Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Compressive limiters”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Metastability of Liquid Water Freezing into Ice VII under Dynamic Compression

The ubiquitous nature and unusual properties of water have motivated many studies on its metastability under temperature- or pressure-induced phase transformations. Here, nanosecond compression by a high-power laser is used to create the nonequilibrium conditions where liquid water persists well into the stable region of ice VII. Through our experiments, as well as a complementary theoretical/computational analysis based on classical nucleation theory, we report that the metastability limit of liquid water under nearly isentropic compression from ambient conditions is at least 8 GPa, higher than the 7 GPa previously reported for lower loading rates.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1987

Noise and compressibility in lattice-gas fluids

Computations are reported in which the hexagonal lattice gas is used to simulate two-dimensional Navier-Stokes shear flows. Limitations associated with noise in the initial loading and compressible effects associated with a velocity-dependent equation of state arise and interact with each other. A relatively narrow window in density and flow speed exhibits physical behavior.

Dahlburg, Jill P.↗
DOE OSTI2021

Gasoline fuels properties for multi-mode operation – Observations in a GDI and the CFR engine

The combustion behavior of five full boiling range RON98 gasoline blends was evaluated for multi-mode operation in a GDI and the CFR octane rating engine. The GDI engine tests were conducted with stoichiometric air-fuel ratio in spark-ignition (SI), and with air-diluted homogeneous charge compression ignition (HCCI) mode. In the CFR engine, the knocking combustion was analyzed under standard RON testing conditions at both peak knocking lambda and stoichiometric air-fuel ratios, whereas compression ignited operation was characterized by utilizing the HCCI number test protocol. Disparate knock limited SI and HCCI combustion behavior was observed for the test fuels, despite four of the fuels having the same RON and octane sensitivity. It was found that knock-limited combustion phasing in the GDI engine did not align well with the RON. However, a detailed comparison of knock-limited SI operation in the GDI and CFR engine revealed that a more appropriate effective RON based on a common knock intensity metric (MAPO) and stoichiometric air-fuel ratio resulted in comparable knock characterization between the two engine platforms. Furthermore, the critical intake air temperature and the critical compression ratio were proposed to characterize knock-limited SI operation, while the minimum intake air heating and compression ratio were used to define a fuel's autoignition propensity for compression ignition operation in the GDI and CFR engine, respectively. Finally, each fuel's characteristic compression ratio needed to obtain knock-limited SI (KLSI) and HCCI operation was used to calculate an effective multi-mode octane number (MM-ON) based on the primary reference fuel blends.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Joint Matrix Completion and Compressed Sensing for State Estimation in Low-observable Distribution System

Limited measurement availability at the distribution grid presents challenges for state estimation and situational awareness. This paper combines the advantages of two sparsity-based state estimation approaches (matrix completion and compressive sensing) that have been proposed recently to address the challenge of unobservability. The proposed approach exploits both the low rank structure and a suitable transform domain representation to leverage the correlation structure of the spatio-temporal data matrix while incorporating the powerflow constraints of the distribution grid. Simulations are carried out on three phase unbalanced IEEE 37 test system to verify the effectiveness of the proposed approach. The performance results reveal - (1) the superiority over traditional matrix completion and (2) very low state estimation errors for high compression ratios representing very low observability.

Dahale, Shweta↗
NASA NTRS1998

Low-Power CO2 Compression Technology

Presently, the most feasible processes for extracting oxygen from the Martian atmosphere either require or are much more efficient if the atmospheric CO2 feed is provided at pressures well above the Martian ambient. Electrical power for performing the desired compression is likely to be an extremely limited resource on the Mars surface. Even if "cheap" nuclear power is available at a central site/launch facility where rocket propellent and oxidant are manufactured, life support applications needing oxygen production capabilities, such as rovers, portable life support, and remote or independent exploration stations, will benefit from extremely low-power atmospheric compression technology, such as the one discussed here. Our experiments show the potential of one very low-power approach to performing CO2 compression that uses the Mars diurnal temperature cycle to drive a heat engine. The 1 kg compressor has been tested over an extended period in a Mars environmental simulation chamber that mimics the composition, pressure, and temperature cycles that can occur on the Martian surface. The simple design, which has very few moving parts and can easily be scaled to larger or smaller sizes, produces a CO2 stream at a rate of 100 g/ day at a quality and pressure suitable for a variety of oxygen production processes.

