Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Contact”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Hydrogen Sulfide Passivation for p-Type Passivated Emitter and Rear Contact Solar Cells

This work reports on the application of sulfur (S)-passivation to passivated emitter and rear contact (PERC) solar cells. The emitter surface was passivated by hydrogen sulfide (H 2 S) gas phase reaction and capped by a hydrogenated amorphous silicon nitride (a-SiN x :H) layer. The sulfur passivation on a symmetrically n + diffused emitter is shown to lead to an emitter saturation current density (J 0n+ ) of 30 fA/cm 2 at R sheet,n+ ≈ 100 Ω/sq. The application of S-passivation to the emitter surface in the PERC cell structure, with the rear surface passivated by an aluminum oxide (Al 2 O 3 )/a-SiN x :H stack, showed a promising implied open-circuit voltage (iV OC ) of 686 mV before metallization. This iV OC was higher than that for the a-SiN x :H or SiO 2 /a-SiN x :H passivated emitter surfaces (675 and 674 mV, respectively) on PERC cells processed in the same run. However, a significant drop in cell V OC is observed for the S-passivated PERC cell after the completion of device fabrication with laser patterning, screen-printed metal contact deposition, and firing. Nonetheless, an efficiency of ~20% and a V OC of ~650 mV was achieved with an emitter surface passivated by sulfur. We identified that the 760°C contact firing process degrades the S-passivation quality. Furthermore, the surface morphology was studied, and a detailed surface analysis was performed to study the causes of the S-passivated surface degradation.

14 SOLAR ENERGY↗
DOE OSTI2025

High-Throughput In-Line Deposition of Silicon Oxide for Polycrystalline Silicon Passivating Contacts

Polycrystalline silicon passivating contacts rely on an ultrathin (1–2 nm) silicon oxide layer to minimize recombination at the wafer/oxide interface and regulate dopant diffusion. Traditionally formed by thermal or chemical oxidation, this oxide is herein replaced by silicon oxide deposited via aerosol impact-driven assembly (AIDA), enabling high wafer-per-hour throughput and precise thickness control. In this study, we show that AIDA coatings conformally cover planar or textured substrates and achieve a SiO x /poly-Si(n) structure with an implied open-circuit voltage (iV oc = 726 mV) and contact saturation current density (J 0 = 8.8 fA/cm 2 ). Furthermore, annealing AIDA SiO x films at elevated temperatures desorbs hydroxyl groups while the stoichiometry transitions toward SiO 2 , improving passivation quality. Together, these results highlight AIDA’s potential for scalable, high-throughput manufacturing of advanced passivating contacts, offering a cost-effective alternative to conventional low-pressure chemical vapor deposition and plasma-enhanced chemical vapor deposition-based silicon and oxide processes.

TOPcon↗
DOE OSTI2020

Self-Aligned, Selective Area Poly-Si/SiO2 Passivated Contacts for Enhanced Photocurrent in Front/Back Solar Cells

Poly-Si/SiO 2 passivated contact front/back solar cells suffer low Jsc due to parasitic absorption in the front poly-Si layer. We demonstrate a self-aligned, selective area front contact dry-etch technique that retains the as-deposited poly-Si beneath the metal grid lines but thins it elsewhere. Jsc improves by 0.7 mA/cm 2 over our standard 40 nm thick poly-Si. Greater improvements are expected with thicker poly-Si needed for fired metal contacts. Surface passivation is slightly diminished with poly-Si thinning but can be partially restored with rehydrogenation.

14 SOLAR ENERGY↗
DOE OSTI2021

Modeling and Understanding of Rear Junction Double-Side Passivated Contact Solar Cells with Selective Area TOPCon on Front

Device modeling is performed to propose > 25% efficient industry-compatible rear junction double-side passivated contacts solar cell structure with full area p-TOPCon on the rear and selective area n-TOPCon under the front grid pattern (selective TOPCon). Here, this design enables the use of thicker TOPCon (>100nm) on the front for traditional screen-printed contacts without incurring metal-induced damage, high parasitic absorption loss, and compromise in lateral transport or carrier collection on the front. Rear junction design with appropriate bulk lifetime and resistivity combination eliminate the need for heavy doping in the front field region because carriers can flow through the bulk Si without appreciable FF loss. High VOC is maintained because high-quality Si surface passivation in the field region by Al 2 O 3 /SiN gives J 0 comparable to the TOPCon. Our device modeling specifies the practically achievable properties and parameters for each region, including full area rear p-TOPCon, selective area front n-TOPCon, bulk and contacts, to achieve 25.4% efficiency screen-printed bifacial rear junction selective TOPCon cells.

