Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FLAME”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Autoignited laminar lifted flames of methane, ethylene, ethane, and n-butane jets in coflow air with elevated temperature

The autoignition characteristics of laminar lifted flames of methane, ethylene, ethane, and n-butane fuels have been investigated experimentally in coflow air with elevated temperature over 800 K. The lifted flames were categorized into three regimes depending on the initial temperature and fuel mole fraction: (1) non-autoignited lifted flame, (2) autoignited lifted flame with tribrachial (or triple) edge, and (3) autoignited lifted flame with mild combustion. For the non-autoignited lifted flames at relatively low temperature, the existence of lifted flame depended on the Schmidt number of fuel, such that only the fuels with Sc > 1 exhibited stationary lifted flames. The balance mechanism between the propagation speed of tribrachial flame and local flow velocity stabilized the lifted flames. At relatively high initial temperatures, either autoignited lifted flames having tribrachial edge or autoignited lifted flames with mild combustion existed regardless of the Schmidt number of fuel. The adiabatic ignition delay time played a crucial role for the stabilization of autoignited flames. Especially, heat loss during the ignition process should be accounted for, such that the characteristic convection time, defined by the autoignition height divided by jet velocity was correlated well with the square of the adiabatic ignition delay time for the critical autoignition conditions. The liftoff height was also correlated well with the square of the adiabatic ignition delay time. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Local consumption speed of turbulent premixed flames - An analysis of ''memory effects''

The local turbulent flame speed of an attached flame is not only a function of the local flow and flame conditions, but also of upstream conditions - i.e., it is ''non-local'' or exhibits ''memory''. Non-locality adds an additional degree of freedom to the classic problem of a freely propagating flame propagating normally to the time averaged flow. Non-locality occurs due to mean tangential flow along the flame brush, which causes flame wrinkles to translate downstream. As such, the wrinkling of the flame at any given point is not only a function of the local velocity disturbance, but also a superposition of flame surface perturbations from locations upstream at previous times. This causes the correlation length scale of turbulent flame wrinkles to differ from that of the underlying turbulent velocity fluctuations. The objective of this paper is to provide a physical description of the key flame kinematic processes that cause these non-local effects. Two approaches are adopted in this work. First, analytical solutions of the G-equation that explicitly describe the effect of non-locality in the low turbulence limit are developed. Second, numerical computations of the G-equation are performed that demonstrate the role of non-linearity in flame surface kinematics at higher turbulence intensities. Finally, these predictions are shown to be consistent with data from a turbulent Bunsen flame. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DISTRIBUTED FLAMES IN TYPE Ia SUPERNOVAE

At a density near a few x10{sup 7} g cm{sup -3}, the subsonic burning in a Type Ia supernova (SN) enters the distributed regime (high Karlovitz number). In this regime, turbulence disrupts the internal structure of the flame, and so the idea of laminar burning propagated by conduction is no longer valid. The nature of the burning in this distributed regime depends on the turbulent Damkoehler number (Da{sub T}), which steadily declines from much greater than one to less than one as the density decreases to a few x10{sup 6} g cm{sup -3}. Classical scaling arguments predict that the turbulent flame speed s{sub T} , normalized by the turbulent intensity u-check, follows s{sub T}/u-check = Da{sub T}{sup 1/2} for Da{sub T} {approx}< 1. The flame in this regime is a single turbulently broadened structure that moves at a steady speed, and has a width larger than the {integral} scale of the turbulence. The scaling is predicted to break down at Da{sub T} {approx} 1, and the flame burns as a turbulently broadened effective unity Lewis number flame. This flame burns locally with speed s{sub l}ambda and width l{sub l}ambda, and we refer to this kind of flame as a lambda-flame. The burning becomes a collection of lambda-flames spread over a region approximately the size of the {integral} scale. While the total burning rate continues to have a well-defined average, s{sub T}{approx}u-check, the burning is unsteady. We present a theoretical framework, supported by both one-dimensional and three-dimensional numerical simulations, for the burning in these two regimes. Our results indicate that the average value of s{sub T} can actually be roughly twice u-check for Da{sub T} {approx}> 1, and that localized excursions to as much as 5 times u-check can occur. We also explore the properties of the individual flames, which could be sites for a transition to detonation when Da{sub T} {approx} 1. The lambda-flame speed and width can be predicted based on the turbulence in the star (specifically the energy dissipation rate epsilon*) and the turbulent nuclear burning timescale of the fuel tau {sup T}{sub nuc}. We propose a practical method for measuring s{sub l}ambda and l{sub l}ambda based on the scaling relations and small-scale computationally inexpensive simulations. This suggests that a simple turbulent flame model can be easily constructed suitable for large-scale distributed SNe flames. These results will be useful both for characterizing the deflagration speed in larger full-star simulations, where the flame cannot be resolved, and for predicting when detonation occurs.