Finn, John E.↗
NASA NTRS1986

A high quality image compression scheme for real-time applications

Many image compression or coding techniques have been developed to reduce the amount of bits of information needed to represent digital images. Among these, Vector Quantization (VQ) seems to have the edge; its theoretical distortion is lower than that of other block coding techniques at comparable bit rates. However, the application of Vector Quantization remains limited due to its high computational complexity. Presently, it is limited to low to medium quality image compression. In this paper it is shown that VQ can be mapped onto VLSI implementation via systolic type architecture, making real time application possible. In addition, it is shown that using multistage or cascade VQ high quality images can be obtained at very low bit rates for real time applications while using smaller codebooks than is necessary in single stage VQ. Examples of processed images are presented.

Ramamoorthy, P. A.↗
DOE OSTI2024

An Incremental Tensor Train Decomposition Algorithm

We present a new algorithm for incrementally updating the tensor train decomposition of a stream of tensor data. This new algorithm, called the tensor train incremental core expansion (TT-ICE) improves upon the current state-of-the-art algorithms for compressing in tensor train format by developing a new adaptive approach that incurs significantly slower rank growth and guarantees compression accuracy. This capability is achieved by limiting the number of new vectors appended to the TT-cores of an existing accumulation tensor after each data increment. These vectors represent directions orthogonal to the span of existing cores and are limited to those needed to represent a newly arrived tensor to a target accuracy. We provide two versions of the algorithm: TT-ICE and TT-ICE accelerated with heuristics (TT-ICE*). Here, we provide a proof of correctness for TT-ICE and empirically demonstrate the performance of the algorithms in compressing large-scale video and scientific simulation datasets. Compared to existing approaches that also use rank adaptation, TT-ICE* achieves 57× higher compression and up to 95% reduction in computational time.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2019

Elastic Precursor Decay and Spallation in Nonporous Tungsten Carbide Ceramics

To identify the possible contribution of relaxation processes to the resistance against high-rate deformation, evolution of shock-compression waves in tungsten carbide (WC) ceramics manufactured by spark-plasma sintering at a maximum compressive stress of 27 GPa is measured. Strong elastic precursor decay upon changing the thickness of the samples from 0.15 to 4 mm is revealed. At maximum shock compressive stresses twice exceeding the Hugoniot elastic limit, a decrease in the spall strength value by about 30% from its value in the elastic region is recorded.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Spindown of Pulsars Interacting with Companion Winds: The Impact of Magnetospheric Compression

Pulsars in binary systems with strong companion winds can have the magnetopause separating their magnetosphere from the wind located well within their light cylinder. This bow-like enclosure effectively creates a waveguide that confines the pulsar's electromagnetic fields and can significantly alter its spindown. In this paper, we study the spindown of compressed pulsar magnetospheres in such systems. We parameterize the confinement as the ratio between the equatorial position of the magnetopause (or standoff distance) R m and the pulsar's light cylinder R LC . Using particle-in-cell simulations, we quantify the pulsar spindown for a range of compressions, R m /R LC = 1/3–1, and inclination angles, χ = 0°...90°, between magnetic and rotation axes. Our strongly confined models (R m /R LC = 1/3) show two distinct limits. For χ = 0°, the spindown of a compressed pulsar magnetosphere is enhanced by approximately a factor of three compared to an isolated pulsar due to the increased number of open magnetic field lines. Conversely, for χ = 90°, the compressed pulsar spins down at less than 40% of the rate of an isolated reference pulsar due to the mismatch between the pulsar wind stripe wavelength and the waveguide size. We apply our analysis to the 2.77 s oblique rotator (χ = 60°) in the double-pulsar system PSR J0737-3039. With the numerically derived spindown estimate, we constrain its surface magnetic field to B* ≈ (7.3 ± 0.2) × 10 11 G. We discuss the time modulation of its period derivative, the effects of compression on its braking index, and implications for the radio eclipse in PSR J0737-3039.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2019

Experimental investigation of the relationship between thermal barrier coating structured porosity and homogeneous charge compression ignition engine combustion