14 SOLAR ENERGY↗
DOE OSTI2022

Alternative Rear Contacts for Ultrathin CdSexTe1-x Solar Cells

The back contact is a key component for further developments of CdSeTe solar cells. In this contribution, we investigate several materials and designs that could help the development of highly-reflective, ohmic back contacts for conventional (3.45 um) and thin (800 nm) CdSeTe solar cells. We also explore numerically, nanostructured metal back contacts for light-trapping in ultrathin (200 nm) CdTe solar cells.

back contact↗
DOE OSTI2023

Loss Analysis and Performance Optimization Pathways of 729-mV Voc Si Solar Cells with Poly-Si on Locally-Etched Dielectric Passivating Contacts

In this article, the loss analysis of silicon solar cells with polysilicon on locally-etched dielectric passivating contacts with Voc=729.0 mV and efficiency=22.6% has been presented. Experimentally, nano-pinholes were introduced in SiO x (2.2 nm) and SiO x /SiN y (2.2 nm/8nm) stack using metal-assisted chemical etching (MACE). SunSolve and Quokka3 were used to simulate the experimental solar cell and investigate the optical and electrical power losses. Simulations suggest maximum power loss occurs due to recombination and resistive losses in the bulk (~0.76 mW/cm2) followed by power loss due to rear contact recombination (~0.35 mW/cm2). Recombination at the front surface also contributes to 0.24 mW/cm2. The effect of improving the bulk lifetime and lowering the recombination current density at the rear side on Voc, FF and hence, efficiency has been investigated. Further, advanced structures have been proposed to minimize recombination and parasitic absorption to achieve higher Voc and Jsc of the solar cells with locally-etched dielectric passivating contacts.

contacts↗
DOE OSTI2022

Microdroplet Electrospray Localized Laser Printing and Sintering of Nanoparticles for Passivating, Carrier-Selective Contacts (Final Technical Report)

In this project, the team used a nanoparticle electrospray laser deposition (NELD) process developed at the University of Central Florida (UCF) to address current limitations of passivating, carrier-selective contact technologies for crystalline silicon (c-Si) photovoltaic (PV) cells. The NELD process was used to print low bulk line resistivity Ag contacts directly onto transparent conductive oxides (TCOs), like indium tin oxide (ITO), for hydrogenated amorphous silicon (a-Si:H) based c-Si heterojunction (SHJ) cells without any subsequent contact firing step needed.

14 SOLAR ENERGY↗
DOE OSTI2022

Explanation and Application of the Evolving Contact Traction Fields in Shallow Foundation Systems

The present paper provides a qualitative discussion of the evolution of contact traction fields beneath rigid shallow foundations resting on granular materials. A phenomenological similarity is recognized in the measured contact traction fields of rigid footings and at the bases of sandpiles. This observation leads to the hypothesis that the stress distributions are brought about by the same physical phenomena, namely the development of arching effects through force chains and mobilized intergranular friction. A set of semi-empirical equations are suggested for the normal and tangential components of this contact traction based on past experimental measurements and phenomenological assumptions of frictional behaviors at the foundation system scale. These equations are then applied to the prescribed boundary conditions for the analysis of the settlement, resistance, and stress fields in supporting granular materials beneath the footing. A parametric sensitivity study is performed on the proposed modelling method, highlighting solutions to the boundary-value problems in an isotropic, homogeneous elastic half-space.