79 ASTRONOMY AND ASTROPHYSICS↗

Predictive LES Modeling and Validation of High-Pressure Turbulent Flames and Flashback in Hydrogen-enriched Gas Turbines

The overall objective of this project is to make advances in large-eddy simulation modeling of swirl-flame flashback at elevated pressure, where the reactants can be premixed or stratified, and composed of methane enriched with hydrogen. The modeling effort was conducted with a companion experimental validation effort that focused on high-speed measurements of flashback in a model swirl-flame combustor. The modeling effort focused on the development of manifold-based combustion model for flashback simulations. The main complexity in this configuration comes from the flames’ propagation through a stratified fuel-air mixture along with heat loss near the walls. For this purpose, a non-adiabatic flamelet model was developed and tested using canonical flow configurations. Further, extensive validation in premixed configurations is used to establish the model’s accuracy in capturing heat loss and flame propagation. Finally, the model was tested using the UT flame flashback experiment, and was shown to accurately capture the flame flashback process. The end products from this work are a) a full validated flameout-based approach for modeling flame flashback; b) a complete implementation of the model in the open source OpenFOAM framework, which has been made available to both industry and academia; c) an extensive suite of validation studies performed using the OpenFOAM solver. In addition, new techniques for flame modeling, subfilter modeling of scalars, and simulation of low Mach number flows were developed and tested. In the experimental validation effort, flashback was studied in a premixed and stratified swirl flame by using high-speed imaging diagnostics. Fuels tested included CH 4 enriched with H 2 , with H 2 enrichment up to 84% by volume. These flashback experiments are conducted at pressures ranging from 1 to 5 atm. A swirler-based fuel-injection system was used to create the fuel-air stratification in the radial direction. For the high-pressure measurements, an optically accessible elevated pressure chamber was used. The spatial distribution of the equivalence ratio under non-reacting conditions was characterized using planar laser-induced fluorescence with acetone as the fuel tracer. It was observed that fuel-air pockets were distributed across the mixing tube width, although in an average sense, the fuel-air mixture was radially stratified. The global behavior of upstream flame propagation was investigated for different levels of hydrogen-enrichment. For stratified hydrogen-rich flashback, the propagation path of the flame changed from the inner wall to outer wall, which was induced by the faster chemistry of stoichiometric mixtures that are frequently present near the outer wall. This behavior of hydrogen-rich flashback persists even at elevated pressures up to 5 atm, although the propagation of the flame occurs as a wide flame tongue as opposed to the acute-tipped flame structures present in the atmospheric cases. The end product of the experimental effort is greatly improved knowledge of flashback physics and a unique database that can be used for model validation.

08 HYDROGEN↗

Sensitivity Studies of Premixed Flame Response to Transverse, High Frequency Disturbances

This study analyzes the response of premixed flames to high frequency transverse acoustic disturbances. A significant body of experiment, modeling and simulation efforts has been performed to understand the response of the spatially integrated heat release of premixed flames to low-frequency disturbances. These studies quantified this sensitivity through the Flame Transfer Function (FTF), as the global heat release is the key quantity influencing thermoacoustic stability for acoustically compact flames. Recent efforts have expanded these models to consider high-frequency acoustic disturbances, and the sensitivity of premixed flames through the Rayleigh integral (RI). The full Rayleigh Integral, as opposed to simply the spatially integrated heat release, must be considered in these cases where the flame is not acoustically compact. Prior modeling studies considered several effects - stability of axisymmetric flames centered in a cylindrical combustion chamber and the effect of flame offset from the combustor axis and the effect of mean flame asymmetries in the flame centered in the combustor. These studies showed that the flame's stability was sensitive to all these parameters, as well as to the transverse mode in question. In this paper, we quantify these different parametric sensitivities of premixed flame stability in the presence of high-frequency transverse acoustic modes - specifically sensitivity to flame length and nozzle location within the acoustic mode shape for 2 different transverse modes. The sensitivity of the RI to these control parameters provides an improved understanding of which flame parameters are critical to improve the overall thermoacoustic stability of the system.

