Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FEET”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

The Influence of Wing Loading on Turbofan Powered STOL Transports with and Without Externally Blown Flaps

The effects of wing loading on the design of short takeoff and landing (STOL) transports using (1) mechanical flap systems, and (2) externally blown flap systems are determined. Aircraft incorporating each high-lift method are sized for field lengths of 2,000 feet, 2,500 feet, and 3,500 feet, and for payloads of 40, 150, and 300 passengers, for a total of 18 point-design aircraft. An assumed 1975 level of technology is applied to both concepts in terms of propulsion, weights, active controls, supercritical wing methodology, and acoustics. Low-wing-loading STOL configurations with mechanical flaps are found to be competitive with externally blown flap STOL configurations over wide ranges of payload and field length for the airworthiness rules and technology improvements assumed. Because the results of design studies like this one are sensitive to the ground rules assumed, careful attention is paid to describing the assumptions. These assumptions must be understood before the results are compared with other STOL airplane studies.

Morris, R. L.↗

Low-cost methods for fabrication of aluminum-boron shapes

Deformation processing has not been seriously considered as applicable to composite fabrication, particularly if the filament (e.g., boron) lacks plasticity. When, however, the brittle filament is clad with a ductile matrix such as 6061 Al, the underlying filament is protected from damage even when cold worked severely as in drawing and rolling. These two metal-working processes have been applied successfully to produce seven ply aluminum 50 vol % boron tubes up to 2 in. O.D. by 3 feet in length and flats 1 in. in width by 2 feet in length respectively. Although adequate densification is achieved via drawing and rolling, the former has been given major emphasis. Mechanical properties of rolled and drawn flats and tubes compare favorably with those prepared by static methods. However, the objective of the presentation is to focus on lower processing costs. In specific terms, 2 in. tubes in lengths up to 12 feet can be produced for as little as $150/lb. This is possible only because standard drawbench and carbide dies can be utilized. Furthermore, the major steps including cladding, preform preparation and drawing are conducive to automation.

Divecha, A. P.↗

Water penetration study

Nine film-filter combinations have been tested for effectiveness in recording water subsurface detail when exposed from an aerial platform over a typical water body. An experimental 2-layer positive color film, a 2-layer (minus blue layer) film, a normal 3-layer color film, a panchromatic black-and-white film, and an infrared film with selected filters were tested. Results have been tabulated to show the relative capability of each film-filter combination for: (1) image contrast in shallow water (0 to 5 feet); (2) image contrast at medium depth (5 to 10 feet); (3) image contrast in deep water (10 feet plus); (4) water penetration; maximum depth where detail was discriminated; (5) image color (the spectral range of the image); (6) vegetation visible above a water background; (7) specular reflections visible from the water surface; and (8) visual compatibility; ease of discriminating image detail. Recommendations for future recording over water bodies are included.

Lockwood, H. E.↗

Film handling procedures for Skylab S-056 experiment

In a simulation conducted August 28, 1972, two rolls of Type SO-212 film were rewound in the sensitometer darkroom preparatory to processing. The first roll contained approximately 500 feet of film exposed to a resolution target and was unloaded from a can. The second roll of 1000 feet, with about 600 feet advanced to the takeup side, was in a flight magazine. The downloading and rewinding of this second roll of film is described in detail.

Maas, K. A.↗

Flight-Determined Stability and Control Derivatives for an Executive Jet Transport

A modified maximum likelihood estimation (MMLE) technique which included a provision for including a priori information about unknown parameters was used to determine the aerodynamic derivatives of the Lockheed JetStar airplane. Two hundred sixty-five maneuvers were performed with the JetStar airplane, which was modified to include direct lift controls, to obtain lateral-directional and longitudinal derivatives. Data were obtained at altitudes of 3048 meters, 6096 meters, and 9144 meters (10,000 feet, 20,000 feet, and 30,000 feet) and over an angle of attack range from approximately 3 deg to 13 deg and a Mach number range from 0.25 to 0.75. Side force generators were installed and tested in 87 maneuvers to determine their effectiveness and their effect on the other derivatives. Lateral-directional data for four flight conditions were analyzed without using a priori information to assess the effect of this feature on the results. The MMLE method generally gave consistent (repeatable) estimates of the derivatives, with the exception of the rolling moment due to yaw rate, which showed large variances.

Smith, H. J.↗

Water impact shock test system

The basic objective was to design, manufacture, and install a shock test system which, in part, would have the ability to subject test articles weighing up to 1,000 pounds to both half sine and/or full sine pulses having peak levels of up to 50 G's with half sine pulse durations of 100 milliseconds or full sine period duration of 200 milliseconds. The tolerances associated with the aforementioned pulses were +20% and -10% for the peak levels and plus or minus 10% for the pulse durations. The subject shock test system was to be capable of accepting test article sizes of up to 4 feet by 4 feet mounting surface by 4 feet in length.