42 ENGINEERING↗
DOE OSTI2020

Quantitative Understanding and Implementation of Screen Printed p+ Poly-Si/Oxide Passivated Contact to Enhance the Efficiency of p-PERC Cells

This paper reports on the modeling, optimization and implementation of p-TOPCon (tunnel oxide passivated contacts) on the rear side of a PERC to enhance its efficiency. Local Al-BSF of a traditional PERC was replaced by p+ polySi/oxide passivated contact composed of ~15Å thick chemically grown tunnel oxide, capped with 120-250nm thick p+ poly-Si layer grown by LPCVD. Process optimization resulted in full area unmetallized saturated current density (Jo) of ~ 5fA/cm2 for planar surface, nearly independent of poly-Si thickness in the range. Metallized J0 showed an increase with decreased poly-Si thickness and was found to be 9.6 and ~25fA/cm2 for 250nm and 120 nm polySi, respectively, with 4.6% direct metal-Si contact fraction, suitable for bifacial cells. A 21.4% efficient baseline PERC cell with local BSF was fabricated and analyzed to extract the rear side saturation current density (J0b’) of 66fA/cm2. Model calculations showed that by replacing this local BSF with 250nm TopCon developed in the study showed some Voc enhancement of 7mV, consistent with the observed Voc increase of 10mV. Model calculations also reveal that a more advanced LBSF PERC with better bulk lifetime and emitter saturation current density can extends its potential gain up to 0.4% in cell efficiency from the integration of p-TOPCon.

14 SOLAR ENERGY↗
DOE OSTI2023

High-Performance Passivating Contacts for Si PV Based on Engineered, Doped Nanopinholes through Dielectric Layers

We present a novel, industrially relevant method to fabricate high-performance poly-Si passivating contacts for Si PV. Passivating contacts based on SiOx/poly-Si layer stacks have been implemented in record-efficiency homojunction Si solar cells. In this technology, the carrier transport through a surface-passivating SiOx is enabled either by quantum-tunneling or nanopinholes. The doped poly-Si layer provides charge-carrier selectivity. Previously, the ISFH research group demonstrated a record 26.1% efficient Si homojunction cell, where transport pinholes in ~2 nm SiOx were produced by thermal breakdown at > 1000 degrees C, which is hard to control and is surface morphology-dependent. At room temperature, our new process uses electroless plating of Ag nanoparticles, followed by metal-assisted chemical etching. Nanogalvanic corrosion yields < 20 nm-wide nanopinholes in an insulating > 2 nm SiOx layer. The nanopinholes are filled by a heavily doped a-Si:H overlayer. We drive in the dopants into the Si wafer with subsequent high-temperature annealing. Preferential incorporation of dopants at pinhole locations results in nanoscale p+/n or n+/n junctions near the wafer interface. Each heavily-doped nanoscale pinhole junction collects and transports photogenerated carriers to the cell metal contacts. The density of the engineered nanopinholes can be tuned over a wide range which is critical for optimization of device performance. The same nanogalvanic corrosion principles can be applied to produce doped transport pinholes in well-passivating thick dielectric SiOx/SiNy stacks. Importantly, our process does not rely on thermal breakdown of the dielectric layers and can be applied to textured wafers resulting in Si solar cells with > 20% conversion efficiency.

dielectric layer↗
DOE OSTI2020

Low-Dimensional Contact Layers for Enhanced Perovskite Photodiodes

Controlling defects and energy-band alignments are of paramount importance to the development of high-performance perovskite-based photodiodes. Yet, concurrent improvements in interfacial contacts and defect reduction simply by tailoring bottom contacts have not been investigated. An effective strategy is reported that can simultaneously improve energy-band alignments and structural defects by introducing low-dimensional contact (LDC) layers at the bottom interface. It is found that LDC-based perovskites considerably suppress undesirable structural defects induced by microstrains, resulting in reduced nonradiative recombination centers and improved carrier lifetimes. Additionally, the resulting LDC-based interface structures help block minority carrier injection from the electrodes by forming built-in electric fields. As a consequence, LDC-based perovskite photodiodes showed improved light detection capabilities. Finally, the result opens an avenue to yield highly efficient photodiodes.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Modeling of transport in carrier-selective contacts in silicon heterojunction solar cells