Acharya, Vishal S.↗

A numerical study of transient ignition and flame characteristics of diluted hydrogen versus heated air in counterflow.

Combined experimental and numerical studies of the transient response of ignition to strained flows require a well-characterized ignition trigger. Laser deposition of a small radical pool provides a reliable method for initiating ignition of mixtures that are near the ignition limit. Two-dimensional direct numerical simulations are used to quantify the sensitivity of ignition kernel formation and subsequent edge-flame propagation to the oxidizer temperature and the initial width and amplitude of O-atom deposition used to trigger ignition in an axisymmetric counterflow of heated air versus ambient hydrogen/nitrogen. The ignition delay and super-equilibrium OH concentration in the nascent ignition kernel are highly sensitive to variations in these initial conditions. The ignition delay decreases as the amplitude of the initial O-atom deposition increases. The spatial distribution and the magnitude of the OH overshoot are governed by multi-dimensional effects. The degree of OH overshoot near the burner centerline increases as the diameter of the initial O-atom deposition region decreases. This result is attributed to preferential diffusion of hydrogen in the highly curved leading portion of the edge flame that is established following thermal runaway. The edge-flame speed and OH overshoot at the leading edge of the edge flame are relatively insensitive to variations in the initial conditions of the ignition. The steady edge-flame speed is approximately twice the corresponding laminar flame speed. The rate at which the edge flame approaches its steady state is insensitive to the initial conditions and depends solely on the diffusion time scale at the edge flame. The edge flame is curved toward the heated oxidizer stream as a result of differences in the chemical kinetics between the leading edge and the trailing diffusion flame. The structure of the highly diluted diffusion flame considered in this study corresponds to Linan's 'premixed flame regime' in which only the oxidizer leaks through the reaction zone such that the flame is located at fuel lean rather than stoichiometric mixture fraction conditions.

08 HYDROGEN↗

Understanding and predicting soot generation in turbulent non-premixed jet flames.

This report documents the results of a project funded by DoD's Strategic Environmental Research and Development Program (SERDP) on the science behind development of predictive models for soot emission from gas turbine engines. Measurements of soot formation were performed in laminar flat premixed flames and turbulent non-premixed jet flames at 1 atm pressure and in turbulent liquid spray flames under representative conditions for takeoff in a gas turbine engine. The laminar flames and open jet flames used both ethylene and a prevaporized JP-8 surrogate fuel composed of n-dodecane and m-xylene. The pressurized turbulent jet flame measurements used the JP-8 surrogate fuel and compared its combustion and sooting characteristics to a world-average JP-8 fuel sample. The pressurized jet flame measurements demonstrated that the surrogate was representative of JP-8, with a somewhat higher tendency to soot formation. The premixed flame measurements revealed that flame temperature has a strong impact on the rate of soot nucleation and particle coagulation, but little sensitivity in the overall trends was found with different fuels. An extensive array of non-intrusive optical and laser-based measurements was performed in turbulent non-premixed jet flames established on specially designed piloted burners. Soot concentration data was collected throughout the flames, together with instantaneous images showing the relationship between soot and the OH radical and soot and PAH. A detailed chemical kinetic mechanism for ethylene combustion, including fuel-rich chemistry and benzene formation steps, was compiled, validated, and reduced. The reduced ethylene mechanism was incorporated into a high-fidelity LES code, together with a moment-based soot model and models for thermal radiation, to evaluate the ability of the chemistry and soot models to predict soot formation in the jet diffusion flame. The LES results highlight the importance of including an optically-thick radiation model to accurately predict gas temperatures and thus soot formation rates. When including such a radiation model, the LES model predicts mean soot concentrations within 30% in the ethylene jet flame.