Heat transfer has a monumental influence on homogeneous charge compression ignition combustion. When a thermal barrier coating is applied to the combustion chamber, the insulating effect magnifies the wall temperature swing, decreasing heat transfer during combustion. This enables improvements in both thermal and combustion efficiency without the detrimental impacts of intake charge heating. Increasing the temperature swing requires coatings with lower thermal conductivity and heat capacity. An enticing avenue for simultaneously decreasing both thermal conductivity and capacity is to increase the porosity fraction. A proprietary solution precursor plasma spray process enables discrete organization of the porosity structure, called inter-pass boundaries, which in turn produces a step-reduction in thermal conductivity for a given porosity level. In this investigation, yttria-stabilized zirconia is used to create four different thermal barrier coatings to study the potential of structured porosity as means of improving the “temperature swing” behavior in a homogeneous charge compression ignition engine. The baseline coating is “dense YSZ,” applied using a standard air-plasma spray process. Furthermore, significant reductions of the thermal conductivity are achieved by utilizing the solution precursor plasma spray process to create inter-pass boundaries with a moderate overall porosity. Performance, efficiency, and emissions are compared against both a baseline configuration with a metal piston and an air-plasma spray “dense YSZ” coating. Experiments are carried out in a single-cylinder gasoline homogeneous charge compression ignition engine with exhaust re-induction. Experiments indicate that incorporating structured porosity into thermal barrier coatings produces tangible gains in combustion and thermal efficiencies. However, there is an upper limit to porosity levels acceptable for homogeneous charge compression ignition engine application because an elevated porosity fraction leads to excessive surface roughness and undesirable fuel interactions. Comparison of the coatings showed the best results with coating thickness of up to 150 µm. Thicker coatings led to slower surface temperature response and attenuated swing temperature magnitude.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Hydrodynamic instabilities and heat transfer characteristics in the duct flow of a fluid in the supercritical thermodynamic regime

The behavior of fluids at supercritical thermodynamic conditions is inherently complex due to large variations in thermodynamic and transport properties. Recent numerical and experimental investigations illustrate ongoing interest for these fluids, especially supercritical CO 2 and supercritical water, for a variety of applications. For example, supercritical water reactors (SCWR) operate in this extreme condition of high-pressure and temperature, resulting in highly dynamic flow fields and unexpected heat transfer regimes. The potential heat transfer benefits in this regime are directly associated with the extreme variations in thermodynamic and transport properties, which occur at, and above, the critical point. This work characterizes the hydrodynamic instabilities that arise for fluids at supercritical thermodynamic conditions when buoyancy forces are significant. Two specific configurations are considered, a natural convection cavity flow, and a mixed convection, heated, horizontal channel flow. Natural convection flow in a cavity is a classical configuration with expected behavior below the critical point. This configuration aids in characterizing the effect of the variable properties in the supercritical thermodynamic regime. Further, limited studies in the existing literature have been conducted for low-Reynolds and intermediate-Rayleigh numbers, mixed-convection channel flows for supercritical water, which is the focus of the channel flow configuration. To investigate the thermally driven hydrodynamic instabilities in this regime, a high-order fully-implicit numerical method is used. Such strong variations in thermophysical properties (in particular, density) are difficult to simulate and an altogether compressible framework is needed. Therefore, the compressible Navier-Stokes equations are solved without any additional assumptions. The fully implicit, high-order in space and time, reconstructed discontinuous Galerkin method as implemented within the multi-physics code called ALE3D (Arbitrary Lagrangian and Eulerian in 2D and 3D), developed at Lawrence Livermore National Laboratory (LLNL), is used. This fully implicit, L-stable method accurately captures the compressible nature of the ow in the limit of very low Mach number. It has been widely accepted that above the critical point, only one phase is observed. However, recent research has indicated the existence of the distinct gas-like and liquid-like regions separated by the Widom line, the locus of the maxima of the specific heat. Along the Widom line, density decreases 6-fold, viscosity drops by a factor of 2, while specific heat spikes by an order of magnitude. These variations, specifically in density and viscosity, produce a thick pseudo-interface and flow dynamics behavior akin to film boiling. A pseudo-film at the heated wall of the cavity and the horizontal channel is observed where buoyancy forces induce mixing through the specific configurations. Further the local Rayleigh and Richardson numbers provide maps of the flow field and the buoyancy forces driving the microscopic mixing. In the first chapter, I describe a background of supercritical fluid and the various applications. The second chapter focuses on the mathematical model and numerical method used for simulations, where a description of the equation of state for supercritical water is described. The third chapter focuses on the natural convection cavity with a heated bottom wall. In this cavity a gas-like and a liquid-like flow within the supercritical thermodynamic regime are observed. The fourth chapter focuses on a forced convection, horizontal channel, distinguishing between the gas-like, liquid-like, and mixed flow regimes. Mixed convection flow, with the addition of gravitational forces in the horizontal channel show the influence of variable properties on the hydrodynamic development, heat transfer, and rising instabilities. The last chapter of this research focuses on characterizing the unstable hydrodynamics through time-averaging processes and analysis of the movement of energy through the developing plumes.

