Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Failure Rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Directed energy deposition of Haynes 282 nickel superalloy

Laser powder directed energy deposition was employed to fabricate Haynes® 282 Ni-based superalloy for high temperature creep testing. Material was heat treated using a single-step aging heat treatment of 800 °C for 4 h. Microstructural analysis was conducted in the as-deposited, solution-annealed, and age-hardened conditions. γ′ precipitates were absent in the as-deposited and annealed condition but formed during aging with an average size of 48.5 ± 12 nm. γ’ denuded zones ranging in thickness from 73 to 469 nm were observed adjacent to an effectively continuous grain boundary carbide film that covered 72.5% of the measured boundary length. The heat-treated material contained a high-volume fraction of TiC carbides ranging in size from 38 to 457 nm. Electron backscatter diffraction showed partial recrystallization, with 77-83% recrystallized area and a heterogeneous grain-size distribution. Creep testing at 750 °C at 300, 320, and 350 MPa revealed significantly inferior performance compared to wrought material, with higher strain rates, earlier tertiary onset, and shorter rupture lives. Fractography shows that failure was dominated by intergranular rupture. Post rupture microstructural analysis results suggest that the creep behavior was primarily governed by the non-equilibrium interface network rather than the bulk γ/γ’ matrix. In conclusion, the findings indicate that achieving wrought-like creep performance necessitates substantial improvements in the additive process, specifically focusing on enhanced homogenization, full recrystallization, and precise control over the morphology and distribution of carbides.

36 - MATERIALS SCIENCE↗
DOE OSTI2020

Unravelling high-temperature stability of lithium-ion battery with lithium-rich oxide cathode in localized high-concentration electrolyte

Lithium (Li)-rich manganese (Mn)-rich oxide (LMR) cathode materials, despite of the high specific capacity up to 250 mAh g-1 suffer from instability of cathode/electrolyte interfacial layer at high working voltages, causing continuous voltage decay and capacity fading, especially at elevated temperatures. In various battery systems, localized high-concentration electrolytes (LHCEs) have been widely reported as a promising candidate to form effective electrode/electrolyte interphases. Here, an optimized LHCE is studied in graphite (Gr)-based full cells being cycled at 25, 45 and 60 °C with the reference of a conventional LiPF6-based electrolyte. It is revealed that the LHCE can effectively suppress continuous electrolyte decompositions and mitigate the dissolution of Mn ions due to the formation of more protective electrode/electrolyte interphases on both anode and cathode, which, in turn, lead to significantly improved cycling stability and enhanced rate capability under the selected temperatures. The mechanistic understanding on the failure of the conventional LiPF6-containing electrolyte and the function of the LHCE in Gr||LMR cells under high temperatures provides valuable perspectives of electrolyte development for practical application of LMR cathodes in high energy density batteries over a wide temperature range.

Localized high-concentration electrolyte, Lithium-↗
DOE OSTI2022

The Natural and Accelerated Evolution of EVA Adhesion Through Intermediate Exposures

Ethylene vinyl acetate (EVA) encapsulants comprise the majority of the encapsulants currently in use; much work has been done to understand and model the adhesive characteristics of EVA-encapsulated modules, but limited work has provided reliable insight into adhesion during the intermediate stages of exposure, limiting the ability to validate model predictions in this range. We provide the adhesion energy measurements for EVA adhesion after nearly six years of field aging and 10 000 h of accelerated aging. Both field and accelerated aging reveal a distinct plateau that emerges during the intermediate exposure periods (after one year in the field and after 1000 h in a chamber). At 10 000 h, adhesion within accelerated aged minimodules falls to a level generally seen after long-term field exposures (>15 years). Previous modeling predicted that adhesion would steadily decrease over the lifetime of a module, but these current results uncover an intermediate plateauing trend that is important to accurately modeling the evolution of adhesion and predicting adhesive failure. Based on these findings, three key model refinements concerning the rate of UV-radical formation and subsequent β-scission, the rate and acceleration of hydrolytic depolymerization, and the profile of the plasticity contribution over time are implemented and discussed.

