Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Dynamic parameter”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Effect of cyclic conditions on the dynamic oxidation of gas turbine superalloys

The effects of operating parameters of a dynamic apparatus used to study oxidation and thermal fatigue of gas turbine materials were studied. IN-100, TD-NiCr, and WI-52 were tested at a maximum temperature of 1,090 deg C. Heating time per cycle was varied from 1/20 hr to 10 hr. Minimum temperatures between heating cycles were room temperature, 430 deg, and 650 deg C. Cooling air velocities were zero, Mach 0.7, and Mach 1. Increasing the number of cycles for a given time at temperature increased weight loss. Thermal fatigue was related to number of cycles more than to time at temperature.

Johnston, J. R.↗
NASA NTRS1991

Multistage Estimation Of Frequency And Phase

Conceptual two-stage software scheme serves as prototype of multistage scheme for digital estimation of phase, frequency, and rate of change of frequency ("Doppler rate") of possibly phase-modulated received sinusoidal signal in communication system in which transmitter and/or receiver traveling rapidly, accelerating, and/or jerking severely. Each additional stage of multistage scheme provides increasingly refined estimate of frequency and phase of signal. Conceived for use in estimating parameters of signals from spacecraft and high dynamic GPS signal parameters, also applicable, to terrestrial stationary/mobile (e.g., cellular radio) and land-mobile/satellite communication systems.

Kumar, Rajendra↗
NASA NTRS2020

A Modeling Approach for Handling Qualities and Controls Safety Analysis of Electric Air Taxi Vehicles

The combination of modern advances in electric propulsion, fly-by-wire controls, autonomy, and increasing demand for short range air taxi operations, is currently producing an outburst of vehicle designs more diverse than ever before. Advanced software tools are needed to support the rapid and safe introduction of any design into the airspace, including the safety of the deployed flight control system and vehicle handling qualities. This paper presents a methodology for building air taxi vehicle models with distributed electric propulsion for use in analyzing flight control system safety at the conceptual design level.The approach builds on existing software tools capable of outputting aeromechanics-based linear perturbation models for Vertical Take-off and Landing vehicles with multiple rotors. Rotor torque inputs are then converted into equivalent voltage control inputs, and the linear state and input dynamics matrices are modified to include electric motor dynamics with common parameters for direct-current electric motors. The linear perturbation dynamics are then stitched across multiple operating points into a quasi-Linear Parameter Varying model that covers the full flight envelope. A Model Predictive Controller is developed for use with the full envelope model, and a tradeoff analysis between handling quality and motor requirements is demonstrated using a six passenger NASA air taxi reference design.

Urban Air Mobility↗
NASA NTRS1979

A concept for dynamic control of RPV information system parameters

A globally adaptive image compression structure has been developed for use in the tactical environment of a remotely piloted vehicle. The control structure is based on an image compression algorithm RM2 but can be easily extended to standard algorithms. It is shown that this structure provides an operator with the flexibility to dynamically maximize the usefulness of a limited and changing bit rate and should significantly improve overall system performance in tactical environments.

Rice, R. F.↗
NASA NTRS1993

Improvements in ERBS attitude determination without gyros

Previous papers have described the modification of the Earth Radiation Budget Satellite (ERBS) Attitude Determination System (ADS) to overcome the impact of on board gyro degradation and failure on attitude ground support of the mission. Two approaches were taken: implementing a Kalman filter in place of the batch-least-squares attitude estimator to account for the propagation error produced by high-noise gyro data, and modeling the ERBS attitude dynamics to restore rate information in the case of gyro failure. Both of these methods had shortcomings. In practice, the filter attitude diverged without complete sensor observability, and accurate dynamics modeling required knowledge of disturbance torque parameters that had to be determined manually. These difficulties have been overcome by improved tuning of the filter and by incorporating dynamics parameter estimation into the ERBS ADS.

Chu, D.↗
NASA NTRS1987

Maximum likelihood identification using an array processor

Maximum likelihood estimation (MLE) is a method used to calculate the parameters of a dynamic system. It can be applied to a large class of problems and has good statistical properties. The main disadvantage of the MLE method is the amount of computation required. This paper describes how the computation time can be reduced significantly by using an array processor. The estimation of the parameters of a dynamic model of the Space Station is used as an example to evaluate the method.

