Results for “Crack control” — Page 14

NASA NTRS1982

The relative stress-corrosion-cracking susceptibility of candidate aluminum-lithium alloys for aerospace applications

Stress corrosion tests of Al-Li-Cu powder metallurgy alloys are described. Alloys investigated were Al-2.6% Li-1.4% and Al-2.6% Li-1.4% Cu-1.6% Mg. The base properties of the alloys were characterized. Process, heat treatment, and size/orientational effects on the tensile and fracture behavior were investigated. Metallurgical and electrochemical conditions are identified which provide reproducible and controlled parameters for stress corrosion evaluation. Preliminary stress corrosion test results are reported. Both Al-Li-Cu alloys appear more susceptible to stress corrosion crack initiation than 7075-T6 aluminum, with the magnesium bearing alloy being the most susceptible. Tests to determine the threshold stress intensity for the base and magnesium bearing alloys are underway. Twelve each, bolt loaded DCB type specimens are under test (120 days) and limited crack growth in these precracked specimens has been observed. General corrosion in the aqueous sodium chloride environment is thought to be obscuring results through crack tip blunting.

Pizzo, P. P.↗

NASA NTRS1960

Oxidation Behavior of Binary Niobium Alloys

This investigation concludes a study to determine the effects of up to 25 atomic percent of 55 alloying additions on the oxidation characteristics of niobium. The alloys were evaluated by oxidizing in an air atmosphere for 4 hours at 1000 C and 2 hours at 1200 C. Titanium and chromium improved oxidation resistance at both evaluation conditions. Vanadium and aluminum improved oxidation resistance at 1000 C, even though the V scale tended to liquefy and the Al specimens became brittle and the scale powdery. Copper, cobalt, iron, and iridium improved oxidation resistance at 1200 C. Other investigations report tungsten and molybdenum are protective up to about 1000 C, and tantalum at 1100 C. The most important factor influencing the rate of oxidation was the ion size of the alloy additions. Ions slightly smaller than the Nb(5+) ion are soluble in the oxide lattice and tend to lower the compressive stresses in the bulk scale that lead to cracking. The solubility of the alloying addition also depends on the valence to some extent. All of the elements mentioned that improve the oxidation resistance of Nb fit this size criterion with the possible exception of Al, whose extremely small size in large concentrations would probably lead to the formation of a powdery scale. Maintenance of a crack-free bulk scale for as long as possible may contribute to the formation of a dark subscale that ultimately is rate- controlling in the oxidation process. The platinum-group metals, especially Ir, appear to protect by entrapment of the finely dispersed alloying element by the incoming Nb2O5 metal-oxide interface. This inert metallic Ir when alloyed in a sufficient amount with Yb appears to give a ductile phase dispersed in the brittle oxide. This scale would then flow more easily to relieve the large compressive stresses to delay cracking. Complex oxide formation (which both Ti and Zr tend to initiate) and valence effects, which probably change the vacancy concentration in the scale, are masked by the overriding tendency for a porous scale.

Barrett, Charles A.↗

NASA NTRS1986

An analysis for crack layer stability

The problem of uncontrolled crack propagation and crack arrest is considered with respect to crack layer (CL) translational stability. CL propagation is determined by the difference between the energy release rate and the amount of energy required for material transformation, and necessary and sufficient conditions for CL instability are derived. CL propagation in polystyrene is studied for two cases. For the case of remotely applied fixed load fatigue, the sufficient condition of instability is shown to be met before the necessary condition, and the necessary condition controls the stability. For the fixed displacement case, neither of the instability conditions are met, and CL propagation remains stable, resulting in crack arrest.

Sehanobish, K.↗

NASA NTRS1985

Surface protection of graphite fabric/PMR-15 composites subjected to thermal oxidation

Graphite fabric/PMR-15 laminates develop matrix cracks during long-term exposure in air at temperatures in the range of 500 to 600 F. This study was performed to demonstrate the effectiveness of incorporating graphite mat surface plies as a means of reducing the developing of matrix cracks. Celion 3000 graphite fabric/PMR-15 laminates were fabricated with graphite or graphite mat/325-mesh boron powder surface plies. Laminates without mat surface plies were also fabricated for control purposes. Composite flexural strength, flexural modulus, and interlaminar shear strength were determined at 288 C before and after long-term exposure (up to 1500 hr) in air at 316 C. The results of this study showed that the incorporation of graphite mat surface plies reduces matrix cracking and improves the elevated temperature mechanical property retention characteristics of the composites.

