SEARCH · Engineering Papers

Results for “Contact”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

All sources NASA NTRS DOE OSTI

NASA NTRS2004

Solution-Assisted Optical Contacting

A modified version of a conventional optical-contact procedure has been found to facilitate alignment of optical components. The optical-contact procedure (called simply optical contacting in the art) is a standard means of bonding two highly polished and cleaned glass optical components without using epoxies or other adhesives. In its unmodified form, the procedure does not involve the use of any foreign substances at all: components to be optically contacted are dry. The main disadvantage of conventional optical contacting is that it is difficult or impossible to adjust the alignment of the components once they have become bonded. In the modified version of the procedure, a drop of an alcohol-based optical cleaning solution (isopropyl alcohol or similar) is placed at the interface between two components immediately before putting the components together. The solution forms a weak bond that gradually strengthens during a time interval of the order of tens of seconds as the alcohol evaporates. While the solution is present, the components can be slid, without loss of contact, to perform fine adjustments of their relative positions. After about a minute, most of the alcohol has evaporated and the optical components are rigidly attached to each other. If necessary, more solution can be added to enable resumption or repetition of the adjustment until the components are aligned to the required precision.

Shaddock, Daniel↗

NASA NTRS2011

Contact Graph Routing

Contact Graph Routing (CGR) is a dynamic routing system that computes routes through a time-varying topology of scheduled communication contacts in a network based on the DTN (Delay-Tolerant Networking) architecture. It is designed to enable dynamic selection of data transmission routes in a space network based on DTN. This dynamic responsiveness in route computation should be significantly more effective and less expensive than static routing, increasing total data return while at the same time reducing mission operations cost and risk. The basic strategy of CGR is to take advantage of the fact that, since flight mission communication operations are planned in detail, the communication routes between any pair of bundle agents in a population of nodes that have all been informed of one another's plans can be inferred from those plans rather than discovered via dialogue (which is impractical over long one-way-light-time space links). Messages that convey this planning information are used to construct contact graphs (time-varying models of network connectivity) from which CGR automatically computes efficient routes for bundles. Automatic route selection increases the flexibility and resilience of the space network, simplifying cross-support and reducing mission management costs. Note that there are no routing tables in Contact Graph Routing. The best route for a bundle destined for a given node may routinely be different from the best route for a different bundle destined for the same node, depending on bundle priority, bundle expiration time, and changes in the current lengths of transmission queues for neighboring nodes; routes must be computed individually for each bundle, from the Bundle Protocol agent's current network connectivity model for the bundle s destination node (the contact graph). Clearly this places a premium on optimizing the implementation of the route computation algorithm. The scalability of CGR to very large networks remains a research topic. The information carried by CGR contact plan messages is useful not only for dynamic route computation, but also for the implementation of rate control, congestion forecasting, transmission episode initiation and termination, timeout interval computation, and retransmission timer suspension and resumption.

Burleigh, Scott C.↗

DOE OSTI2021

Solar cell having a plurality of conductive contacts

The formation of solar cell contacts using a laser is described. A method of fabricating a back-contact solar cell includes forming a poly-crystalline material layer above a single-crystalline substrate. The method also includes forming a dielectric material stack above the poly-crystalline material layer. The method also includes forming, by laser ablation, a plurality of contacts holes in the dielectric material stack, each of the contact holes exposing a portion of the poly-crystalline material layer; and forming conductive contacts in the plurality of contact holes.

Harley, Gabriel↗

DOE OSTI2024

Impacts of Non-Ideal Back Contact on Capacitance Measurements in CdTe Solar Cells

CdTe solar cells suffer from a non-ideal back contact which can strongly affect the equivalent circuit model and complicate capacitance measurements. Here, five different back contact materials are deposited on identical CdTe absorbers and their influence on capacitance measurements is characterized. A five-element equivalent circuit model is shown to represent a CdTe solar cell with a non-ideal back contact, and capacitance-frequency (C-f) measurements on each sample clearly show the influence of this contact. Capacitance-voltage (C-V) measurements on each sample show the influence of frequency on measured capacitance. In the AlGaOx/Au sample, temperature dependent C-fs show the back barrier height to be 240 meV, and ongoing measurements will give a comparison of back barrier heights for all samples. This study provides insight into the efficacy of various back contacts and highlights potential errors in the interpretation of capacitance measurements due to the presence of the back contact.