33 ADVANCED PROPULSION SYSTEMS↗

Flame propagation enhancement by plasma excitation of oxygen. Part I: Effects of O{sub 3}

The thermal and kinetic effects of O{sub 3} on flame propagation were investigated experimentally and numerically by using C{sub 3}H{sub 8}/O{sub 2}/N{sub 2} laminar lifted flames. Ozone produced by a dielectric barrier plasma discharge was isolated and measured quantitatively by using absorption spectroscopy. Significant kinetic enhancement by O{sub 3} was observed by comparing flame stabilization locations with and without O{sub 3} production. Experiments at atmospheric pressures showed an 8% enhancement in the flame propagation speed for 1260 ppm of O{sub 3} addition to the O{sub 2}/N{sub 2} oxidizer. Numerical simulations showed that the O{sub 3} decomposition and reaction with H early in the pre-heat zone of the flame produced O and OH, respectively, from which the O reacted rapidly with C{sub 3}H{sub 8} and produced additional OH. The subsequent reaction of OH with the fuel and fuel fragments, such as CH{sub 2}O, provided chemical heat release at lower temperatures to enhance the flame propagation speed. It was shown that the kinetic effect on flame propagation enhancement by O{sub 3} reaching the pre-heat zone of the flame for early oxidation of fuel was much greater than that by the thermal effect from the energy contained within O{sub 3}. For non-premixed laminar lifted flames, the kinetic enhancement by O{sub 3} also induced changes to the hydrodynamics at the flame front which provided additional enhancement of the flame propagation speed. The present results will have a direct impact on the development of detailed plasma-flame kinetic mechanisms and provided a foundation for the study of combustion enhancement by O{sub 2}(a{sup 1}{delta}{sub g}) in part II of this investigation. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The composition of gases from a diffusion flame above longleaf pine needle fuel beds

The gas and tar composition of a diffusion flame from longleaf pine needles is currently poorly understood and more data are needed to fill in the gap between pyrolysis data and smoke plume data, thus improving physical and chemical modeling of wildland smoke formation. A pilot experiment to measure light gas and tar composition of such a flame is described for three flame regions: persistent flame (flame base), intermittent flame, and smoke plume. Flame gases from 24 experimental fires were collected in canisters and analyzed using EPA method TO-14A for CO 2 , CO, H 2 , CH 4 , and C 2 to C 7 hydrocarbon gases. Condensed gas (tar) samples were collected and analyzed using GC/MS. Other light gases were measured using FTIR spectroscopy. Results from compositional data analysis suggest significant differences in (relative) concentration of compounds detected in the three regions of the flame. Statistical tests for differences in flame zones were performed using the canister data: Concentration of hydrocarbons relative to CO and CO 2 decreased from the persistent flame zone above the pyrolyzing needles through the intermittent flame region into the flame-free plume. This was likely due to both chemical reactions (oxidation) occurring in the flame as well as the introduction of air into the flame/plume by entrainment.

Biomass↗

Chapman–Jouguet deflagration criteria and compressibility dynamics of turbulent fast flames for turbulence-induced deflagration-to-detonation transition

This work characterizes the compressibility dynamics in turbulent fast flames for a range of turbulent flame speeds. These turbulent fast flames experience increased effects of compressibility through the formation of strong shocks and may develop a runaway acceleration combined with a pressure buildup that leads to turbulence induced deflagration-to-detonation transition (tDDT). Simultaneous high-speed particle image velocimetry, OH* chemiluminescence, schlieren, and pressure measurements are used to examine the reacting flow field and flame dynamics. We examine flames with turbulent flame speeds ranging from 100 to 600 m/s. At lower turbulent flame speeds, the flame is not able to produce favorable background conditions for deflagration-to-detonation transition (DDT) onset, and thus flame compressibility and turbulence amplification are less dominant, resulting in a weaker acoustic coupling between the flame and compressed region. As the turbulent burning velocities exceed the Chapman–Jouguet deflagration speed, favorable background conditions are produced, as we observe flame-generated shocks and flame-generated turbulence with higher turbulent velocities and larger turbulent scales. At this regime, the flame is categorized to be at the runaway transition regime that leads to tDDT.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Experimental annular stratified flames characterisation stabilised by weak swirl

