Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Dynamic stiffness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Development of a Probabilistic Component Mode Synthesis Method for the Analysis of Non-Deterministic Substructures

Standard methods of structural dynamic analysis assume that the structural characteristics are deterministic. Recognizing that these characteristics are actually statistical in nature, researchers have recently developed a variety of methods that use this information to determine probabilities of a desired response characteristic, such as natural frequency, without using expensive Monte Carlo simulations. One of the problems in these methods is correctly identifying the statistical properties of primitive variables such as geometry, stiffness, and mass. This paper presents a method where the measured dynamic properties of substructures are used instead as the random variables. The residual flexibility method of component mode synthesis is combined with the probabilistic methods to determine the cumulative distribution function of the system eigenvalues. A simple cantilever beam test problem is presented that illustrates the theory.

Brown, Andrew M.↗
NASA NTRS1988

An experimental and analytical evaluation of the tapered tension-torsion strap concept

A new free-tip rotor moment controller designed to increase torque output (a restoring moment) was proposed. The controller would be used as a retention device for the freely pitching tip of a helicopter rotor. The new design featured a tapered tension-torsion strap instead of the previously used parellel strap. A tapered strap has a larger separation between the tension wires at the retention end than at the oscillating end; separation is equal at both ends for a parallel strap. A simple dynamic analysis was developed and an experiment performed to evaluate this tapered strap concept. The test results indicated that the torsional spring stiffness of the strap, represented by a torsional pendulum, increased with the amount of taper. The predicted dynamic characteristics of the pendulum also confirmed this observation and correlated reasonably well with the experimental results. It could be concluded from the experimental and analytical results that the tapered strap accomplished increased torque output when compared to the parellel strap.

Louie, Alexander↗
NASA NTRS1973

Liquid rocket propellant feedline dynamics

An analytical and experimental study of liquid rocket propellant feedline dynamics has been performed. The analytical model, which includes the effects of turbulent flow, distributed and local compliances, bellows, side branches, and structural mounting stiffness, was verified by an experimental program. Water was used as the internal fluid and the dynamic perturbations in pressure and flow were created by a piston pulser. Measurements were made to determine the pressure perturbation amplitude and phase at the line terminal due to a sinusoidal pulser excitation. The frequency response of the various line configurations tested were compared with the computed theoretical results.

Holster, J. L.↗
NASA NTRS1993

Calculation of stiffness and damping coefficients for elastically supported gas foil bearings

The stiffness and damping coefficients of an elastically supported gas foil bearing are calculated. A perfect gas is used as the lubricant, and its behavior is described by the Reynolds equation. The structural model consists only of an elastic foundation. The fluid equations and the structural equations are coupled. A perturbation method is used to obtain the linearized dynamic coefficient equations. A finite difference formulation has been developed to solve for the four stiffness and the four damping coefficients. The effect of the bearing compliance on the dynamic coefficients is discussed in this paper.

Peng, J.-P.↗
NASA NTRS1974

Development of procedures for calculating stiffness and damping properties of elastomers in engineering applications. Part 2: Elastomer characteristics at constant temperature

Dynamic properties of a commerical polybutadiene compound were determined at a constant temperature of 32 C by a forced-vibration resonant mass type of apparatus. The constant thermal state of the elastomer was ensured by keeping the ambient temperature constant and by limiting the power dissipation in the specimen. Experiments were performed with both compression and shear specimens at several preloads (nominal strain varying from 0 to 5 percent), and the results are reported in terms of a complex stiffness as a function of frequency. Very weak frequency dependence is observed and a simple power law type of correlation is shown to represent the data well. Variations in the complex stiffness as a function of preload are also found to be small for both compression and shear specimens.

Gupta, P. K.↗
NASA NTRS1994

Distributed parameter modeling of repeated truss structures

A new approach to find homogeneous models for beam-like repeated flexible structures is proposed which conceptually involves two steps. The first step involves the approximation of 3-D non-homogeneous model by a 1-D periodic beam model. The structure is modeled as a 3-D non-homogeneous continuum. The displacement field is approximated by Taylor series expansion. Then, the cross sectional mass and stiffness matrices are obtained by energy equivalence using their additive properties. Due to the repeated nature of the flexible bodies, the mass, and stiffness matrices are also periodic. This procedure is systematic and requires less dynamics detail. The first step involves the homogenization from a 1-D periodic beam model to a 1-D homogeneous beam model. The periodic beam model is homogenized into an equivalent homogeneous beam model using the additive property of compliance along the generic axis. The major departure from previous approaches in literature is using compliance instead of stiffness in homogenization. An obvious justification is that the stiffness is additive at each cross section but not along the generic axis. The homogenized model preserves many properties of the original periodic model.

Wang, Han-Ching↗
NASA NTRS1994

An investigation of angular stiffness and damping coefficients of an axial spline coupling in high-speed rotating machinery

This paper provided an opportunity to quantify the angular stiffness and equivalent viscous damping coefficients of an axial spline coupling used in high-speed turbomachinery. A unique test methodology and data reduction procedures were developed. The bending moments and angular deflections transmitted across an axial spline coupling were measured while a nonrotating shaft was excited by an external shaker. A rotor dynamics computer program was used to simulate the test conditions and to correlate the angular stiffness and damping coefficients. In addition, sensitivity analyses were performed to show that the accuracy of the dynamic coefficients do not rely on the accuracy of the data reduction procedures.