Hanson, M. P.↗

NASA NTRS1977

Investigation of some problems in developing standards for precracked Charpy slow bend tests

The reported investigation was undertaken in connection with an attempt to develop procedures which would be useful in standardizing a test method for the precracked Charpy slow bend specimen. A number of alloys was studied for which valid plane-strain fracture toughness values have been established. The investigation shows that useful relations between precracked Charpy slow bend results and crack size factors can be obtained under some circumstances. However, it is not yet known what factors control these circumstances.

Succop, G.↗

NASA NTRS2006

Quantitative Assessment of Fatigue Damage Accumulation in Wavy Slip Metals from Acoustic Harmonic Generation

A comprehensive, analytical treatment is presented of the microelastic-plastic nonlinearities resulting from the interaction of a stress perturbation with dislocation substructures (veins and persistent slip bands) and cracks that evolve during high-cycle fatigue of wavy slip metals. The nonlinear interaction is quantified by a material (acoustic) nonlinearity parameter beta extracted from acoustic harmonic generation measurements. The contribution to beta from the substructures is obtained from the analysis of Cantrell [Cantrell, J. H., 2004, Proc. R. Soc. London A, 460, 757]. The contribution to beta from cracks is obtained by applying the Paris law for crack propagation to the Nazarov-Sutin crack nonlinearity equation [Nazarov, V. E., and Sutin, A. M., 1997, J. Acoust. Soc. Am. 102, 3349]. The nonlinearity parameter resulting from the two contributions is predicted to increase monotonically by hundreds of percent during fatigue from the virgin state to fracture. The increase in beta during the first 80-90 percent of fatigue life is dominated by the evolution of dislocation substructures, while the last 10-20 percent is dominated by crack growth. The model is applied to the fatigue of aluminium alloy 2024-T4 in stress-controlled loading at 276MPa for which experimental data are reported. The agreement between theory and experiment is excellent.

Cantrell, John H.↗

NASA NTRS1994

Fracture behavior of large-scale thin-sheet aluminum alloy

A series of fracture tests on large-scale, pre-cracked, aluminum alloy panels is being carried out to examine and to characterize the process by which cracks propagate and link up in this material. Extended grips and test fixtures were specially designed to enable the panel specimens to be loaded in tension, in a 1780-kN-capacity universal testing machine. Twelve panel specimens, each consisting of a single sheet of bare 2024-T3 aluminum alloy, 3988 mm high, 2286 mm wide, and 1.016 mm thick are being fabricated with simulated through-cracks oriented horizontally at mid-height. Using existing information, a test matrix has been set up that explores regions of failure that are controlled by fracture mechanics, with additional tests near the boundary between plastic collapse and fracture. In addition, a variety of multiple site damage (MSD) configurations have been included to distinguish between various proposed linkage mechanisms. All tests but one use anti-buckling guides. At this writing seven specimens have been tested. Three were fabricated with a single central crack, three others had multiple cracks on each side of the central crack, and one had a single crack but no anti-buckling guides. Each fracture event was recorded on film, video, computer, magnetic tape, and occasionally optical microscopy. The visual showed the crack tip with a load meter in the field of view, using motion picture film for one tip and SVHS video tape for the other. The computer recorded the output of the testing machine load cell, the stroke, and twelve strain gages at 1.5 second intervals. A wideband FM magnetic tape recorder was used to record data from the same sources. The data were analyzed by two different procedures: (1) the plastic zone model based on the residual strength diagram; and (2) the R-curve. The first three tests were used to determine the basic material properties, and these results were then used in the analysis of the two subsequent tests with MSD cracks. There is good agreement between measured values and results obtained from the model.