A burner for the investigation of lean stratified premixed flames propagating in intense isotropic turbulence has been developed. Lean pre-mixtures of methane at different equivalence ratios were divided between two concentric co-flows to obtain annular stratification. Turbulence generators were used to control the level of turbulence intensity in the oncoming flow. A third annular weakly swirling airflow provided the flame stabilisation mechanism. A fundamental characteristic was that flame stabilisation did not rely on flow recirculation. The flames were maintained at a position where the local mass flux balanced the burning rate, resulting in a freely propagating turbulent flame front. The absence of physical surfaces in the vicinity of the flame provided free access for laser diagnostics. Stereoscopic Planar Image Velocimetry (SPIV) was applied to obtain the three components of the instantaneous velocity vectors on a vertical plane above the burner at the point of flame stabilisation. The instantaneous temperature fields were determined through Laser Induced Rayleigh (LIRay) scattering. Planar Laser Induced Fluorescence (PLIF) of acetone was used to calculate the average equivalence ratio distributions. Instantaneous turbulent burning velocities were extracted from SPIV results, while flame curvature and flame thermal thickness were calculated using the instantaneous temperature fields. The PDFs of these quantities were analysed to consider the separate influence of equivalence ratio stratification and turbulence. Increased levels of turbulence resulted in the expected higher turbulent burning velocities and flame front wrinkling. Flames characterised by higher fuel gradients showed higher turbulent burning velocities. Increased fuel concentration gradients gave rise to increased flame wrinkling, particularly when associated with positive small radius of curvature. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Numerical computations and optical diagnostics of unsteady partially premixed methane/air flames

The structures and dynamics of unsteady laminar partially premixed methane/air Bunsen flames are studied by means of numerical simulations, OH and CH PLIF imaging, and high speed chemiluminescence imaging employing a high framing speed intensified charge coupled device camera. The Bunsen burner has a diameter of 22 mm. Rich methane/air mixtures with an equivalence ratio of 1.5 are injected from the burner into atmosphere at different flow speeds ranging from 0.77 to 1.7 m/s, with Reynolds numbers based on the nozzle flow ranging from 1100 to 2500. The numerical simulations are based on a two-scalar flamelet manifold tabulation approach. Detailed chemistry is used to generate the flamelet manifold tabulation which relates the species concentrations, reaction rates, temperature and density to a distance function G and mixture fraction Z. Two distinct reaction zones are identified using CH and OH PLIF imaging and numerical simulations; one inner reaction zone corresponds to premixed flames on the rich side of the mixture and one outer reaction zone corresponds to mixing controlled diffusion flames on the lean side of the mixture. Under normal gravity conditions both the inner premixed flames and the outer diffusion flames are unsteady. The outer diffusion flames oscillate with a flickering frequency of about 15 Hz, which slightly increases with the burner exit velocity. The inner premixed flames are more random with much more small-scale wrinkling structures. Under zero gravity conditions the outer diffusion flames are stable whereas the inner premixed flames are unstable and highly wrinkled. It appears that the outer diffusion flames are governed by the Rayleigh-Taylor instability whereas the inner premixed flames are dictated by Landau-Darrieus instability. The two-scalar flamelet approach is shown to capture the basic structures and dynamics of the investigated unsteady partially premixed flames. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Phenomena in oscillating downward propagating flames induced by external laser irradiation method

Experiments in C{sub 2}H{sub 4}/CO{sub 2}-O{sub 2} premixed flames (Le < 1) propagating downwardly in a tube have been conducted to observe transition phenomena from laminar flame front to turbulent flame propagation triggered by external laser irradiation method. To investigate the exact motions of flame tip fluctuation at the initial moment of irradiating CO{sub 2} laser, the completely flat flame front is selected as a default flame, which is corresponding to the primary acoustic instability as reported by Searby (1992). According to the time-resolved observation, the flame front exposed to CO{sub 2} laser beam shows extremely unstable flame motions in which highly curved flame front towards unburned mixture is subject to diffusive-thermal instability. Then, the sudden enhanced burning state (increased flame surface) caused by flame instability induces the secondary acoustic instability which is akin to the observation in Ref. In the present study, we report the detailed descriptions of flame fronts on the transient behaviors leading the primary acoustic instability to turbulent motions actively induced by the absorption of externally irradiated CO{sub 2} laser beam. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Extinction conditions of a premixed flame in a channel

