SEARCH · Engineering Papers

Results for “EV”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Design and optimization of cancellation coil topologies for a ferrite-less wireless EV charging pad

Ferrite cores are widely used in conventional wireless EV charging pads to reduce stray EMF emissions, but they can be brittle, heavy, and expensive. This work furthers the development of ferrite-less wireless charging pads by comparing an active and two distinct passive cancellation coil topologies as candidates to replace the ferrite. Using the software packages FEMM and MATLAB, each topology is optimized to find the best winding positions and radii to minimize leakage at a specified position under the side of the vehicle. The optimized designs are compared for shielding effectiveness, induced current, and efficiency. All three topologies are able to sufficiently reduce the leakage field below the ICNIRP limit of 27 μTrms with just one turn. Interestingly, we find that an array of simple passive cancellation loops performs similar to the more widely studied passive cancellation coil.

Scher, Aaron D.↗

DOE OSTI2022

Sizing Considerations for EV Dynamic Wireless Charging Systems with Integrated Energy Storage

Roadways with dynamic wireless charging systems (DWCS) enable charge-sustaining in-motion EV charging, which can reduce charging idle time while increasing range capabilities. Spatially distributed transmitter coils are controlled in response to traffic load that varies significantly minute to minute with high power levels, very short charging time, and low system utilization like wind turbine power. Traffic load estimation and localized analysis may guide effective sizing and topology adoption for feasible and scalable DWCS deployment. DWCS traffic load approximation is reviewed with measured Automated Traffic Recorder (ATR) data and statistical distributions being used to create a synthetic load analyzed using proposed metrics quantifying system utilization over time. Lumped coil section segmentation is compared between second-based distance and spatial density analysis methods, offering 17-27% greater system utilization. A peak load shifting method is proposed for traffic redirection across two tracks with optional BESS integration increasing system utilization by 50-60% depending on time-based and power reserve-based sizing and control.

Lewis, Donovin D.↗

DOE OSTI2023

Optimal Power Sharing Speed Compensation in On-road Wireless EV Charging Systems

Dynamic wireless charging of electric vehicles (EV) is an emerging technology with the potential to address range anxiety and reduce the size of batteries or provide charge-sustaining operation. Charging demand for dynamic wireless charging systems (DWCS) varies greatly in response to location-specific traffic behaviors including the number and speed of vehicles. This paper highlights the potential reduction of load variation with speed compensation and simulates opportunities to maximize the number of cars charged concurrently through “power sharing” or altering power output to slower cars while maintaining a maximum delivered energy. An improved sub-minute model for synthetic traffic is proposed to effectively model DWCS load on high speed roadways and a power electronics model is created based on an existing prototype developed by ORNL to investigate the potential for power sharing. Reductions in the average speed of traffic can greatly increase instantaneous DWCS load by as much as 26%, complicating capacity sizing. Parametric studies with a LCC-S power electronics model shows feasible power reduction of more than 20%, while maintaining a maximum achievable efficiency greater than 90%. Speed compensation on a roadway with large speed variation can reduce average power expected by 21% and increase the maximum number of cars charged simultaneously by 30%. The application of power sharing may significantly reduce load variability due to speed, allow for increased car hosting capability, and guarantee a maximum energy delivered.

Lewis, Donovin D.↗

DOE OSTI2026

A Unified Off-Board Charger for Three-Phase Inductive and Single-Phase Conductive EV Charging

This paper presents a unified off-board charger integrating a three-phase inductive power transfer (IPT) system and a single-phase conductive (plug-in) charger for electric vehicles (EVs). The proposed charger shares a high-frequency inverter and an integrated magnetic structure that enables three operating modes: conductive charging, inductive charging, and simultaneous charging. The transmitter coils for the three-phase IPT and the high-frequency transformer windings for the conductive charger are arranged on a common ferrite pad while maintaining magnetic decoupling between the two power transfer paths. The proposed unified architecture effectively increases charger utilization and power density without a proportional increase in cost, weight, or volume. Finite-element analysis using Ansys Maxwell confirms negligible coupling between the inductive and conductive coils, and the extracted parameters are employed in PLECS simulations to verify the independent operation of each charging mode.