14 SOLAR ENERGY↗

DOE OSTI2023

Computational design of metamaterials with self contact

Inverse homogenization in combination with contact modeling, topology optimization and shape optimization is used to design metamaterials with optimized macroscopic response. The homogenization assumes length scale separation which allows the non-linear macroscopic behavior to be obtained by analyzing a single unit cell in a lattice structure. Self contact in the unit cell, which is modeled using a third medium contact method, is leveraged to obtain a complex homogenized response. The inverse homogenization problem is initially formulated as a topology optimization problem, where the macroscopic stress–strain behavior is tuned to our liking. However, it is well known that boundary phenomena are difficult to model in topology optimization and that interface modeling is crucial to accurately analyze contact. For that reason, the boundary representation of the topology optimized design is extracted and used as initial design in a subsequent shape optimization. The behaviors of our designs are verified by performing rigorous post-processing analyzes using conforming meshes and conventional contact formulations.

42 ENGINEERING↗

DOE OSTI2026

Corrosion of 316 SS in direct contact with Zircaloy-4 in repository relevant conditions

The effects of interfacial contact between 316 stainless steel (316 SS) waste canister and spent fuel cladding material (Zircaloy-4) in case of water intrusion into a deep geological repository are investigated. Hydrothermal corrosion experiments of 316 SS and Zircaloy-4 in direct contact were performed at elevated temperatures in MilliQ water and simulated Mont Terri groundwater. Hematite, magnetite, chromite, and baddeleyite form as secondary phases. pH of the Mont Terri solution increases with corrosion duration and magnetite forms preferentially instead of hematite. Thermodynamic modeling shows that iron oxidation in 316 SS controls the pH and redox potential of the aqueous environment and is in good agreement with experimental Mont Terri results, showing that experimental Mont Terri results trend to equilibrium. All oxides except hematite are predicted to exist at thermodynamic equilibrium based on calculations, implying that experimentally formed hematite will be reduced or transformed to magnetite at equilibrium. The thermodynamically predicted chromite was observed to form only at the interface where 316 SS was in contact with Zircaloy-4 at 250°C, showing that contact with Zircaloy-4 seems to accelerate the 316 SS corrosion to thermodynamic equilibrium. Finally, Mont Terri groundwater readily trends towards thermodynamic equilibrium, leading to a pH and redox buffered system that is dominated by iron in solution coming from the accelerated corrosion of 316 SS caused by Zircaloy-4 contact.

316 stainless steel↗

DOE OSTI2021

One-dimensional edge contact to encapsulated MoS 2 with a superconductor

Establishing ohmic contact to van der Waals semiconductors such as MoS 2 is crucial to unlocking their full potential in next-generation electronic devices. Encapsulation of few layer MoS 2 with hBN preserves the material’s electronic properties but makes electrical contacts more challenging. Progress toward high quality edge contact to encapsulated MoS 2 has been recently reported. Here, we evaluate a contact methodology using sputtered MoRe, a type II superconductor with a relatively high critical field and temperature commonly used to induce superconductivity in graphene. We find that the contact transparency is poor and that the devices do not support a measurable supercurrent down to 3 K, which has ramifications for future fabrication recipes.