A local refinement method is used to numerically predict the propagation and extinction conditions of a premixed flame in a channel considering a thermodiffusive model. A local refinement method is employed because of the numerous length scales that characterize this phenomenon. The time integration is self adaptive and the solution is based on a multigrid method using a zonal mesh refinement in the flame reaction zone. The objective is to determine the conditions of extinction which are characterized by the flame structure and its properties. We are interested in the following properties: the curvature of the flame, its maximum temperature, its speed of propagation and the distance separating the flame from the wall. We analyze the influence of heat losses at the wall through the thermal conductivity of the wall and the nature of the fuel characterized by the Lewis number of the mixture. This investigation allows us to identify three propagation regimes according to heat losses at the wall and to the channel radius. The results show that there is an intermediate value of the radius for which the flame can bend and propagate provided that its curvature does not exceed a certain limit value. Indeed, small values of the radius will choke the flame and extinguish it. The extinction occurs if the flame curvature becomes too small. Furthermore, this study allows us to predict the limiting values of the heat loss coefficient at extinction as well as the critical value of the channel radius above which the premixed flame may propagate without extinction. A dead zone of length 2-4 times the flame thickness appears between the flame and the wall for a Lewis number (Le) between 0.8 and 2. For small values of Le, local extinctions are observed. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Investigation of critical equivalence ratio and chemical speciation in flames of ethylbenzene-ethanol blends

This work investigates five different one-dimensional, laminar, atmospheric pressure, premixed ethanol/ethylbenzene flames (0%, 25%, 50%, 75% and 90% ethanol by weight) at their soot onset threshold ({phi}{sub critical}). Liquid ethanol/ethylbenzene mixtures were pre-vaporized in nitrogen, blended with an oxygen-nitrogen mixture and, upon ignition, burned in premixed one-dimensional flames at atmospheric pressure. The flames were controlled so that each was at its visual soot onset threshold, and all had similar temperature profiles (determined by thermocouples). Fixed gases, light volatile hydrocarbons, polycyclic aromatic hydrocarbons (PAH), and oxygenated aromatic hydrocarbons were directly sampled at three locations in each flame. The experimental results were compared with a detailed kinetic model, and the modeling results were used to perform a reaction flux analysis of key species. The critical equivalence ratio was observed to increase in a parabolic fashion as ethanol concentration increased in the fuel mixture. The experimental results showed increasing trends of methane, ethane, and ethylene with increasing concentrations of ethanol in the flames. Carbon monoxide was also seen to increase significantly with the increase of ethanol in the flame, which removes carbon from the PAH and soot formation pathways. The PAH and oxygenated aromatic hydrocarbon values were very similar in the 0%, 25% and 50% ethanol flames, but significantly lower in the 75% and 90% ethanol flames. These results were in general agreement with the model and were reflected by the model soot predictions. The model predicted similar soot profiles for the 0%, 25% and 50% ethanol flames, however it predicted significantly lower values in the 75% and 90% ethanol flames. The reaction flux analysis revealed benzyl to be a major contributor to single and double ring aromatics (i.e., benzene and naphthalene), which was identified in a similar role in nearly sooting or highly sooting ethylbenzene flames. The presence of this radical was significantly reduced as ethanol concentration was increased in the flames, and this effect in combination with the lower carbon to oxygen ratios and the enhanced formation of carbon monoxide, are likely what allowed higher equivalence ratios to be reached without forming soot. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Topology and burning rates of turbulent, lean, H 2 /air flames