Jo, Cheolhui [ORNL] (ORCID:0000000322692434)↗

DOE OSTI2026

Multi-Objective Boundary Analysis of Discrete and Integrated SiC FET Modular Non-inverting Buck and Boost Converters for Fuel Cell EVs

This paper presents a multi-objective analysis of discrete and integrated SiC FET-based non-inverting buck-boost converter modules for modular fuel cell electric vehicle (EV) systems. Two converter ratings, 60 kW and 90 kW, are evaluated for both implementations, scalable up to 420 kW and 450 kW, respectively. Performance is assessed across efficiency, volumetric and gravimetric power density, cost, thermal stress, and estimated lifetime, where lifetime is derived from SiC FET B10 power-cycling data and junction temperature variations at rated power. A normalized overall performance index combined with a Pareto-boundary framework is used to identify configurations that optimally balance competing objectives. Results show that most configurations lie on the Pareto front, providing balanced trade-offs, while certain high-power discrete (90 kW at 450 kW) and integrated (60 kW at 180−420 kW) configurations are dominated. In general, discrete modules are more favorable for lower-power modular systems due to higher power density and lower cost, whereas integrated modules become more advantageous at higher power levels due to improved thermal behavior and longer lifetime. These findings provide practical design guidance for scalable fuel cell converter architectures and highlight the importance of system-level trade-offs in modular power electronics design.

Asa, Erdem [ORNL] (ORCID:0000000190884812)↗

DOE OSTI2024

1.1 eV GaInAs Cell Development for Dual-Use Solar and 1070 nm Laser Power Converters

Dual-use power converter cells can receive solar and laser power simultaneously to generate current, an application relevant to space and terrestrial industries. This study investigates two concepts of solar cells optimized for dual-use 1070 nm laser and solar power conversion, a single-junction and triple-junction cell. Because it is bandgap-tuned for a 1070 nm laser, the 1.1 eV junction is incorporated into each of the two designs, making its development key to the success of both concepts. Efficiency data for a one junction GaInAs cell demonstrates a laser conversion efficiency of 38% at 1070nm wavelength without an anti-reflection coating. However, the single-junction device requires optimization to reduce short wavelength absorption of the broad solar spectrum. In both devices, the graded buffer layers in the GaInAs cell affects the cell's performance by reducing threading dislocations in the active junction. However, the buffer in the three-junction device also acts as a lateral transport layer and so affects the fill factor depending on its sheet resistance. By varying the buffer thickness, we demonstrate a direct relationship between buffer thickness and sheet resistance reduction, while considering implications to open-circuit voltages. We also performed resistance modeling to determine the optimal grid spacing and thickness of the grid fingers to minimize losses due to sheet resistance and grid shading.

junctions↗

DOE OSTI2021

A Field Enhancement Integration Design Featuring Misalignment Tolerance for Wireless EV Charging Using LCL Topology

This article proposes a magnetic integration design for EV wireless power transfer (WPT) systems, where the compensation and transmitting coils overlap one on top of the other to share the ferrite layer without any decoupling consideration. The magnetic field generated by both the compensation and transmitting coils are exploited to transfer power. To this end, a compensation method is proposed to enable magnetic field enhancement without any reactive power flow between the compensation and the transmitting coils, and to achieve input zero phase angle and constant current output. In addition, an efficient finite element analysis-based coil optimization algorithm is proposed to improve the coil misalignment tolerance on the horizontal plane, in which a reversely connected inner coil is used to stabilize the system output under misalignment conditions. Analytical and simulation results confirm transmission flux density enhancement and reduced leakage field characteristics of the proposed coil design. Finally, a scaled-down WPT prototype is built and tested to verify the performance and effectiveness of the design. The proposed design achieves 91.17% efficiency and misalignment tolerance up to 200 mm in any XY-direction while maintaining the power transfer and its efficiency. The results of this work provide insights into magnetic integration design of high-order compensation topologies featuring higher compactness, less ferrite usage, magnetic field enhancement, and misalignment tolerance for WPT systems.

42 ENGINEERING↗

DOE OSTI2025

A Hybrid Fuel Cell and Battery Storage Power Management for Grid-Interactive EV Charging Station

With the increasing adoption of renewable energy sources in grid-interactive Electric Vehicle (EV) charging stations, the role of energy storage systems has become critical. While large energy storage systems have mitigated the intermittency of renewable energy, integrating multi-source energy management with prioritized charging can further enhance the reliability of charging stations (CS). This paper presents a decentralized energy management (DEM) approach combining battery energy storage (BES) and fuel cell (FC) systems using a rule-based line resistance correction droop (LRCD) control technique. The proposed droop control dynamically adjusts the gain to balance the state-of-charge (SoC) of the BES, enhancing power support longevity and improving battery life under varying capacity conditions by reducing current stress. Additionally, the paper addresses the challenges of using fuel cells in linear regions to optimize efficiency and manage various charging scenarios. The CS integrates unity power factor grid interaction, and power support for auxiliary loads, maintaining harmonic distortion within 5% during grid islanding. The approach evaluates DC bus voltage regulation under various scenarios of PV array power fluctuations and dynamic load variations, in both grid-connected and standalone operations. In conclusion, the proposed control strategy is validated on a laboratory prototype through various dynamic load variation and grid islanding scenarios.