2D materials↗

DOE OSTI2023

Thermal Stability of Schottky Contacts and Rearrangement of Defects in β ‐Ga 2 O 3 Crystals

Abstract The thermal stability of different Schottky contacts (Au, Pt, and Ni) on (100) β ‐Ga 2 O 3 single crystals grown by the Czochralski method is investigated. Besides the examination of the Schottky barrier parameters, contact‐dependent defect levels are investigated by deep‐level transient spectroscopy (DLTS) in a 100–650 K (ramp‐up) and 650–100 K (ramp‐down) temperature cycle. Several defect levels are detected below the conduction band minimum at 0.41, 0.60, 0.77, 0.96, and 1.17 eV. In the temperature ramp‐down DLTS, the 1.17 eV level disappears, and the 0.60 eV level appears for all Schottky contacts. DFT calculations suggest that rearrangement and dissociation of a single hydrogen from a doubly‐hydrogenated Ga─O divacancy complex occurs during the temperature sweep under bias. The trap level at 0.96 eV only appears after the thermal load for the Ni contact, in contrast to Au and Pt, where it is present without a thermal budget. Temperature‐dependent leakage current (at −4 V) measurements indicate oxidation of Ni, and further thermodynamic analysis suggests alloying of Au‐Ga atoms at the Au/ β ‐Ga 2 O 3 interface. These studies provide insight into the behavior induced by these common Schottky contacts and the alteration associated with temperature cycling.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Titanium Carbide MXene Hole Contacts for CdTe Photovoltaics

CdTe is a high‐efficiency thin‐film photovoltaic technology that has seen tremendous commercial success over the past decade. Yet despite the improvement of other device characteristics, the fabrication of an ohmic hole back contact layer has remained a challenge due to the high ionization potential of CdTe, which limits the external potential that can be feasibly reached even as other characteristics of the device improve. MXenes, a family of 2D materials with rapidly growing scientific and commercial interest, offer a promising route to forming low‐cost, low‐barrier contacts due to their demonstrated high work function, metallic conductivity, and facile solution processing from benign solvents. Here, it is shown that Ti 3 C 2 T x MXene films processed from an aqueous colloidal dispersion can perform as a highly efficient hole contact material for CdTe solar cells, resulting in high power‐conversion efficiencies. The role of the Schottky barrier formation in Ti 3 C 2 T x ‐contacted CdTe devices is probed, and potential pathways for the future development of this potent combination of materials are elucidated. The modularity of the expansive MXene family of materials presents a promising strategy for developing next‐generation hole contacts for CdTe solar cells.

14 SOLAR ENERGY↗

DOE OSTI2020

Conductive spinels derived from Co–Mn based alloy precursor for SOFC cathode-side contact application

The utilization of gas-atomized Co–Mn based alloy precursor is a promising approach to lowering the sintering temperature of the spinel contact layer and enhancing its performance. In this work, simulated interconnect/contact/cathode cells are employed to investigate the effects of different metallic precursors (i.e., three Co–Mn based alloy powders and a mixture of Co + MnO 2 powders) on the microstructure and performance of the reactively-sintered MnCo 2 O 4 -based contact layer. While excellent overall electrical performance is observed for all the cells with the four contact precursors during 1000-h testing at 800 °C in air, the cell with the Ce-doped alloy contact precursor shows the lowest cell area specific resistance (ASR) and ASR degradation rate. Cross-sectional observation of the tested cells is conducted to assess the compatibility of the contact layer with adjacent components as well as its effectiveness in reducing the Cr 2 O 3 scale growth and blocking Cr migration from the interconnect to the cathode.

08 HYDROGEN↗

DOE OSTI2020

Impact of the adhesion-force lever-arm “a” on the Rock ‘n’ Roll resuspension model and how to compute it from contact mechanics