Sridhar, Banavar↗
NASA NTRS2018

Dynamic Modeling using Output-Error Parameter Estimation based on Frequency Responses Estimated with Multisine Inputs

A method is developed for estimating model parameters, such as nondimensional stability and control derivatives, by fitting transfer function or state-space models to empirical frequency response data using the output-error approach. The frequency response data were computed using Fourier transforms of measured input and output data. The control surfaces were excited with periodic multisine inputs which facilitated time-ecient estimation of multiple-input multiple-output frequency responses. The method was applied to lateral data from a nonlinear flight dynamics simulation of the F-16 aircraft, and to longitudinal data from multiple repeated flight test maneuvers of the NASA T-2 subscale aircraft. Results using simulation data showed the frequency response method compared well to other standard methods for parameter estimation. In addition to including all the available inputs, outputs, and harmonic frequencies in the estimation, relatively small subsets of the measured data could also be used to focus on identifying specific parts of the model. Results from flight test data showed that parameter estimates and uncertainties determined from repeated maneuvers were accurate and in statistical agreement with each other.

Grauer, Jared A.↗
NASA NTRS1987

Optimal pre-scheduling of problem remappings

A large class of scientific computational problems can be characterized as a sequence of steps where a significant amount of computation occurs each step, but the work performed at each step is not necessarily identical. Two good examples of this type of computation are: (1) regridding methods which change the problem discretization during the course of the computation, and (2) methods for solving sparse triangular systems of linear equations. Recent work has investigated a means of mapping such computations onto parallel processors; the method defines a family of static mappings with differing degrees of importance placed on the conflicting goals of good load balance and low communication/synchronization overhead. The performance tradeoffs are controllable by adjusting the parameters of the mapping method. To achieve good performance it may be necessary to dynamically change these parameters at run-time, but such changes can impose additional costs. If the computation's behavior can be determined prior to its execution, it can be possible to construct an optimal parameter schedule using a low-order-polynomial-time dynamic programming algorithm. Since the latter can be expensive, the performance is studied of the effect of a linear-time scheduling heuristic on one of the model problems, and it is shown to be effective and nearly optimal.

Nicol, David M.↗
NASA NTRSDate not supplied

Gas Phase Effects on Slosh Dynamics

Gas phase effects on slosh dynamics were quantified using computational fluid dynamics (CFD) simulation for a range of propellant and ullage gas combinations. Historical slosh modeling using potential flow solutions typically neglects gas phase effects. Regardless, the results have been shown to compare well with slosh ground tests typically performed with water and air at standard temperature and pressure. CFD analysis reveals that as the liquid-to-gas density ratio decreases, slosh dynamics change due to the relative increase in gas inertia and thus influence on liquid motion. The result is a profound impact on slosh dynamics over certain parameter spaces particularly for liquid hydrogen. Gas phase effects on slosh dynamics should be considered in slosh models especially for liquid hydrogen propellant tanks.

Jacob M Brodnick↗
NASA NTRSDate not supplied

Gas Phase Effects on Slosh Dynamics

Gas phase effects on slosh dynamics were quantified using computational fluid dynamics (CFD) simulation for a range of propellant and gas combinations. Historical slosh modeling using potential flow solutions typically neglects gas phase effects. Regardless, the results have been shown to compare well with slosh ground tests typically performed with water and air at standard temperature and pressure. CFD analysis reveals that as the liquid-to-gas density ratio decreases, slosh dynamics change due to the relative increase in gas inertia and thus influence on liquid motion. The result is a profound impact on slosh dynamics over certain parameter spaces particularly for liquid hydrogen. Gas phase effects on slosh dynamics should be considered in slosh models especially for liquid hydrogen propellant tanks.

Jacob M Brodnick↗
NASA NTRSDate not supplied

Gas Phase Effects on Slosh Dynamics

Gas phase effects on slosh dynamics were quantified using computational fluid dynamics (CFD) simulation for a range of propellant and gas combinations. Historical slosh modeling using potential flow solutions typically neglects gas phase effects. Regardless, the results have been shown to compare well with slosh ground tests typically performed with water and air at standard temperature and pressure. CFD analysis reveals that as the liquid-to-gas density ratio decreases, slosh dynamics change due to the relative increase in gas inertia and thus influence on liquid motion. The result is a profound impact on slosh dynamics over certain parameter spaces particularly for liquid hydrogen. Gas phase effects on slosh dynamics should be considered in slosh models especially for liquid hydrogen propellant tanks.