14 SOLAR ENERGY↗
DOE OSTI2021

Theoretical Analysis and Experimental Validation of Flying-Capacitor Multilevel Converters Under Short-Circuit Fault Conditions

Addressing the increasing demand for high- efficiency and high-power-density converters, the flying-capacitor multilevel converter has shown itself as a promising topology. A key advantage of this topology is the reduced voltage rating of the switches, though also makes it vulnerable to device failure during short-circuit conditions. Despite large interest in fault-tolerant operation of these converters, alongside detailed descriptions of flying capacitor balancing, little research has focused on the converter short-circuit fault analysis, which may cause a switch failure if not properly designed for. Therefore, this work presents a comprehensive model describing the large- signal short-circuit switching behavior of a general N -level flying- capacitor multilevel converter. Highly simplified models used to predict the evolution of the switch current and voltage stress during the fault are proposed, targeted at practicing engineers for conservative design guidelines. These models are used to determine the critical time for remedial action of the converter before reaching some predefined maximum conditions. A 2-to-10- level fully-configurable flying-capacitor multilevel converter and a fault circuit hardware prototype are used to experimentally perform different short-circuit tests that show a good match to the measured behavior.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2022

High-Strain Rate Spall Strength Measurement for CoCrFeMnNi High-Entropy Alloy

In this study, we experimentally investigate the high stain rate and spall behavior of Cantor high-entropy alloy (HEA), CoCrFeMnNi. First, the Hugoniot equations of state (EOS) for the samples are determined using laser-driven CoCrFeMnNi flyers launched into known Lithium Fluoride (LiF) windows. Photon Doppler Velocimetry (PDV) recordings of the velocity profiles find the EOS coefficients using an impedance mismatch technique. Following this set of measurements, laser-driven aluminum flyer plates are accelerated to velocities of 0.5–1.0 km/s using a high-energy pulse laser. Upon impact with CoCrFeMnNi samples, the shock response is found through PDV measurements of the free surface velocities. From this second set of measurements, the spall strength of the alloy is found for pressures up to 5 GPa and strain rates in excess of 106 s−1. Further analysis of the failure mechanisms behind the spallation is conducted using fractography revealing the occurrence of ductile fracture at voids presumed to be caused by chromium oxide deposits created during the manufacturing process.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Self-adaptive weights based on balanced residual decay rate for physics-informed neural networks and deep operator networks

Physics-informed deep learning has emerged as a promising alternative for solving partial differential equations. However, for complex problems, training these networks can still be challenging, often resulting in unsatisfactory accuracy and efficiency. In this work, we demonstrate that the failure of plain physics-informed neural networks arises from the significant discrepancy in the convergence rate of residuals at different training points, where the slowest convergence rate dominates the overall solution convergence. Based on these observations, we propose a pointwise adaptive weighting method that balances the residual decay rate across different training points. The performance of our proposed adaptive weighting method is compared with current state-of-the-art adaptive weighting methods on benchmark problems for both physics-informed neural networks and physics-informed deep operator networks. In conclusion, through extensive numerical results we demonstrate that our proposed approach of balanced residual decay rates offers several advantages, including bounded weights, high prediction accuracy, fast convergence rate, low training uncertainty, low computational cost, and ease of hyperparameter tuning.