The paper proposes a methodology to fill a gap in the context of mechanistic particle resuspension models related to the adhesion and lift force lever arms ( a ): to date, only one experimental observation exists from a centrifuge experiment with a specific particle/surface pair which found r P / a = 100 and assumed that the contact points were symmetric with respect to the particle center. However, the Reeks and Hall’s (2001) model is highly sensitive to this parameter, which therefore cannot be used as-is for different particle diameters or materials. This paper proposes a methodology to compute the adhesion and lift force lever arms ( a A and a L , respectively) based on Atomic Force Microcopy (AFM) surface roughness measurements and contact mechanics arguments. In practice, a spherical, perfectly smooth particle is brought in contact (computationally) with the measured surface roughness and is then rotated by the point of contact to determine the two or more asperities over which the particle would sit on the surface. A method to compute the asperity radius of curvature is devised to compute the asperity deformation and the correct partitioning of the total deformation between the particle and the asperity is presented. For the glass surface under consideration, the asperity deformation was negligible, i.e., it was below the van der Waals radius, which is the limit of applicability of contact mechanics. The Reeks and Hall’s (2001) model is then extended to account for the joint probability of a A and a L . Significant differences in particle resuspended after a day in common atmospheric conditions are found between the approach that uses the lever-arm distributions or their mean values. Also, important differences are found when comparing the lever-arm distribution and r P / a = 100. Hence, one should be cautious of using r P / a = 100 for surface/particle pairs differing from those in the original study. Finally, limits of applicability of the theories used are presented together with considerations regarding how to extend the method to non-spherical particles and different materials.

42 ENGINEERING↗

DOE OSTI2020

Ultrathin silicon oxide prepared by in-line plasma-assisted N 2 O oxidation (PANO) and the application for n-type polysilicon passivated contact

We develop a plasma-assisted nitrous-oxide (N 2 O) gas oxidation (PANO) method to prepare the ultrathin silicon oxide (SiO x ) for polysilicon (poly-Si) passivated contact. The effects of preparation conditions, including the substrate temperature, processing time, and plasma power, are studied. Afterwards, we integrate the PANO SiO x into the polysilicon passivated contact and optimize the passivation and contact performances. Excellent surface passivation with the n-type poly-Si and PANO SiO x on the n-type c-Si wafer is achieved by 880 °C annealing, which shows competitive passivation quality to the one with NASO SiO x . Champion implied open-circuit voltage (iV oc ) and single-sided recombination saturated current (J 0 ) reach 730 mV and 4.3 fA/cm 2 after crystallization; and they are further improved to 747 mV and 2.0 fA/cm 2 (3 × 10 15 cm -3 ) after subsequent AlO x /SiN x hydrogenation. Using transmission electron microscopy (TEM), we find that the thickness of PANO SiO x ranges 1.1–2.4 nm and the controlled nitric acid oxidized SiO x (NAOS) ranges 1.3–1.8 nm. The contact resistivity (ρ c ) is typically <10 mΩ cm 2 with the annealing temperature of >820 °C. Also, the crystallinity, phosphorous in-diffusion profile, and current-leaking density of the passivated contacts are investigated. In general, the PANO SiO x and in-situ doping amorphous silicon precursor can be fabricated in one PECVD system without additional equipment or transfer procedures, which is favorable for the high-efficiency, low-cost industrial manufacture.

14 SOLAR ENERGY↗

DOE OSTI2020

Sputtered indium tin oxide as a recombination layer formed on the tunnel oxide/poly-Si passivating contact enabling the potential of efficient monolithic perovskite/Si tandem solar cells