High-performance silicon heterojunction (SHJ) solar cells use carrier-selective contact structures based on hydrogentated amorphous Si (a-Si:H) to maximize collection of photogenerated carriers. The high open circuit voltages observed experimentally in SHJ cells require that the carrier-selective contacts provide selectivity and passivation. However, a microscopic understanding of the dynamics of carrier transport through the a-Si layer is currently lacking. In this paper, we explicitly simulate the transport of holes across the a-Si:H(i) layer using a novel kinetic Monte Carlo approach. The hole-selective contact structure investigated in this paper uses p-type doped a-Si:H(p) and intrinsic a-Si:H(i) on an n-type crystalline silicon wafer, where the selectivity is provided by the a-Si:H(p) and the passivation is provided by the a-Si:H(i). However, in addition to the passivation provided by the a-Si:H(i), this layer also creates a potential barrier to the collection of photogenerated holes. There have been experimental studies in the literature that have suggested that multi-phonon processes are the main transport mechanism that assists in the transport of holes across the intrinsic a-Si:H barrier. Simulations presented here show that multi-phonon injection of holes into the a-Si:H(i) layer is the rate limiting step for transport across the a-Si:H(i) layer. Our results indicate that multi-phonon transport is strongly dependent on the electric field at the a-Si:H(i)/c-Si heterointerface as well. Transport simulations presented in this paper are consistent with experimental findings that multi-phonon processes limit transport across the a-Si:H(i) layer and are responsible for photocurrent suppression at the a-Si:H(i)/c-Si heterointerface when these processes are slower than the associated incident hole flux due to photo-excitation.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Molybdenum Contacts to MoS 2 Field‐Effect Transistors: Schottky Barrier Extraction, Electrical Transport, and Low‐Frequency Noise

MoS 2 has great interest for nanoscale electronic devices, including transistors and sensors. Defect‐free structure, clean interface with the gate dielectric, and metals with suitable metal–semiconductor junctions are key for reliable devices. Molybdenum is shown as an excellent electrode for MoS 2 field‐effect transistors (FETs), but the correlation among device current, field‐effect mobility, and the low‐frequency noise (LFN) with number of atomic layers is not studied. Furthermore, the impact of Mo/MoS 2 Schottky barrier on electronic injection and scattering in the device needs to be understood. Herein, by studying the FETs with channels of different numbers of atomic‐layer thicknesses, it is shown that a molybdenum metal contact to MoS 2 provides reliable current injection with low Schottky barrier height, low contact resistance, low electron–phonon scattering, and negligible impurity scattering. The mobility and LFN are optimal at a channel thickness of ≈12 atomic layers, which is consistent with the “mobility maximum window” in MoS 2 transistors with prior studies using other contact metals.

Kwon, Jiseok↗
DOE OSTI2023

Stable Cycling with Intimate Contacts Enabled by Crystallinity–Controlled PTFE–Based Solvent–Free Cathodes in All–Solid–State Batteries

All-solid-state batteries (ASSBs) employing Li-metal anodes and inorganic solid electrolytes are attracting great attention due to high safety and energy density for next-generation energy storage devices. However, the volume change of cathode active materials can cause contact loss, resulting in charge carrier isolation, heterogeneous current distribution, and poor electrochemical properties in ASSBs. Here, a simple, yet effective, solvent-free electrode engineering approach with polytetrafluoroethylene (PTFE) as a binder for ASSBs is reported, enabling intimate contact and stable interfaces with the cathode. It is substantiated that the crystallinity of PTFE can be controlled depending on the heat history, and highly crystalline PTFE displays robust mechanical properties. High-nickel LiNi 0.8 Mn 0.1 Co 0.1 O 2 cathode prepared with crystalline PTFE show improved cycle and rate performances in ASSBs. In addition, it is revealed that the intimate contact between cathode particles with a stable cathode electrolyte layer is maintained during cycling by postmortem studies. Furthermore, this simple engineering method can be applied to prepare cathodes with a variety of active materials and solid electrolytes in ASSBs.