Balanced convergence rate↗
DOE OSTI2025

Electrochemical-Mechanical Coupling Strongly Affects the Performance of Nanopore, Thin-Film, and Solid-State Batteries

Here, the present study focuses on the electrochemical-mechanical (ECM) coupling effects of a thin-film, solid-state battery with only stiff, ceramic materials, in contrast to prior investigations that focus on individual active material particles or aggregations of particles. We model the impacts of ECM couplings including stress-transport and stress-equilibrium potential on the full-cell performance and potential mechanical failure modes of a thin-film battery conformally deposited in a nanopore scaffold, which is an experimentally achievable device. Model results indicate electrode volume changes due to lithium insertion or removal, along with mechanical boundary conditions, result in stress gradients that alter the lithium-ion flux, reduce lithium concentration gradients, and improve cell rate capability. However, the high stress levels in the cell can also lead to mechanics-related failure such as the separation of cell layers. For the parameter set in this work, stress-transport coupling has a much greater influence on rate capability than stress-potential coupling. Optimization of thin-film batteries to harness the benefits of ECM coupling effects requires leveraging geometric design and material selection. The current work underscores the need for further theoretical and experimental investigation into ECM coupling effects in thin-film batteries to enhance their understanding and design optimization.

25 ENERGY STORAGE↗
DOE OSTI2020

Dynamic Tensile Characterization of Thin-Sheet Brittle Metallic Materials

Refractory metals are favorable materials in applications where high strength and ductility are needed at elevated temperatures. In some cases, operating temperatures may be near the melting point of the material. However, as temperature drops, refractory metals typically undergo a significant mechanical response change - ductile-to-brittle transition. These materials may be subjected to high strain rate loading at an ambient temperature state, such as an impact or crash. Knowledge of the high rate material properties are essential for design as well as simulation of impact events. The high rate stress-strain behavior of brittle metallic materials at ambient temperature is rarely studied because of experimental challenges, particularly when failure is involved. Failure typically occurs within the non-gage section of the material, which invalidates any collected stress-strain information. Here, a method to determine a specimen geometry which will produce failures in the gage section is presented. Pure tungsten in thin-sheet form was used as a trial material to select a specimen geometry for high rate Kolsky tension bar experiments. A finite element simulation was conducted to derive a strain correction for more accurate results. The room temperature stress-strain behavior of pure tungsten at a strain rate of 24 s –1 is presented. The outcome of this experimental technique can be applied to other brittle materials for dynamic tensile characterization.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Elucidating size effects on the yield strength of single-crystal Cu via the Richtmyer–Meshkov instability

Capturing the dynamic response of a material under high strain-rate deformation often demands challenging and time consuming experimental effort. While shock hydrodynamic simulation methods can aid in this area, a priori characterizations of the material strength under shock loading and spall failure are needed in order to parameterize constitutive models needed for these computational tools. Moreover, parameterizations of strain-rate-dependent strength models are needed to capture the full suite of Richtmyer–Meshkov instability (RMI) behavior of shock compressed metals, creating an unrealistic demand for these training data solely on experiments. Herein, we sweep a large range of geometric, crystallographic, and shock conditions within molecular dynamics (MD) simulations and demonstrate the breadth of RMI in Cu that can be captured from the atomic scale. In this work, yield strength measurements from jetted and arrested material from a sinusoidal surface perturbation were quantified as Y RMI = 0.787 ± 0.374 GPa, higher than strain-rate-independent models used in experimentally matched hydrodynamic simulations. Defect-free, single-crystal Cu samples used in MD will overestimate Y RMI , but the drastic scale difference between experiment and MD is highlighted by high confidence neighborhood clustering predictions of RMI characterizations, yielding incorrect classifications.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Scaling up carboxylic acid production from cheese whey and brewery wastewater via methane-arrested anaerobic digestion