We focus on utilizing sputtered indium tin oxide (ITO) as a recombination layer, having low junction damage to an n-type silicon solar cell with a front-side tunnel oxide passivating electron contact, thereby enabling the development of a high efficiency monolithic perovskite/Si tandem device. High transparency and low resistivity ITO films are deposited via low power DC magnetron sputtering at room temperature onto a front-side thin SiO x /n + poly-Si contact in a complete Cz n-Si cell with a back-side Al 2 O 3 /SiN x passivating boron-diffused p + -emitter on a random pyramid textured surface. We report the cell characteristics before and after ITO sputtering, and we find a cure at 250 °C in air is highly effective at mitigating any sputtering induced damage. Our ITO coated sample resulted in an implied open-circuit voltage (iV oc ) of 684.7 ± 11.3 mV with the total saturation current density of 49.2 ± 14.8 fA/cm 2 , an implied fill factor (iFF) of 81.9 ± 0.8%, and a contact resistivity in the range of 60 mΩ-cm 2 to 90 mΩ-cm 2 . After formation of a local Ag contact to the rear emitter and sputtered ITO film as the front-side contact without grid fingers, the pseudo-efficiency of 20.2 ± 0.5% was obtained with the V oc of 670.4 ± 7 mV and pseudo FF of 77.3 ± 1.3% under simulated one sun with the calculated short-circuit current density of 30.9 mA/cm 2 from the measured external quantum efficiency. Furthermore, our modelling result shows that efficiency exceeding 25% under one sun is practically achievable in perovskite/Si tandem configuration using the ITO recombination layer connecting a perovskite top cell and a poly-Si bottom cell.

14 SOLAR ENERGY↗

DOE OSTI2022

Impact of acetic acid exposure on metal contact degradation of different crystalline silicon solar cell technologies

Degradation due to acetic acid in photovoltaic (PV) modules has been a commonly observed phenomenon for both damp-heat exposure and outdoor operations. Acetic acid is a degradation byproduct of ethylene-vinyl acetate (EVA), a common module encapsulant. To address this issue, robust metallization pastes and cell technologies are being developed. However, it is important to assess how these technologies perform in an acetic acid environment and withstand degradation before they are implemented in the solar market. In this work, we investigate the impact of acetic acid exposure on four different cell groups: monofacial passivated emitter and rear contact (PERC) cells with advanced telluride-based front contact pastes, bifacial PERC cells with novel aluminum rear contact pastes, bifacial tunnel oxide passivated contacts (TOPCon) cells, and silicon heterojunction (SHJ) cells. These cells were exposed to acetic acid for different time increments. The recombination losses were characterized by Suns-VOC, and multi-variate regression analysis of intensity-dependent photoluminescence (PL) images with Griddler AI. Resistive losses were tracked with the transmission line method (TLM). Samples showing severe performance degradation were selected for further materials characterization to understand the root cause. Top-down and cross-sectional scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray photoelectron spectroscopy (XPS) were performed to investigate the change in materials properties. Our study shows that the front contacts of the bifacial TOPCon cells and monofacial PERC cells were significantly affected by acetic acid exposure. Here, the SHJ cells were found to be the most stable.

14 SOLAR ENERGY↗

DOE OSTI2024

Patterned dielectric back contact design for GaAs thermophotovoltaic devices

-Patterned-dielectric back contact structures in optoelectronic devices are designed to boost the reflectance of light from the device back surface while retaining a low-resistance pathway for electrical conductance. Their reduced light absorption at near- and sub-bandgap photon energies leads to improved luminescence in light-emitting diodes, greater photon recycling, voltage, and efficiency in photovoltaic cells, and greater recuperation of unabsorbed sub-bandgap light in thermophotovoltaic (TPV) systems. However, diffraction from the patterned features can deflect incident light in propagation directions that lead to light trapping and parasitic absorption in the cell. Here, in this article, we use rigorous coupled-wave analysis (RCWA) to study three-dimensional diffractive scattering of electromagnetic waves by periodic metal point-contact gratings on 1.42-eV GaAs TPV cells, to analyze their effect on unwanted sub-bandgap absorption in order to achieve higher TPV system efficiency. Solutions of Maxwell's equations calculated using RCWA are compared to measured sub-bandgap reflectance in experimental GaAs TPV devices with varying metal point-contact diameters and spacing. Modeling and experiments indicate decreased total reflectance due to these diffractive effects for a small point contact diameter of 1 μm, and this effect is much stronger at higher contact coverage fractions.