Ku, C.-P. Roger↗
NASA NTRS1978

Modal analysis of turborotors using planar modes - Theory

The generalized dynamic equations of motion have been obtained by the direct stiffness method for multimass flexible rotor bearing systems including the effects of gyroscopic moments, disk skew, and rotor acceleration. A set of undamped critical speed mode shapes calculated from the average horizontal and vertical bearing stiffness is used to transform the equations of motion into a set of coupled modal equations of motion. The modal equations are coupled by the generalized bearing coefficients and the gyroscopic moments. An analysis using only undamped critical speeds or decoupled modal analysis assuming proportional damping may lead to erroneous results. This paper presents a rapid method of calculating rotor resonance speeds with their corresponding amplification factors, stability and unbalance response of turborotors. Examples of the application of this modal approach are presented and results are compared to those of other methods such as matrix transfer analysis.

Gunter, E. J.↗
NASA NTRS1987

Adaptive control of dual-arm robots

Three strategies for adaptive control of cooperative dual-arm robots are described. In the position-position control strategy, the adaptive controllers ensure that the end-effector positions of both arms track desired trajectories in Cartesian space despite unknown time-varying interaction forces exerted through the load. In the position-hybrid control strategy, the adaptive controller of one arm controls end-effector motions in the free directions and applied forces in the constraint directions, while the adaptive controller of the other arm ensures that the end-effector tracks desired position trajectories. In the hybrid-hybrid control strategy, the adaptive controllers ensure that both end-effectors track reference position trajectories while simultaneously applying desired forces on the load. In all three control strategies, the cross-coupling effects between the arms are treated as disturbances which are rejected by the adaptive controllers while following desired commands in a common frame of reference. The adaptive controllers do not require the complex mathematical model of the arm dynamics or any knowledge of the arm dynamic parameters or the load parameters such as mass and stiffness. The controllers have simple structures and are computationally fast for on-line implementation with high sampling rates.

Seraji, H.↗
NASA NTRS1996

Predictions of Control Inputs, Periodic Responses and Damping Levels of an Isolated Experimental Rotor in Trimmed Flight

Since the early 1990s the Aeroflightdynamics Directorate at the Ames Research Center has been conducting tests on isolated hingeless rotors in hover and forward flight. The primary objective is to generate a database on aeroelastic stability in trimmed flight for torsionally soft rotors at realistic tip speeds. The rotor test model has four soft inplane blades of NACA 0012 airfoil section with low torsional stiffness. The collective pitch and shaft tilt are set prior to each test run, and then the rotor is trimmed in the following sense: the longitudinal and lateral cyclic pitch controls are adjusted through a swashplate to minimize the 1/rev flapping moment at the 12 percent radial station. In hover, the database comprises lag regressive-mode damping with pitch variations. In forward flight the database comprises cyclic pitch controls, root flap moment and lag regressive-mode damping with advance ratio, shaft angle and pitch variations. This report presents the predictions and their correlation with the database. A modal analysis is used, in which nonrotating modes in flap bending, lag bending and torsion are computed from the measured blade mass and stiffness distributions. The airfoil aerodynamics is represented by the ONERA dynamic stall models of lift, drag and pitching moment, and the wake dynamics is represented by a state-space wake model. The trim analysis of finding, the cyclic controls and the corresponding, periodic responses is based on periodic shooting with damped Newton iteration; the Floquet transition matrix (FTM) comes out as a byproduct. The stabillty analysis of finding the frequencies and damping levels is based on the eigenvalue-eigenvector analysis of the FTM. All the structural and aerodynamic states are included from modeling to trim analysis. A major finding is that dynamic wake dramatically improves the correlation for the lateral cyclic pitch control. Overall, the correlation is fairly good.

Gaonkar, G. H.↗
NASA NTRS1999

Rippling Instability of a Collapsing Bubble

The rippling instability of a liquid sheet was first observed by Debregeas, de Gennes, an Brochard-Wyart [Science 279, 1704 (1998)] on a hemispherical bubble resting on a free surface. Unlike a soap bubble, it collapses under its own weight while bursting, and folds into a wavy structure which breaks the original axisymmetry. In fact, this effect occurs for both purely elastic and purely viscous (liquid) sheets, and an analogy can be made between the two mechanisms. We present a theory for the onset of the instability in both cases, in which the growth of the corrugation out of an inextensible initial condition is governed by the competition between gravitational and bending (shearing) forces. The instability occurs for a range of densities, stiffnesses (viscosities), and sizes, a result which arises less from dynamics than from geometry, suggesting a wide validity. We further obtain a quantitative expression for the number of ripples. Finally, we present the results of experiments, which are consistent with our predictions.