In a circular economy, organic waste streams are valuable resources for sustainably producing chemicals and fuels. This study investigates a new methane-arrested anaerobic digestion (MAAD) process that converts high-strength cheese whey and brewery wastewater into carboxylic acids. The process was developed and optimized under various bench-scale semi-continuous (fed-batch) operating conditions (e.g., retention time, organic loading rate, pH, and feed/harvest frequency). The MAAD responses to various control-failure scenarios were also systematically investigated. The highest total acid productivity was 26g/(L liq ·d) with a substrate conversion of 0.79g COD digested /g COD fed at a hydraulic retention time (HRT) of approximately 2 d in a 14-L digester. The most stable conditions for digester operation (HRT 3 d at pH 6.0 and 40°C) were selected for process scale-up to 100gal (~380 L). Semi-continuous, pilot-scale MAAD successfully produced a total acid concentration of 40.6+/-1.1 g/L with 8.1% acetic acid, 45.1% butyric acid, and 44.5% lactic acid. The links between wastewater characteristics, operation mode, digester scale, and microbial community structure were statistically analyzed. The results show genera Sporolactobacillus and Clostridium positively correlate with butyric acid production (Pearson correlation coefficient>0.5). Moreover, four kinetic models were developed and fit to batch MAAD experimental datasets (R 2 >95%) and were successfully applied to predict the total acid production in both bench-and pilot-scale semi-continuous MAADs. In conclusion, this study shows MAAD has the potential for industrial-scale applications and is a robust platform to valorize low- or negative-value waste streams into high-value bioproducts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

ORNL Input to GDSA Repository Systems Analysis FY21

This document satisfies the M3 milestone M3SF-21OR010304082 titled “ORNL Input to GDSA Repository Systems.” This document describes the current status of Oak Ridge National Laboratory’s (ORNL’s) efforts related to analyses of dual-purpose canister (DPC) disposal in unsaturated alluvium with a focus on thermal hydrological constraints on criticality timing and power output. This analysis updates previous analyses of thermal hydrological constraints on timing and power output of a potential criticality event in Dual-Purpose Canisters (DPCs) in a hypothetical repository in unsaturated alluvium using a more realistic representation of heat transport inside dry DPCs. PFLOTRAN was used for the simulations of multiphase thermal hydrology near a single DPC. The scenario considers a DPC failure at 9000 years, allowing water to enter and eventually fill the DPC. Once the DPC is filled to a level that could support a criticality event, different values for criticality power output were added to the decay heat. The main objective is to bound the power output that could be produced by a criticality event without driving water out of the package. For the conditions analyzed here, following a package breach, the alluvial formation could supply enough water to allow enough accumulation in the DPC to support a criticality event. However, the power output that would be generated is limited to modest values by loss of water moderator due to evaporation and vapor diffusion. In the reference case scenario, the DPC would not start to fill with water until about 16,000 years post closure and would not fill to a level that allows a criticality event until approximately 25,000 years post closure. The long-term average power output that could be sustained without driving off the water and terminating the criticality event is limited to approximately 100 W. Sensitivity to assumed conditions and parameters in the reference case, especially the deep percolation rate, need to be addressed but could not be undertaken because of numerical failures of the PFLOTRAN code running in general mode in the dry conditions of an unsaturated alluvium repository

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Resilience Design Patterns: A Structured Approach to Resilience at Extreme Scale (V.2.0)