Dewit, Roland↗

NASA NTRS2019

Fracture Control for Additively Manufactured Spacecraft Structures

This paper describes how the intent of current NASA fracture control requirements may be applied to “fracture critical” additively manufactured spacecraft hardware. Fracture control is a multi-discipline design and certification methodology that is applied in order to mitigate catastrophic failure of structures resulting from growth of an undetected crack-like defect. The methodology is defined in existing NASA standards and is required on all human-rated space structures. As legacy spacecraft structures have been built using primarily metallic and composite materials manufactured using well established methods, guidance for application of fracture control to parts composed of these material types has been established and is documented in several NASA requirements. Additive manufactured structures offer advantages in design flexibility and manufacturing efficiency and as a result are expected to continue to be used more and more in the future. Recently, relevant guidance has been published by NASA to define materials and processes requirements for certain additive manufactured hardware, but procedures for fracture control are not addressed yet in any requirements or guidance document. While use of additive manufactured parts in non-critical scenarios may be of relatively low concern in current structural certification processes, there is a need for new fracture control guidance in order to use and certify additively manufacture hardware that is “fracture critical” where failure of the part may result in loss of life or loss of vehicle. Assurance of damage tolerance, i.e., that as-built flaws in a given part either do not exist or will not grow to become catastrophic, is of particular interest to the fracture control community. This poses a challenge due to the fact that damage tolerance behavior is not well understood in additive manufactured parts compared to legacy material types and manufacturing techniques. The discussion contained herein is necessary at this time as new guidance in this area should be founded collaboratively by the technical community at large. Different hardware types (e.g., pressure vessel, structural member) are described to highlight specific challenges and solutions for each. The discussion concludes with considering specific disciplines within fracture control (non-destructive evaluation, materials & processes, fracture mechanics, and structural certification) in a proposed extension of existing fracture control requirements to additive manufactured parts.

McElroy, Mark↗

NASA NTRS2019

Fracture Control for Additive Manufactured Spacecraft Structures

This paper describes how the intent of current NASA fracture control requirements may be applied to “fracture critical” additively manufactured spacecraft hardware. Fracture control is a multi-discipline design and certification methodology that is applied in order to mitigate catastrophic failure of structures resulting from growth of an undetected crack-like defect. The methodology is defined in existing NASA standards and is required on all human-rated space structures. As legacy spacecraft structures have been built using primarily metallic and composite materials manufactured using well established methods, guidance for application of fracture control to parts composed of these material types has been established and is documented in several NASA requirements. Additive manufactured structures offer advantages in design flexibility and manufacturing efficiency and as a result are expected to continue to be used more and more in the future. Recently, relevant guidance has been published by NASA to define materials and processes requirements for certain additive manufactured hardware, but procedures for fracture control are not addressed yet in any requirements or guidance document. While use of additive manufactured parts in non-critical scenarios may be of relatively low concern in current structural certification processes, there is a need for new fracture control guidance in order to use and certify additively manufacture hardware that is “fracture critical” where failure of the part may result in loss of life or loss of vehicle. Assurance of damage tolerance, i.e., that as-built flaws in a given part either do not exist or will not grow to become catastrophic, is of particular interest to the fracture control community. This poses a challenge due to the fact that damage tolerance behavior is not well understood in additive manufactured parts compared to legacy material types and manufacturing techniques. The discussion contained herein is necessary at this time as new guidance in this area should be founded collaboratively by the technical community at large. Different hardware types (e.g., pressure vessel, structural member) are described to highlight specific challenges and solutions for each. The discussion concludes with considering specific disciplines within fracture control (non-destructive evaluation, materials & processes, fracture mechanics, and structural certification) in a proposed extension of existing fracture control requirements to additive manufactured parts.