Source record↗

Installation package for air flat plate collector

The Solar 2 dimensions are four feet by eight feet by two and one half inches. The collector weighs 130 pounds and has an effective solar collection area of over 29.5 square feet. This area represents 95 percent of the total surface of the collector. The installation, operation and maintenance manual, safety hazard analysis, special handling instructions, materials list, installation concept drawings, warranty and certification statement are included in the installation package.

Source record↗

Return to earth in the Space Shuttle

The mission sequence of the first Shuttle orbital test flight (OFT-1), scheduled for March 1979, is outlined with attention to the landing phase. Descent into the atmosphere will begin at 400,000 feet at a pitch angle of 40 deg. At 80,000 feet the spacecraft decelerates to Mach 2.5, and the approach and landing phase begin at around 10,000 feet. TACAN stations will supply navigation data during most of the descent, with the pilot taking over most of the control functions during the final flare-out and approach to the runway. Also outlined is the sequencing of the RCS jets and aero surfaces.

Brand, V. D.↗

Solar heating and domestic hot water system installed at Kansas City, Fire Stations, Kansas City, Missouri

The solar system was designed to provide 47 percent of the space heating, 8,800 square feet area and 75 percent of the domestic hot water (DHW) load. The solar system consists of 2,808 square feet of Solaron, model 2001, air, flat plate collector subsystem, a concrete box storage subsystem which contains 1,428 cubic feet of 0.5 inch diameter pebbles weighing 71.5 tons, a DHW preheat tank, blowers, pumps, heat exchangers, air ducting, controls and associated plumbing. Two 120 gallon electric DHW heaters supply domestic hot water which is preheated by the solar system. Auxiliary space heating is provided by three electric heat pumps with electric resistance heaters and four 30 kilowatt electric unit heaters. There are six modes of system operation.

Source record↗

Solar heating system at Quitman County Bank, Marks, Mississippi

Information on the Solar Energy Heating System installed in a single story wood frame, cedar exterior, sloped roof building is presented. The system has on-site temperature and power measurements readouts. The 468 square feet of Solaron air flat plate collectors provide for 2,000 square feet of space heating, an estimated 60 percent of the heating load. Solar heated air is distributed to the 235 cubic foot rock storage box or to the load (space heating) by a 960 cubic feet per minute air handler unit. A 7.5 ton Carrier air-to-air heat pump with 15 kilowatts of electric booster strips serve as a back-up (auxiliary) to the solar system. Motorized dampers control the direction of airflow and back draft dampers prevent thermal siphoning of conditioned air.

Source record↗

Automated solar module assembly line

The solar module assembly machine which Kulicke and Soffa delivered under this contract is a cell tabbing and stringing machine, and capable of handling a variety of cells and assembling strings up to 4 feet long which then can be placed into a module array up to 2 feet by 4 feet in a series of parallel arrangement, and in a straight or interdigitated array format. The machine cycle is 5 seconds per solar cell. This machine is primarily adapted to 3 inch diameter round cells with two tabs between cells. Pulsed heat is used as the bond technique for solar cell interconnects. The solar module assembly machine unloads solar cells from a cassette, automatically orients them, applies flux and solders interconnect ribbons onto the cells. It then inverts the tabbed cells, connects them into cell strings, and delivers them into a module array format using a track mounted vacuum lance, from which they are taken to test and cleaning benches prior to final encapsulation into finished solar modules. Throughout the machine the solar cell is handled very carefully, and any contact with the collector side of the cell is avoided or minimized.

Bycer, M.↗

Solar space heating installed at Kansas City, Kansas

The solar energy system was constructed with the 48,800 square feet warehouse to heat the warehouse area of about 39,000 square feet while an auxiliary energy system heats the office area of about 9,800 square feet. The building is divided into 20 equal units, and each has its own solar system. The modular design permits the flexibility of combining multiple units to form offices or warehouses of various size floor areas as required by a tenant. Each unit has 20 collectors which are mounted in a single row. The collectors are double glazed flat plate collectors with a gross area of 7,800 sq ft. Air is heated either through the collectors or by the electric resistance duct coils. Extracts from the site files, specifications, drawings, installation, operation and maintenance instructions are presented.