daSilveira, Rava↗
NASA NTRS1991

Dual-arm manipulators with adaptive control

The described and improved multi-arm invention of this application presents three strategies for adaptive control of cooperative multi-arm robots which coordinate control over a common load. In the position-position control strategy, the adaptive controllers ensure that the end-effector positions of both arms track desired trajectories in Cartesian space despite unknown time-varying interaction forces exerted through a load. In the position-hybrid control strategy, the adaptive controller of one arm controls end-effector motions in the free directions and applied forces in the constraint directions; while the adaptive controller of the other arm ensures that the end-effector tracks desired position trajectories. In the hybrid-hybrid control strategy, the adaptive controllers ensure that both end-effectors track reference position trajectories while simultaneously applying desired forces on the load. In all three control strategies, the cross-coupling effects between the arms are treated as disturbances which are compensated for by the adaptive controllers while following desired commands in a common frame of reference. The adaptive controllers do not require the complex mathematical model of the arm dynamics or any knowledge of the arm dynamic parameters or the load parameters such as mass and stiffness. Circuits in the adaptive feedback and feedforward controllers are varied by novel adaptation laws.

Seraji, Homayoun↗
NASA NTRS1995

Method and apparatus for adaptive force and position control of manipulators

The described and improved multi-arm invention of this application presents three strategies for adaptive control of cooperative multi-arm robots which coordinate control over a common load. In the position-position control strategy, the adaptive controllers ensure that the end-effector positions of both arms track desired trajectories in Cartesian space despite unknown time-varying interaction forces exerted through a load. In the position-hybrid control strategy, the adaptive controller of one arm controls end-effector motions in the free directions and applied forces in the constraint directions; while the adaptive controller of the other arm ensures that the end-effector tracks desired position trajectories. In the hybrid-hybrid control strategy, the adaptive controllers ensure that both end-effectors track reference position trajectories while simultaneously applying desired forces on the load. In all three control strategies, the cross-coupling effects between the arms are treated as disturbances which are compensated for by the adaptive controllers while following desired commands in a common frame of reference. The adaptive controllers do not require the complex mathematical model of the arm dynamics or any knowledge of the arm dynamic parameters or the load parameters such as mass and stiffness. Circuits in the adaptive feedback and feedforward controllers are varied by novel adaptation laws.

Seraji, Homayoun↗
NASA NTRS1986

Control/structures interaction study of two 300 KW dual-keel space station concepts

The results of an investigation of the influence of structural stiffness of the space station framework on the controllability of two 300 kw class, solar dynamic powered, dual-keel space station designs are presented. The two design concepts differed only in the truss bay dimensions of the structural framework of the stations. Two control studies were made: (1) A study of the interaction of the framework structural response with the reaction control system used for attitude control during an orbital reboost maneuver; and (2) A study of the stability of the space station attitude control system with sensors influenced by the elastic deformations of the station framework. Although both configurations had acceptable control characteristics, the configuration with the larger truss bay dimension and its increased structural stiffness had more attractive characteristics for pointing control of the solar dynamic system during reboost and for attitude control during normal in-orbit operations.

Young, J. W.↗
NASA NTRS1977

The influence of pitch-lag coupling on the predicted aeroelastic stability of the XV-15 tilting proprotor aircraft

The predicted dynamic stability of the XV-15 tilting proprotor aircraft in cruise flight is updated, using a reduced increase in the pitch gimbal coupling with collective, and a higher nominal control system stiffness. The major influence of the pitch-lag coupling of the XV-15 gimballed, stiff-inplane rotor on the aircraft stability is shown. The influence of the blade pitch dynamics is found to be contained primarily in the quasistatic pitch-lag and pitch-gimbal coupling, although the complete dynamics is retained in the analysis for an accurate quantitative calculation of the stability boundary.

Johnson, W.↗
NASA NTRS1981

Study of liquid slosh in the tracking and data relay satellite hydrazine tanks

An experimental study was conducted to provide data for evaluation of the parameters for an analytical mechanical model representation of liquid/interface dynamics in the TDRSS propellant tanks. Models were developed for two liquid-under ullage (forward tank) configurations and for one liquid-over-ullage (aft tank) configuration. However, additional test runs were conducted with liquids of different densities in both cases to allow separation of bladder stiffness and gravity effects under various simulated steady acceleration conditions. Both static and dynamic parameters are evaluated to provide a good prediction of observed results.

Kana, D. D.↗
NASA NTRS1992

Robust manipulator controller specification and design

This paper suggests the use of a model based control law which uses joint rate feedback to stabilize the contact modes, and joint velocity feedforward to provide the required freespace performance throughout a task. An additional benefit of this controller is the capability to stiffen a soft manipulator. This provides an option for impedance control to provide any desired manipulator stiffness. Impedance control is implemented as an outer Cartesian loop which uses the dynamic relationship between manipulator commanded position and applied force to change the mechanical impedance through programmable filter coefficients. The impedance control discussed in this paper does not give the capability to specify the full impedance of the manipulator. However, it does give the capability to specify the manipulator Cartesian stiffness while maintaining stability in contact with the environment. This controller was designed for the Flight Telerobotic Servicer dextrous manipulator and has been validated experimentally on a single joint controller, as well as on 3 DOF planar arms.

Goldenberg, Stewart↗