Khalid, Mohd [Oak Ridge National Laboratory (ORNL)↗

DOE OSTI2025

1.1 eV GaInAs Cell Development for Dual-Use Solar and 1070 nm Laser Power Converters

Dual-use photovoltaic cells can receive solar and laser power simultaneously to generate current, an application relevant to space and terrestrial industries. This study investigates two concepts of solar cells optimized for dual-use 1070 nm laser and solar power conversion, a single-junction and triple-junction cell. The cell designs are based upon the 3- junction inverted metamorphic solar cell, previously shown highly efficient for solar conversion. Because it is closely bandgap-tuned for a 1070 nm laser, the 1 eV bottom junction is incorporated into each of the two designs, making its development key to the success of both concepts. However, each design requires some modification for efficient dual use. The single-junction device requires optimization to reduce short wavelength absorption of the broad solar spectrum. In both devices, the graded buffer layers in the GaInAs cell affect the cell's performance by reducing threading dislocations in the active junction. However, the buffer in the three-junction device also acts as a lateral transport layer and so affects the fill factor depending on its sheet resistance. By varying the buffer thickness, we demonstrate a direct relationship between buffer thickness and sheet resistance reduction, while considering implications to open-circuit voltages. We also performed resistance modeling to determine the optimal grid spacing and thickness of the grid fingers to minimize losses due to sheet resistance and grid shading. Efficiency data for a one junction GaInAs cell demonstrates a laser conversion efficiency of 38% at 1070 nm wavelength without an anti-reflection coating.

dual-use↗

DOE OSTI2025

Implementation of ISO 15118-202 messages within Everest EV Charging Open Source Framework [SWR-25-56]

This software implements the messages defined in the ISO 15118-202 standard within the Everest EV Charging open source framework. The protocol and messages defined in the ISO 15118-202 standard enable the exchange of additional information which is not available for exchange within the currently deployed EV/EVSE communications protocols. This information includes co-identification parameters, error message exchange and more. This fork of the everest-core repository adds a prototype of the Extensible Supply Equipment Communication Controller (SECC) Discovery Protocol (ESDP) implemented based on a draft of the ISO 15118-202 standard. This is achieved through additions and modifications to the EvseV2G module. The implementation provides a demonstration of the ESDP messages, encoding and decoding but does not include a full integration within the Everest framework. Much of the information being sent over ESDP in this implementation is set statically for the sake of demonstrating the protocol itself. This fork of the ext-switchev-iso15118 repository adds a prototype of the Extensible Supply Equipment Communication Controller (SECC) Discovery Protocol (ESDP) implemented based on a draft of the ISO 15118-202 standard. The implementation provides a demonstration of the ESDP messages, encoding and decoding but does not include a full integration within the Everest framework. Much of the information being sent over ESDP in this implementation is set statically for the sake of demonstrating the protocol itself. This fork adds the ESDP features for only the EVCC controller because that is the only portion that is utilized in the everest Software-in-the-Loop.

Watt, Ed [National Renewable Energy Laboratory (NR↗

DOE OSTI2025

HOPE (Hybrid and Optimized Energy and Power Management for DC Distributed EV Charging Hubs) [SWR-25-22]

HOPE is an MPC-based, optimized and robust controller algorithm developed for the energy and power management of DC distributed EV charging hubs.

Ucer, Emin [National Renewable Energy Laboratory (↗

DOE OSTI2022

ReachNow EV Driving Data From Seattle, WA, Portland, OR, and New York, NY

ReachNow provided Idaho National Laboratory (INL) with a dataset describing approximately 49,000 trips taken by customers and employees in approximately 100 BMW i3 EVs operating in ReachNow's free-floating car-sharing fleets in Seattle, WA, Portland, OR, and New York, NY between May 2016 and February 2017. Data fields include vehicle rental period start and end timestamps, the location where vehicles were parked at the start and end of rental periods, and distance driven during rental periods. A field categorizing the user during each rental period is also included. This field makes it possible to identify when vehicles were rented by customers and when vehicles were driven by fleet management team employees to reposition, charge, or service the vehicles.