Jacob M Brodnick↗
NASA NTRS1963

Launch Vehicle Flight Report - Nasa Project Apollo Little Joe 2 Qualification Test Vehicle 12-50-1

The Little Joe II Qualification Test Vehicle, Model 12-50-1, was launched from Army Launch Area 3 {ALA-3) at White Sands Missile Range, New Mexico, on 28 August 1963. This was the first launch of this class of boosters. The Little Joe II Launch Vehicle was designed as a test vehicle for boosting payloads into flight. For the Apollo Program, its mission is to serve as a launch vehicle for flight testing of the Apollo spacecraft. Accomplishment of this mission requires that the vehicle be capable of boosting the Apollo payload to parameters ranging from high dynamic pressures at low altitude to very high altitude flight. The fixed-fin 12-50 version was designed to accomplish the low-altitude parameter. The 12-51 version incorporates an attitude control system to accomplish the high altitude mission. This launch was designed to demonstrate the Little Joe II capability of meeting the high dynamic pressure parameter for the Apollo Program. For this test, a boiler-plate version of the Apollo capsule, service module and escape tower were attached to the launch vehicle to simulate weight, center of gravity and aerodynamic shape of the Apollo configuration. No attempt was made to separate the payload in flight. The test was conducted in compliance with Project Apollo Flight Mission Directive for QTV-1, NASA-MSC, dated 3 June 1963, under authority of NASA Contract NAS 9-492,

Source record↗
NASA NTRS1978

Model verification of mixed dynamic systems

A parameter-estimation method is described for verifying the mathematical model of mixed (combined interactive components from various engineering fields) dynamic systems against pertinent experimental data. The model verification problem is divided into two separate parts: defining a proper model and evaluating the parameters of that model. The main idea is to use differences between measured and predicted behavior (response) to adjust automatically the key parameters of a model so as to minimize response differences. To achieve the goal of modeling flexibility, the method combines the convenience of automated matrix generation with the generality of direct matrix input. The equations of motion are treated in first-order form, allowing for nonsymmetric matrices, modeling of general networks, and complex-mode analysis. The effectiveness of the method is demonstrated for an example problem involving a complex hydraulic-mechanical system.

Chrostowski, J. D.↗
NASA NTRS2001

Modeling, Modal Properties, and Mesh Stiffness Variation Instabilities of Planetary Gears

Planetary gear noise and vibration are primary concerns in their applications in helicopters, automobiles, aircraft engines, heavy machinery and marine vehicles. Dynamic analysis is essential to the noise and vibration reduction. This work analytically investigates some critical issues and advances the understanding of planetary gear dynamics. A lumped-parameter model is built for the dynamic analysis of general planetary gears. The unique properties of the natural frequency spectra and vibration modes are rigorously characterized. These special structures apply for general planetary gears with cyclic symmetry and, in practically important case, systems with diametrically opposed planets. The special vibration properties are useful for subsequent research. Taking advantage of the derived modal properties, the natural frequency and vibration mode sensitivities to design parameters are investigated. The key parameters include mesh stiffnesses, support/bearing stiffnesses, component masses, moments of inertia, and operating speed. The eigen-sensitivities are expressed in simple, closed-form formulae associated with modal strain and kinetic energies. As disorders (e.g., mesh stiffness variation. manufacturing and assembling errors) disturb the cyclic symmetry of planetary gears, their effects on the free vibration properties are quantitatively examined. Well-defined veering rules are derived to identify dramatic changes of natural frequencies and vibration modes under parameter variations. The knowledge of free vibration properties, eigen-sensitivities, and veering rules provide important information to effectively tune the natural frequencies and optimize structural design to minimize noise and vibration. Parametric instabilities excited by mesh stiffness variations are analytically studied for multi-mesh gear systems. The discrepancies of previous studies on parametric instability of two-stage gear chains are clarified using perturbation and numerical methods. The operating conditions causing parametric instabilities are expressed in closed-form suitable for design guidance. Using the well-defined modal properties of planetary gears, the effects of mesh parameters on parametric instability are analytically identified. Simple formulae are obtained to suppress particular instabilities by adjusting contact ratios and mesh phasing.

Parker, Robert G.↗
NASA NTRS1988

Robustness margin calculation with dynamic and real parametric uncertainty

The problem of robust stability in feedback control systems with real uncertain parameters and unmodeled dynamics, where the latter takes the form of one complex block dynamic uncertainty, is considered. A robustness margin Tm is defined with respect to such model uncertainty structure and robust stability is characterized in terms of it. An algorithm to calculate Tm and the closely related multivariable stability margin km and structured singular value mu measures of robust stability is developed. It is shown that other control problems, such as robust performance for real parametric uncertainty, can also be handled in this framework.

Sideris, Athanasios↗
NASA NTRS1986

Variable structure control of spacecraft reorientation maneuvers

A Variable Structure Control (VSC) approach is presented for multi-axial spacecraft reorientation maneuvers. A nonlinear sliding surface is proposed which results in an asymptotically stable, ideal linear sliding motion of Cayley-Rodriques attitude parameters. By imposing a desired equivalent dynamics on the attitude parameters, the approach is devoid of optimal control considerations. The single axis case provides a design scheme for the multiple axes design problem. Illustrative examples are presented.

Sira-Ramirez, H.↗