Reliability is a serious concern for future extreme-scale high-performance computing (HPC) systems. Projections based on the current generation of HPC systems and technology roadmaps suggest the prevalence of very high fault rates in future systems. The errors resulting from these faults will propagate and generate various kinds of failures, which may result in outcomes ranging from result corruptions to catastrophic application crashes. Therefore, the resilience challenge for extreme-scale HPC systems requires coordination between various hardware and software technologies that are capable of handling a broad set of fault models at accelerated fault rates. Also, due to practical limits on power consumption in future HPC systems, they are likely to embrace innovative architectures, increasing the levels of hardware and software complexities. Therefore, the techniques that seek to improve resilience must navigate the complex trade-off space between resilience and the overheads to power consumption and performance. While the HPC community has developed various resilience solutions, application-level techniques as well as system-based solutions, the solution space of HPC resilience techniques remains fragmented. There are no formal methods to integrate the various HPC resilience techniques into composite solutions, nor are there methods to holistically evaluate the adequacy and efficacy of such solutions in terms of their protection coverage, and their performance & power efficiency characteristics. Additionally, few implementations of current resilience solutions are portable to newer architectures and software environments that will be deployed on future systems. We developed a new structured approach to the management of HPC resilience using the concept of resilience-based design patterns. In general, a design pattern is a repeatable solution to a commonly occurring problem. We identified the well-known solutions that are commonly used to deal with faults, errors and failures in HPC systems. In the initial design patterns specification (version 1.0), we described the various solutions, which address specific problems in the design of resilient HPC environments, in the form of patterns. Each pattern describes a problem caused by a fault, error or failure event in an HPC environment, and then describes the core of the solution of the problem in such a way that this solution may be adapted to different systems and implemented at different layers of the system stack. The catalog of these resilience design patterns provides designers with a collection of design elements. To construct complete resilience solutions using combinations of various patterns, we defined a framework that enhances HPC designers' understanding of the important constraints and the opportunities for the design patterns to be implemented and deployed at various layers of the system stack. The design framework is also useful for establishing interfaces and mechanisms to coordinate flexible fault management across hardware and software components, as well as to consider the trade-off between performance, resilience, and power consumption when constructing a solution. The resilience design patterns specification version 1.1 included more detailed explanations of the pattern solutions, the context in which the patterns are applicable, and the implications for hardware or software design. It also provided several additional examples and detailed case studies to demonstrate the use of patterns to build realistic solutions. In version 1.2 of the specification document, we have improved the pattern descriptions, including graphical representations of the pattern components. These improvements are largely based on critical comments, feedback and suggestions received from pattern experts and readers of the previous versions of the specification. The pattern classification has been modified to further clarify the relationships between pattern categories. This version of the specification also introduces a pattern language for resilience design patterns. The pattern language presents the patterns in the catalog as a network, revealing the relations among the resilience patterns. The language provides designers with the means to explore alternative techniques for handling a specific fault model that may have different efficiency and complexity characteristics. Using the pattern language also enables the design and implementation of comprehensive resilience solutions as a set of interconnected resilience patterns that can be instantiated across layers of the system stack. The overall goal of this work is to provide hardware and software designers, as well as the users and operators of HPC systems, a systematic methodology for the design and evaluation of resilience technologies in HPC systems that keep scientific applications running to a correct solution in a timely and cost-efficient manner despite frequent faults, errors, and failures of various types. Version 2.0 expands the resilience design pattern classification and catalog to include self-stabilization patterns and reliability, availability and performance models for each structural pattern.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Physics informed neural network can retrieve rate and state friction parameters from acoustic monitoring of laboratory stick-slip experiments

Various machine learning (ML) and deep learning (DL) techniques have been recently applied to the forecasting of laboratory earthquakes from friction experiments. The magnitude and timing of shear failures in stick-slip cycles are predicted using features extracted from the recorded ultrasonic or acoustic emission (AE) signals. In addition, the Rate and State Friction (RSF) constitutive laws are extensively used to model the frictional behavior of faults. In this work, we use data from shear experiments coupled with passive acoustic (variance, kurtosis, and AE rate) interleaved with active source ultrasonic monitoring (transmitted wave amplitude) to develop physics-informed neural network (PINN) models incorporating the RSF law and AE rate generation equation with wave amplitude serving as a proxy for friction state variable. This PINN framework allows learning RSF parameters from stick-slip experiments rather than measuring them through a series of velocity step experiments. We observe that when the stick-slip cycles are irregular, the PINN models outperform the data-driven DL models. Transfer learning (TL) PINN models are also developed by pre-training on data collected at one normal stress level followed by forecasting shear failures and retrieving RSF parameters at other stress levels (i.e., with different recurrence intervals) after retraining on a limited amount of new data. Our findings suggest that TL models perform better compared to standalone models. Both standalone and TL PINN-estimated RSF parameters and their ground truth values show excellent agreements thus demonstrating that RSF parameters can be retrieved from laboratory stick-slip experiments using the corresponding acoustic data and that the transmitted wave amplitude provides a good representation of the evolving frictional state during stick-slips.