42 ENGINEERING↗
DOE OSTI2023

Compressive strength improvements from noncircular carbon fibers: A numerical study

The benefits of high-performance unidirectional carbon fiber composites are limited in many cost-driven industries due to the high cost relative to alternative reinforcement fibers. Low-cost carbon fibers have been previously proposed, but the longitudinal compressive strength continues to be a limiting factor or studies are based on simplifications that warrant further analysis. A micromechanical model is used to (1) determine if the longitudinal compressive strength of composites can be improved with noncircular carbon fiber shapes and (2) characterize why some shapes are stronger than others in compression. In comparison to circular fibers, the results suggest that the strength can be increased by 10%–13% by using a specific six-lobe fiber shape and by 6%–9% for a three-lobe fiber shape. A slight increase is predicted in the compressive strength of the study two-lobe fiber but has the highest uncertainty and sensitivity to fiber orientation and misalignment direction. The underlying mechanism governing the compressive failure of the composites was linked to the unique stress fields created by the lobes, particularly the pressure stress in the matrix. Importantly, this work provides mechanics-based evidence of strength improvements from noncircular fiber shapes and insight on how matrix yielding is altered with alternative fiber shapes.

36 MATERIALS SCIENCE↗
NASA NTRS2014

Grid Resolution Study over Operability Space for a Mach 1.7 Low Boom External Compression Inlet

This paper presents a statistical methodology whereby the probability limits associated with CFD grid resolution of inlet flow analysis can be determined which provide quantitative information on the distribution of that error over the specified operability range. The objectives of this investigation is to quantify the effects of both random (accuracy) and systemic (biasing) errors associated with grid resolution in the analysis of the Lockheed Martin Company (LMCO) N+2 Low Boom external compression supersonic inlet. The study covers the entire operability space as defined previously by the High Speed Civil Transport (HSCT) High Speed Research (HSR) program goals. The probability limits in terms of a 95.0% confidence interval on the analysis data were evaluated for four ARP1420 inlet metrics, namely (1) total pressure recovery (PFAIP), (2) radial hub distortion (DPH/P), (3) ) radial tip distortion (DPT/P), and (4) ) circumferential distortion (DPC/P). In general, the resulting +/-0.95 delta Y interval was unacceptably large in comparison to the stated goals of the HSCT program. Therefore, the conclusion was reached that the "standard grid" size was insufficient for this type of analysis. However, in examining the statistical data, it was determined that the CFD analysis results at the outer fringes of the operability space were the determining factor in the measure of statistical uncertainty. Adequate grids are grids that are free of biasing (systemic) errors and exhibit low random (precision) errors in comparison to their operability goals. In order to be 100% certain that the operability goals have indeed been achieved for each of the inlet metrics, the Y+/-0.95 delta Y limit must fall inside the stated operability goals. For example, if the operability goal for DPC/P circumferential distortion is ≤0.06, then the forecast Y for DPC/P plus the 95% confidence interval on DPC/P, i.e. +/-0.95 delta Y, must all be less than or equal to 0.06.

Grid↗
NASA NTRS1959

Design of Axisymmetric Exhaust Nozzles by Method of Characteristics Incorporating a Variable Isentropic Exponent

Limitations on fully developed laminar flows due to compressibility and property variations are examined. The cases, for liquids and for gases, wherein such motions are "exact" are determined and solutions are given. For more general conditions, not permitting an exact fully developed flow, limitations are set. Two cases arise depending on the size of the temperature variation across the channel. Both the forced and free flow are solved for the case of large temperature variation. Finally, there are described briefly some circumstances under which streamwise variations of velocity occur. The case where the velocity varies inversely with the square root of the distance is solved.