McElroy, Mark↗

NASA NTRS2015

Crack Instability Predictions Using a Multi-Term Approach

Present crack instability analysis for fracture critical flight hardware is normally performed using a single parameter, K(sub C), fracture toughness value obtained from standard ASTM 2D geometry test specimens made from the appropriate material. These specimens do not sufficiently match the boundary conditions and the elastic‐plastic constraint characteristics of the hardware component, and also, the crack instability of most commonly used aircraft and aerospace structural materials have some amount of stable crack growth before fracture which makes the normal use of a K(sub C) single parameter toughness value highly approximate. In the past, extensive studies have been conducted to improve the single parameter (K or J controlled) approaches by introducing parameters accounting for the geometry or in‐plane constraint effects. Using 'J‐integral' and 'A' parameter as a measure of constraint is one of the most accurate elastic‐plastic crack solutions currently available. In this work the feasibility of the J‐A approach for prediction of the crack instability was investigated first by ignoring the effects of stable crack growth i.e. using a critical J and A and second by considering the effects of stable crack growth using the corrected J‐delta a using the 'A' parameter. A broad range of initial crack lengths and a wide range of specimen geometries including C(T), M(T), ESE(T), SE(T), Double Edge Crack (DEC), Three‐Hole‐Tension (THT) and NC (crack from a notch) manufactured from Al7075 were studied. Improvements in crack instability predictions were observed compared to the other methods available in the literature.

Zanganeh, Mohammad↗

NASA NTRS2019

Fracture Control for Additive Manufactured Spacecraft Structures

Final Paper is attached. This paper discusses how the intent of current NASA fracture control requirements may be applied to "fracture critical" additive manufactured spacecraft hardware. Fracture control is a multi-discipline design and certification methodology that is applied in order to mitigate catastrophic failure of structures resulting from growth of an undetected crack-like defect. The methodology is defined in existing spacecraft standards and is required by NASA on all human-rated space structures. Recently, standards have been published by NASA to define materials and processes requirements for certain metallic additive manufactured hardware, but procedures for fracture control implementation on additive manufactured parts are not yet addressed in detail in any standard or guidance document.The discussion contained herein is necessary at this time as new guidance in this area should be founded collaboratively by the technical community at large including industry, academia, and government. Three Fracture Control Certification Methods are proposed for discussion. Additionally, a concept for "Design for AM fracture control" is introduced. The goals of this paper are to further expose the need for maturing additive manufacturing fracture control guidance in the spacecraft industry and to generate discussion on what this guidance should consist of.

McElroy, Mark↗

NASA NTRS1976

Implementation on a nonlinear concrete cracking algorithm in NASTRAN

A computer code for the analysis of reinforced concrete structures was developed using NASTRAN as a basis. Nonlinear iteration procedures were developed for obtaining solutions with a wide variety of loading sequences. A direct access file system was used to save results at each load step to restart within the solution module for further analysis. A multi-nested looping capability was implemented to control the iterations and change the loads. The basis for the analysis is a set of mutli-layer plate elements which allow local definition of materials and cracking properties.

Herting, D. N.↗

NASA NTRS1985

Development of the space shuttle body flap actuation subsystem

Development of the Body Flap Actuation Subsystem for Space Shuttles included alterations from the original design to mechanical stops, planet gears, control valves, and solenoid valves. The mechanical stops were redesigned to absorb stall load and rotating inertia of the hydraulic motors instead of only stall load. The institution of a quill shaft (torsion spring) was a successful solution. The planet gears in the geared rotary actuators developed cracks during testing. This failure was alleviated via modification to the gears. A motor pressurization - brake release timing technique was developed thru analysis and testing. This resulted in a control valve configuration which would not permit freewheeling of the body flap surface. Finally, several solenoid valve configurations were tested to obtain the desired performance. Conceptual redesigns and modifications were weighted against each other to optimize a solution. Tradeoffs were usually made between life, performance, failure tolerance, and reliability versus weight, envelope, and maintainability.

Boggs, C. R.↗

NASA NTRS1976

Materials and processes for Shuttle engine, external tank, and Solid Rocket Booster

The paper deals with the materials and processes for three Space Shuttle elements: Space Shuttle Main Engines (SSME), the External Tank (ET), and the Solid Rocket Boosters (SRB), beginning with an overview of the materials selection, tracking and control system. SSME materials and processes are considered with emphasis on hydrogen environment embrittlement, LOX/GOX compatibility, stress corrosion cracking, and hydraulic fluid testing and qualification. The ET is examined with attention given to welding and fracture mechanics, and the thermal protection system. The SRB is discussed with emphasis on corrosion prevention, stress corrosion and fracture toughness, the integrated test bed for in situ corrosion protection verification, aluminum processing, and the thermal protection system.