14 SOLAR ENERGY↗

DOE OSTI2025

Optimized NiTe 2 /Ni back contacts via chemical deposition for high performance CdTe solar cells

The development of efficient and stable back contacts remains a major challenge in achieving high performance and long-term stability of CdTe thin-film solar cells. Here, this work revisits the formation of NiTe 2 by chemical bath deposition (CBD) as a back contact for CdTe devices. An optimized CBD recipe, based on high-purity precursors and the addition of copper chloride directly into the bath, was developed and applied to fabricate Cu-doped CdTe solar cells. A modified Cu-free methodology was also applied to Group V doped absorbers. The process included pinhole filling, ion milling, CBD, annealing, and sputtering to form a low-barrier back contact. Devices fabricated using this method achieved consistent open-circuit voltages (V oc ) above 800 mV and fill factors (FF) exceeding 70%. The best Cu-doped devices reached power conversion efficiencies (PCE) above 18 %, and preliminary results with Group V-doped material demonstrated compatibility of the method with high-efficiency, state-of-the-art CdTe devices. This study shows that NiTe 2 /Ni back contacts, formed via an optimized chemical process followed by sputtering of Ni, represent a promising pathway for achieving low-barrier and potentially stable back contacts in modern CdTe photovoltaics.

14 SOLAR ENERGY↗

DOE OSTI2025

Contact Freezing of Water Droplets by Crystalline Organic Acids

The ability of water to freeze into ice crystals in mixed-phase clouds affects physical properties, including particle size, precipitation rates, and radiative properties. The presence of an insoluble particle at the surface of water droplets can promote ice nucleation at temperatures higher than that of pure water, even in the absence of a collision. However, contact freezing remains an underexplored mode of ice nucleation. Here, we present a study of atmospherically relevant organic acids and their role as effective ice-nucleating particles (INP) in contact mode using a Raman-microscope-equipped environmental chamber. We determined contact freezing temperatures induced by solid crystals of docosanol, adipic acid, cis-pinonic acid, fumaric acid, 4-hydroxybenzoic acid, palmitic acid, phthalic acid, sebacic acid, stearic acid, terephthalic acid, and vanillic acid. All solids except fumaric acid promoted contact freezing of water droplets at significantly higher temperatures than pure water in the chamber (−15.0 to −18.5 °C vs −21.3 °C). Physical and chemical properties were identified which correlate with greater effectiveness of INPs in the contact mode, including crystal lattice mismatch with ice, carbon number, and insolubility in water. In conclusion, we suggest that the presence of these organic solids in atmospheric aerosols may promote atmospheric ice nucleation at warm temperatures.

Clouds↗

DOE OSTI2021

Are Contact Angle Measurements Useful for Oxide-Coated Liquid Metals?

This work establishes that static contact angles for gallium-based liquid metals have no utility despite the continued and common use of such angles in the literature. In the presence of oxygen, these metals rapidly form a thin (~1–3 nm) surface oxide “skin” that adheres to many surfaces and mechanically impedes its flow. This property is problematic for contact angle measurements, which presume the ability of liquids to flow freely to adopt shapes that minimize the interfacial energy. We show here that advancing angles for a metal are always high (>140°)—even on substrates to which it adheres—because the solid native oxide must rupture in tension to advance the contact line. The advancing angle for the metal depends subtly on the substrate surface chemistry but does not vary strongly with hydrophobicity of the substrate. During receding measurements, the metal droplet initially sags as the liquid withdraws from the “sac” formed by the skin and thus the contact area with the substrate initially increases despite its volumetric recession. Furthermore, the oxide pins at the perimeter of the deflated “sac” on all the surfaces are tested, except for certain rough surfaces. With additional withdrawal of the liquid metal, the pinned angle gets smaller until eventually the oxide “sac” collapses. Thus, static contact angles can be manipulated mechanically from 0° to >140° due to hysteresis and are therefore uninformative. We also provide recommendations and best practices for wetting experiments, which may find use in applications that use these alloys such as soft electronics, composites, and microfluidics.

36 MATERIALS SCIENCE↗