58 GEOSCIENCES↗
DOE OSTI2021

Optimizing Treatment in Intermediate-Risk Prostate Cancer: Secondary Analysis of a Randomized Phase 3 Trial

To identify patients with intermediate-risk prostate cancer (IRPC) benefiting from de-escalation of androgen deprivation therapy (ADT) and/or dose escalated radiation therapy (DERT), we performed a secondary analysis of a phase 3 trial by measuring biochemical failure (BF), distant metastases, prostate cancer–specific mortality, overall survival (OS), and distant metastases-free survival (DMFS) rates according to prognostic intermediate risk factors (IRF).

62 RADIOLOGY AND NUCLEAR MEDICINE↗
DOE OSTI2022

Role of tilt grain boundaries on the structural integrity of WSe 2 monolayers

Transition metal dichalcogenides (TMDCs) are potential materials for future optoelectronic devices. Grain boundaries (GBs) can significantly influence the optoelectronic properties of TMDC materials. Here, we have investigated the mechanical characteristics of tungsten diselenide (WSe 2 ) monolayers and failure process with symmetric tilt GBs using ReaxFF molecular dynamics simulations. In particular, the effects of topological defects, loading rates, and temperatures are investigated. We considered nine different grain boundary structures of monolayer WSe 2 , of which six are armchair (AC) tilt structures, and the remaining three are zigzag (ZZ) tilt structures. Our results indicate that both tensile strength and fracture strain of WSe 2 with symmetric tilt GBs decrease as the temperature increases. We revealed an interfacial phase transition for high-angle GBs reduces the elastic strain energy within the interface at finite temperatures. Furthermore, brittle cracking is the dominant failure mode in the WSe 2 monolayer with tilted GBs. WSe 2 GB structures showed more strain rate sensitivity at high temperatures than at low temperatures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Electrolyte and Cutoff Potential Effects on Cycle Life of Li4Ti5O12/LiNi0.9Mn0.1O2 Batteries for Behind-the-Meter Storage Applications

Behind-the-Meter Storage (BTMS) is a stationary battery energy storage system that is connected to the electrical distribution system on the customer's side of the utility's service meter. BTMS systems are used to store electrical energy from the grid as well as inconstant, renewable energy, such as local solar and wind generation. A successful BTMS system will allow the customer to pair their energy generation and storage to optimize electrical consumption from the grid, improving reliability and minimizing cost. For BTMS applications, batteries must be designed and optimized with different set of criteria from other leading segments of the Li-ion battery market, like transportation, due the system being stationary and proximal to the residential or commercial building it's benefitting. BTMS applications prioritize safety, cost (low/no-critical materials), reliability (20-year calendar life), and durability (10,000 cycle life), while having the ability to (minimally) compromise energy density and rate capability. Lithium titanate (Li4Ti5O12-, LTO) is a promising anode candidate for BTMS applications due to its high safety and capacity retention, while maintaining a reasonable 160 mAhg-1 reversable capacity and composition of relatively abundant materials. (1) Specifically, LTO has a high working voltage which helps to prevent Li dendrite formation, improving safety. Furthermore, LTO also has negligible lithiation-based volume change, leading to less mechanical pulverization, or loss of active material, upon cycling. For the cathode, materials with little or no Co are of high interest due to the high cost and low abundance of Co. LiMn2O4 (LMO) has been paired with LTO for BTMS applications in the past due to its safety, low cost (abundancy), and reasonably high operating voltage. (2-4) However, the low capacity of LMO limits energy density and specific energy. While not the highest priority for BTMS applications, increasing energy density will enable deployment in space constrained BTMS applications and decrease total cost. LiNi0.9Mn0.1O2 (LN-MO) is a recently developed material with promise due to its high operating voltage and relatively low price. (5) However, Ni-rich layered oxides, including LNMO, tend to struggle with capacity retention during high-voltage cycling due to mechanical pulverization, irreversible phase transitions, and unstable solid-electrolyte interphase. The study presented here focuses on building an understanding of how electrolyte solvent and varied cutoff potentials will impact the cycle life of LTO/LN-MO cells. Specifically, a comparison is provided between ethylene carbonate (EC), ethyl methyl carbonate (EMC), fluoroethylene carbonate (FEC), and Gen2 electrolyte solvents with 1M Lithium hexafluorophosphate (LiPF6) salt, cycling to two upper termination potentials, 2.6V and 2.7V. Electrochemical testing and diagnostics (e.g., differential capacity analysis, area specific impedance, constant voltage hold, and rate capability) and post-mortem characterization will be used to understand the aging behavior and failure mechanisms of the 8 cell combinations (four electrolytes and two voltage cutoffs). Cells with FEC electrolyte showed a lower initial capacity compared to cells with Gen2, EMC, and EC cycling at both voltages; however, the cells with FEC showed consistent trends in capacity retention with 2.6V and 2.7V termination potentials, while the cells with the other electrolytes showed much higher rates of capacity loss when cycling to the higher voltage. These results indicate that FEC may play a role in improving durability of high-voltage, Ni-rich electrode systems for use in high-cycle applications, such as BTMS.

