASA/ESA/ASI Cassini orbiter has been acquiring spectra of the Saturnian system since 2004. The CIRS reference interferometer employs a laser diode to trigger the interferogram sampling. Although the control of laser diode drive current and operating temperature are stringent enough to restrict laser wavelength variation to a small fraction of CIRS finest resolution element, the CIRS instrument does need to be restarted every year or two, at which time it may start in a new laser mode. By monitoring the Mylar absorption features in uncalibrated spectra due to the beam splitter Mylar substrate, it can be shown that these jumps are to adjacent modes and that most of the eight-year operation so far is restricted to three adjacent modes. For a given mode, the wavelength stability appears consistent with the stability of the laser diode drive curren.t and operating temperature.

Brasunas, John C.↗
NASA NTRS2011

Fractional Consumption of Liquid Hydrogen and Liquid Oxygen During the Space Shuttle Program

The Space Shuttle uses the propellants, liquid hydrogen and liquid oxygen, to meet part of the propulsion requirements from ground to orbit. The Kennedy Space Center procured over 25 million kilograms of liquid hydrogen and over 250 million kilograms of liquid oxygen during the 3D-year Space Shuttle Program. Because of the cryogenic nature of the propellants, approximately 55% of the total purchased liquid hydrogen and 30% of the total purchased liquid oxygen were used in the Space Shuttle Main Engines. The balance of the propellants were vaporized during operations for various purposes. This paper dissects the total consumption of liqUid hydrogen and liqUid oxygen and determines the fraction attributable to each of the various processing and launch operations that occurred during the entire Space Shuttle Program at the Kennedy Space Center.

Partridge, Jonathan K.↗
NASA NTRS1977

Low cost silicon solar array project silicon materials task: Establishment of the feasibility of a process capable of low-cost, high volume production of silane (step 1) and the pyrolysis of silane to semiconductor-grade silicon (step 2)

Extended operation of a small process-development unit routinely produced high quality silane in 97+% yield from dichlorosilane. The production rate was consistent with design loadings for the fractionating column and for the redistribution reactor. A glass fluid-bed reactor was constructed for room temperature operation. The behavior of a bed of silcon particles was observed as a function of various feedstocks, component configurations, and operating conditions. For operating modes other than spouting, the bed behaved in an erratic and unstable manner. A method was developed for casting molten silicon powder into crack-free solid pellets for process evaluation. The silicon powder was melted and cast into thin walled quartz tubes that sacrificially broke on cooling.

Breneman, W. C.↗
DOE OSTI2024

Recycling polyolefin plastic waste at short contact times via rapid joule heating

Abstract The chemical deconstruction of polyolefins to fuels, lubricants, and waxes offers a promising strategy for mitigating their accumulation in landfills and the environment. Yet, achieving true recyclability of polyolefins into C 2 -C 4 monomers with high yields, low energy demand, and low carbon dioxide emissions under realistic polymer-to-catalyst ratios remains elusive. Here, we demonstrate a single-step electrified approach utilizing Rapid Joule Heating over an H-ZSM-5 catalyst to efficiently deconstruct polyolefin plastic waste into light olefins (C 2 -C 4 ) in milliseconds, with high productivity at much higher polymer-to-catalyst ratio than prior work. The catalyst is essential in producing a narrow distribution of light olefins. Pulsed operation and steam co-feeding enable highly selective deconstruction (product fraction of >90% towards C 2 -C 4 hydrocarbons) with minimal catalyst deactivation compared to Continuous Joule Heating. This laboratory-scale approach demonstrates effective deconstruction of real-life waste materials, resilience to additives and impurities, and versatility for circular polyolefin plastic waste management.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

A sustained high-temperature fusion plasma regime facilitated by fast ions

Nuclear fusion is one of the most attractive alternatives to carbon-dependent energy sources. Harnessing energy from nuclear fusion in a large reactor scale, however, still presents many scientific challenges despite the many years of research and steady advances in magnetic confinement approaches. State-of-the-art magnetic fusion devices cannot yet achieve a sustainable fusion performance, which requires a high temperature above 100 million kelvin and sufficient control of instabilities to ensure steady-state operation on the order of tens of seconds. Here, in this study, we report experiments at the Korea Superconducting Tokamak Advanced Research device producing a plasma fusion regime that satisfies most of the above requirements: thanks to abundant fast ions stabilizing the core plasma turbulence, we generate plasmas at a temperature of 100 million kelvin lasting up to 20 seconds without plasma edge instabilities or impurity accumulation. A low plasma density combined with a moderate input power for operation is key to establishing this regime by preserving a high fraction of fast ions. This regime is rarely subject to disruption and can be sustained reliably even without a sophisticated control, and thus represents a promising path towards commercial fusion reactors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

TRACE Analysis of the STS Target Flow Loop Conceptual Design

This report documents the efforts to model the conceptual design of the STS natural circulation flow loop using TRACE. The results, summarized in Section 2.1, support the conclusion that the conceptual STS natural circulation flow loop design provides sufficient cooling of the tungsten target and exhibits predictable flow behavior, provided that certain design features and/or operating conditions are used. In particular: A sufficient initial liquid volume fraction is required to avoid dryout of the target flow channels; Inclusion of a pressurizer or bellows volume at the top of the loop is recommended and is capable of achieving steady, non-oscillatory flow and temperature conditions at sufficiently high loop pressure. Section 1 provides a detailed description of the geometry and assumptions used in the model, and Section 2 presents the results for the current flow loop design as well as some investigation of potential design modifications with the goal of enhancing the thermal hydraulic stability of the loop.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1978