Source record↗

Icing Frequencies Experienced During Climb and Descent by Fighter-Interceptor Aircraft

Data and analyses are presented on the relative frequencies of occurrence and severity of icing cloud layers encountered by jet aircraft in the climb and descent phases of flights to high altitudes. Fighter-interceptor aircraft operated by the Air Defense Command (USAF) at bases in the Duluth and Seattle areas collected the data with icing meters installed for a l-year period. The project was part of an extensive program conducted by the NACA to collect Icing cloud data for evaluating the icing problem relevant to routine operations. The average frequency of occurrence of icing was found to be about 5 percent of the number of climbs and descents during 1 year of operations The icing encounters were predominantly in the low and middle cloud layers, decreasing above 15,000 feet to practically none above 25,000 feet. The greatest thickness of ice that would accumulate on any aircraft component (as indicated by the accretion on a small object) was measured with the icing meters. The ice thicknesses on a small sensing probe averaged less than 1/32 inch and did not exceed 1/2 inch. Such accumulations are relatively small when compared with those that can form during horizontal flight in icing clouds. The light accretions resulted from relatively steep angles of flight through generally thin cloud layers. Because of the limited statistical reliability of the results, an analysis was made using previous statistics on icing clouds below an altitude of 20,000 feet to determine the general icing severity probabilities. The calculations were made using adiabatic lifting as a basis to establish the liquid-water content. Probabilities of over-all ice accretions on a small object as a function of airspeed and rate of climb were computed from the derived water contents. These results were then combined with the probability of occurrence of icing in order to give the icing severity that can be expected for routine aircraft operations.

Perkins, Porter J.↗

Stowable Rigid Reflector

Parabolic reflector 80 feet in diameter stowed in space of only 36.5 feet long and 14.5 feet in diameter with new folding scheme. Upon command, stowed reflector is automatically deployed to full size. Petallike panels unfold from central fixed section to create inner reflector dish. Reflector is composed of rigid panels. Number of panels depend on reflector size when deployed and upon required package size when stowed.

Palmer, W. B.↗

Composite beam cap fabricator experiment definition study, volume 1

The Composite Beam Cap Fabricator (CBCF), a part of a family of machines that was designed to develop and augment the technology of space fabrication (the automatic production of basic structural members in space is described. The major components of the CBCF are described. The mill weighs approximately 1400 pounds and its size is approximately 6 feet by 2 feet by 2 feet. It is a microprocessor under a low cost-of-concept type of contract. Consequently, all components are made of commercially available hardware. Neither weight nor volume constraints were considered during the development of the machine. For example, over 3/4 of the volume enclosed by the controller units is empty.

Source record↗

High altitude aerodynamic platform concept evaluation and prototype engine testing

A design concept has been developed for maintaining a 150-pound payload at 60,000 feet altitude for about 50 hours. A 600-pound liftoff weight aerodynamic vehicle is used which operates at sufficient speeds to withstand prevailing winds. It is powered by a turbocharged four-stoke cycle gasoline fueled engine. Endurance time of 100 hours or more appears to be feasible with hydrogen fuel and a lighter payload. A prototype engine has been tested to 40,000 feet simulated altitude. Mismatch of the engine and the turbocharger system flow and problems with fuel/air mixture ratio control characteristics prohibited operation beyond 40,000 feet. But there seems to be no reason why the concept cannot be developed to function as analytically predicted.

Akkerman, J. W.↗

Continuous Fiberization of Silicon-Carbide-Nitride Precursor Resin

The objective of this project is to design and build a laboratory scale extruder and with it to fiberize 5000 continuous feet of silicon-carbide-nitride precursor resin. Subsequently the objective is extended to include the cross-linking and pyrolysis of approximately 100 feet of the resin fiber. The extruder is designed to accommodate approximately 1 cubic centimeter samples at accurately controllable rates corresponding to take-up from a single orifice of a 25 micron fiber at speeds in the 1000 feet/minute region. Positive feed delivery is achieved with a cylinder and piston driven by a geared down electric motor. Gear reduction is achieved primarily with off-the-shelf parts. Over 5000 feet of fiber, 20 to 30 micron diameter, are spun from precursor resin samples. The formation of continuous silicon carbide/silicon nitride fiber appears to be feasible.

Dunn, S. A.↗

Analysis of a range estimator which uses MLS angle measurements

A concept that uses the azimuth signal from a microwave landing system (MLS) combined with onboard airspeed and heading data to estimate the horizontal range to the runway threshold is investigated. The absolute range error is evaluated for trajectories typical of General Aviation (GA) and commercial airline operations (CAO). These include constant intercept angles for GA and CAO, and complex curved trajectories for CAO. It is found that range errors of 4000 to 6000 feet at the entry of MLS coverage which then reduce to 1000-foot errors at runway centerline intercept are possible for GA operations. For CAO, errors at entry into MLS coverage of 2000 feet which reduce to 300 feet at runway centerline interception are possible.

Downing, David R.↗