25 ENERGY STORAGE↗
DOE OSTI2024

Characterizing 4-string contact interaction using machine learning

Abstract The geometry of 4-string contact interaction of closed string field theory is characterized using machine learning. We obtain Strebel quadratic differentials on 4-punctured spheres as a neural network by performing unsupervised learning with a custom-built loss function. This allows us to solve for local coordinates and compute their associated mapping radii numerically. We also train a neural network distinguishing vertex from Feynman region. As a check, 4-tachyon contact term in the tachyon potential is computed and a good agreement with the results in the literature is observed. We argue that our algorithm is manifestly independent of number of punctures and scaling it to characterize the geometry ofn-string contact interaction is feasible.

Physics↗
DOE OSTI2021

The Relevance of Pion-Exchange Contributions Versus Contact Terms in the Chiral Effective Field Theory Description of Nucleon–Nucleon Scattering

The standard way to demonstrate the relevance of chiral symmetry for the NN interaction is to consider higher partial waves of NN scattering which are controlled entirely by chiral pion-exchanges (since contacts vanish). However, in applications of NN-potentials to nuclear structure and reactions, the lower partial waves are the important ones, making the largest contributions. Lower partial waves are sensitive to the short-range potential, and so, when the short-range contacts were to dominate over the chiral pion contributions in lower partial waves, then the predictions from chiral potentials would have little to do with chiral symmetry. To address this issue, we investigate systematically the role of the (chiral) one- and two-pion exchanges, on the one hand, and the effect of the contacts, on the other hand, in the lower partial waves of NN scattering. We are able to clearly identify the signature of chiral symmetry in lower partial waves. Furthermore, our study has also a pedagogical spinoff as it demonstrates in detail how the reproduction of the lower partial-wave phase shifts comes about from the various ingredients of the theory.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Direct root contact among neighboring plants influences activity of soil extracellular enzymes

Composition and diversity of vegetation systems can influence soil microbial activity and extracellular enzyme (EE) dynamics, which are crucial for soil carbon (C) accrual and nutrient cycling. Yet, the impact of plant interactions and competition on EE activities remains a notable knowledge gap. This study examines how direct root contact and neighboring plant identity affect the activity and spatial distribution of four key soil EEs: β-glucosidase (BGlu), chitinase, acid phosphatase (AcidP), and alkaline phosphatase (AlkP). Using three-compartment rhizoboxes with switchgrass (Panicum virgatum L.) grown alongside bush clover (Lespedeza capitata Michx.), and black-eyed Susan (Rudbeckia hirta L.), we assessed enzyme activities using zymography under conditions that either allowed or restricted direct root contact by root barriers. Results show that root proliferation and species interactions significantly influenced EE activity. While BGlu and AcidP activities were strongly correlated with root biomass, AlkP activity was consistently higher in the absence of root barriers, indicating a pronounced microbial response to plant interactions via direct/close root contacts. Additionally, soil phosphorus availability modulated enzyme activity, with higher phosphatase activities in low-P soils. Furthermore, these findings highlight the importance of root-root interactions and plant species composition in shaping soil biochemical processes.

enyzme activity↗
DOE OSTI2022

Evaluation of PbTe and SnTe as Ohmic Contact Layers in CdTe Solar Cell Devices

For solar cells based on CdTe, the choice of a suitable back contact material is limited by CdTe's deep work function. Here, we explored p-type PbTe and SnTe as ohmic contacts to CdTe. These contact layers were grown on single crystal CdTe substrates by molecular beam epitaxy, and the valence band offset between film and substrate was measured using X-ray photoemission spectroscopy. Polycrystalline device structures were also grown by sublimation to assess performance improvements. Doping was achieved in PbTe by thallium incorporation. Only the highest Tl doped PbTe resulted in a desirable band alignment with the CdTe, forming an electron reflector and no hole barrier. Time-resolved photoluminescence measurements also revealed significant photocarrier lifetime improvements for only the highest doped PbTe. Consequentially, devices incorporating the highest doped PbTe layers showed increased power conversion efficiency, primarily from increased fill factor. Doping of the PbTe was measured via Hall effect with variable magnetic field, which was required due to the formation of an n-type parasitic interface layer. To properly interpret the variable field Hall measurements, we derived an expression for the magnetic field-dependent conductivity tensor of an L-valley semiconductor.

anisotropic band valley↗