SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The structure of π-Ti 2 O(PO 4 ) 2 ·2H 2 O was determined by the SR-PXRD method. The proton conductivity of chitosan/π-TiP membranes reached 4.5 × 10 −3 S cm −1 at 95%-RH.
Organosolv treatment is an environmentally friendly fractionation method that affords a lignin stream with high purity.
Polymer toughness is typically dictated by the entanglement density. Here we demonstrate a new paradigm via polymer-grafted nanocomposites that couples segmental dynamics with the entanglement concept for enhanced toughness at high deformation rates.
Cation off-centering is crystallography frustrated in the pyrochlore but exhibits local ordering.
Ambient soot particles significantly impact Earth’s radiative balance, human health, and atmospheric visibility. Their microstructural properties depend on formation and aging mechanisms, which vary by emission source and atmospheric processes. Hence, accurately identifying sources of soot enhances our understanding of their physicochemical properties and atmospheric implications. This study used a multi-modal approach to characterize and attribute sources of submicron soot particles collected in Israel during new particle formation events, biomass burning episodes, and background atmospheric conditions. Synchrotron-based X-ray microscopy was used to map soot (elemental carbon), organic carbon, and inorganic species. Implemented atomic force microscopy showed highly diverse phase states, with soot consistently exhibiting a solid-like phase. Automated µ-Raman analysis was subsequently performed on ~690 particles, identifying three soot classes based on spectral features corresponding to the "Defect" (D) and "Graphite" (G) bands of soot. We applied two-peak and five-peak fitting approaches to deconvolute the “Defect” peaks (D1, D2, D3, and D4) and G band from average Raman, revealing varying degrees of graphitic order. The degree of graphitic order was determined from metrics such as the D3 peak area, often observed when soot was internally mixed with organic material. Raman spectral features, along with temporal variations in particle classes contributions, suggest that Particle Type 1 corresponds to traffic related soot and Particle Type 2 to less graphitic soot from biomass burning, while Particle Type 3 is associated with more heterogeneous particulate representative of soot-OC mixtures emitted during new particle formation and biomass burning episodes.
Macrohomogeneous battery models are widely used to predict battery performance, necessarily relying on effective electrode properties, such as specific surface area, tortuosity, and electrical conductivity. While these properties are typically estimated using ideal effective medium theories, in practice they exhibit highly non-ideal behaviors arising from their complex mesostructures. In this paper, we computationally reconstruct electrodes from X-ray computed tomography of 16 nickel–manganese–cobalt-oxide electrodes, manufactured using various material recipes and calendering pressures. Due to imaging limitations, a synthetic conductive binder domain (CBD) consisting of binder and conductive carbon is added to the reconstructions using a binder bridge algorithm. Reconstructed particle surface areas are significantly smaller than standard approximations predicted, as the majority of the particle surface area is covered by CBD, affecting electrochemical reaction availability. Finite element effective property simulations are performed on 320 large electrode subdomains to analyze trends and heterogeneity across the electrodes. Significant anisotropy of up to 27% in tortuosity and 47% in effective conductivity is observed. Electrical conductivity increases up to 7.5× with particle lithiation. We compare the results to traditional Bruggeman approximations and offer improved alternatives for use in cell-scale modeling, with Bruggeman exponents ranging from 1.62 to 1.72 rather than the theoretical value of 1.5. We also conclude that the CBD phase alone, rather than the entire solid phase, should be used to estimate effective electronic conductivity. This study provides insight into mesoscale transport phenomena and results in improved effective property approximations founded on realistic, image-based morphologies.
Abstract not provided
Explore the source record for details and available documents.
The theory of cold aggregation of interstellar dust into comets is shown to support the ideas that comets provided not only a substantial part of the earth's water but also of its complex organic surface material. Comparison of the density of interstellar dust with meteor densities leads to the conclusion that comets are very fluffy bodies whose solid matter occupies no more than 2/5 of the total volume and possibly substantially less. This implies an extremely low comet albedo of about 0.05 in the visual even for slightly absorbing individual components.