Sensitivity of 30-cm mercury bombardment ion thruster characteristics to accelerator grid design

The design of ion optics for bombardment thrusters strongly influences overall performance and lifetime. The operation of a 30 cm thruster with accelerator grid open area fractions ranging from 43 to 24 percent, was evaluated and compared with experimental and theoretical results. Ion optics properties measured included the beam current extraction capability, the minimum accelerator grid voltage to prevent backstreaming, ion beamlet diameter as a function of radial position on the grid and accelerator grid hole diameter, and the high energy, high angle ion beam edge location. Discharge chamber properties evaluated were propellant utilization efficiency, minimum discharge power per beam amp, and minimum discharge voltage.

Rawlin, V. K.↗
NASA NTRS1978

Sensitivity of 30-cm mercury bombardment ion thruster characteristics to accelerator grid design

The design of ion optics for bombardment thrusters strongly influences overall performance and lifetime. The operation of a 30-cm thruster with accelerator grid open area fractions ranging from 43 to 24 percent, was evaluated and compared with previously published experimental and theoretical results. Ion optics properties measured included the beam current extraction capability, the minimum accelerator grid voltage to prevent backstreaming, ion beamlet diameter as a function of radial position on the grid and accelerator grid hole diameter, and the high energy, high angle ion beam edge location. Discharge chamber properties evaluated were propellant utilization efficiency, minimum discharge power per beam amp, and minimum discharge voltage.

Rawlin, V. K.↗
NASA NTRS1999

Application of Reconfigurable Avionics for the Bantam Launch Vehicle

The modern aerospace market is placing increasing pressure on launch costs. This is particularly true for small university science payloads, where the cost of the experiment itself is relatively low, and the launch frequency is potentially very high. It is the stated goal of NASA's Bantam Program to reduce dramatically the costs of launching this class of payloads to the order of $1,000,000 per launch for a single 200 pound payload. The envisioned Bantam vehicle is a multi-stage reusable launch system. Meeting the Program's goal for this versatile type of vehicle requires reductions in production cost, maintenance cost, and the operation cost. However, the cost of avionics is a relatively small fraction of the overall cost of launching a payload, and a simple reduction in the avionics costs will not achieve the Bantam goal. Only by reducing weight, volume, and power, while enhancing computational capability can the avionics be used to address the system-level cost reduction requirements.

Wallace, Kevin Shawn↗
NASA NTRS2016

Full Field X-Ray Fluorescence Imaging Using Micro Pore Optics for Planetary Surface Exploration

Many planetary surface processes leave evidence as small features in the sub-millimetre scale. Current planetary X-ray fluorescence spectrometers lack the spatial resolution to analyse such small features as they only provide global analyses of areas greater than 100 mm(exp 2). A micro-XRF spectrometer will be deployed on the NASA Mars 2020 rover to analyse spots as small as 120m. When using its line-scanning capacity combined to perpendicular scanning by the rover arm, elemental maps can be generated. We present a new instrument that provides full-field XRF imaging, alleviating the need for precise positioning and scanning mechanisms. The Mapping X-ray Fluorescence Spectrometer - "Map-X" - will allow elemental imaging with approximately 100μm spatial resolution and simultaneously provide elemental chemistry at the scale where many relict physical, chemical and biological features can be imaged in ancient rocks. The arm-mounted Map-X instrument is placed directly on the surface of an object and held in a fixed position during measurements. A 25x25 mm(exp 2) surface area is uniformly illuminated with X-rays or alpha-particles and gamma-rays. A novel Micro Pore Optic focusses a fraction of the emitted X-ray fluorescence onto a CCD operated at a few frames per second. On board processing allows measuring the energy and coordinates of each X-ray photon collected. Large sets of frames are reduced into 2d histograms used to compute higher level data products such as elemental maps and XRF spectra from selected regions of interest. XRF spectra are processed on the ground to further determine quantitative elemental compositions. The instrument development will be presented with an emphasis on the characterization and modelling of the X-ray focussing Micro Pore Optic. An outlook on possible alternative XRF imaging applications will be discussed.

micro-XRF spectrometer↗
NASA NTRS1991

Transient, hypervelocity flow in an axisymmetric nozzle

The performance of an axisymmetric nozzle was examined which was designed to produce uniform, parallel flow with a nominal Mach number of 8. A free-piston driven shock tube was used to supply the nozzle with high-temperature, high-pressure test gas. Performance was assessed by measuring Pitot pressures across the exit plane of the nozzle and, over the range of operating conditions examined, the nozzle produced satisfactory test flows. However, there were flow disturbances that persisted for significant times after flow initiation. The detailed starting process of the nozzle was also investigated by performing numerical simulations at several nominal test conditions. The classical description of the starting process, based on a quasi-one-dimensional model, provided a reasonable approximation and was used to demonstrate that the starting process could consume a significant fraction of the otherwise usable test gas. This was especially important at high operating enthalpies where nozzle supply conditions were maintained for shorter times. Multidimensional simulations illustrated a mechanism by which the starting process in the actual nozzle could take longer than that predicted by the quasi-one-dimensional analysis. However, the cause of the persistent disturbances observed in the experimental calibration was not identified.

Jacobs, P. A.↗