electrolyte↗
DOE OSTI2020

Acoustic Energy Release During the Laboratory Seismic Cycle: Insights on Laboratory Earthquake Precursors and Prediction

Abstract Machine learning can predict the timing and magnitude of laboratory earthquakes using statistics of acoustic emissions. The evolution of acoustic energy is critical for lab earthquake prediction; however, the connections between acoustic energy and fault zone processes leading to failure are poorly understood. Here, we document in detail the temporal evolution of acoustic energy during the laboratory seismic cycle. We report on friction experiments for a range of shearing velocities, normal stresses, and granular particle sizes. Acoustic emission data are recorded continuously throughout shear using broadband piezo‐ceramic sensors. The coseismic acoustic energy release scales directly with stress drop and is consistent with concepts of frictional contact mechanics and time‐dependent fault healing. Experiments conducted with larger grains (10.5 μm) show that the temporal evolution of acoustic energy scales directly with fault slip rate. In particular, the acoustic energy is low when the fault is locked and increases to a maximum during coseismic failure. Data from traditional slide‐hold‐slide friction tests confirm that acoustic energy release is closely linked to fault slip rate. Furthermore, variations in the true contact area of fault zone particles play a key role in the generation of acoustic energy. Our data show that acoustic radiation is related primarily to breaking/sliding of frictional contact junctions, which suggests that machine learning‐based laboratory earthquake prediction derives from frictional weakening processes that begin very early in the seismic cycle and well before macroscopic failure.

58 GEOSCIENCES↗
DOE OSTI2023

Effects of wind field characteristics on pitch bearing reliability: a case study of 5 MW reference wind turbine at onshore and offshore sites; Auswirkungen von Windfeldeigenschaften auf die Zuverlässigkeit von Rotorblattlagern: eine Fallstudie über eine 5-MW-Referenz-Windkraftanlage an Onshore- und Offshore-Standorten

This paper presents a study on pitch bearing basic rating life affected by wind field characteristics at both onshore and offshore wind sites. The National Renewable Energy Laboratory 5 MW reference wind turbine is selected for the study. Wind field characteristics including reference hub height mean wind speed, wind speed distribution, wind shear, and vertical inflow are studied. A decoupled approach is employed where global analysis is performed first. Second, the load effects from the global analysis are applied on a reference pitch bearing designed based on best industrial practices. For the case study onshore site, it is found that the Kernel density estimation best fits the wind distribution, while the International Electrotechnical Commission proposed distribution appears to be not suitable. Moreover, it is shown that the seed number has high effect on the bearing life in turbulence wind and the wind speeds around rated have the highest contribution in both bearing fatigue damage and extreme load failure. The results contribute to better understanding of the wind field characteristics on the pitch bearing life.

17 WIND ENERGY↗