Guentert, Eleanor Costilow↗
NASA NTRS1992

A compressible near-wall turbulence model for boundary layer calculations

A compressible near-wall two-equation model is derived by relaxing the assumption of dynamical field similarity between compressible and incompressible flows. This requires justifications for extending the incompressible models to compressible flows and the formulation of the turbulent kinetic energy equation in a form similar to its incompressible counterpart. As a result, the compressible dissipation function has to be split into a solenoidal part, which is not sensitive to changes of compressibility indicators, and a dilational part, which is directly affected by these changes. This approach isolates terms with explicit dependence on compressibility so that they can be modeled accordingly. An equation that governs the transport of the solenoidal dissipation rate with additional terms that are explicitly dependent on the compressibility effects is derived similarly. A model with an explicit dependence on the turbulent Mach number is proposed for the dilational dissipation rate. Thus formulated, all near-wall incompressible flow models could be expressed in terms of the solenoidal dissipation rate and straight-forwardly extended to compressible flows. Therefore, the incompressible equations are recovered correctly in the limit of constant density. The two-equation model and the assumption of constant turbulent Prandtl number are used to calculate compressible boundary layers on a flat plate with different wall thermal boundary conditions and free-stream Mach numbers. The calculated results, including the near-wall distributions of turbulence statistics and their limiting behavior, are in good agreement with measurements. In particular, the near-wall asymptotic properties are found to be consistent with incompressible behavior; thus suggesting that turbulent flows in the viscous sublayer are not much affected by compressibility effects.

So, R. M. C.↗
NASA NTRS2004

Cardiopulmonary Resuscitation in Lunar and Martian Gravity Fields

Cardiopulmonary resuscitation is required training for all astronauts. No studies thus far have investigated how chest compressions may be affected in lunar and Martian gravities. Therefore a theoretical quantitative study was performed. The maximum downward force an unrestrained person can apply is mg N (g(sub Earth) = 9.78 ms(sup -2), g(sub moon) = 1.63 ms(sup -2), g(sub Mars) = 3.69 ms(sup -2). Tsitlik et a1 (Critical Care Medicine, 1983) described the human sternal elastic force-displacement relationship (compliance) by: F = betaD(sub s) + gammaD(sub s)(sup 2) (beta = 54.9 plus or minus 29.4 Ncm(sup -1) and gamma = 10.8 plus or minus 4.1 Ncm(sup -2)). Maximum forces in the 3 gravitational fields produced by 76 kg (US population mean), 41 kg and 93 kg (masses derived from the limits for astronaut height), produced solutions for compression depth using Tsitlik equations for chests of: mean compliance (beta = 54.9, gamma = 10.8), low compliance (beta = 84.3, gamma = 14.9) and high compliance (beta = 25.5, gamma = 6.7). The mass for minimum adequate adult compression, 3.8 cm (AHA guidelines), was also calculated. 76 kg compresses the mean compliance chest by: Earth, 6.1 cm, Mars, 3.2 cm, Moon, 1.7 cm. In lunar gravity, the high compliance chest is compressed only 3.2 cm by 93 kg, 120 kg being required for 3.8 cm. In Martian gravity, on the mean chest, 93 kg compresses 3.6 cm; 99 kg is required for 3.8 cm. On Mars, the high compliance chest is compressed 4.8 cm with 76 kg, 5.5 cm with 93 kg, with 52 kg required for 3.8 cm.

Sarkar, Subhajit↗
DOE OSTI2024

Synthesis and Properties of the Helium Clathrate and Defect Perovskite [He 2– x $^\square$ x ][CaNb]F 6

The defect double perovskite [He 2– x $^\square$ x ][CaNb]F 6 , with helium on its A-site, can be prepared by the insertion of helium into ReO 3 -type CaNbF 6 at high pressure. Upon cooling from 300 to 100 K under 0.4 GPa helium, ~60% of the A-sites become occupied. Helium uptake was quantified by both neutron powder diffraction and gas insertion and release measurements. After the conversion of gauge pressure to fugacity, the uptake of helium by CaNbF 6 can be described by a Langmuir isotherm. The enthalpy of absorption for helium in [He 2– x $^\square$ x ][CaNb]F 6 is estimated to be ~+3(1) kJ mol –1 , implying that its formation is entropically favored. Helium is able to diffuse through the material on a time scale of minutes at temperatures down to ~150 K but is trapped at 100 K and below. The insertion of helium into CaNbF 6 reduces the magnitude of its negative thermal expansion, increases the bulk modulus, and modifies its phase behavior. On compressing pristine CaNbF 6 , at 50 and 100 K, a cubic (Fm$\overline{3}$m) to rhombohedral (R$\overline{3}$) phase transition was observed at <0.20 GPa. However, a helium-containing sample remained cubic at 0.4 GPa and 50 K. CaNbF 6 , compressed in helium at room temperature, remained cubic to >3.7 GPa, the limit of our X-ray diffraction measurements, in contrast to prior reports that upon compression in a nonpenetrating medium, a phase transition is detected at ~0.4 GPa.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