The influence is investigated of a curvilinear fiber format on load carrying capacity of a layered fiber reinforced plate with a centrally located hole. A curvilinear fiber format is descriptive of layers in a laminate having fibers which are aligned with the principal stress directions in those layers. Laminates of five curvilinear fiber format designs and four straightline fiber format designs are considered. A quasi-isotropic laminate having a straightline fiber format is used to define a baseline design for comparison with the other laminate designs. Four different plate geometries are considered and differentiated by two values of hole diameter/plate width equal to 1/6 and 1/3, and two values of plate length/plate width equal to 2 and 1. With the plates under uniaxial tensile loading on two opposing edges, alignment of fibers in the curvilinear layers with the principal stress directions is determined analytically by an iteration procedure. In-plane tensile load capacity is computed for all of the laminate designs using a finite element analysis method. A maximum strain failure criterion and the Tsai-Wu failure criterion are applied to determine failure loads and failure modes. Resistance to buckling of the laminate designs to uniaxial compressive loading is analyzed using the commercial code Engineering Analysis Language. Results indicate that the curvilinear fiber format laminates have higher in-plane tensile load capacity and comparable buckling resistance relative to the straightline fiber format laminates.
The gains in buckling performance are explored that can be achieved by deviating from the conventional straightline fiber format and considering the situation whereby the fiber orientation in a layer, or a group of layers, can vary from point to point. The particular situation studied is a simply supported square plate with a centrally located hole loaded in compression. By using both a sensitivity analysis and a gradient-search technique, fiber orientation in a number of regions of the plate are selected so as to increase the buckling load relative to baseline straightline designs. The sensitivity analysis is used to determine which regions of the plate have the most influence on buckling load, and the gradient search is used to find the design that is believed to represent the absolute maximum buckling load for the conditions prescribed. Convergence studies and sensitivity of the final design are discussed. By examining the stress resultant contours, it is shown how the curvilinear fibers move the load away from the unsupported hole region of the plate to the supported edges, thus increasing the buckling capacity. The tensile capacity of the improved buckling design is investigated, and it is shown that both tensile capacity and buckling capacity can be improved with the curvilinear fiber concept.
The gains in structural efficiency are investigated that can be achieved by aligning the fibers in some or all of the layers in a laminate with the principal stress directions in those layers. The name curvilinear fiber format is given to this idea. The problem studied is a plate with a central circular hole subjected to a uniaxial tensile load. An iteration scheme is used to find the fiber directions at each point in the laminate. Two failure criteria are used to evaluate the tensile load capacity of the plates with a curvilinear format, and for comparison, counterpart plates with a conventional straightline fiber format. The curvilinear designs for improved tensile capacity are then checked for buckling resistance. It is concluded that gains in efficiency can be realized with the curvilinear format.
Hercules IM7/8552 carbon/epoxy and Hysol EA 9394 epoxy adhesive bonded between composite/titanium were tested for permeability after various numbers of thermal cycles between 100 C and liquid nitrogen (-196 C). The specimens were quenched from the 100 C temperature into liquid nitrogen to induce thermal shock into the material. Results showed that the carbon/epoxy system was practically impermeable even after 12 thermal cycles. The EA 9394 adhesive bondline was more permeable than the carbon/epoxy, but vacuum mixing minimized the permeability and kept it within allowable limits. Thermal cycling had little effect on the permeability values of the bondline specimens.
Thermoplastic laminates in situ consolidated via tape or tow placement require full mechanical properties. Realizing full properties requires resin crystallinity to be controlled - partial crystallinity leads to unacceptably low laminate compression properties. There are two approaches: utilize an amorphous matrix resin; or place material made from a semi-crystalline resin featuring kinetics faster than the process. In this paper, a matrix resin evaluation and trade study was completed with commercial and NASA amorphous polyimides on the one hand, and with PEKK mixed with POSS nanoparticles for accelerated crystallinity growth on the other. A new thermoplastic impregnated material, 6 mm wide (0.25-in) AS-4 carbon/LaRC(TradeMark)8515 dry polyimide tow, was fabricated. Since LaRC(TradeMark)8515 is fully amorphous, it attains full properties following in situ consolidation, with no post processing required to build crystallinity. The tow in situ processing was demonstrated via in situ thermoplastic filament winding it into rings.
No abstract available
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.