Schwinghamer, R. J.↗

NASA NTRS1982

The role of peel stresses in cyclic debonding

When an adhesively bonded joint is undergoing cyclic loading, one of the possible damage modes that occurs is called cyclic debonding - progressive separation of the adherends by failure of the adhesive bond under cyclic loading. In most practical structures, both peel and shear stresses exist in the adhesive bonding during cyclic loading. The results of an experimental and analytical study to determine the role of peel stresses on cyclic debonding in a mixed mode specimen are presented. Experimentally, this was done by controlling the forces that create the peel stresses by applying a clamping force to oppose the peel stresses. Cracked lap shear joints were chosen for this study. A finite element analysis was developed to assess the effect of the clamping force on the strain energy release rates due to shear and peel stresses. The results imply that the peel stress is the principal stress causing cyclic debonding.

Everett, R. A., Jr.↗

NASA NTRS1987

Bithermal Low-Cycle Fatigue Behavior of a NiCoCrAlY-Coated Single Crystal Superalloy

Specimens of a single crystal superalloy, PWA 1480, both bare and coated with a NiCoCrAlY alloy, PWA 276, were tested in low-cycle fatigue at 650 and 1050 C, and in bithermal thermomechanical fatigue tests. In the two bithermal test types, tensile strain was imposed at one of the two temperatures and reversed in compression at the other. In the high-strain regime, lives for both bithermal test types approached that for the 650 C isothermal test on an inelastic strain basis, all being controlled by the low ductility of the superalloy at 650 C. In the low-strain regime, coating cracking reduced life in the 650 C isothermal test. The bithermal test imposing tension at 650 C, termed out-of-phase, also produced rapid surface cracking, but in both coated and bare specimens. Increased crack growth rates also occurred for the out-of-phase test. Increased lives in vacuum suggested that there is a large environmental contribution to damage in the out-of-phase test due to the 1050 C exposure followed by tensile straining at the low temperature.

Gayda, J.↗

NASA NTRS1988

Cyclic fatigue damage characteristics observed for simple loadings extended to multiaxial life prediction

Fully reversed uniaxial strain controlled fatigue tests were performed on smooth cylindrical specimens made of 304 stainless steel. Fatigue life data and cracking observations for uniaxial tests were compared with life data and cracking behavior observed in fully reversed torsional tests. It was determined that the product of maximum principle strain amplitude and maximum principle stress provided the best correlation of fatigue lives for these two loading conditions. Implementation of this parameter is in agreement with observed physical damage and it accounts for the variation of stress-strain response, which is unique to specific loading conditions. Biaxial fatigue tests were conducted on tubular specimens employing both in-phase and out-of-phase tension torsion cyclic strain paths. Cracking observations indicated that the physical damage which occurred in the biaxial tests was similar to the damage observed in uniaxial and torsional tests. The Smith, Watson, and Topper parameter was then extended to predict the fatigue lives resulting from the more complex loading conditions.

Jones, David J.↗

NASA NTRS1987

Bithermal low-cycle fatigue behavior of a NiCoCrAlY-coated single crystal superalloy

Specimens of a single crystal superalloy, PWA 1480, both bare and coated with a NiCoCrAlY alloy, PWA 276, were tested in low-cycle fatigue at 650 and 1050 C, and in bithermal thermomechanical fatigue tests. In the two bithermal test types, tensile strain was imposed at one of the two temperatures and reversed in compression at the other. In the high-strain regime, lives for both bithermal test types approached that for the 650 C isothermal test on an inelastic strain basis, all being controlled by the low ductility of the superalloy at 650 C. In the low-strain regime, coating cracking reduced life in the 650 C isothermal test. The bithermal test imposing tension at 650 C, termed out-of-phase, also produced rapid surface cracking, but in both coated and bare specimens. Increased crack growth rates also occurred for the out-of-phase test. Increased lives in vacuum suggested that there is a large environmental contribution to damage in the out-of-phase test due to the 1050 C exposure followed by tensile straining at the low temperature.

Gayda, J.↗