Improved understanding of turbulent flames characterized by negative consumption speed-based Markstein lengths is necessary to develop better models for turbulent lean combustion of high hydrogen content fuels. In this paper we investigate the topology and burning rates of turbulent, lean (φ = 0.31), H 2 /air flames obtained from a recently published DNS database (Aspden et al., 2011). We calculate local flame front curvatures, strain rates, thicknesses, and burning velocities and compare these values to reference quantities obtained from stretched laminar flames computed numerically in three model geometrical configurations-a counterflow twin flame, a tubular counterflow flame and an expanding cylindrical flame. We compare and contrast the DNS with these model laminar flame calculations, and show both where they closely correlate with each other, as well as where they do not. These results in the latter case are shown to result from non-flamelet behaviors, unsteady effects, and curvature-strain correlations. These insights are derived from comparisons conditioned on different topological features, such as portions of the flame front with a spherical/cylindrical shape, the leading edge of the flame, and portions of the flame front with low mean curvature. We also show that reference time scales vary appreciably over the flame, and characterizing the relative values of fluid mechanic and kinetic time scales by a single value leads to erroneous conclusions. For example, there is a two order of magnitude decrease in chemical time scales at the leading edge of the front relative to its unstretched value. In conclusion, for this reason, the leading edge of the front quite closely tracks quasi-steady calculations, even in the lowest Damköhler number case, Da F ~0.005

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Direct numerical simulation of a high-pressure hydrogen micromix combustor: Flame structure and stabilisation mechanism

A high-pressure hydrogen micromix combustor has been investigated using direct numerical simulation with detailed chemistry to examine the flame structure and stabilisation mechanism. The configuration of the combustor was based on the design by Schefer et al., using numerical periodicity to mimic a large square array. A precursor simulation of an opposed jet-in-crossflow was first conducted to generate appropriate partially-premixed inflow boundary conditions for the subsequent reacting simulation. The resulting flame can be described as an predominantly-lean inhomogeneously-premixed lifted jet flame. Five main zones were identified: a jet mixing region, a core flame, a peripheral flame, a recirculation zone, and combustion products. The core flame, situated over the jet mixing region, was found to burn as a thin reaction front, responsible for over 85% of the total fuel consumption. The peripheral flame shrouded the core flame, had low mean flow with high turbulence, and burned at very lean conditions (in the distributed burning regime). It was shown that turbulent premixed flame propagation was an order-of-magnitude too slow to stabilise the flame at these conditions. Stabilisation was identified to be due to ignition events resulting from turbulent mixing of fuel from the jet into mean recirculation of very lean hot products. Ignition events were found to correlate with shear-driven Kelvin-Helmholtz vortices, and increased in likelihood with streamwise distance. At the flame base, isolated events were observed, which developed into rapidly burning flame kernels that were blown downstream. Further downstream, near-simultaneous spatially-distributed ignition events were observed, which appeared more like ignition sheets. The paper concludes with a broader discussion that considers generalising from the conditions considered here.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Observation of two different cool flame regimes of diethyl ether in a counterflow burner

This short communication reports, for the first time, the existence of two different self-sustaining cool flame regimes of diethyl ether (DEE) in a diffusion counterflow burner: a weaker autoignition-assisted cool flame near the fuel burner and a normal diffusion cool flame near the stagnation plane. Here, the results show that the normal diffusion cool flame extinction limit increases monotonically with the fuel mole fraction, while the autoignition-assisted cool flame approaches a plateau and can exist at a fuel mole fraction below the normal diffusion cool flame. It is shown that both flame regimes are governed by the same low-temperature chain-branching reaction pathway of DEE. By using in situ laser diagnostics, entrainment of unburned fuel stream to oxygen stream at the outer edge of the fuel burner is identified as the governing physical mechanism causing a partially premixed self-sustained hollow cool flame structure. The results reveal that when a fuel with high low-temperature reactivity, two different cool flame regimes can be observed in a counterflow flame experiment. Future studies with high-reactivity fuels in a counterflow burner must ensure to distinguish between the two self-sustaining cool flame regimes. Moreover, the existence of these different cool flame regimes needs to be examined so that they would not trigger an uncontrolled combustion phasing in advanced engines fed with high low-temperature reactivity fuels.

33 ADVANCED PROPULSION SYSTEMS↗